Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Resistivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Rolling resistance of electric vehicle tires from track tests

Special low-rolling-resistance tires were made for DOE's ETV-1 electric vehicle. Tests were conducted on these tires and on a set of standard commercial automotive tires to determine the rolling resistance as a function of time during both constant-speed tires and SAE J227a driving cycle tests. The tests were conducted on a test track at ambient temperatures that ranged from 15 to 32 C (59 to 89 F) and with tire pressures of 207 to 276 kPa (30 to 40 psi). At a contained-air temperature of 38 C (100 F) and a pressure of 207 kPa (30 psi) the rolling resistances of the electric vehicle tires and the standard commercial tires, respectively, were 0.0102 and 0.0088 kilogram per kilogram of vehicle weight. At a contained-air temperature of 38 C (100 F) and a pressure of 276 kPa (40 psi) the rolling resistances were 0.009 and 0.0074 kilogram per kilogram of vehicle weight, respectively.

Dustin, M. O.↗

Effect of mechanical surface and heat treatments on erosion resistance

The effect of erosion by glass beads and crushed glass and by heat treatments on the erosional resistance of 6061 aluminum alloy and 1045 steel were studied. The aluminum alloy's erosion resistance was found to be insensitive to mechanical surface treatment applied before testing, and was determined to depend on the properties of the work-hardened surface layer; this was also demonstrated for aluminum alloy single crystals. The aluminum alloy heat treatments included annealing, solution, and precipitation. Solution was found to increase erosion resistance but precipitation had the opposite effect. Hardness showed no correlation with erosion resistance for either aluminum alloy steel. The steel tests showed that crushed glass provides an order of magnitude more erosion than glass beads.

Salik, J.↗

Airflow resistivity instrument for in situ measurement on the earth's ground surface

An airflow resistivity instrument features a novel specimen holder, especially designed for in situ measurement on the earth's ground surface. This capability eliminates the disadvantages of prior intrusive instruments, which necessitate the removal of a test specimen from the ground. A prototype instrument can measure airflow resistivities in the range 10-5000 cgs rayl/cm, at specimen depths up to 15.24 cm (6 in.), and at differential pressures up to 2490.8 dyn sq cm (1 in. H2O) across the specimen. Because of the close relationship between flow resistivity and acoustic impedance, this instrument should prove useful in acoustical studies of the earth's ground surface. Results of airflow resistivity measurements on an uncultivated grass field for varying values of moisture content are presented.

Zuckerwar, A. J.↗

Constant-Operating-Resistance Hot-Wire Probe

Effects of lead-wire-resistance changes with temperature nullified. Constant-operating-resistance hot-wire probe uses two sets of leads. Exposed to identical conditions, comparison of resistance gives change in sensing element itself. Data taken in more convenient manner, with advantage of not having to constantly check for possible changes in lead resistance and consequently readjust potentiometer.

Stainback, P. C.↗

Thin N-I-P radiation resistant solar cells

Several sets of N-I-P sola cells were fabricated from high resistivity silicon to test the effectiveness of various methods for hardening these devices against radiation. Different substrate materials were used to provide information on the effects of dopant concentration, silicon type, and the presence of oxygen. In some cells, P-type float-zone refined silicon of 800, 8000 and 15,000 omega-cm resistivity was used to provide a basis for studying resistivity and purity effects. In other cells, N-type silicon (approximately 800 omega-cm) was used to allow a comparison of dopant type. Oxygen-rich, crucible-grown, silicon (approximately 100 omega-cm, p-type) will provide information on purity effects and defect gettering. Lithium was introduced into different types of silicon to determine if mobile ions can reduce radiation induced defects in high resistivity material. Thin cells (2 mil) were fabricated to study the effects of cell thickness and carrier injection on radiation damage. The electrical characteristics of the different sets of cells were measured, analyzed, and compared prior to shipment of the cells to NASA/Lewis for irradiation.

Meulenberg, A.↗

Oxidation and corrosion resistance of candidate Stirling engine heater-head-tube alloys

Sixteen candidate iron base Stirling engine heater head tube alloys are evaluated in a diesel fuel fired simulator materials test rig to determine their oxidation and corrosion resistance. Sheet specimens are tested at 820 C for 3500 hr in 5 hr heating cycles. Specific weight change data and an attack parameter are used to categorize the alloys into four groups; 10 alloys show excellent for good oxidation and corrosion resistance and six alloys exhibit poor or catastrophic resistance. Metallographic, X-ray, and electron microprobe analyses aid in further characterizing the oxidation and corrosion behavior of the alloys. Alloy compositions, expecially the reactive elements aluminum, titanium, and chromium, play a major role in the excellent oxidation and corrosion behavior of the alloys. The best oxidation resistance is associated with the formation of an iron nickel aluminum outer oxide scale, an intermediate oxide scale rich in chromium and titanium, and an aluminum outer oxide scale adjacent to the metallic substrate, which exhibits a zone of internal oxidation of aluminum and to some extent titanium.

Stephens, J. R.↗

Thermoplastic composite matrices with improved solvent resistance

In order to improve solvent resistance of aromatic thermoplastic polymers, ethynyl-terminated aromatic sulfone polymers (ETS), sulfone/ester polymers (SEPE) containing pendent ethynyl groups, and phenoxy resin containing pendent ethynyl groups are synthesized. Cured polysulfones and phenoxy resins containing ethynyl groups on the ends or pendent on the molecules exhibited systematic behavior in solvent resistance, film flexibility, and toughness as a function of crosslink density. The film and composite properties of a cured solvent-resistant ETS were better than those of a commercially available solvent sensitive polysulfone. The study was part of a NASA program to better understand the trade-offs between solvent resistance, processability and mechanical properties which may be useful in designing composite structures for aerospace vehicles.

Hergenrother, P. M.↗

Radiation damage in high-resistivity silicon solar cells

High-resistivity silicon solar cells exhibit reduced radiation damage when light is incident on the gridded back surface. Under back illumination, radiation damage decreases as cell resistivity increases; under front illumination, radiation damage increases as cell resistivity increases. Thin back-illuminated cells outperform conventional 10 omega cm 50 and 200 micron cells at low 1-MeV electron fluences. However, at higher fluences, the conventional cells exhibit superior radiation resistance. This is attributed to the low BOL diffusion lengths observed in the thin, sack-illuminated cell. These results are discussed in terms of injected charge distributions, electric fields in the cell base, and the effects of a dominant boron-oxygen defect.

Weinberg, I.↗

Fundamental Studies of Low Velocity Impact Resistance of Graphite Fiber Reinforced Polymer Matrix Composites

A study was conducted to relate the impact resistance of graphite fiber reinforced composites with matrix properties through gaining an understanding of the basic mechanics involved in the deformation and fracture process, and the effect of the polymer matrix structure on these mechanisms. It was found that the resin matrix structure influences the composite impact resistance in at least two ways. The integration of flexibilizers into the polymer chain structure tends to reduce the T sub g and the mechanical properties of the polymer. The reduction in the mechanical properties of the matrix does not enhance the composite impact resistance because it allows matrix controlled failure to initiate impact damage. It was found that when the instrumented dropweight impact tester is used as a means for assessing resin toughness, the resin toughness is enhanced by the ability of the clamped specimen to deflect enough to produce sufficient membrane action to support a significant amount of the load. The results of this study indicate that crossplied composite impact resistance is very much dependent on the matrix mechanical properties.

Bowles, K. J.↗

Low-temperature deposition of low resistivity ZnSe films by reactive sputtering

The use of reactive dc magnetron cosputtering of Zn and the dopant In in an H2Se/Ar gaseous mixture is described. It is observed that initial deposition using pure Zn targets produced yellowish transparent ZnSe films on glass with a film resistivity of 10 to the 8th ohms cm and deposition using a Zn target doped with a fixed 1 percent of In produced ZnSe films with resistivities of about 10,000 ohms cm. The improvement of film conductivity by optimizing the In content in the ZnSe films is discussed; the ZnSe resistivity dependence on In flux is studied. Optical absorption/transmission measurements reveal a photon energy band gap of 2.65 eV at room temperature and X-ray diffraction show highly oriented polycrystalline films on glass with the c axis parallel to the plane of the film. Compositional analysis was performed and the Zn/Se ratio is measure as 48.8/49.0 with an In concentration of 1.16 percent. ZnSe films deposited on glass and conducting SnO2-coated glass substrates with a resistance of 20 ohms cm and a substrate temperature of 120 C have been fabricated.

Stirn, R. J.↗

Simultaneous electrical resistivity and mass uptake measurements in bromine intercalated fibers

Changes in mass and electrical resistivity of several types of pitch-based and vapor-grown graphite fibers were monitored during reaction with bromine. The observed threshold pressure dependent reaction suggested that the fibers were intercalated. In the fully brominated compound, the mass was increased by 44 percent and the resistivity was improved by a factor of 17. In the residue compound, the mass was increased by 22 percent and the resistivity was improved by a factor of 5. Fibers possessing different degrees of graphitization had surprisingly similar changes in both mass and resistivity.

Jaworske, D. A.↗

Resistive ballooning modes in line-tied coronal arcades

The equations describing the linear evolution of resistive ballooning modes are obtained by using a modified WKB expansion in the short perpendicular wavelength, while variations of the perturbations along the field are described by a slowly varying amplitude, on which the tying boundary conditions are imposed. In general, given an equilibrium, there are certain ranges of magnetic surfaces for which the system predicts instability even without dissipation. The main conclusion is that within the resistive MHD approximation cylindrically symmetric arcades with pressure falling with radius are unstable to resistive localized modes; the growth rates, close to ideal marginal stability, are large, so that it would appear that energy could be released during 10 to 100 Alfven times. The wavelength of the modes is expected to be limited by the ion gyroradius, when stabilizing drift effects must be taken into account. The nonlinear evolution of resistive ballooning modes should be studied to assess their overall relevance to the violent and rapidly evolving phenomena observed on the sun.

Velli, Marco↗

New flange correction formula applied to interfacial resistance measurements of ohmic contacts to GaAs

A quasi-two-dimensional analytical model is developed to account for vertical and horizontal current flow in and adjacent to a square ohmic contact between a metal and a thin semiconducting strip which is wider than the contact. The model includes side taps to the contact area for voltage probing and relates the 'apparent' interfacial resistivity to the (true) interfacial resistivity, the sheet resistance of the semiconducting layer, the contact size, and the width of the 'flange' around the contact. This relation is checked against numerical simulations. With the help of the model, interfacial resistivities of ohmic contacts to GaAs were extracted and found independent of contact size in the range of 1.5-10 microns.

Lieneweg, Udo↗

Electrical Properties of Materials for Elevated Temperature Resistance Strain Gage Application

The objective was to study the electrical resistances of materials that are potentially useful as resistance strain gages at 1000 C. Transition metal carbides and nitrides, boron carbide and silicon carbide were selected for the experimental phase of this research. Due to their low temperature coefficient of resistance and good stability, TiC, ZrC, B sub 4 C and beta-SiC are suggested as good candidates for high temperature resistance strain gage applications.

Lei, Jih-Fen↗

Electrical resistivity (4K to 2100K) of annealed vapor growth carbon fibers

Carbon fibers have been grown from methane gas, on iron seeded substrates at 1370 K, and subsequently annealed to a series of temperatures between 2800 K and 3475 K. The subsequent measurement of the electrical resistivity are reported as a function of temperature from 4 K to 2100 K. The two band model for the resistivity of graphite is well fit to the data, and results in physically reasonable parameters of the fits. The resistivity vs temperature results for two boron doped fibers are reported as well. The product of the resistivity times density for these fibers is lower than that product for any refractory metal, for temperatures above about 1000 K, suggesting the usefulness of these fibers as high temperature materials in space applications.

Ahmed, Akhter U.↗

Current-driven resistive ballooning modes in axially bounded solar flare plasmas

The most unstable current-driven resistive modes of an axially bounded coronal loop are found in computer simulations to exhibit the spatial structure of ballooning modes. The observed modes are not confined to mode rational surfaces, but instead have broad radial extent. A theory assuming ballooning mode spatial structure predicts that a minimum current should be required for linear instability, and that, when the mode is unstable, the linear growth rate scales linearly with the resistivity eta below a critical resistivity, and scales as cu root of eta for larger resistivities. Both predictions are borne out by simulation results. Both theory and simulation analyses of the mode suggest that the strong radial structure of the mode near the ends of the system is the primary contributing factor to the instability of the mode. A helical current sheet is formed in the nonlinear evolution of the mode near the edge of the current channel and is accompanied by a strong radial gradient in the current and partial current reversal.

Otani, Niels F.↗

Radiation resistance and comparative performance of ITO/InP and n/p InP homojunction solar cells

The radiation resistance of ITO/InP cells processed by DC magnetron sputtering is compared to that of standard n/p InP and GaAs homojunction cells. After 20 MeV proton irradiations, it is found that the radiation resistance of the present ITO/InP cell is comparable to that of the n/p homojunction InP cell and that both InP cell types have radiation resistance significantly greater than GaAs. The relatively lower radiation resistance, observed at higher fluence, for the InP cell with the deepest junction depth, is attributed to losses in the cells emitter region. Diode parameters obtained from I sub sc - V sub oc plots, data from surface Raman spectroscopy, and determinations of surface conductivity types are used to investigate the configuration of the ITO/InP cells. It is concluded that thesee latter cells are n/p homojunctions, the n-region consisting of a disordered layer at the oxide semiconductor.

Weinberg, I.↗

RF surface resistance of YBa2Cu3O(7-x) thin films

The excitement engendered by the discovery of the new T sub c oxide superconductors has led to much speculation about practical applications of thin films of these materials in digital and analog electronic devices. Most of these envisioned applications involve high frequency signals for which a detailed knowledge of the surface impedance of the novel superconductors is very important. We have measured the surface resistance of thin films of YBaCuO in the frequency range 0.5 less than f less than 17 GHz using a stripline-resonator method. The stripline procedure also was used to measure the surface resistance of high quality gold and aluminum films; the resistance values obtained agree with values predicted from the measured dc resistance using the Pippard formalism for the anomalous skin effect. The YBaCuO were produced by a multilayer deposition process. The films are formed by e-beam evaporation of 24 layers of Y, Ba, and Cu. Films with the highest transition temperature were obtained using yttria-stabilized zirconia (YSZ) substrates. After deposition, the films are transferred to a furnace where they are annealed in flowing O2 at 850 C for 2h. The furnace then is turned off and allowed to cool to 100 C in about 16 h. Auger profiling of the films made by this process shows that the concentrations of Y, Ba, Cu, and O are uniform to within 1 percent throughout the thickness of the film.

Source record↗