Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Photocurrent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Effect of the femtosecond laser treatment of hydrogenated amorphous silicon films on their structural, optical, and photoelectric properties

The effect of the femtosecond laser treatment of hydrogenated amorphous silicon (a-Si:H) films on their structural, optical, and photoelectric properties is studied. Under the experimental conditions applied in the study, laser treatment of the film with different radiation intensities induces structural changes that are nonuniform over the film surface. An increase in the radiation intensity yields an increase in the contribution of the nanocrystalline phase to the structure, averaged over the sample surface, as well as an increase in the conductance and photoconductance of the samples. At the same time, for all of the samples, the absorption spectrum obtained by the constant-photocurrent method has a shape typical for those of amorphous silicon. Obtained results indicate the possibility of a-Si:H films photoconductance increase by femtosecond pulse laser treatment.

36 MATERIALS SCIENCE↗

Improvement in the quantum sensitivity of InAs/InAsSb/InAsSbP heterostructure photodiodes

InAs/InAs{sub 0.88}Sb{sub 0.12}/InAs{sub 0.50}Sb{sub 0.20}P{sub 0.30} heterostructure photodiodes operating at room temperature in the spectral range 1-4.8 {mu}m are developed. It is shown that the formation of a curvilinear reflecting surface constituted by a number of hemispheres on the rearside of the photodiode chip leads to an increase in the quantum sensitivity of the photodiodes by a factor of 1.5-1.7 at wavelengths in the range 2.2-4.8 {mu}m. At an exposed photodiode area of 0.9 mm{sup 2} and a p-n junction area of 0.15 mm{sup 2}, a zero-bias differential resistance of 30 {Omega} and a quantum sensitivity of 0.24 electron/photon at a wavelength of 3 {mu}m are obtained. The operation of a photodiode with re-reflection of the photon flux in the crystal due to reflection from the curvilinear surface of the rearside of the photodiode chip is theoretically analyzed. The possibility of effective conversion of the re-reflected flux of photons into a photocurrent, with a simultaneous decrease in the p-n junction area, is demonstrated. An increase in the quantum sensitivity in the short-wavelength spectral range 1-2.2 {mu}m by 35% relative to the calculated data is observed, which is probably due to impact ionization in the narrow-gap active region.

36 MATERIALS SCIENCE↗

Features of impurity photoconductivity in Si:Er/Si epitaxial diodes

The photocurrent spectra of Si:Er/Si epitaxial diode structures are studied. It is shown that the nature of the sub-band-gap photoresponse is determined by the epitaxial growth temperature of the Si:Er layer and is not related to the composition of erbium emission centers. It is found that the absorption of light with photon energies lower than the energy-gap of silicon is determined by impurity-defect complexes that appear during the growth of the epitaxial layer and form a quasi-continuous spectrum of states in the energy gap of silicon. It is assumed that these impurity centers are not related to optically active erbium centers and are not involved in excitation-energy transfer to the rare-earth impurity.

36 MATERIALS SCIENCE↗

Specific features of the nonradiative relaxation of Er{sup 3+} ions in epitaxial Si structures

The specific features of the nonradiative relaxation of Er{sup 3+} ions in Si:Er layers grown by sublimation molecular-beam epitaxy (SMBE) are studied. In Si:Er/Si diode structures containing precipitation-type emitting centers, a resonance photoresponse at the wavelength λ ≈ 1.5 μm is observed, which is indicative of the nonradiative relaxation of Er3+ ions via the energy back-transfer mechanism. Saturation of the erbium-related photocurrent is for the first time observed at high temperatures. This allows estimation of the concentration of Er centers that undergo relaxation via the above-mentioned back-transfer mechanism (N{sub 0} ≈ 5 × 10{sup 16} cm{sup −3}). In terms of order of magnitude, the estimated concentration N{sub 0} corresponds to the concentration of optically active Er ions upon excitation of the Si:Er layers by means of the recombination mechanism. The features of the nonradiative relaxation of Er{sup 3+} ions in Si:Er/Si structures with different types of emitting centers are analyzed.

36 MATERIALS SCIENCE↗

Increase in the diffusion length of minority carriers in Al{sub x}Ga{sub 1–x}N alloys ({sub x} = 0–0.1) fabricated by ammonia molecular beam epitaxy

The room-temperature diffusion length of minority carriers in n-Al{sub 0.1}Ga{sub 0.9}N layers grown by ammonia molecular beam epitaxy on sapphire (0001) substrates used in structures for ultraviolet photodetectors is studied. Measurements were performed using the spectral dependence of the photocurrent recorded in a built-in p–n junction for thin samples and using the induced electron-current procedure for films up to 2 µm thick. The results show that the hole diffusion length in n-AlGaN films is 120–150 nm, which is larger than in GaN films grown under similar growth conditions by a factor of 3–4. This result can be associated with the larger lateral sizes characteristic of hexagonal columns in AlGaN layers grown by molecular beam epitaxy. No increase in the hole diffusion length is observed for thicker films.

36 MATERIALS SCIENCE↗

Schottky-Barrier Model Nonlinear in Surface-State Concentration and Calculation of the I–V Characteristics of Diodes Based on SiC and Its Solid Solutions in the Composite Charge-Transport Model

A modified Schottky-barrier model, which is nonlinear in terms of the surface-state concentration and contains a local quasi-Fermi level at the interface induced by excess surface charge, is proposed. Such an approach makes it possible to explain the observed similarity of the I–V characteristics of diodes with the Schottky barrier M/(SiC){sub 1–x}(AlN){sub x} and those of heterojunctions based on SiC and its solid solutions taking into account Φ{sub g} ≈ Φ{sub B}. The results of calculations of the Schottky-barrier heights are consistent with the experimental data obtained from measurements of the photocurrent for metals (M): Al, Ti, Cr, and Ni. The I–V characteristics in the composite–additive model of charge transport agree with the experimental data for the n-M/p-(SiC){sub 1–x}(AlN){sub x} and n-6H-SiC/p-(SiC){sub 0.85}(AlN){sub 0.15} systems.

36 MATERIALS SCIENCE↗

GaAs Wurtzite Nanowires for Hybrid Piezoelectric Solar Cells

The properties of the hybrid energy sources “piezoelectric nanogenerator-solar cell” based on GaAs nanowires with the wurtzite crystal structure were investigated. Measurements were performed by the bending of the nanowire by the probe of the atomic force microscope with simultaneous recording of short circuit current in dark and illuminated conditions. We show that a piezoelectric current pulse of ~10 pA arises in the “nanowire-probe” circuit during the deformation of nanowire by the AFM probe. Under laser illumination, the value of the pulse increases by two orders of magnitude as a result of the piezophototronic effect. Deformation of the nanowire boosts the photocurrent by 40% up to 0.5 nA.

36 MATERIALS SCIENCE↗

Photoconductivity Amplification in a Type-II n-GaSb/InAs/p-GaSb Heterostructure with a Single QW

Significant photocurrent/photoconductivity amplification is observed at low reverse biases in a type-II n-GaSb/InAs/p-GaSb heterostructure with a single quantum well (QW), grown by metal-organic vapor phase epitaxy. A sharp increase in the photocurrent by more than two orders of magnitude occurs under exposure of the heterostructure to monochromatic light with a wavelength of 1.2–1.6 μm (at 77 K) and the application of a reverse bias in the range 5–200 mV. The optical gain depends on the applied voltage and increases to 2.5 × 10{sup 2} at a reverse bias of 800 mV. Theoretical analysis demonstrated that the main role in the phenomenon is played by the screening of the external electric field by electrons accumulated in the deep InAs QW and by the mechanism of the tunneling transport of carriers with a small effective mass. It is shown that the effect under study is common to both isotype and anisotype type-II heterojunctions, including structures with QWs and superlattices.

36 MATERIALS SCIENCE↗

On the Fabrication of Graphene p–n Junctions and Their Application for Detecting Terahertz Radiation

A new method for the formation of lateral p–n junctions in epitaxial graphene with the use of UV (ultraviolet) radiation is considered. The UV illumination method makes it possible to obtain large-size p–n junctions. Such p–n junctions are investigated in the photocurrent and photoconductivity modes under irradiation with terahertz radiation. The mechanisms of terahertz photoresponse in graphene p–n junctions are discussed.

36 MATERIALS SCIENCE↗

Growth, Characterization, and Electrochemical Properties of Doped n-type KTaO3 Photoanodes

The effects of compositionally induced changes on the semiconducting properties, optical response, chemical stability, and overall performance of KTaO3 photo-anodes in photoelectrochemical cells have been investigated. Single crystals of n-type Ca- and Ba-doped KTaO3 with carrier concentrations ranging from 0.45 - 11.5 x 1019 cm-3 were grown and characterized as photoanodes for hydrogen production in basic aqueous electrolytes. The photoelectrochemical properties of the crystals, including the photocurrent, photovoltage, and flat-band potential in contact with 8.5 M NaOH(aq) were relatively independent of whether Ca or Ba was used to produce the semiconducting form of KTaO3. All of the Ca- or Ba- doped KTaO3 single crystal photoanodes were chemically stable in the electrolyte; and based on the open-circuit potential and the band-edge positions, they were capable of unassisted photochemical H2 and O2 evolution from H2O. The minority carrier diffusion lengths values were small and comparable to the depletion region width. Photoanodic currents were only observed for photo-anode illumination with light above the band gap (i.e., < 340 nm). The maximum external quantum yield occurred at = 1 nm (4.85 eV), and the depletion width plus the minority carrier diffusion length ranged from 20 to 65 nm for the various KTaO3-based photoanode materials.

08 HYDROGEN↗

Morphological Control of GaN and Its Effect within Electrochemical Heterojunctions

With morphological control through a solid source chemical vapor deposition process, GaN polycrystalline films, single-crystal nanowires, and mixed film/wires are grown on silicon to form a heterojunction that is a basis for III-V nitride device development. By contacting the GaN/Si structure to the CoCp 2 0/ + redox pair and performing impedance spectroscopy measurements, the band diagram of this junction is built for these three configurations. This serves as a basis for understanding the electrical nature of III-V nitride/Si interfaces that exist in several photonic device technologies, especially in context of using GaN nanomaterials grown on silicon for various applications. When these junctions are exposed to low-power UV illumination in contact with the Fc/Fc + redox pair, photocurrents of 18, 110, and 482 nA/cm 2 are generated for the nanowires, mixed film/wires, and films respectively. These currents, along with the electrostatics investigated through the impedance spectroscopy, show the trends of photoconversion with GaN morphology in this junction. Furthermore, they suggest that the mixed film/wires are a promising design for solar-based applications such as photovoltaics and water splitting electrodes.

25 ENERGY STORAGE↗

Electrochemical Reduction Properties of Extended Space Charge InGaP and GaP Epitaxial Layers

Two lattice-matched epitaxial III-V phosphide films of thicknesses between 400 and 500 nm are grown by metal-organic chemical vapor deposition: InGaP on GaAs and GaP on Si. These structures are designed as photocathodes for solar-driven chemical reduction processes such as the hydrogen evolution reaction (HER) and CO 2 reduction into higher-order hydrocarbons. By using p + substrates and undoped epitaxial layers, an extended space-charge active region is achieved in the electrode with a design analogous to a p-i-n solar cell. When in contact with the methyl viologen MV + / + + redox couple, the InGaP/GaAs and GaP/Si cathodes generate a photovoltage of 388 mV and 274 mV, respectively, under 1 sun illumination. Incident photon-to-current efficiency (IPCE) measurements confirm that the undoped active layers are exclusively performing light absorption and minority carrier diffusion-based charge transfer of high-energy photons. This shows that performance can be significantly boosted with lower-doped substrates. The InGaP/GaAs and GaP/Si electrodes are shown to drive the HER at saturation photocurrent densities of 9.05 mA/cm 2 and 2.34 mA/cm 2 , respectively, under 1 sun illumination without a co-catalyst and under a large reduction bias. As a result, thicker films did not show a corresponding increased performance, and can be explained through understanding of crystalline defects and the electrostatics of the junctions.

25 ENERGY STORAGE↗

Development of a switched integrator amplifier for high-accuracy optical measurements

In the field of low flux optical measurements, the development and use of large area silicon detectors is becoming more frequent. The current/voltage conversion of their photocurrent presents a set of problems for traditional transimpedance amplifiers. The switched integration principle overcomes these limitations. We describe the development of a fully characterized current-voltage amplifier using the switched integrator technique. Two distinct systems have been developed in parallel at the United Kingdom's National Physical Laboratory (NPL) and Czech Metrology Institute (CMI) laboratories. We present the circuit theory and best practice in the design and construction of switched integrators. In conclusion the results achieved and future developments are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Terahertz emission from a femtosecond laser focus in a two-color scheme

We critically revise the theory of terahertz emission from a plasma filament induced in a gas media by one or two focusd femtosecond laser pulses. We distinguish a radiation pressure force (RPF) from a ponderomotive force (PF), discuss conditions for one of these forces to be the dominating contribution to the terahertz emission, and also show that the angular distribution of the emitted power critically depends on which of the two forces dominates in a particular experiment. We show that the experimentally observed periodic dependence of the emitted terahertz power on the gas pressure reveals the dominating role of the RPF over the PF, whereas the angular diagram of the emission allows us to determine the predominant direction of the force. We also emphasize that the terahertz emission originated by a transient photocurrent exhibits a different dependency from the phase difference between the first and the second harmonics of the optic laser field, which generally enables the experimental detection of the prevailing mechanism of the terahertz emission from the plasma filament.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Si⁺-implanted Si-wire waveguide photodetectors for the mid-infrared

CMOS-compatible Si⁺-implanted Si-waveguide p-i-n photodetectors operating at room temperature and at mid-infrared wavelengths from 2.2 to 2.3 µm are demonstrated. Responsivities of 9.9 ± 2.0 mA/W are measured at a 5 V reverse bias with an estimated internal quantum efficiency of 2.7 – 4.5%. The dark current is found to vary from a few microamps down to less than a nanoamp after a post-implantation annealing of 350°C. The measured photocurrent dependence on input power shows a linear correspondence over more than three decades, and the frequency response of a 250 µm-length p-i-n device is measured to be ~1.7 GHz for a wavelength of λ = 2.2 µm, thus potentially opening up new communication bands for photonic integrated circuits.

42 ENGINEERING↗

Ultrathin planar hematite film for solar photoelectrochemical water splitting

Hematite holds promise for photoelectrochemical (PEC) water splitting due to its stability, low-cost, abundance and appropriate bandgap. However, it suffers from a mismatch between the hole diffusion length and light penetration length. We have theoretically designed and characterized an ultrathin planar hematite/silver nanohole array/silver substrate photoanode. Due to the supported destructive interference and surface plasmon resonance, photons are efficiently absorbed in an ultrathin hematite film. In conclusion, compared with ultrathin hematite photoanodes with nanophotonic structures, this photoanode has comparable photon absorption but with intrinsically lower recombination losses due to its planar structure and promises to exceed the state-of-the-art photocurrent of hematite photoanodes.

36 MATERIALS SCIENCE↗

Highly efficient terahertz photoconductive metasurface detectors operating at microwatt-level gate powers

Despite their wide use in terahertz (THz) research and technology, the application spectra of photoconductive antenna (PCA) THz detectors are severely limited due to the relatively high optical gating power requirement. This originates from poor conversion efficiency of optical gate beam photons to photocurrent in materials with sub-picosecond carrier lifetimes. Here we show that using an ultra-thin (160 nm), perfectly absorbing low-temperature grown GaAs metasurface as the photoconductive channel drastically improves the efficiency of THz PCA detectors. This is achieved through perfect absorption of the gate beam in a significantly reduced photoconductive volume, enabled by the metasurface. This Letter demonstrates that sensitive THz PCA detection is possible using optical gate powers as low as 5 µW—three orders of magnitude lower than gating powers used for conventional PCA detectors. We show that significantly higher optical gate powers are not necessary for optimal operation, as they do not improve the sensitivity to the THz field. This class of efficient PCA THz detectors opens doors for THz applications with low gate power requirements.

47 OTHER INSTRUMENTATION↗

Multiple-polarization-sensitive photodetector based on a perovskite metasurface

Most polarization-sensitive photodetectors detect either linearly polarized (LP) or circularly polarized (CP) light. Here, we experimentally demonstrate a multiple-polarization photodetector based on a hybrid organic–inorganic perovskite (HOIP) metasurface, which is sensitive to both LP and CP light simultaneously. The perovskite metasurface is composed of a HOIP antenna array on a single-crystal HOIP film. Owing to the antenna anisotropy, the absorption of linearly polarized light at the metasurface depends on the polarization angle; also, due to the mirror asymmetry of the antenna elements, the metasurface is also sensitive to different circular polarizations. Polarization-dependent photocurrent responses to both LP and CP light are detected. Our results highlight the potential of perovskite metasurfaces for integrated photoelectric applications.

47 OTHER INSTRUMENTATION↗