Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Parameter Identifiability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Composite interlaminar fracture toughness: Three-dimensional finite element modeling for mixed mode 1, 2 and 3 fracture

A computational method/procedure is described which can be used to simulate individual and mixed mode interlaminar fracture progression in fiber composite laminates. Different combinations of Modes 1, 2, and 3 fracture are simulated by varying the crack location through the specimen thickness and by selecting appropriate unsymmetric laminate configurations. The contribution of each fracture mode to strain energy release rate is determined by the local crack closure methods while the mixed mode is determined by global variables. The strain energy release rates are plotted versus extending crack length, where slow crack growth, stable crack growth, and rapid crack growth regions are easily identified. Graphical results are presented to illustrate the effectiveness and versatility of the computational simulation for: (1) evaluating mixed-mode interlaminar fracture, (2) for identifying respective dominant parameters, and (3) for selecting possible simple test methods.

Murthy, P. L. N.↗

Forward-bias tunneling - A limitation to bipolar device scaling

Forward-bias tunneling is observed in heavily doped p-n junctions of bipolar transistors. A simple phenomenological model suitable to incorporation in device codes is developed. The model identifies as key parameters the space-charge-region (SCR) thickness at zero bias and the reduced doping level at its edges which can both be obtained from CV characteristics. This tunneling mechanism may limit the maximum gain achievable from scaled bipolar devices.

Del Alamo, Jesus A.↗

Analysis of modeling errors in system identification

This paper is concerned with the identification of a system in the presence of several error sources. Following some basic definitions, the notion of 'near-equivalence in probability' is introduced using the concept of near-equivalence between a model and process. Necessary and sufficient conditions for the identifiability of system parameters are given. The effect of structural error on the parameter estimates for both deterministic and stochastic cases are considered.

Hadaegh, F. Y.↗

An experimental investigation of straight and curved annular wall jets

Accurate turbulence measurements taken in wall jet flows are difficult to obtain, due to high intensity turbulence and problems in achieving two-dimensionality. The problem is compounded when streamwise curvature of the flow is introduced, since the jet entrainment and turbulence levels are greatly increased over the equivalent planar values. In this experiment, two-dimensional straight and curved incompressible wall jet flows are simulated by having a jet blow axially over a cylinder. Hot wire measurements and some Laser Doppler Velocimetry measurements are presented for straight and curved wall jet flows. The results for the straight wall showed good agreement between the annular flow data and the rectangular data taken by previous researchers. For the jets with streamwise curvature, there was agreement between the annular and corresponding rectangular jets for the flow region closest to the slot exit. An integral analysis was used as a simple technique to interpret the experimental results. Integral momentum calculations were performed for both straight and curved annular and two dimensional wall jets. The results of the calculation were used to identify transverse curvature parameters and to predict the values of those parameters which would delineate the region where the annular flow can satisfactorily simulate two dimensional flow.

Rodman, L. C.↗

An approximation theory for the identification of nonlinear distributed parameter systems

An abstract approximation framework for the identification of nonlinear distributed parameter systems is developed. Inverse problems for nonlinear systems governed by strongly maximal monotone operators (satisfying a mild continuous dependence condition with respect to the unknown parameters to be identified) are treated. Convergence of Galerkin approximations and the corresponding solutions of finite dimensional approximating identification problems to a solution of the original finite dimensional identification problem is demonstrated using the theory of nonlinear evolution systems and a nonlinear analog of the Trotter-Kato approximation result for semigroups of bounded linear operators. The nonlinear theory developed here is shown to subsume an existing linear theory as a special case. It is also shown to be applicable to a broad class of nonlinear elliptic operators and the corresponding nonlinear parabolic partial differential equations to which they lead. An application of the theory to a quasilinear model for heat conduction or mass transfer is discussed.

Banks, H. T.↗

Apparent brightness of stars and lasers

Foremost among issues affecting the potential use of astrometric techniques to locate and track laser-carrying spacecraft is the apparent brightness of a laser relative to reference stars. Broadband detectors offer improved sensitivity to stars, but not to lasers. The important and fundamental step of calibrating laser and star brightnesses according to detector spectral sensitivity is performed for four representative kinds of broadband detectors, located above and below the atmosphere. Stars are identified according to parameters traditionally used by astronomers: temperature and apparent brightness at visible wavelengths. These are translated into an energy and photon flux for each kind of broadband detector and are then compared with the corresponding flux from a laser. The comparisons are also given as magnitude correction factors. Astrometrists typically characterize the sensitivity of their instruments in terms of the precision with which they can make a relative measurement of position and the minimum brightness needed to achieve that precision. Given this information and the instruments's spectral sensitivity, the calculations described can be used to infer the detectability of a laser and the precision with which it could be located and tracked. Since the limiting brightness quoted for a particular instrument is typically firm to within 4.0 dB, judging a laser's detectability by its visible brightness alone could lead to serious underestimation of the requirements on its effective radiated power. The laser brightness corrections given solve this problem.

Schumaker, B. L.↗

The design analysis of a rechargeable lithium cell for space applications

Ambient temperature rechargeable lithium batteries are needed by NASA for advanced space power applications for future missions. Specific energies of not less than 100 Wh/kg and long cycle life are critical performance goals. A design analysis of a 35 Ah Li-TiS2 cell was carried out using literature and experimental data to identify key design parameters governing specific energy. It is found that high specific energies are achievable in prismatic cells, especially with the use of advanced hardware materials. There is a serious need for a greatly expanded engineering database in order to enable more quantitative design analysis.

Subba Rao, S.↗

Analysis of kink band formation under compression

The kink band formation in unidirectional composites under compression is analyzed in the present paper. The kinematics of kink band formation is described in terms of a deformation tensor. Equilibrium conditions are then applied to relate the compression load to the deformation of fibers. Since the in situ shear behavior of the matrix resin is not known, an analysis-experiment correlation is used to find the shear failure strain in the kink band. The present analysis thus elucidates the mechanisms and identifies the controlling parameters, of compression failure.

Hahn, H. Thomas↗

Application of unsteady aeroelastic analysis techniques on the national aerospace plane

A presentation provided at the Fourth National Aerospace Plane Technology Symposium held in Monterey, California, in February 1988 is discussed. The objective is to provide current results of ongoing investigations to develop a methodology for predicting the aerothermoelastic characteristics of NASP-type (hypersonic) flight vehicles. Several existing subsonic and supersonic unsteady aerodynamic codes applicable to the hypersonic class of flight vehicles that are generally available to the aerospace industry are described. These codes were evaluated by comparing calculated results with measured wind-tunnel aeroelastic data. The agreement was quite good in the subsonic speed range but showed mixed agreement in the supersonic range. In addition, a future endeavor to extend the aeroelastic analysis capability to hypersonic speeds is outlined. An investigation to identify the critical parameters affecting the aeroelastic characteristics of a hypersonic vehicle, to define and understand the various flutter mechanisms, and to develop trends for the important parameters using a simplified finite element model of the vehicle is summarized. This study showed the value of performing inexpensive and timely aeroelastic wind-tunnel tests to expand the experimental data base required for code validation using simple to complex models that are representative of the NASP configurations and root boundary conditions are discussed.

Pototzky, Anthony S.↗

Factors influencing elastic stresses in double cantilever beam specimens

An elastic stress analysis was conducted for a double cantilever beam (DCB) specimen using finite-element methods. The purpose of this study was to identify the important parameters that influence stresses ahead of the delamination front. The study focused on an aluminum DCB specimen, typical of adhesively-bonded joints, and on a graphite/epoxy specimen representing a cocured composite. Opening mode sigma sub y stresses ahead of the crack tip were calculated and compared with those for a monolithic reference specimen. Beyond the singularity-dominated region very near the crack tip, the sigma sub y distribution was elevated compared to the monolithic case. Both the adhesive thickness and the adherend transverse (thickness-direction) stiffness were found to influence the elevation of sigma sub y. In contrast, adherend thickness and longitudinal stiffness has very little effect on this stress distribution. Estimates for adhesive yielding beyond the aluminum DCB crack tip showed that both the area and height of the plastic zone increased to a peak value for increasing adhesive thicknesses. Results from this study would provide insight for comparing data from different DCB specimens and for designing new DCB specimens.

Crews, J. H., Jr.↗

Composite interlaminar fracture toughness - Three-dimensional finite-element modeling for mixed mode I, II, and fracture

A computational method/procedure is described which can be used to simulate individual and mixed mode interlaminar fracture progression in fiber composite laminates. Different combinations of Modes 1, 2, and 3 fracture are simulated by varying the crack location through the specimen thickness and by selecting appropriate unsymmetric laminate configurations. The contribution of each fracture mode to strain energy release rate is determined by the local crack closure methods while the mixed mode is determined by global variables. The strain energy release rates are plotted versus extending crack length, where slow crack growth, stable crack growth, and rapid crack growth regions are easily identified. Graphical results are presented to illustrate the effectiveness and versatility of the computational simulation for: (1) evaluating mixed-mode interlaminar fracture, (2) for identifying respective dominant parameters, and (3) for selecting possible simple test methods.

Murthy, Pappu L. N.↗

A detailed model of electrothermal propulsion systems

A semi-empirical model is presented which describes the operating characteristics of resistojet and arcjet engines. Propellants considered include hydrogen, ammonia and hydrazine. Specific engine design and performance correlations are derived from previously published contractor reports, conference and journal papers of the past three decades. Fundamental performance relationships are identified and correlating parameters derived to describe engine operation over a wide range of input powers and propellant mass flow rates. Outputs are presented from a computer program formulated using these modeling relationships. Comparisons are made with present electrothermal engine designs and examples are presented to illustrate the usefulness of the models in predicting engine operation as a function of changes in engine geometry and operating modes.

Aston, Graeme↗

Experimental investigation of straight and curved annular wall jets

Accurate turbulence measurements taken in wall jet flows are difficult to obtain, due to high intensity turbulence and problems in achieving two-dimensionality. The problem is compounded when streamwise curvature of the flow is introduced, since the jet entrainment and turbulence levels are greatly increased over the equivalent planar values. In this experiment, two-dimensional straight and curved incompressible wall jet flows are simulated by having a jet blow axially over a cylinder. Hot wire measurements and some Laser Doppler Velocimetry measurements are presented for straight and curved wall jet flows. The results for the straight wall showed good agreement between the annular flow data and the rectangular data taken by previous researchers. For the jets with streamwise curvature, there was agreement between the annular and corresponding rectangular jets for the flow region closest to the slot exit. An integral analysis was used as a simple technique to interpret the experimental results. Integral momentum calculations were performed for both straight and curved annular and two-dimensional wall jets. The results of the calculation were used to identify transverse curvature parameters and to predict the values of those parameters which would delineate the region where the annular flow can satisfactorily simulate two-dimensional flows.

Rodman, L. C.↗

Fuel-air mixing and distribution in a direct-injection stratified-charge rotary engine

A three-dimensional model for flows and combustion in reciprocating and rotary engines is applied to a direct-injection stratified-charge rotary engine to identify the main parameters that control its burning rate. It is concluded that the orientation of the six sprays of the main injector with respect to the air stream is important to enhance vaporization and the production of flammable mixture. In particular, no spray should be in the wake of any other spray. It was predicted that if such a condition is respected, the indicated efficiency would increase by some 6 percent at higher loads and 2 percent at lower loads. The computations led to the design of a new injector tip that has since yielded slightly better efficiency gains than predicted.

Abraham, J.↗

A gyroscope calibration analysis for the Gamma Ray Observatory (GRO)

Current documentation and software do not adequately address the calculation and use of the optimal weight matrices involved in calibrating inertial reference units (IRU). Several facets of the GRO IRU calibration as it relates to the bias and misalignment weighting matrices are investigated. The physical meaning and use of the bias and misalignment weight matrices in IRU calibration are examined. The relation of the weighting and the final biases, misalignments, and their corrections are pursued. Methods for determining reliable, realistic weighting matrices to be used in the GRO IRU calibration (IRUCAL) utility are determined. Possible correlations among observation uncertainties are also explored. For the undetermined case where the maneuvers are insufficient to identify all calibration parameters, the weighting matrices allow as much information as possible to be extracted from the measurements. Finally, applicable simulated flight data are used, incorporating the appropriate calibration maneuvers, to test the weighting matrices in the IRUCAL utility, and examine correlation effects.

Ketchum, Eleanor A.↗

An approximation theory for the identification of nonlinear distributed parameter systems

An abstract approximation framework for the identification of nonlinear distributed parameter systems is developed. Inverse problems for nonlinear systems governed by strongly maximal monotone operators (satisfying a mild continuous dependence condition with respect to the unknown parameters to be identified) are treated. Convergence of Galerkin approximations and the corresponding solutions of finite dimensional approximating identification problems to a solution of the original finite dimensional identification problem is demonstrated using the theory of nonlinear evolution systems and a nonlinear analog of the Trotter-Kato appproximation result for semigroups of bounded linear operators. The nonlinear theory developed here is shown to subsume an existing linear theory as a special case. It is also shown to be applicable to a broad class of nonlinear elliptic operators and the corresponding nonlinear parabolic partial differential equations to which they lead. An application of the theory to a quasilinear model for heat conduction or mass transfer is discussed.

Banks, H. T.↗

Nondimensional forms for singular perturbation analyses of aircraft energy climbs

This paper proposes a systematic approach for identifying the perturbation parameter in singular perturbation analysis of aircraft optimal guidance, and in particular considers a family of problems related to aircraft energy climbs. The approach, which is based on a nondimensionalization of the equations of motion, is used to evaluatae the appropriateness of forced singular perturbation formulations used in the past for transport and fighter aircraft, and to assess the applicability of energy state approximations and singular perturbation analysis for airbreathing transatmospheric vehicles with hypersonic cruise and orbital capabilities.

Calise, A. J.↗

Robust Kalman filter design for predictive wind shear detection

Severe, low-altitude wind shear is a threat to aviation safety. Airborne sensors under development measure the radial component of wind along a line directly in front of an aircraft. In this paper, optimal estimation theory is used to define a detection algorithm to warn of hazardous wind shear from these sensors. To achieve robustness, a wind shear detection algorithm must distinguish threatening wind shear from less hazardous gustiness, despite variations in wind shear structure. This paper presents statistical analysis methods to refine wind shear detection algorithm robustness. Computational methods predict the ability to warn of severe wind shear and avoid false warning. Comparative capability of the detection algorithm as a function of its design parameters is determined, identifying designs that provide robust detection of severe wind shear.

Stratton, Alexander D.↗