SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Procedures used to study the alpha to gamma conversion in thin foils of an iron alloy with 32% nickel concentration and initial martensite conversion temperature of -60 C are described. Photomicrographs show deformation twinning as well as changes in samples after they were heated. Reverse conversion is discussed and results are examined.
The fracture surfaces of compact tension specimens from seven nickel-base superalloys fatigue tested at 650 C were studied by scanning electron microscopy and optical metallography to determine the nature and morphology of the crack surface in the region of stable growth. Crack propagation testing was performed as part of an earlier study at 650 C in air using a 0.33 Hz fatigue cycle and a creep-fatigue cycle incorporating a 900 second dwell at maximum load. In fatigue, alloys with a grain size greater than 20 micrometers, HIP Astroloy, Waspaloy, and MERL 76, exhibited transgranular fracture. MERL 76 also displayed numerous fracture sites which were associated with boundaries of prior powder particles. The two high strength, fine grain alloys, IN 100 and NASA IIB-7, exhibited intergranular fracture. Rene 95 and HIP plus forged Astroloy displayed a mixed failure mode that was transgranular in the coarse grains and intergranular in the fine grains. Under creep-fatigue conditions, fracture was found to be predominantly intergranular in all seven alloys.
A study of the high-temperature oxidation and Na2SO4-induced hot corrosion of nickel-base superalloys has been accomplished by using ESCA to determine the surface composition of the oxidized or corroded samples. Oxidation was carried out at 900 or 1000 C in slowly flowing O2 for samples of B-1900, NASA-TRW VIA, 713C, and IN-738. Hot corrosion of B-1900 was induced by applying a coating of Na2SO4 to preoxidized samples, then heating to 900 C in slowly flowing O2. For oxidized samples, the predominant type of scale formed by each superalloy showed a marked surface enrichment of Ti. For corroded samples, the transfer of significant amounts of material from the oxide layer to the surface of the salt layer was observed before the onset of rapidly accelerating weight gain. Marked changes in surface composition coincided with the beginning of accelerating corrosion, the most striking of which were a tenfold decrease in the sulfur to sodium ratio and an increase in the Cr(VI) to Cr(III) ratio.
Magnetic properties of small iron-nickel alloy spheres, having compositions which cover the entire Fe-Ni binary, are presented. The spheres were formed during solidification in free fall following the melting of electropolished wires of appropriate composition. The spheres with Ni not greater than 25% acquired a martensitic thermal remanence while those with Ni not less than 30% acquired a thermoremanent magnetization. A magnetic remanence-composition diagram and a coercive force-composition diagram are constructed. Magnetic hysteresis loops and derived parameters demonstrate the difference between metal-bearing and oxide-bearing natural samples. The magnetic remanence varies as the sphere size in conjunction with the microstructure. These results help to explain why coercive force is generally low, remanent coercive force is generally high, and their ratio (R/C) is always large in fine metal dispersions, such as lunar samples and chondrite meteorites.
The chemisorption of gases on well-defined, supported metal particles is a model for basic processes in heterogeneous catalysis. In this study, the chemisorption and decomposition of carbon monoxide on palladium and nickel particles was examined as a function of particle size. Particulate films with average particle sizes ranging from 1 to 10 nm were grown by vapor deposition on UHV-cleaved mica. Successive CO adsorption-desorption cycles resulted in the accumulation of carbon on the particles, which suppressed CO adsorption. The rate of carbon accumulation was strongly dependent on particle size and was higher for Ni than for Pd over the same size range. Carbon was removed from both metals by oxygen treatments at elevated temperatures. However, a mixture of CO and O2 was effective for monitoring the removal of carbon from palladium.
The potential time characteristics of a preconditioned fully charged cell discharge at constant current was studied. Electrochemical principles applied to the sealed nickel cadmium cell and its behavior and to predict operating characteristics were described. A thermodynamic approach to arrive at several related but different equations and its discharge are reported.
Methods for determining the stacking fault energies of a series of nickel-copper alloys to gain an insight into the embrittling effect of hydrogen are evaluated. Plans for employing weak beam dark field electron microscopy to determine stacking fault energies are outlined.
Test results from continuous synchronous orbit testing of sealed nickel cadmium cells are presented. The synchronous orbit regime simulates a space satellite maintaining a position over a fixed point on earth as the earth rotates on its axis and revolves about the sun. Characteristics of each lot of cells, test conditions, and charge control methods are described.
The NASA standard 20 ampere hour spacecraft nickel-cadmium battery in described. Mechanical electrical and thermal data are supplied. Both qualification and acceptance tests are described. Information on handling and storage is given.
A systematic investigation of the effect of temperature and two conditions of storage, shortened and open circuit, on the capacity fading of sintered nickel electrodes in NiCd batteries was conducted. All testing was done on sintered electrodes in flooded cells. Cycling tests to measure the capacity were performed at room temperature. The capacity out to one volt, a capacity useful for satellite applications. Test results indicated that: the shortened electrode showed a higher rate of loss than the open circuit electrodes; there was an increase in both modes with an increase in temperature; there was a loss of capacity with time of storage; a general degradation was observed as a function of time; shortened electrodes showed a higher end of charge than the open circuit ones; and at room temperature there was a lower loss in the open circuit electrode than in the shortened one.
Some of the operational characteristics of some nickel hydrogen cells are explained. Some strange capacity excursions with cycling were seen.
A relay used on a standard flight configuration of nickel-hydrogen cells is discussed.
The electrochemical positive electrode was used in nickel hydrogen for six or seven years with very good results, primarily because of the dimensional stability and the high electrical utilization of the active material.
Linear-combination-of-Gaussian-type-orbital (LCGTO) X-alpha calculations are performed on NiCO for various linear Ni-CO and NiC-O bond distances. The basis sets used are moderately large, approximately double zeta, and thus are fairly accurate within the X-alpha approximation. The electronic structure and equilibrium bond distances are consistent with recent CI calculations, indicating a much stronger Ni-CO bond than occurs in Ni(CO)4. The calculations agree to within 100/cm with the experimentally observed NiC-O stretch frequency. The Ni-CO stretch is predicted to occur at 656/cm, although at an intensity that is 640 times less. Compared with experimental results for CO adsorbed on single crystal Ni(100), the computed vibrational frequencies and intensities are less appropriate than the relevant experimental values for Ni(CO)4. This is interpreted to mean that an accurate description of the electronic structure of the nickel atom participating directly in the surface bond requires proper accounting of the bonds to its other nearest neighbors.
Screenable thick film solar cell electrodes are made using the all-metal electrode system, which eliminates the commonly used glass frit and substitutes an oxide scavenger such as silver fluoride. The low temperature firing copper metal systems give good results on solar cells obtaining cell efficiencies of 13% AM1, and adhering sintered structures are demonstrated with nickel systems. The potential effect of copper upon cell performance at elevated temperatures over long periods of time is determined, and it is found that the formation of a copper-silicon eutectic at 550 C produces needle-like structures with broad bases on the silicon, extending into and occasionally through the metallization layer.
Results obtained from a balloon exposure of a cosmic ray detector flown in 1977 are reported. The charge resolution ranged from 0.19 to 0.21 charge units between neon and nickel and the mass resolution for nuclei stopped in the emulsions ranged from 0.40 to 0.70 amu for A between 20 and 60 amu. This was enough to correctly identify almost all nuclei, but not to uniquely resolve neighboring mass peaks. Both Ne and Mg show evidence for neutron enrichment relative to the solar system abundance. Si and S are consistent with solar abundances, while Ar has no significant source abundances. P, Cl and K have essentially no primary component and the isotopic distribution observed is quite consistent with that expected from propagation. An excess of Ca-44 at the source is shown, indicating high metallicity in the source. The abundance of Fe-58 is nine percent or less, and Ni shows a one-to-one ratio for Ni-58 to 60, implying intermediate metallicity.
Transmission electron microscopy has been used to study the bulk deformation characteristics of seven nickel-base superalloys tested in fatigue and creep-fatigue at 650 C. The alloys were Waspalloy, HIP Astroloy, H plus F Astroloy, H plus F Rene 95, IN 100, MERL 76, and NASA IIB-7. The amount of bulk deformation observed in all the alloys was low. In tests with inelastic strain amplitudes less than about 0.003, only some grains exhibited yielding and the majority of those had the 110 line near the tensile axis. Deformation occurred on octahedral systems for all of the alloys except MERL 76 which also showed abundant primary cube slip. Creep-fatigue cycling occasionally produced extended faults between partial dislocations, but otherwise deformation was much the same as for fatigue cycling.
Experiments in intergranular cracking of nickel alloy near solidus temperature discussed in contractor report. Purpose of investigation development of schedule for welding, casting, forging, or other processing of alloy without causing microfissuring.