Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Materials for Devices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Modifications in the charge trap landscape in Hf 0.5 Zr 0.5 O 2 as a function of oxygen vacancy concentration observed with photoemission electron microscopy

Oxygen vacancies in Hf x Zr (1-x) O 2 (HZO) both contribute to stabilization of the ferroelectric orthorhombic phase and promote leakage pathways that limit the endurance of devices based on the material. Here, for this reason, the defect states of oxygen vacancies were investigated using photoemission electron microscopy (PEEM) and photoluminescence spectroscopy (PL), as their concentration was varied via ex situ laser exposure. Following a controlled oxygen vacancy reduction via visible (2.54 eV) laser dosing of HZO, deep-ultraviolet (DUV, 5.82 eV) PEEM was used to spatially probe the resulting mid-gap defect states and work function. Work function was found to increase monotonically with the laser-induced reduction in oxygen vacancy concentration culminating in a total increase near 70 meV. The change implies a Fermi level shift toward the valence band as the total available electron-filled charge states are reduced with the removal of oxygen vacancies. A reduction in charge states is corroborated by the observed lessening of both photoemission and photoluminescence intensities after laser dosing. The deduced position of the Fermi level is within a band of near-conduction band defect states produced by oxygen vacancies that are linked to endurance limiting leakage currents. Together, these results directly identify the primary role of oxygen vacancies on the defect states in HZO while demonstrating that laser exposure can be used for their modification.

42 ENGINEERING↗
DOE OSTI2025

Nanometer-thick ultraflat cantilever resonators

Nanomechanical devices made from ultrathin materials are transforming diverse fields, including sensing, signal processing, and quantum technologies. However, as these materials become thinner, their low bending rigidity poses significant fabrication challenges, and achieving nanometer-thick flat cantilevers with consistent and predictable mechanical responses has remained elusive despite decades of research. Here we present nanometer-thick, ultraflat cantilever resonators fabricated using atomic layer deposition. By effectively mitigating the effects of uncontrollable built-in strain and geometric disorder, the ultraflat nanocantilevers exhibit resonance frequencies closely aligned with thin-plate theory predictions and display low sample-to-sample variability. These cantilevers maintain mechanical stability in both vacuum and air environments, even at large length-to-thickness ratios of up to 3000. The ultraflat nanocantilevers are approaching the thickness limit, beyond which thermal fluctuations at room temperature can spontaneously induce random ripples in otherwise flat films.

nanofabrication↗
DOE OSTI2023

Physical and technical basis of Materials Plasma Exposure eXperiment from modeling and Proto-MPEX results *

Abstract The Materials Plasma Exposure eXperiment (MPEX) is a steady-state linear plasma device that will address plasma-material interaction (PMI) science and enable testing of fusion reactor-relevant divertor plasma-facing materials. The MPEX source concept consists of a helicon plasma source to generate the plasma, electron cyclotron heating (ECH) for electron heating, and ion cyclotron heating (ICH) for ion heating. The MPEX source plasma is then transported axially to the PMI material target region to test material samples in fusion reactor-relevant divertor conditions. This paper will summarize the physical and technical basis of MPEX. The paper will first define the MPEX parameters and scenarios at the target relevant to PMI science for various fusion reactor-relevant divertor conditions and show plasma transport modeling results to set the MPEX source parameters. Recent experimental and modeling results from Proto-MPEX, a short-pulse experiment to develop the plasma production, heating, and transport physics for MPEX, will be shown. From these results, it will be shown that MPEX can reach its desired scenarios. The MPEX physical and technical basis will also determine important functional requirements for magnetic field, radiofrequency (RF) power, RF frequency, and neutral pressure in the helicon, ECH, ICH, and PMI regions that are required to achieve the desired MPEX scenarios. The necessity for key in-vessel components such as skimmers, limiters, and microwave absorbers will also be highlighted.

Lau, C. (ORCID:0000000285765867)↗
DOE OSTI2022

Phoebe: a high-performance framework for solving phonon and electron Boltzmann transport equations

Understanding the electrical and thermal transport properties of materials is critical to the design of electronics, sensors, and energy conversion devices. Computational modeling can accurately predict material properties but, in order to be reliable, requires accurate descriptions of electron and phonon states and their interactions. While first-principles methods are capable of describing the energy spectrum of each carrier, using them to compute transport properties is still a formidable task, both computationally demanding and memory intensive, requiring integration of fine microscopic scattering details for estimation of macroscopic transport properties. To address this challenge, we present Phoebe—a newly developed software package that includes the effects of electron–phonon, phonon–phonon, boundary, and isotope scattering in computations of electrical and thermal transport properties of materials with a variety of available methods and approximations. This open source C++ code combines MPI-OpenMP hybrid parallelization with GPU acceleration and distributed memory structures to manage computational cost, allowing Phoebe to effectively take advantage of contemporary computing infrastructures. We demonstrate that Phoebe accurately and efficiently predicts a wide range of transport properties, opening avenues for accelerated computational analysis of complex crystals.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Refining the two-band model for highly compensated semimetals using thermoelectric coefficients

In studying compensated semimetals, the two-band model has proven extremely useful in capturing electrical conductivity under magnetic field, as a function of density and mobility of electronlike and holelike carriers. However, it rarely offers practical insight into magnetothermoelectric properties. Here, in this work, we report the field dependence of thermoelectric (TE) coefficients in a highly compensated semimetal NbSb 2 , where we find the Seebeck (𝑆 𝑥⁢𝑥 ) and Nernst (𝑆 𝑥⁢𝑦 ) coefficients increase quadratically and linearly with applied magnetic field, respectively. Such field dependence was predicted in previous work that studied a system of two parabolic bands, within semiclassical Boltzmann transport theory when the following two conditions are simultaneously met: 𝜔 𝑐 ⁢𝜏 ≫ 1 and tan ⁡𝜃 𝐻 ≪ 1, where 𝜔 𝑐 and 𝜏 refer to the cyclotron frequency and relaxation time, respectively, and 𝜃 𝐻 is the Hall angle. Under these conditions, we find the field dependence of the TE coefficients directly provides a relation between the electronlike (𝑛 𝑒 ) and holelike (𝑛 ℎ ) carrier densities, which in turn can be used to refine two-band model fitting. With this, we find the compensation factor ($\frac{|Δ⁢𝑛|}{𝑛_{𝑒}}$, where Δ⁢𝑛 = 𝑛 𝑒 −𝑛 ℎ ) of NbSb 2 is two orders of magnitude smaller than what was found in unrestricted fitting, resulting in a larger saturation-field scale for magnetoresistance. Within the same framework of the semiclassical theory, we also deduce that the thermoelectric Hall angle tan⁡ 𝜃 𝛾 = $\frac{𝑆_{𝑥⁢𝑦}}{𝑆_{𝑥⁢𝑥}}$ can be expressed as ($\frac{Δ⁢𝑛}{𝑛_{𝑒}}$ ×𝜔 𝑐 ⁢𝜏) −1 , which serves as a parameter to predict the degree of compensation. Our findings offer crucial insights into identifying empirical conditions for field-induced enhancement of TE performance and into engineering-efficient thermoelectric devices based on semimetallic materials.

electrical conductivity↗
DOE OSTI2023

Vortex dynamics induced by scanning SQUID susceptometry

In this work, we measured the local magnetic response of a niobium thin film by applying a millitesla-scale AC magnetic field using a micron-scale field coil and detecting the response with a micron-scale pickup loop in a scanning superconducting quantum interference device (SQUID) susceptometry measurement. Near the film's critical temperature, we observed a steplike nonlinear and dissipative magnetic response due to the dynamics of a small number of vortex-antivortex pairs induced in the film by the local applied AC field. We modeled the dynamics of the measurement using a combined two-dimensional London-Maxwell and time-dependent Ginzburg-Landau approach, allowing us to construct a detailed real-space picture of the vortex motion causing the observed dissipative response. This work pushes scanning SQUID susceptometry of two-dimensional superconductors beyond the regime of linear response and lays the foundation for microscopic studies of vortex dynamics and pinning in superconducting devices and more exotic materials systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Magnetostriction and temperature dependent Gilbert damping in boron doped Fe 80 ⁢Ga 20 thin films

Magnetic thin films with strong magnetoelastic coupling and low Gilbert damping are key materials for many magnetoelectric devices. Here, we investigated the effects of boron doping concentration on magnetostriction and temperature dependent Gilbert damping in magnetron sputtered (Fe 80 ⁢Ga 20 ) 1−𝑥 ⁢B 𝑥 films. A crystalline to amorphous structural transition was observed for a boron content near 8% and coincided with a decrease in coercivity from 76 Oe to 3 Oe. A 10% doping concentration is optimal for achieving both large magnetostriction of 48.8 ppm and low Gilbert damping of 6×10 −3 . The temperature dependence of the damping shows an increase at low temperatures with a peak around 40 K, and we associate the relative increase Δ⁢𝛼/𝛼 RT with magnetoelastic contributions to the damping, which has a maximum of 55.7% at 8% boron. An increase in the inhomogeneous linewidth broadening was observed in the structural transition regime at about 8% boron concentration. Furthermore, this study suggests that incorporation of glass forming elements, in this case boron, into Fe 80 ⁢Ga 20 is a practical pathway for simultaneously achieving enhanced magnetoelastic coupling and reduced Gilbert damping.

Cryogenics↗
DOE OSTI2022

Irradiation-induced Degradation of Surface Acoustic Wave Devices Fabricated on Bulk AlN

Here, recent work to evaluate the prospects for surface acoustic wave (SAW) devices fabricated on bulk aluminum nitride (AlN) for elevated temperature and radiation environments is reported and discussed. The design and fabrication of an array of SAW devices using commercial wafers is described, including the non-standard fabrication approach taken to overcome the stress-induced warpage of the 50 mm diameter AlN substrates. Radio frequency performance characterization of the SAW devices, with resonance frequencies ranging from 0.5 GHz to 1.5 GHz, is described. The linear temperature coefficient of frequency (TCF) near room temperature was measured and is compared to theoretical results from other investigators. Further, the effects of 8 MeV Al ion irradiation at 300°C and 500°C to damage levels of 0.01, 0.1 and 1 displacements per atom (dpa), as a proxy for neutron irradiation, was investigated. The ion irradiation damage was observed to decrease the SAW resonant frequency, and this effect is characterized and discussed. Significant degradation in the conductivity of the Ti/Al electrodes of the SAW devices was also observed and characterized. These experimental results provide a basis for further investigation of the prospects for development of SAW sensor devices in bulk AlN material for application in elevated temperature and radiation environments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Numerical Simulation of Container Breach and Airborne Release of Solids Due to Mechanical Insults

Throughout U.S. Department of Energy (DOE) complexes, safety engineers employ the five-factor formula to calculate the source term (ST) that includes parameters of airborne release fraction (ARF), respirable fraction (RF) and damage ratio (DR). Limited experimental data on fragmentation of solids, such as ceramic pellets (i.e., PuO2), and container breach due to mechanical insults (i.e., drop and forklift impact), can be supplemented by modeling and simulation using high fidelity computational tools to estimate these parameters. This paper presents the use of Sandia National Laboratories' SIERRA solid mechanics (SM) finite element code to investigate the behavior of the widely utilized waste container (such as 7A Drum) subject to a range of free fall impact and puncture scenarios. The resulting behavior of the container is assessed, and the estimates are presented for bounding DRs from calculated breach areas for the various accident conditions considered. This paper also describes a novel multiscale constitutive model recently implemented in SIERRA/SM that simulates the fracture of brittle materials such as PuO 2 and determines ARF during the fracture process. Furthermore, comparisons are made between model predictions and simple bench-top experiments.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2021

Photothermal alternative to device fabrication using atomic precision advanced manufacturing techniques

The attachment of dopant precursor molecules to depassivated areas of hydrogen-terminated silicon templated with a scanning tunneling microscope (STM) has been used to create electronic devices with subnanometer precision, typically for quantum physics experiments. This process, which we call atomic precision advanced manufacturing (APAM), dopes silicon beyond the solid-solubility limit and produces electrical and optical characteristics that may also be useful for microelectronic and plasmonic applications. However, scanned probe lithography lacks the throughput required to develop more sophisticated applications. In this work, we demonstrate and characterize an APAM device workflow where scanned probe lithography of the atomic layer resist has been replaced by photolithography. An ultraviolet laser is shown to locally and controllably heat silicon above the temperature required for hydrogen depassivation on a nanosecond timescale, a process resistant to under- and overexposure. STM images indicate a narrow range of energy density where the surface is both depassivated and undamaged. Modeling that accounts for photothermal heating and the subsequent hydrogen desorption kinetics suggests that the silicon surface temperatures reached in our patterning process exceed those required for hydrogen removal in temperature-programmed desorption experiments. A phosphorus-doped van der Pauw structure made by sequentially photodepassivating a predefined area and then exposing it to phosphine is found to have a similar mobility and higher carrier density compared with devices patterned by STM. Lastly, it is also demonstrated that photodepassivation and precursor exposure steps may be performed concomitantly, a potential route to enabling APAM outside of ultrahigh vacuum.

nanoscale devices↗
DOE OSTI2021

Application of machine learning to estimate fireball characteristics and their uncertainty from infrared spectral data

Experiments or events involving high explosives (HE) can be monitored remotely by infrared (IR) sensors to gather information about the configuration or materials involved in the device. Researchers at the Air Force Institute of Technology (AFIT) developed a phenomenological model for HE fireball spectra in the IR range that allows for parameters to be extracted from Fourier transform infrared (FTIR) data. This model includes parameters tied to physical characteristics of the fireball: temperature, size, soot, and gas concentrations. Previous works have sought to recover these parameters by the fitting of either whole spectra or select wavenumber bands to this phenomenological model. Difficulties arise due to the complex relationships between the parameters to be fit. Uncertainty quantification of the estimated fireball parameters is also problematic since HE experiments do not have any ground truth information on the parameters. It is suggested that artificial neural network (ANN) based approaches may be well suited to this problem, because of their ability to capture complex and highly nonlinear relationships. As such, this work seeks to explore the efficacy of deep artificial neural networks (DNNs) for this problem of parameter recovery from spectra and to also investigate the uncertainty of recovering the fireball parameters from FTIR data. Networks are designed using the hyperparameter optimization tool Hyperopt and trained/tested on artificial data generated using the phenomenological model developed by AFIT. The results of applying the network to the artificial data set are compared to a physics-based band approach that uses a selected number of bands based on their physical properties. Information on the uncertainty of estimating parameters from remotely sensed experimental data is obtained by treating the accuracy of the DNN model on artificial data as an upper bound and by examining the impact of emissivity due to soot on parameter estimation error; the results for artificial data are likely to be optimistic as compared to recovering parameters from experimental data.

42 ENGINEERING↗
DOE OSTI2020

Random Forest Optimization for Radionuclide Identification

Radionuclide identification through gamma-ray spectroscopy is an indispensable tool in combatting the illicit smuggling of nuclear material. The radionuclide identification devices used in the field need to provide ready-made answers to non-experts, and therefore require sophisticated algorithms that can interpret the underlying data. We investigated the Random Forest classifier as a tool for identifying the radionuclide that is consistent with the data. We were provided with training and validations data sets and used them to optimize the two hyperparameters of the classifiers: maximum features required, and minimum samples used to split each node. The F1 score, a harmonic mean of precision and recall, was used to evaluate the performance of each built classifier. We found the optimal performance with minimum samples of 5 and maximum features of 50, with the F1 score of 0.95.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2023

Composite Cathode Architectures Made By Freeze-Casting for All Solid State Lithium Batteries (CRADA Final Report)

As part of a Battery 500 seedling project, MBRDNA partnered with LBNL and Montana State University (MSU) to develop solid-state batteries based on an Al-substituted LLZO (Li 7 La 3 Zr 2 O 12 ) ceramic ion-conductor. All solid-state lithium batteries are attractive contenders for use as power sources for electric vehicles because of their potential for better safety and higher energy density than state-of-the-art lithium-ion batteries, although they are still at early stages of development. Al-substituted LLZO is one of the most promising solid electrolytes for battery applications based on high ionic conductivity, a wide operating voltage window, and apparent stability vs. reduction by lithium. However, difficulties with processing thin (< 20 $\textit{um}$ and dense LLZO membranes have hampered development of devices based on this material. It is non-compressible and must be sintered at high temperatures to densify components. It is also difficult to maintain contact between the active cathode material and LLZO in the composite cathodes, which is critical for successful operation. This research project aimed to use novel processing methods to overcome these issues. The end result was the first ever-reported truly all solid-state battery based on LLZO operating at room temperature without application of exogenous pressure. During the course of the project, we also identified a number of issues that need to be addressed to improve the technology readiness level of this battery.

25 ENERGY STORAGE↗
DOE OSTI2023

Fundamental Superconductivity of Nb films for Quantum Computing Application

Niobium is a widely accepted material for quantum computing device as well as superconducting radio frequency (SRF) technology. Superconducting niobium is a marginal type II superconductor which has a very narrow gap (~20-30 mT) of the mixed state at 2K, even showing the intermediate state (IMS) at the early stage of magnetic vortex penetration. Tremendous progress has been made in understanding the impact of the Nb surface and bulk superconductivities on SRF resonator performance. However, the effect of thin superconducting Nb films for quantum computing applications requires further examination. In this study, we explore the fundamental superconducting properties of various thin Nb films and compare them with respect to the energy relaxation time, T1, measured from superconducting qubit fabricated with these films. The Nb films are fabricated both with or without a surface protective layer that prevents the formation of lossy Nb2O5. Electromagnetic properties are characterized by means of bulk magnetization, electromagnetic transport, and dynamics of surface superconductivity. In addition, analytical electron microscopy is implemented to further connect the superconducting properties to microstructure.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Multifunctional Nanofiber Reinforcement for Improved Thermomechanical and Chemical Stability of Perovskite Solar Cells

This project focused on the development of metal halide perovskite-polymeric nanofiber nanocomposites for robust and efficient solar cells. Metal halide perovskite solar cells are a potentially disruptive technology with high efficiencies and low-cost solution processability amenable with roll-to-roll fabrication of flexible devices. However, perovskites exhibit extreme brittleness, high internal film stresses, and chemical instabilities that significantly limit service lifetimes under normal operating conditions. To date, most work addressing these shortcomings has been focused on encapsulating devices between thick layers of rigid materials such as glass, which increases the total weight and cost of devices. Furthermore, these rigid and heavy encapsulants do not translate well to emerging solar markets vital for national security, including integrated mobile power, emergency deployments for disaster relief and military engagement, and lightweight power for space. It is therefore critical to improve the thermomechanical and chemical stability of perovskite devices in a way that is compatible with flexible and lightweight substrates. In this project, we integrated nylon-6,6 nanofibers into MAPbI3 to mechanically reinforce the perovskite, demonstrating films that exhibited fracture energies 5-fold greater than pristine MAPbI3 while also maintaining similar power conversion efficiencies due to beneficial light scattering effects from the polymeric nanofibers. These results required successful development of approaches to control the deposition thickness of nanofiber mats down to 100s of nanometers, and to ensure the polymer nanofibers did not inhibit charge transport to the at the perovskite-transport layer interface.

14 SOLAR ENERGY↗
NASA NTRS1970

Motor brush wear measured with strain gages

Balanced bridge circuit, supplied with low-voltage direct current and connected to a readout device, measures remaining brush material, rate of brush wear, armature runout, and brush signature.

Farrell, W. T.↗