Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Geologic Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

The Effects of Heterogeneities on Seismic Wave Propagation in the Climax Stock

The Comprehensive Nuclear Test-Ban Treaty requires the ability to detect low-yield (less than 150kton) nuclear events. This kind of monitoring can only be done seismically on a regional scale (within 2000km). At this level, it is difficult to distinguish between low-yield nuclear events and non-nuclear events of similar magnitude. In order to confidently identify a nuclear event, a more detailed understanding of nuclear seismic sources is needed. In particular, it is important to know the effects of local geology on the seismic signal. This study focuses on P-wave velocity in heterogeneous granitoid. The Source Physics Experiment (SPE) is currently performing low-yield tests with chemical explosives at the Nevada National Security Site (NNSS). The exact test site was chosen to be in the Climax Stock, a cretaceous granodiorite and quartz-monzonite pluton located in Area 15 of the NNSS. It has been used in the past for the Hard Hat and Pile Driver nuclear tests, which provided legacy data that can be used to simulate wave propagation. The Climax Stock was originally chosen as the site of the SPE partly because of its assumed homogeneity. It has since been discovered that the area of the stock where the SPE tests are being performed contains a perched water table. In addition, the stock is known to contain an extensive network of faults, joints, and fractures, but the exact effect of these structural features on seismic wave velocity is not fully understood. The SPE tests are designed to seismically capture the explosion phenomena from the near- to the far-field transition of the seismic waveform. In the first SPE experiment, 100kg of chemical explosives were set off at a depth of 55m. The blast was recorded with an array of sensors and diagnostics, including accelerometers, geophones, rotational sensors, short-period and broadband seismic sensors, Continuous Reflectometry for Radius vs. Time Experiment, Time of Arrival, Velocity of Detonation, and infrasound sensors. The focus of this study is two-fold: (1) the geophone array that was focused over the SPE shot and (2) a high-resolution seismic profile that was recently acquired at the field site. The geophone array was placed radially around the SPE shot in five directions with 100m spacing and out to a distance of 2 km. The high-resolution profile was about 475m in length with station and shot spacing of 5m using a 7000lb mini-vibe as a source. In both data sets, the first arrivals will be used to develop velocity models. For the geophone array, 1-D P-wave velocity models will be developed to determine an average apparent velocity of the Climax Stock. The high-resolution data will be used to develop a 2-D P-wave velocity model along the seismic profile. This is in an effort to elucidate the water table in more detail and provide additional information on the near-surface structure. These results will be used in the overall modeling effort to fully characterize the test bed and develop a physics-based model to simulate seismic energy from the SPE events.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Transmission electron microscopy with in-situ ion irradiation: Facilities and community

Whilst there is a clear scientific and technological need for the technical capabilities of transmission electron microscopes with in-situ ion irradiation, it also requires a collaborative community of international researchers to support such facilities in successfully meeting this demand. Instruments of this type serve to provide fundamental understanding of the mechanisms which drive changes in materials important to nuclear fission and fusion energy, the semiconductor industry, quantum information systems, space travel, astronomy, geology and many more applications. As these areas continue to evolve and the instrumentation possibilities expand, the capacity of in-situ ion irradiation facilities must also develop hand-in-hand with the user community to deliver an ever-greater diversity of high-fidelity extreme-environment experimentation. Future directions for the field, such as miniaturization from MEMS/microfluidic devices and advanced controls with ML-based analysis, continuously emerge to advance both the hardware and software which support the coupling of TEMs with ion beams. This review sets out to provide up-to-date insights into the community and advancement of current, and development of future, facilities which have the potential to further unlock access to the nanoscale exploration of coupled extreme environments crucial to many of the important science and engineering challenges we face today.

In-situ irradiation↗

Characterizing the Atmospheric Mn Cycle and Its Impact on Terrestrial Biogeochemistry

Abstract The role of manganese (Mn) in ecosystem carbon (C) biogeochemical cycling is gaining increasing attention. While soil Mn is mainly derived from bedrock, atmospheric deposition could be a major source of Mn to surface soils, with implications for soil C cycling. However, quantification of the atmospheric Mn cycle, which comprises emissions from natural (desert dust, sea salts, volcanoes, primary biogenic particles, and wildfires) and anthropogenic sources (e.g., industrialization and land‐use change due to agriculture), transport, and deposition, remains uncertain. Here, we use compiled emission data sets for each identified source to model and quantify the atmospheric Mn cycle by combining an atmospheric model and in situ atmospheric concentration measurements. We estimated global emissions of atmospheric Mn in aerosols (<10 μm in aerodynamic diameter) to be 1,400 Gg Mn year −1 . Approximately 31% of the emissions come from anthropogenic sources. Deposition of the anthropogenic Mn shortened Mn “pseudo” turnover times in 1‐m‐thick surface soils (ranging from 1,000 to over 10,000,000 years) by 1–2 orders of magnitude in industrialized regions. Such anthropogenic Mn inputs boosted the Mn‐to‐N ratio of the atmospheric deposition in non‐desert dominated regions (between 5 × 10 −5 and 0.02) across industrialized areas, but that was still lower than soil Mn‐to‐N ratio by 1–3 orders of magnitude. Correlation analysis revealed a negative relationship between Mn deposition and topsoil C density across temperate and (sub)tropical forests, consisting with atmospheric Mn deposition enhancing carbon respiration as seen in in situ biogeochemical studies.

Environmental Sciences & Ecology↗

Molybdenum Burial Mechanism in Sulfidic Sediments: Iron-Sulfide Pathway

Relative to continental crust, sediments underlying sulfidic marine waters are molybdenum-rich, a property preserved in the rock record and useful for characterizing paleoenvironments. The enrichment mechanism is not agreed upon but is attributed at least partly to deposition of Fe–Mo–S compounds, which are as yet uncharacterized. Here, we determine the composition and stability of colloidal Fe–Mo–S precipitates formed at mildly basic pH and H 2 S(aq) > 10 –5 M. The first product consists simply of FeMoS 4 , with K sp = 10 –14.95 . Within hours, FeMoS 4 irreversibly transforms by internal self-reduction to a Mo(IV) product of similar composition. The reduced product is insoluble in 1 M HCl but soluble in concentrated HNO3, implying that it would be recovered with pyrite in a common assay of sediments. X-ray absorption fine structure data show that Mo(IV) in the colloids is coordinated by a split first shell of about five sulfur atoms at average distances of 2.31 and 2.46 Å and in its second shell by an iron atom at about 2.80 Å. These properties resemble those determined for Mo in modern anoxic lake sediments and in Phanerozoic black shales. The atomic environment around Mo suggests that the colloidal products may be inorganic polymers containing cuboid, Fe 2 Mo 2 S 4 4+ cores. Such materials are so far unreported by mineralogists, although a rare mineral, jordisite, may be a related, but more Mo-rich material. The low solubility of FeMoS 4 makes it a feasible precipitate in euxinic waters like those in the modern Black Sea. We propose that colloids similar to those studied here could account for Mo-enrichment in euxinic basin sediments and black shales.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Controls on Stable Methane Isotope Values in Northern Peatlands and Potential Shifts in Values Under Permafrost Thaw Scenarios

Abstract Northern peatlands are a globally significant source of methane (CH 4 ), and emissions are projected to increase due to warming and permafrost loss. Understanding the microbial mechanisms behind patterns in CH 4 production in peatlands will be key to predicting annual emissions changes, with stable carbon isotopes (δ 13 C‐CH 4 ) being a powerful tool for characterizing these drivers. Given that δ 13 C‐CH 4 is used in top‐down atmospheric inversion models to partition sources, our ability to model CH 4 production pathways and associated δ 13 C‐CH 4 values is critical. We sought to characterize the role of environmental conditions, including hydrologic and vegetation patterns associated with permafrost thaw, on δ 13 C‐CH 4 values from high‐latitude peatlands. We measured porewater and emitted CH 4 stable isotopes, pH, and vegetation composition from five boreal‐Arctic peatlands. Porewater δ 13 C‐CH 4 was strongly associated with peatland type, with δ 13 C enriched values obtained from more minerotrophic fens (−61.2 ± 9.1‰) compared to permafrost‐free bogs (−74.1 ± 9.4‰) and raised permafrost bogs (−81.6 ± 11.5‰). Variation in porewater δ 13 C‐CH 4 was best explained by sedge cover, CH 4 concentration, and the interactive effect of peatland type and pH (r 2 = 0.50,p < 0.001). Emitted δ 13 C‐CH 4 varied greatly but was positively correlated with porewater δ 13 C‐CH 4 . We calculated a mixed atmospheric δ 13 C‐CH 4 value for northern peatlands of −65.3 ± 7‰ and show that this value is more sensitive to landscape drying than wetting under permafrost thaw scenarios. Our results suggest northern peatland δ 13 C‐CH 4 values are likely to shift in the future which has important implications for source partitioning in atmospheric inversion models.

Environmental Sciences & Ecology↗

Synthesis and Single Crystals of Refractory Oxides of Lanthanides and Thorium

At the completion of this program, we can report that we developed a considerable degree of technical improvements in our ability to perform hydrothermal reactions at high temperatures and pressures. We can now routinely perform reactions at 700-750°C and 200 MPa. Currently we are in the process of exploiting this new technology synthesizing a range of exotic new materials investigating relatively poorly understood materials. Our initial efforts focused on the chemistry of rare earth oxides with tetravalent and pentavalent oxides. We recently published a study of the lanthanides with Nb 5+ and Ta 5+ ions, where we grew oxides such as RENdO 4 and RETaO 4 as high quality single crystals. These compounds were targeted as potential hosts for luminescent and scintillation materials, particularly given that they are among the densest oxide hosts and hence have good potential as absorbers for high energy radiation like X-rays and gamma rays. We also isolated a range of unusual new rare earth tantalates with very complex structures. indicating that the chemistry is very sensitive to conditions. We performed some fairly comprehensive examinations of the solid-state chemistry of rare earth ions with various tetravalent metal ions especially Si 4+ , Ge 4+ , Sn 4+ and Ti 4+ . Given the potential role of rare earth silicates in immobilizing radioactive waste elements in long-term storage, and the similarity of our hydrothermal fluids with known geological conditions, this chemistry continues to be relevant. We prepared an extensive series of new lanthanide germanates (e.g. RE 13 Ge 6 O 31 (OH), BaRE 10 (GeO 4 ) 4 O 8 ). and found that there is there is almost no overlap between the chemistry of the rare earth silicates. Stannic oxide (SnO 2 ) is much more refractory and requires higher temperatures and of mineralizer concentrations. One significant result is the growth of RE 2 Sn 2 O 7 pyrochlore single crystals. These are of interest because the rare earth stannate pyrochlores are known to display a wide range of magnetic frustration such as spin ice behavior. We grew high quality single crystals of rare earth germanate and stannate pyrochlores and this led to a collaboration with Professor Kate Ross at Colorado State. Preliminary measurements, indicate that the crystals contain no detectable defects or site disorder. Initial neutron diffraction on single crystals was performed at Oak Ridge, and more detailed experiments involving the Ross group are underway at both NIST and ORNL. This particular chemistry has turned out to be the most potentially significant work on this project and the collaborative effort with Prof. Ross is the topic of a DoE renewal project on quantum materials. Our initial foray into the hydrothermal chemistry of rare earth titanates has also been very promising and a range of cubic and polar ferroic phases of the light rare earths RE 2 Ti 2 O 7 (RE = La - Pr) in the P2 1 phase. We also discovered an interesting new phase Ce 2 Ti 4 O 11 that can have implications in heavy metal immobilization and storage. along with a series of new rare earth titanates (La 5 Ti 4 O 15 (OH) Sm 3 TiO 5 (OH) 3 and Lu 5 Ti 2 O 11 (OH) with exceptionally complex structures. One interesting sidelight has been high temperature hydrothermal chemistry terbium, including the growth of large crystals of TbO(OH). This is not a new compound but it is the first time it has been grown as large single crystals. The Tb atom density is almost as high as that in Tb 2 O 3 and has a very high Verdet constant (ca. 70), making it a very attractive candidate as a Faraday rotator. Unfortunately it is not in a cubic structure but he material is hard, stable, pure and inexpensive, so should still be an attractive Faraday oscillator. We recently received a patent on this material. We also synthesized K 2 Tb(Ge 2 O 7 ) containing stable octahedral Tb 4+ ions, which appears to be the first example of a well-characterized Tb 4+ complex. Given that Tb 4+ has been proposed as a benign surrogate for more treacherous tetravalent ions such as Cf 4+ and Bk 4+ , we think that Tb 4+ silicates can be a particularly useful study for actinide immobilization and related work. We also began reaction studies with rare earths and both ReO 2 and RuO 2 . These resulted in large single crystals of species like RE 5 Ru 2 O 12 , RE 4 Re 2 O 11 , REReO 4 and RE 2 ReO 5 . Several of these samples have already been sent to ORNL for magnetic and neutron diffraction studies.

36 MATERIALS SCIENCE↗

Robust In-Situ Strain Measurements to Monitor CO 2 Storage

The goal of this project was to develop and demonstrate robust instrumentation to monitor the in-situ strain tensor in order to improve the reliability and security of CO 2 storage in geologic formations. We met the original goals of the project and the major overarching accomplishment is the advancement of strain tensor monitoring from an intriguing concept to a commercially available technology with a solid foundation of novel instruments supported by theoretical analyses and validation experiments. The main accomplishments of the project are summarized below. We designed, built and evaluated nine new optical fiber strainmeters and tiltmeters using Michelson interferometers to measure deformation with ultra-high resolution at both shallow and deep point locations in the subsurface. These are the robust strainmeters that motivated the title of the project. We designed, built and evaluated a novel method of measuring distributed strain in optical fibers with nanostrain resolution, and cm-scale location, and sampling into the seismic band. The new method is called Coherence-length-gated Microwave Photonics Interfereometry (CMPI). CMPI technology has advantages over existing commercial DAS and DSS methods. We developed and demonstrated capabilities to deploy instruments in the field and used them to measure strain caused by ambient signals like barometric pressure and tides, as well as induced signals like surface loading and pore pressure changes from pumping tests. We deployed a working strainmeter at 1,700 ft depth, slightly above an active reservoir. This is to our knowledge the greatest depth a strainmeter has been deployed and the techniques we used can readily be extended to greater depths. Optical fiber borehole tensor strainmeter techology was advanced from a TRL 4 at the start, to a TRL of 7 at the conclusion of the project. The project included advances in simulations and theoretical analyses. We developed and demonstrated a computational workflow that uses machine learning to reduce the computational requirements and make it practical to use Bayesian inversion to solve large numerical poroelastic analyses needed to interpret strain tensor field data. We evaluated the strain tensor fields and time series that would be caused by leaks of CO 2 or other fluids from reservoirs. These simulations demonstrated that signals from leaks could be measured with instruments developed for the project, opening a potentially new method for ensuring storage security. We showed that strains in caprock can be used to estimate pressure in a reservoir. This avoids the need to drill monitoring wells into the reservoir, and it expands the capabilities of monitoring in the caprock. The project includes a derivation and application of a novel analytical solution to the strains in the vicinity of a pressurized poroelastic inclusion. This solution explains field data measured during injeciton tests at the North Avant Field, and it will simplify future interpretation of strain tensor data. The project included a broad range of experiments, and of the most significant is the characterization of the strain tensor at an array three strainmeters during six injection tests at the North Avant Field, Oklahoma. This demonstrated repeatability of the strain signal measured by the new instruments developed for the project, and it showed similarities between the strain signal at shallow depths and pressure in the underlying reservoir. We also demonstrated that useful strain data can be measured at reservoir depths. This confirms that strain tensor data can be measured throughout the caprock over a reservoir. The project demonstrated the feasibility of using the strain tensor and distributed strain measured in caprock during a variety of different well tests where the pumping rate was constant, sinusoidal and positive, or a periodic square wave with zero net rate. This further strengthens the validity of using strain data to characterize reservoirs and aquifers. We also demonstrated that strain caused be fluctuations of air pressure and water pressure in the vadose zone can be measured and interpreted, suggesting that high resolution distributed strain measurements hold promise for monitoring the vadose zone. The project partially supported nine graduate students in the Environmental Engineering, Hydrogeology, Electrical Engineering programs at Clemson University. The research was described in nine journal papers, 23 talks and conference abstracts. Additional journal papers are in preparation. A new company called Tensora was started to provide strainmeter technology for commercial applications.

01 COAL, LIGNITE, AND PEAT↗

Chemistry of diagenetic features analyzed by ChemCam at Pahrump Hills, Gale crater, Mars

The Curiosity rover's campaign at Pahrump Hills provides the first analyses of lower Mount Sharp strata. We report ChemCam elemental composition of a diverse assemblage of post-depositional features embedded in, or cross-cutting, the host rock. ChemCam results demonstrate their compositional diversity, especially compared to the surrounding host rock: (i) Dendritic aggregates and relief enhanced features, characterized by a magnesium enhancement and sulfur detection, and interpreted as Mg-sulfates; (ii) A localized observation that displays iron enrichment associated with sulfur, interpreted as Fe-sulfate; (iii) Dark raised ridges with varying Mg- and Ca-enriched compositions compared to host rock; (iv) Several dark-toned veins with calcium enhancement associated with fluorine detection, interpreted as fluorite veins. (v) Light-toned veins with enhanced calcium associated with sulfur detection, and interpreted as Ca-sulfates. The diversity of the Pahrump Hills diagenetic assemblage suggests a complex post-depositional history for fine-grained sediments for which the origin has been interpreted as fluvial and lacustrine. Assessment of the spatial and relative temporal distribution of these features shows that the Mg-sulfate features are predominant in the lower part of the section, suggesting local modification of the sediments by early diagenetic fluids. Conversely, light-toned Ca-sulfate veins occur in the whole section and cross-cut all other features. A relatively late stage shift in geochemical conditions could explain this observation. The Pahrump Hills diagenetic features have no equivalent compared to targets analyzed in other locations at Gale crater. Only the light-toned Ca-sulfate veins are present elsewhere, along Curiosity's path, suggesting they formed through a common late-stage process that occurred at over a broad area.

58 GEOSCIENCES↗

Physical property characteristics of gas hydrate-bearing reservoir and associated seal sediments collected during NGHP-02 in the Krishna-Godavari Basin, in the offshore of India

India’s National Gas Hydrate Program Expedition 02 (NGHP-02) was conducted to better understand geologic controls on gas hydrate occurrence and morphology, targeting coarse-grained sediments along the lower continental slope offshore eastern India. This study combines seismic, logging-while-drilling data, and a petroleum system approach to provide a regional geologic and lithologic context for: 1) gas hydrate morphology and distribution, and 2) effects of fine-grained sediments (clays and other grains smaller than 63µm) on gas production in NGHP-02 Area B in the Krishna-Godavari Basin. Area B seismic data show a buried anticline/syncline structure with strong reflectors, R1 and R2, that delineate two of the five lithologic units: Unit I (shallowest), II (R1), III, IV (R2) and V (below the bas of gas hydrate stability). Throughout Area B, gas hydrate morphology depends on its placement within these units. Specifically, core- and grain-scale measurements indicate fines content exerts a primary control on the gas hydrate distribution and morphology. Units I, II and III are generally fine-grained. On the anticline crest, these units host primarily grain-displacing gas hydrate veins linked to pore-occupying gas hydrate in thin, localized, coarser-grained deposits. Diatoms in Unit III increase porosity with depth, reaching ~70% where it contacts Unit IV, the gas hydrate reservoir associated with reflector R2. The Unit III lithology and porosity allow fluid and dissolved-phase methane to escape Unit IV and form gas hydrate in the fine-grained overburden. Within Unit IV, fine-grained layers are interbedded with coarser-grained gas hydrate reservoir sands, and the fines content even in the sands is high enough to impact hydraulic and mechanical properties during gas production. Fluid motion during gas production can mobilize fines, which can then clog pore throats, limiting production rates. In conclusion, pore-water freshening during gas hydrate dissociation can increase fines mobilization, particularly given the smectite identified in the fine-grained interbeds.

03 NATURAL GAS↗

Dynamics of streamflow permanence in a headwater network: Insights from catchment-scale model simulations

The hillslope and channel dynamics that govern streamflow permanence in headwater systems have important implications for ecosystem functioning and downstream water quality. Recent advancements in process-based, semi-distributed hydrologic models that build upon empirical studies of streamflow permanence in well-monitored headwater catchments show promise for characterizing the dynamics of streamflow permanence in headwater systems. However, few process-based models consider the continuum of hillslope-stream network connectivity as a control on streamflow permanence in headwater systems. The objective of this study was to expand a process-based, catchment-scale hydrologic model to better understand the spatiotemporal dynamics of headwater streamflow permanence and to identify controls of streamflow expansion and contraction in a headwater network. Further, we aimed to develop an approach that enhanced the fidelity of model simulations, yet required little additional data, with the intent that the model might be later transferred to catchments with limited long-term and spatially explicit measurements. This approach facilitated network-scale estimates of the controls of streamflow expansion and contraction, albeit with higher degrees of uncertainty in individual reaches due to data constraints. Our model simulated that streamflow permanence was highly dynamic in first-order reaches with steep slopes and variable contributing areas. The simulated stream network length ranged from nearly 98±2% of the geomorphic channel extent during wet periods to nearly 50±10% during dry periods. The model identified a discharge threshold of approximately 1 mm d –1 , above which the rate of streamflow expansion decreases by nearly an order of magnitude, indicating a lack of sensitivity of streamflow expansion to hydrologic forcing during high-flow periods. Overall, we demonstrate that process-based, catchment-scale models offer important insights on the controls of streamflow permanence, despite uncertainties and limitations of the model. We encourage researchers to increase data collection efforts and develop benchmarks to better evaluate such models.

54 ENVIRONMENTAL SCIENCES↗

Unique Facilities, Innovative Treatment Processes, and a Talented Workforce Allow Fluor Idaho to Successfully Disposition Transuranic Waste - 18388

Fluor Idaho is utilizing state-of-the-art equipment, treatment technologies, and employee expertise at the Department of Energy's (DOE) Idaho Site to treat contact-handled transuranic (CH-TRU) waste, as well as extremely challenging remote-handled transuranic (RH-TRU) waste forms, to prepare the material for shipment and permanent disposal at the Department's Waste Isolation Pilot Plant (WIPP). Nowhere else in the DOE Complex - perhaps the world - will one find the compilation of tools and an experienced workforce with an unparalleled history of safely retrieving, characterizing, treating, repackaging, certifying, and shipping TRU waste. Since 2003, the Advanced Mixed Waste Treatment Project (AMWTP) has used both conventional and unique retrieval concepts, high-tech characterization equipment - including real-time radiography and radioassay - robotics, and automated treatment processes to retrieve and treat 65,000 cubic meters of above-ground CH-TRU waste. Additionally, engineered controls and specialized personal protective equipment have allowed employees to make thousands of entries into high-radiation areas without a skin or clothing contamination incident - evidence of the employees' commitment to safety. AMWTP has encountered and found solutions for many challenging waste forms, including polychlorinated biphenyl-contaminated wastes, TRU waste containers with up to 1,000 fissile gram equivalent plutonium-239, oversized TRU boxes, and partially absorbed organic sludge waste. By utilizing additional facilities and equipment at the Accelerated Retrieval Project V and VII, Fluor Idaho has developed new processing lines and capabilities to ensure worker safety and milestone completion. These two soft-sided buildings, located at a facility adjacent to AMWTP, were originally constructed to exhume Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) TRU wastes from a section of a 97-acre landfill. After a total of 1,150 cubic meters of targeted waste were removed, personnel, working in collaboration with state regulators, successfully implemented a unique regulatory strategy that allowed these CERCLA facilities to be modified and permitted to treat Resource Conservation and Recovery Act (RCRA) wastes from the AMWTP - a savings of tens of millions of dollars over the cost of constructing new buildings. Adding to the AMWTP's technological uniqueness is its ability to treat wastes from other facilities in the DOE Complex. Two prior decision documents and an agreement with the state of Idaho have allowed AMWTP to treat wastes from 15 other DOE sites. It is the only project in the complex to have done so. At another project located next to AMWTP, targeted waste exhumation within the Subsurface Disposal Area is approximately two years ahead of schedule. Crews have removed more than 8,600 cubic meters of CH-TRU and hazardous wastes from eight exhumation areas that equal a combined footprint of 4.75 acres. Less than one acre remains to be exhumed to satisfy the 2008 Record of Decision waste exhumation end state between the DOE, Environmental Protection Agency, and state of Idaho. Construction of the final building where targeted waste exhumation will continue was completed during the summer of 2017. Exhumation will be completed within the next few years. Following exhumation completion, an evapotranspiration barrier (or cap) will be constructed over the entire landfill. Fluor Idaho continues to make progress on a more challenging project involving an inventory of RH-TRU waste that also contains the reactive metal sodium. Crews are utilizing hot cells, once used for spent nuclear fuel reprocessing and high-level waste treatment at the Idaho Nuclear Technology and Engineering Center, to render this challenging waste form safe for disposal in a national geologic waste repository. The treatment methods being employed on this RH-TRU waste are unique in the DOE Complex. Minute concentrations of water are sprayed onto the sodium-contaminated material in a process called 'spritzing' to chemically change the sodium from a reactive metal to a non-reactive salt. In other cases, sodium-contaminated waste is dipped in water to initiate a reaction in a process called 'immersion.' Lastly, for more challenging waste shapes that could not be successfully treated with the two prior methods, crews lower the sodium-contaminated RH-TRU waste into a one-of-a-kind distillation unit that uses high temperature and vacuum to volatilize the sodium and recapture it in a condenser unit for disposal. The RH-TRU waste treated with this technology is then safe for permanent disposal. Fluor Idaho is proud to operate DOE's CH- and RH-TRU waste treatment facilities, as well as use innovative processes and its talented workforce to complete this important work-scope. Such capabilities allow the contractor to meet the commitments made by the DOE to the state of Idaho. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Ecosystem carbon transit versus turnover times in response to climate warming and rising atmospheric CO 2 concentration

Ecosystem carbon (C) transit time is a critical diagnostic parameter to characterize land C sequestration. This parameter has different variants in the literature, including a commonly used turnover time. However, we know little about how different transit time and turnover time are in representing carbon cycling through multiple compartments under a non-steady state. In this study, we estimate both C turnover time as defined by the conventional stock over flux and mean C transit time as defined by the mean age of C mass leaving the system. We incorporate them into the Community Atmosphere Biosphere Land Exchange (CABLE) model to estimate C turnover time and transit time in response to climate warming and rising atmospheric [CO 2 ]. Modelling analysis shows that both C turnover time and transit time increase with climate warming but decrease with rising atmospheric [CO 2 ]. Warming increases C turnover time by 2.4 years and transit time by 11.8 years in 2100 relative to that at steady state in 1901. During the same period, rising atmospheric [CO 2 ] decreases C turnover time by 3.8 years and transit time by 5.5 years. Our analysis shows that 65&thinsp;% of the increase in global mean C transit time with climate warming results from the depletion of fast-turnover C pool. The remaining 35&thinsp;% increase results from accompanied changes in compartment C age structures. Similarly, the decrease in mean C transit time with rising atmospheric [CO 2 ] results approximately equally from replenishment of C into fast-turnover C pool and subsequent decrease in compartment C age structure. Greatly different from the transit time, the turnover time, which does not account for changes in either C age structure or composition of respired C, underestimated impacts of warming and rising atmospheric [CO 2 ] on C diagnostic time and potentially led to deviations in estimating land C sequestration in multi-compartmental ecosystems.

54 ENVIRONMENTAL SCIENCES↗

Subtask 1.5 – CO2 Injection Monitoring with an Optimized Scalable, Automated, Semipermanent Seismic Array

The scalable, automated, semipermanent seismic array (SASSA) method is a flexible and relatively cost-effective surface geophysical method for regular time-lapse monitoring of the movement of injected carbon dioxide (CO2) in a reservoir for CO2 enhanced oil recovery (EOR) or geologic CO2 storage operations. It has the advantages of a low-environmental-footprint while monitoring regions of a reservoir from the surface without the need for a regular grid distribution of receivers. Automated data collection is possible. As only time-lapse amplitude changes at the reservoir level due to CO2 movement within the reservoir are monitored, the turnaround time to deliver results from the SASSA method can be short, without the need for long, time-consuming data-processing workflows. As data is collected and processed, incremental information can be provided to the field operator. The Energy & Environmental Research Center (EERC) conducted a SASSA field test from September 2018 to November 2020 in a portion of the Bell Creek Field in Montana, which implemented new CO2 EOR field activities during the study period. Lessons learned from a proof-of-concept study were incorporated to improve the data quality of the SASSA method and demonstrate the viability of the technology. The EERC implemented several enhancements to improve data quality, including 1) an iterative survey design, which allowed placing the receivers in strategic locations where the movement of the CO2 in the reservoir could be tracked with minimum interference by the cultural noise in the study area; 2) the use of powerful seismic sources in the form of surface orbital vibrators, and 3) data acquisition during optimal periods. History-matched reservoir simulation was performed to predict gas saturation and pressure response induced by CO2 injection in the study area. The results were compared with the SASSA-measured responses to CO2 injection as a partial validation technique. A match between the two methods was observed for most of the SASSA points predicted to have intersected a CO2 saturation change. The validated results provide confidence that the SASSA method can be used independently as a CO2 saturation monitoring technique. As data are collected and processed, incremental information can be provided to the field operator. The critical components of the SASSA workflow for a successful application of the method are the following: Iterative survey design with information about CO2 injection activities from the oilfield operator. A detailed CO2 injection plan is the key driver to select the strategic monitoring location of the SASSA sensors. After this information is incorporated in the initial distribution of sources and receivers in the study area, high-resolution satellite images are used to identify ground locations not affected by cultural noise sources, such as power lines, pipelines/flow lines, or roadways. In the next iteration of the survey design, a scouting trip to the study area is needed to understand more details of the noise sources identified in the previous step and the intensity of the field activities that can also generate noise during the monitoring. Integrating the information from the scouting trip into the survey design to select the optimum source and receiver locations is the final step. Noise attenuation. The variety of noise types during seismic monitoring of an oil field is enormous. Tailored noise characterization and processing at a node-by-node level can enhance the performance and sensitivity of the SASSA technique. Future advancements that could improve the efficiency and application of the SASSA technology include: Gaining a better understanding of the noise field produced by the seismic source to aid the choice of receiver location. Surface noise from the source can overwhelm the small signal changes due to CO2 that the SASSA method measures. Improved data-processing workflow to automatically analyze and adapt to dynamic noise conditions associated with industrial settings. This subtask was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE- FE0024233.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

High-resolution analysis of clay minerals and amorphous materials in martian analog environments

Mudrocks and mud-sized sediments (i.e., silt to clay) dominate the surface of Earth and Mars. These fine-grained sediments preserve a rich history of sedimentary processes from source to sink and shed light on ancient climates. However, both the physical and chemical nature of these materials make them difficult to fully characterize with traditional laboratory techniques. Here, we explore a cross-disciplinary and high-resolution approach using synchrotron radiation for X-ray diffraction, pair distribution function analysis, and submicrometer-scale X-ray fluorescence, combined with transmission electron microscopy, to better understand the nanostructure and composition of mud-sized sediments from a glacio-fluvial watershed in southwest Iceland. Our results demonstrate that sediments in the cold and wet climate of Iceland are more altered than previously thought, as evidenced by the identification of kaolinite and mixed-layer kaolinite-smectite. Additionally, sediments are enriched in amorphous materials and nanocrystalline phases, as determined from grain morphologies and compositions consistent with allophane, hisingerite, ferrihydrite, and halloysite. These alteration products are present as intimate mixtures that vary across depositional sites, demonstrating the dynamic nature of the secondary assemblage from source to sink. This work has implications for Mars, where, for example, basalt-sourced sedimentary rocks from Gale crater are abundant in clay minerals and amorphous materials. Finally, this work underpins the importance of using high-resolution techniques, a coordinated methodology, and developing innovative approaches for future planetary sample return missions (e.g., Mars sample return).

36 MATERIALS SCIENCE↗

Natural CO 2 accumulations in the western Williston Basin: A mineralogical analog for CO 2 injection at the Weyburn site

The Devonian carbonates of the Duperow Formation on the western flank of the Williston Basin in southwest Saskatchewan contain natural accumulations of CO 2 , and may have done so for as long as 50 million years. These carbonate sediments are characterized by a succession of carbonate cycles capped by anhydrite-rich evaporites that are thought to act as seals to fluid migration. The Weyburn CO 2 injection site lies 400 km to the east in a series of Mississippian carbonates that were deposited in a similar depositional environment. That long-term isolation of natural CO 2 can be accomplished within carbonate strata has motivated the investigation of the Duperow rocks as a potential natural analog for storage of anthropogenic CO 2 in carbonate lithologies. For the Duperow strata to represent a legitimate analog for Midale injection and storage, the similarity in lithofacies, whole rock compositions, mineral compositions and porosity with the Midale Beds must be established. Here we compare lithofacies, whole rock compositions, mineralogy and mineral compositions from both locales. The major mineral phases at both locales are calcite, dolomite and anhydrite. In addition, accessory pyrite, fluorite, quartz and celestine (strontium sulfate) are also observed. Dawsonite, a potential CO 2 -trapping mineral, is not observed within the CO 2 -bearing horizons of the Duperow Formation, however. The distribution of porosity in the Midale Vuggy units is similar to that of the Duperow Formation, but the Marly units of the Midale have significantly higher porosity. The Duperow Formation is topped by the Dinesmore evaporite that is rich in anhydrite, and often contains authigenic K-feldspar. The chemistry of dolomite and calcite from the two localities also overlaps. Silicate minerals are in low abundance (<3%) within the analyzed Duperow samples, with quartz and K-feldspar the only silicates observed petrographically or in X-ray diffraction patterns. The Midale Beds contain significantly higher silica/silicate concentrations (Durocher et al., 2003), but the paucity of mono- and divalent cations that can be derived from dissolution of these silicate minerals likely precludes significant carbonate mineral formation. Therefore physical and solution trapping are likely to be the primary CO 2 trapping mechanisms at both sites.

58 GEOSCIENCES↗

Potosi Reservoir Modeling; History and Recommendations

As a part of a larger project co-funded by the United States Department of Energy (US DOE) to evaluate the potential of formations within the Cambro-Ordovician strata above the Mt. Simon as potential targets for carbon sequestration in the Illinois and Michigan Basins, the Illinois Clean Coal Institute (ICCI) requested Schlumberger to evaluate the potential injectivity and carbon dioxide (CO₂) plume size of the Cambrian Potosi Formation. The evaluation of this formation was accomplished using wireline data, core data, pressure data, and seismic data from two projects: the US DOE-funded Illinois Basin–Decatur Project being conducted by the Midwest Geological Sequestration Consortium in Macon County, Illinois, as well as data from the Illinois – Industrial Carbon Capture and Sequestration (IL-ICCS) project funded through the American Recovery and Reinvestment Act. In 2010, technical performance evaluations on the Cambrian Potosi Formation were performed through reservoir modeling. The data included formation tops from mud logs, well logs from the Verification Well 1 (VW1) and the Injection Well (CCS1), structural and stratigraphic formation from three dimensional (3D) seismic data, and field data from several waste water injection wells for the Potosi Formation. The intention was for two million tonnes per annum (MTPA) of CO₂ to be injected for 20 years into the Potosi Formation. In 2013, updated reservoir models for the Cambrian Potosi Formation were evaluated. The data included formation tops from mud logs, well logs from the CCS1, VW1, and Verification Well 2 (VW2) wells, structural and stratigraphic formation from a larger 3D seismic survey, and field data from several waste water injection wells for Potosi Formation. The objective is to simulate the injection of CO₂ at a rate 3.5 million tons per annum (3.2 million tonnes per annum [MTPA]) for 30 years 106 million tons (96 MT total) into the Potosi Formation. The Potosi geomodeling efforts have evolved from using data from a single well in 2010 to the inclusion of data from three wells in 2013 which largely leverage the porosity and permeability logs plus knowledge of lost circulation zones. The first Potosi model (Potosi Geobody Model 2010) attempted to use the available seismic inversion data to inform the geomodel and predict vugular zones in advance of drilling VW1. Lost circulation zones in VW1 came in as the geologists predicted. The model was not implemented in subsequent simulation work. To date, reservoir models used for flow simulation work have relied predominately on Gaussian distributed properties (porosity and permeability) and have employed a single injection well. Potosi Model 2013b incorporated the new VW2 logs, and exhibited an extra level of sophistication by delineating the vugular intervals. This method added further realism that likely represents the best reservoir approximation to date. Where the 2010 reservoir models were 10 by 10 mi (16 by 16 km) in area, the 2013 models were expanded in size to 30 by 30 mi (48 by 48 km). The latest reservoir simulations show that a minimum of four injectors might be required to meet target injection rates. Still, there is data that requires further scrutiny and modeling methodologies that require testing for the Potosi Formation. This work is currently ongoing, and the next phase of the reservoir modeling intends to implement valuable data like porosity derived from seismic inversion, seismically derived geobodies, or a combination of both to further define vugular zones and the porosity distribution within the Potosi Formation. Understanding the dual porosity, dual permeability character of the Potosi remains the greatest challenge in representing this formation. Further analysis of the FMI* fullbore formation microimager data may aid in assessing this uncertainty. The Potosi Formation is indeed an interesting formation, and recommendations to further characterize it are included in the following list: - Data acquisition to identify the vugs permeability, distribution, and interconnectivity could be considered to perform a more rigorous evaluation of the Potosi Formation injectivity and capacity. This could be achieved by performing an injection test on a vugular interval to determine the vugs permeability, and an interference test between wells to evaluate the local vugs extent and interconnectivity. - A thorough study of the available FMI data may reveal specifics on estimating the vug to matrix ratio. This estimate could be used to further condition the porosity distribution. Porosity logs alone might underestimate the formation’s porosity associated with vugs. Porosity mapping derived from the seismic inversion could also be used in the succeeding task to characterize the lateral porosity distribution within the reservoir. This could involve the geobody methodology previously attempted in 2010. With or without seismic inversion porosity mapping, it is worth exploring whether increased lateral heterogeneity plays a significant role in Potosi injectivity. Investigations on vugular, dolomitic outcrops suggest that there may be significantly greater lateral heterogeneity than what has been modeled here. - The FMI data also reveals the presence of and helps describe open fractures. The presence of fractures will further enhance the formation’s permeability. The task of leveraging this data in the geomodeling effort still remains. Under the best of circumstances, this data describing open fractures may be combined with seismic attributes to delineate fracture corridors. Fracture modeling would certainly add another layer of sophistication to the model. Its contribution and applicability remain to be explored. - Facies modeling within the Potosi has yet to be thoroughly addressed. The carbonates during the time of deposition are believed to be regionally extensive. However, it may be worth delineating the reservoir with other regional wells or modern day analogues to understand the extent of the Potosi. More specifically, the model could incorporate lateral changes or trends if deemed necessary to represent facies transition. - Currently there is no fracture gradient data available for the Potosi in the Decatur project area. The acquisition of the fracture pressure data could be considered to determine an appropriate maximum allowable bottomhole injection pressure. This would allow the evaluation of injectivity and the required number of wells in a more precise manner. - Special core analysis (SCAL) to determine the relative permeability and capillary pressure of the vugs and matrix could be considered to have a better estimation of the reservoir injectivity and plume extent. - Formation water sampling and analysis could be considered for the Potosi to estimate the water salinity and properties. A vertical flow performance evaluation could be considered for the succeeding task to determine the appropriate tubing size, the required injection tubing head pressure, and to investigate whether the corresponding well injection rate falls within the tubing erosional velocity limit. - A simulation using several injectors could also be considered to determine the required number of wells to achieve the injection target while taking into account the pressure interference.

Smith, Valerie↗

Fluid-evaporation records preserved in salt assemblages in Meridiani rocks

We studied the inter-relationships between the major anions (SO{sub 3}, Cl, and Br) and cations (FeO, CaO and MgO) using elemental abundances determined by APXS in salt assemblages of RATted (abraded) rocks at Meridiani to characterize the behavior of fluids that infiltrated into this region on Mars. A plot of SO{sub 3} versus Cl for the abraded rocks yielded an unusual pattern, whereas the SO{sub 3}/Cl ratios versus Cl for the same rocks showed a monotonically decreasing trend represented by a hyperbola. The systematic behavior of the SO{sub 3} and Cl data in the documented rocks at Meridiani suggests that these anions behaved conservatively during fluid-rock interactions. These results further indicate that two kinds of fluids, referred to as SOL-I and SOL-II, infiltrated into Endurance/Eagle/Fram craters, where they underwent progressive evaporative concentration. SOL-I is a low pH fluid consisting of high SO{sub 3} and low Cl and high Br, (this fluid infiltrated all the way to the crater-top region), whereas SOL-II fluid of high pH with low SO{sub 3} and high Cl and low Br reached only an intermediary level known as the Whatanga contact at Endurance. Based on the FeO/MgO as well as CaO/MgO versus SO{sub 3}/Cl diagram for rocks above the Whatanga contact, the cation and anion relationships in this system suggest that the Fe{sup 2+}/SO{sub 4} and Ca{sup 2+}/SO{sub 4} ratios in SOL-I fluids at Meridiani were > 1 before the onset of evaporation based on the 'chemical divide' considerations. Below the Whatanga contact, relatively dilute SOL-II fluids seem to have infiltrated and dissolved/flushed away the easily soluble Mg-sulfate/chloride phases (along with Br) without significantly altering the SO{sub 3}/Cl ratios in the residual salt assemblages. Further, Cl/Br versus Br in rocks above the Whatanga contact show a hyperbolic trend suggesting that Cl and Br behaved conservatively similar to SO{sub 3} and Cl in the SOL-1 fluids at Meridiani. Our results are consistent with a scenario involving two episodes (SOL-I and SOL-II) of groundwater recharge at Meridiani Planum.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Roll Compaction of Powdered Radioactive Wastes - 18251

Most of low- and intermediate-level radioactive wastes must be solidified by a proper binding matrix and disposed at the centralized disposal site. So it is desirable to achieve a high loading of radwastes in a drum to reduce the disposal fee while meeting both the national regulations and the waste acceptance criteria of the disposal site. In general, the radioactive wastes (liquid, dried powder and sludge) were solidified by mixing with a proper binding matrix (cement, polymer, asphalt, etc.), but their solidified volume inevitably increases due to the limitation of incorporating of radwaste into a binding matrix. To solve this problem, some Korean NPPs operate both a CTS (Concentrate Treatment System, evaporation and granulation) and a polymer solidification system. The size distribution of granulated wastes produced by CTS is so broad (diameter; several μm ∼ several cm) that a polymer cannot impregnate the void space between particles due to their small size. However, if the powdered radwaste can be compacted into high density pellets, and the pellets can be loaded in a drum with maximum waste loading, then the binding matrix can fill the void between pellets, it might be more desirable to keep the size distribution of pellets constant to reduce the solidified waste volume. This compaction methodology can greatly reduce the disposal fee due to the reduction of the solidified waste volume, and can facilitate polymer solidification due to the constant size of the radwaste pellets. This methodology is also applicable to solidify powdered wastes such a depleted uranium used as a catalyst, ash and sludge. Loading radwaste compacted with bentonite pellets versus particles into a container serves, as an engineered or natural barrier in a deep geologic disposal system. Roll compaction is a typical agglomeration process for dry powders and depends on the device parameters and the material properties. This study, firstly, was focused on the design of roll compactor (briquetting machine), the shape and size of pellet, and secondly the loading method of pellets into a drum, their solidification in polymer, and evaluating the overall volume reduction. We used bentonite (particle size; 85 ∼ 100 μm) as a material to be compacted instead of radwaste powders (concentrates and depleted uranium wastes) without the addition of agglomeration agents. In the design of roll, we considered the diameter (200 mm) and width (41 mm) of roll, two types of pocket shapes (< 9 mm, 0.275 ml), and the surface of the pocket. Fig. 2 shows two pellet shapes, tetragonal and circular. The pressure of roll compactor, one of the main process variables, is > 320 kg f/cm{sup 2}, and the roll gap is 0.5 mm. The powders are compacted in a compaction zone between two counter-rotating rolls according to the complicated mechanisms. As a result of the state and the apparent density of the pellets obtained by changing the pressure from 0 to 286 kg f/cm{sup 2}, the pellets were unstable at pressure=0, but above 148 kg f/cm{sup 2} the pellets were more stable, and the apparent density of the pellets was 2.63 g/cm{sup 3} at 148 kg f/cm{sup 3}, and 2.68 g/cm{sup 3} at 286 kg f/cm{sup 2}. The roller speed (rpm) can determine the capacity (kg/h) of a compactor, and depends on both the compaction pressure and the feeding rate. By increasing the roll speed from 2 to 4 rpm, the apparent density of pellets was decreased gradually from 2.74 g/cm{sup 3} to 1.45 g/cm{sup 3}. We designed the special feeding system in order to feed powders uniformly to the roll gripping zone and to supply powders into the narrowest part of the roll gap. At a constant roll speed (3 rpm) and a constant compaction pressure (286 kg f/cm{sup 2}), the apparent density of the pellets was linearly proportional to the feeding rate from 2.18 to 2.74 g/cm{sup 3} by changing the feeding rate of powders from 8 to 12 rpm. In the polymer solidification of the obtained pellets, we used epoxy resin as a solidification agent, and showed their solidified waste forms in Fig. 5. The incorporation ratio (wt.%) of powders/polymer was about 71.7/28.3 in tetragonal pellets, 71.9/28.1 in circular pellets. We calculated the volume reduction in an aspect of powders itself and the solidified waste form. In powder case, through the comparison of the apparent density of the obtained pellets (2.74 g/cm{sup 3}) and raw powders (0.93 g/cm{sup 3}), the volume reduction was calculated as about 2.74/0.93 = 2.95 times. This means that powders can be compacted to 1/2.95 times. And in waste form case, the weight ratio of powder/polymer in a mixing method (workable) and a compaction method is about 0.42, 2.56, individually. Therefore the volume reduction was calculated as about 2.56/0.42 = 6.01 times. We found a compaction methodology for the volume reduction of powdered radioactive wastes, and their polymer solidification will be more effective to reduce the volume of radwastes to be disposed. After a characterization of the solidified waste form incorporated pellets (including sintered pellets), this methodology will be applied to treat depleted uranium wastes used as catalyst, and to solve the problem of NPPs' polymer solidification system, as mentioned above. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗