Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GAMMA FUNCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Development of a Transition Edge Sensor Gamma Ray Microcalorimeter with an Epoxy Coupled Bulk Lead Absorber

Transition edge sensor (TES)-based gamma ray detectors have been developed primarily for use up to energies of {approx}100 keV. However, there are many interesting applications at higher energies. We have started to develop a TES gamma-ray detector to apply to Positron Annihilation Spectroscopy analysis at 511 keV. Our detector is composed of a bulk lead absorber, which is coupled to a thin-film TES using a small amount of epoxy. The response of our first detector showed a very long decay tail of {approx}135 ms. To improve the device response time we have designed a new detector in which the response time is improved by a factor of five.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Compton profiles and electronic properties of TiB{sub 2}

In this paper, we report the experimental Compton profile (CP) of TiB{sub 2} using high energy {sup 137}Cs γ-rays Compton spectrometer. To interpret the experimental momentum density, we have calculated the CPs using Hartree-Fock (HF), density functional theory (DFT) and hybridization of DFT and HF within linear combination of atomic orbitals. The theoretical profile with generalized gradient approximation is found to be relatively in better agreement with the experimental profile. A sharp valley in density of states and hence the pseudogap near the Fermi energy is attributed to hybridization of Ti-3d and B-2p states and almost reverse trend of energy bands below and above the Fermi energy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

THE X-FACTOR IN GALAXIES. I. DEPENDENCE ON ENVIRONMENT AND SCALE

Characterizing the conversion factor between CO emission and column density of molecular hydrogen, X{sub CO}, is crucial in studying the gaseous content of galaxies, its evolution, and relation to star formation. In most cases the conversion factor is assumed to be close to that of giant molecular clouds (GMCs) in the Milky Way, except possibly for mergers and star-bursting galaxies. However, there are physical grounds to expect that it should also depend on the gas metallicity, surface density, and strength of the interstellar radiation field. The X{sub CO} factor may also depend on the scale on which CO emission is averaged due to effects of limited resolution. We study the dependence of X{sub CO} on gas properties and averaging scale using a model that is based on a combination of results of sub-parsec scale magnetohydrodynamic simulations and on the gas distribution from self-consistent cosmological simulations of galaxy formation. Our model predicts X{sub CO} Almost-Equal-To (2-4) Multiplication-Sign 10{sup 20} K{sup -1} cm{sup -2} km{sup -1} s, consistent with the Galactic value, for interstellar medium conditions typical for the Milky Way. For such conditions the predicted X{sub CO} varies by only a factor of two for gas surface densities in the range {Sigma}{sub H{sub 2}}{approx}50-500 M{sub sun}pc{sup -2}. However, the model also predicts that more generally on the scale of GMCs, X{sub CO} is a strong function of metallicity and depends on the column density and the interstellar UV flux. We show explicitly that neglecting these dependencies in observational estimates can strongly bias the inferred distribution of H{sub 2} column densities of molecular clouds to have a narrower and offset range compared to the true distribution. We find that when averaged on {approx}kiloparsec scales the X-factor depends only weakly on radiation field and column density, but is still a strong function of metallicity. The predicted metallicity dependence can be approximated as X{sub CO}{proportional_to}Z{sup -{gamma}} with {gamma} Almost-Equal-To 0.5-0.8.

79 ASTRONOMY AND ASTROPHYSICS↗

FRAM Version 6.1’s Bias

The Fixed-Energy Response-Function Analysis with Multiple Efficiency (FRAM) code was developed at Los Alamos National Laboratory to measure the gamma-ray spectrometry of the isotopic composition of plutonium, uranium, and other actinides. For FRAM version 4 and earlier, the reported uncertainties of the results come from the propagation of the statistics in the peak areas only. No systematic error components are included in the reported uncertainties. We did several studies with FRAM v.4 and found that FRAM’s statistical precision can be reasonably represented by its reported uncertainties. FRAM’s biases or systematic uncertainties can come from a variety of sources and can be difficult to determine. For FRAM version 5, we carefully examined the FRAM analytical results of both the archival plutonium data and the data specifically acquired for the isotopic uncertainty analysis project and found the relationship between the bias and other parameters. We then worked out the equations representing the biases of the measured isotopes from each measurement using internal spectral parameters, such as peak resolution and shape, region of analysis, and burnup (for plutonium) or enrichment (for uranium). The resulting biases were included in the reported uncertainties of FRAM v.5. For the upcoming FRAM version 6.1, we are doing the same study that we did for FRAM v.5. The resulting biases will be included in its reported uncertainties.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

FRAM Version 7.1’s Bias

The Fixed-Energy Response-Function Analysis with Multiple Efficiency (FRAM) code was developed at Los Alamos National Laboratory to measure the gamma-ray spectrometry of the isotopic composition of plutonium, uranium, and other actinides. For FRAM versions 4 and earlier, the reported uncertainties of the results come from the propagation of the statistics in the peak areas only. No systematic error components are included in the reported uncertainties. For FRAM versions 5 and 6, we examined the FRAM analytical results of both the archival plutonium data and the data specifically acquired for the isotopic uncertainty analysis project and found the relationship between the bias and other parameters. We worked out the equations representing the biases of the measured isotopes from each measurement using internal spectral parameters, such as peak resolution and shape, region of analysis, and burnup (for plutonium) or enrichment (for uranium). The resulting biases were included in the reported uncertainties of FRAM v.5 and v.6.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Determination of natural and cosmic ray induced radionuclides in Apollo 17 lunar samples

Natural and cosmic ray induced radionuclides have been determined in 15 rocks and 7 soils from the Apollo 17 mission by nondestructive gamma-ray spectroscopy. The Th and K contents of these rocks and soils are shown to be linear functions of the U contents. Large amounts of Co-56, Sc-46, and Mn-54 were found in these samples due to the large proton-accelerating flares which occurred between August 2 and 6, 1972. The behavior of the Co-56 activity as a function of the Mn-54 activity seems to be the result of variation in surface to volume ratios among the samples and exposure angle. It is not necessary to invoke an asymetric solar flare flux to explain this behavior.

Keith, J. E.↗

Measuring metamorphic history of unequilibrated ordinary chondrites

Measurements performed by a thermoluminescence sensitivity technique of the degree of metamorphism experienced by unequilibrated ordinary chondrites are reported. Samples of type 3 chondrites were ground and heated to 500 C to remove their natural thermoluminescence, then irradiated with either 50 krad from a Co-60 gamma ray source or 25 krad from a Sr-90 beta source. The resulting thermoluminescence measured as a function of temperature is found to differ as much among some type 3 chondrites as between type 3 and other types, leading to the proposal of scheme for subdividing type 3 ordinary chondrites based on their thermoluminescence sensitivity.

Sears, D. W.↗

Searches for gamma ray emission from radio pulsars

Searches were made for pulsed high energy (E 35 MeV) gamma radiation from 43 pulsars using the SAS-2 data base and radio parameters. No positive results were found, and the upper limits are consistent with the concept that gamma ray production efficiency increases with increasing apparent age. Two limits suggest that efficiency cannot be a simple function of apparent age beyond 10,000,000 years.

Thompson, D. J.↗

Searches for gamma ray emission from radio pulsars

Searches were made for pulsed high energy (E greater than 35 MeV) gamma radiation from 43 pulsars using the SAS-2 data base and radio parameters. No positive results were found, and the upper limits are consistent with the concept that gamma ray production efficiency increases with increasing apparent age. Two limits suggest that efficiency cannot be a simple function of apparent age beyond 1,000,000 years. Previously announced in STAR as N83-24463

Thompson, D. J.↗

Initial mass functions from ultraviolet stellar photometry: A comparison of Lucke and Hodge OB associations near 30 Doradus with the nearby field

UV stellar photometry is presented for 1563 stars within a 40 minutes circular field in the Large Magellanic Cloud (LMC), excluding the 10 min x 10 min field centered on R136 investigated earlier by Hill et al. (1993). Magnitudes are computed from images obtained by the Ultraviolet Imaging Telescope (UIT) in bands centered at 1615 A and 2558 A. Stellar masses and extinctions are estimated for the stars in associations using the evolutionary models of Schaerer et al. (1993), assuming the age is 4 Myr and that the local LMC extinction follows the Fitzpatrick (1985) 30 Dor extinction curve. The estimated slope of the initial mass function (IMF) for massive stars (greater than 15 solar mass) within the Lucke and Hodge (LH) associations is Gamma = -1.08 +/- 0.2. Initial masses and extinctions for stars not within LH associations are estimated assuming that the stellar age is either 4 Myr or half the stellar lifetime, whichever is larger. The estimated slope of the IMF for massive stars not within LH associations is Gamma = -1.74 +/- 0.3 (assuming continuous star formation), compared with Gamma = -1.35, and Gamma = -1.7 +/- 0.5, obtained for the Galaxy by Salpeter (1955) and Scalo (1986), respectively, and Gamma = -1.6 obtained for massive stars in the Galaxy by Garmany, Conti, & Chiosi (1982). The shallower slope of the association IMF suggests that not only is the star formation rate higher in associations, but that the local conditions favor the formation of higher mass stars there. We make no corrections for binaries or incompleteness.

Hill, Jesse K.↗

The Effect Stacking Fault Segregation and Phase Transformations have on Creep Strength in Ni-based Superalloys

In this study, two commercially similar polycrystalline Ni-based disk superalloys (LSHR and ME3) were creep tested at 760C and 552MPa to approximately 0.3% plastic strain. LSHR consistently displayed superior creep properties at this stress/temperature regime even though the microstructural characteristics between the two alloys were comparable. High resolution structural and chemical analysis, however, revealed significant differences between the two alloys among active gamma prime shearing modes involving superlattice intrinsic and extrinsic stacking faults. In ME3, Co and Cr segregation and Ni and Al depletion were observed along the intrinsic faults - revealing a gamma prime -to- gamma phase transformation. Conversely in LSHR, an alloy with a higher W content, Co and W segregation was observed along the intrinsic faults. This observation combined with scanning transmission electron microscopy (STEM) simulations confirm a gamma prime-to-D019 phase transformation along the intrinsic faults in LSHR. Using experimental observations and density functional theory calculations, a novel local phase transformation strengthening mechanism is proposed that could be further utilized to improve the high temperature creep capabilities of Ni-base disk alloys.

Superalloy↗

The X-factor in Galaxies: I. Dependence on Environment and Scale

Characterizing the conversion factor between CO emission and column density of molecular hydrogen, X{sub CO}, is crucial in studying the gaseous content of galaxies, its evolution, and relation to star formation. In most cases the conversion factor is assumed to be close to that of giant molecular clouds (GMCs) in the Milky Way, except possibly for mergers and star-bursting galaxies. However, there are physical grounds to expect that it should also depend on the gas metallicity, surface density, and strength of the interstellar radiation field. The X{sub CO} factor may also depend on the scale on which CO emission is averaged due to effects of limited resolution. We study the dependence of X{sub CO} on gas properties and averaging scale using a model that is based on a combination of results of sub-pc scale magneto-hydrodynamic simulations and on the gas distribution from self-consistent cosmological simulations of galaxy formation. Our model predicts X{sub CO} {approx} 2 - 4 x 10{sup 20} K{sup -1} cm{sup -2} km{sup -1} s, consistent with the Galactic value, for interstellar medium conditions typical for the Milky Way. For such conditions the predicted X{sub CO} varies by only a factor of two for gas surfaced densities in the range {Sigma}{sub H{sub 2}} {approx} 50-500 M{sub {circle_dot}} pc{sup -2}. However, the model also predicts that more generally on the scale of GMCs, X{sub CO} is a strong function of metallicity, and depends on the column density and the interstellar UV flux. We show explicitly that neglecting these dependencies in observational estimates can strongly bias the inferred distribution of H2 column densities of molecular clouds to have a narrower and offset range compared to the true distribution. We find that when averaged on {approx} kpc scales the X-factor depends only weakly on radiation field and column density, but is still a strong function of metallicity. The predicted metallicity dependence can be approximated as X{sub CO} {proportional_to} Z{sup -{gamma}} with {gamma} {approx} 0.5 - 0.8.

08 HYDROGEN↗

Investigating the Role of Defects in α-Pu Phase Transitions using Density Functional Theory

Before reaching its relatively low melting point of 913 K, plutonium undergoes six solid state phases: simple monoclinic alpha, body-centered monoclinic beta, face-centered orthorhombic gamma, face centered cubic delta, body-centered tetragonal delta-prime, and body-centered cubic epsilon phases. Due to their low symmetry, the monoclinic alpha and beta phases have not been studied extensively, however it has been previously hypothesized that the transition between alpha and beta is caused by defects in the lattices due to the incommensurate number of atoms. Additionally, the martensitic delta to alpha phase transformation in plutonium-gallium alloys induces an expanded alpha lattice known as alpha prime, most likely due to the insoluble gallium impurity atom. This work explores how defects such as plutonium interstitials and gallium interstitials and substitutionals may affect the alpha plutonium lattice, providing a better understanding of the mechanisms for the alpha-beta and martensitic phase transformations through density functional theory (DFT). Results indicate that plutonium interstitials within the alpha lattice induce beta features structurally and electronically, such as volume expansion and bonding changes, and gallium interstitials and substitutionals within the alpha lattice induce volume changes as observed experimentally in alpha prime.

36 MATERIALS SCIENCE↗

SU-F-J-08: Quantitative SPECT Imaging of Ra-223 in a Phantom

Purpose: Ra-223 therapy of prostate cancer bone metastases is being used to treat patients routinely. However, the absorbed dose distribution at the macroscopic and microscopic scales remains elusive, due to the inability to image the small activities injected. Accurate activity quantification through imaging is essential to calculate the absorbed dose in organs and sub-units in radiopharmaceutical therapy, enabling personalized absorbed dose-based treatment planning methodologies and more effective and optimal treatments. Methods: A 22 cm diameter by 20 cm long cylindrical phantom, containing a 3.52 cm diameter sphere, was used. A total of 2.01 MBq of Ra-223 was placed in the phantom with 177.6 kBq in the sphere. Images were acquired on a dual-head Siemens Symbia T16 gamma camera using three 20% full-width energy windows and centered at 84, 154, and 269 keV (120 projections, 360° rotation, 45 s per view). We have implemented reconstruction of Ra-223 SPECT projections using OS-EM (up to 20 iterations of 10 subsets) with compensation for attenuation using CT-based attenuation maps, collimator-detector response (CDR) (including septal penetration, scatter and Pb x-ray modeling), and scatter in the patient using the effective source scatter estimation (ESSE) method. The CDR functions and scatter kernels required for ESSE were computed using the SIMIND MC simulation code. All Ra-223 photon emissions as well as gamma rays from the daughters Rn-219 and Bi-211 were modeled. Results: The sensitivity of the camera in the three combined windows was 107.3 cps/MBq. The visual quality of the SPECT images was reasonably good and the activity in the sphere was 27% smaller than the true activity. This underestimation is likely due to partial volume effect. Conclusion: Absolute quantitative Ra-223 SPECT imaging is achievable with careful attention to compensate for image degrading factors and system calibration.

60 APPLIED LIFE SCIENCES↗

Modeled Martian subsurface elemental composition measurements with the Probing In situ with Neutron and Gamma ray instrument: Gamma and Neutron Measurements on Mars

Here, the Probing In situ with Neutrons and Gamma rays (PING) instrument is an innovative application of active neutron-induced gamma-ray technology. The objective of PING is to measure the elemental composition of the Martian regolith. As part 2 of a two-part submission, this manuscript presents PING's sensitivities as a function of the Martian regolith depth and PING's uncertainties in the measurements as a function of observation time in passive and active mode. Part 1 of our submission models the associated regolith types. The modeled sensitivities show that in PING's active mode, where both a Pulsed Neutron Generator (PNG) and a Gamma-Ray Spectrometer (GRS) are used, PING can interrogate the material below the rover to about 20 cm due to the penetrating nature of the high-energy neutrons and the resulting secondary gamma rays observed with the GRS. PING is capable of identifying most major and minor rock-forming elements, including H, O, Na, Mn, Mg, Al, Si, P, S, Cl, Cr, K, Ca, Ti, Fe and Th. The modeled uncertainties show that PING's use of a PNG reduces the required observation times by an order of magnitude over a passive operating mode where the PNG is turned off. While the active mode allows for more complete elemental inventories with higher sensitivity, the gamma-ray signatures of some elements are strong enough to detect in passive mode. We show that PING can detect changes in key marker elements and make thermal neutron measurements in about 1 minute that are sensitive to H and Cl.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Free-moving Quantitative Gamma-ray Imaging

The ability to map and estimate the activity of radiological source distributions in unknown three-dimensional environments has applications in the prevention and response to radiological accidents or threats as well as the enforcement and verification of international nuclear non-proliferation agreements. Such a capability requires well-characterized detector response functions, accurate time-dependent detector position and orientation data, a digitized representation of the surrounding 3D environment, and appropriate image reconstruction and uncertainty quantification methods. We have previously demonstrated 3D mapping of gamma-ray emitters with free-moving detector systems on a relative intensity scale using a technique called Scene Data Fusion (SDF). Here we characterize the detector response of a multi-element gamma-ray imaging system using experimentally benchmarked Monte Carlo simulations and perform 3D mapping on an absolute intensity scale. We present experimental reconstruction results from hand-carried and airborne measurements with point-like and distributed sources in known configurations, demonstrating quantitative SDF in complex 3D environments.

47 OTHER INSTRUMENTATION↗