Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Development of Sn-Ag-Cu-X Solders for Electronic Assembly by Micro-Alloying with Al

Of Pb-free solder choices, an array of solder alloys based on the Sn-Ag-Cu (SAC) ternary eutectic (T eut = 217°C) composition have emerged with potential for broad use, including ball grid array (BGA) joints that cool slowly. This work investigated minor substitutional additions of Al (<0.25 wt.%) to Sn-3.5Ag-0.95Cu (SAC3595) solders to promote more consistent solder joint microstructures and to avoid deleterious product phases, e.g., Ag3Sn “blades,” for BGA cooling rates, since such Al additions to SAC had already demonstrated excellent thermal aging stability. Consistent with past work, blade formation was suppressed for increased Al content (>0.05Al), but the suppression effect faded for >0.20Al. Undercooling suppression did not correlate specifically with blade suppression since it became significant at 0.10Al and increased continuously with greater Al to 0.25Al. Surprisingly, an intermediate range of Al content (0.10 wt.% to 0.20 wt.% Al) promoted formation of significant populations of 2-μm to 5-μm faceted Cu-Al particles, identified as Cu33Al17, that clustered at the top of the solder joint matrix and exhibited extraordinary hardness. Clustering of Cu33Al17 was attributed to its buoyancy, from a lower density than Sn liquid, and its early position in the nucleation sequence within the solder matrix, permitting unrestricted migration to the top interface. Joint microstructures and implications for the full nucleation sequence for these SAC + Al solder joints are discussed, along with possible benefits from the clustered particles for improved thermal cycling resistance.

36 MATERIALS SCIENCE↗

Microstructure and Sn crystal orientation evolution in Sn-3.5Ag lead-free solders in high temperature packaging applications

Understanding the reliability of eutectic Sn-3.5Ag lead-free solders in high temperature packaging applications is of significant interest in power electronics for the next generation electric grid. Large area (2.5mm 2.5mm) Sn-3.5Ag solder joints between silicon dies and direct bonded copper substrates were thermally cycled between 5 C and 200 C. Sn crystal orientation and microstructure evolution during thermal cycling were characterized by electron backscatter diffraction (EBSD) in scanning electron microscope (SEM). Comparisons are made between observed initial texture and microstructure and its evolution during thermal cycling. Gradual lattice rotation and grain boundary misorientation evolution suggested the continuous recrystallization mechanism. Recrystallization behavior was correlated with dislocation slip activities.

high temperature packaging↗

Microstructural Characterization, Mechanical Properties, and Corrosion Resistance of Dental Co-Cr-Mo-W Alloys Manufactured by Selective Laser Melting

In this paper, the microstructure, mechanical properties, and corrosion resistance of the dental Co-Cr-Mo-W alloys fabricated by selective laser melting (SLM) were systematically investigated and correlated. The microstructure of the SLM group (SG) specimens is composed of extremely fine columnar crystals, exhibiting supersaturated and homogeneous character. The matrix mainly consists of face-centered-cubic (FCC) cobalt solid solutions, and minimal hexagonal-close-packed (HCP) cobalt solid solutions. Mechanical test results showed that the 0.2% yield strength of SG was 775 ± 7 MPa, and the ultimate tensile strength was 1118 ± 25 MPa. The elongation of SG was 8.28 ± 0.4%, and the microhardness of SG was 476 ± 10 HV. All of these values largely exceeded the cast group (CG) specimens. The high strength is attributed to their fine columnar crystals and supersaturated matrices. The fewer content from the HCP phase and a lack of intermetallic compounds or eutectic contribute to the high ductility. Furthermore, a higher E{sub corr}, lower I{sub corr} were acquired for better corrosion resistance compared to cast specimens, due to even less composition segregation and more microstructural homogeneity.

36 MATERIALS SCIENCE↗

A Low-Cost Lightweight Entropic Alloy with High Strength

In this study, a series of lightweight Al–Mg system entropic alloys containing Zn, Cu, and Si were designed based on the order/disorder or entropy, and eutectic concepts. The alloys of Al{sub 58.5}Mg{sub 31.5}Zn{sub 4.5}Cu{sub 4.5}Si{sub 1}; Al{sub 63}Mg{sub 27}Zn{sub 4.5}Cu{sub 4.5}Si{sub 1}; Al{sub 66.7}Mg{sub 23.3}Zn{sub 4.5}Cu{sub 4.5}Si{sub 1}; Al{sub 80}Mg{sub 14}Zn{sub 2.7}Cu{sub 2.7}Si{sub 0.6}; Al{sub 85}Mg{sub 10.5}Zn{sub 2.025}Cu{sub 2.025}Si{sub 0.45}; and Al{sub 90}Mg{sub 7}Zn{sub 1.35}Cu{sub 1.35}Si{sub 0.3} were prepared by induction melting under a high-purity argon atmosphere and then casted into stainless steel molds. The microstructures which were tested in the as-cast state exhibited multiphases and contained apparent volume fractions of intermetallic compounds and solid solutions. Then, the compressive mechanical properties of the alloys were measured, and high fracture strengths of 577, 677, 590, 498, 814, and 794 MPa, respectively, were determined. Strong hardening phenomena were observed in the Al{sub 80}Mg{sub 14}Zn{sub 2.7}Cu{sub 2.7}Si{sub 0.6}, Al{sub 85}Mg{sub 10.5}Zn{sub 2.025}Cu{sub 2.025}Si{sub 0.45}, and Al{sub 90}Mg{sub 7}Zn{sub 1.35}Cu{sub 1.35}Si{sub 0.3} alloys at room temperature, with amazing plasticity percentages of 13.8, 24.8, and 32.7%, respectively. The property differences in the lightweight alloys were analyzed using the following parameters: the critical values of the enthalpy of mixing; atomic size differences; ratio of entropy to enthalpy; valence electron concentration (VEC); and Pauling electronegativity difference. Finally, three of the aforementioned parameters (atomic size difference, enthalpy of mixing, and Pauling electronegativity difference) were regarded in this study as the crucial rules for the lightweight multicomponent alloys.

36 MATERIALS SCIENCE↗

Solidification Characteristics of Silicon-Alloyed Ductile Cast Irons

Solidification pattern of three ductile iron compositions [I-2.5%Si; II-4%Si, and III-4%Si-1.6%Mo] is studied, to evaluate the effects of high Si and Mo contents. Inoculation compensates for the negative effect of Mo on eutectic undercooling. The deviation using a sphere as reference of graphite particles is noticeably increased by silicon alloying, when a characteristic of the graphite particles appears have a larger perimeter, resulting in a large category [IV, V and VI forms, ISO 945]. The sphericity shape factor (SSF) considering the real perimeter of particle is recommended in the nodularity evaluation in high-Si ductile iron, instead of the roundness shape factor, involving maximum ferret, presently incorporated in the ISO 945 standard. The higher the minimum acceptable SSF is, the greater difference in nodularity, between conventional and Si-alloyed ductile irons. For more than 4%Si, ductile irons are characterized by a medium-quality graphite phase, with prevalent form V-ISO 945 graphite. A specific inoculant, with a powerful action on the graphite particle compactness, especially to promote VI graphite form, is necessary.

36 MATERIALS SCIENCE↗

Brazing of Martensitic Stainless Steel to Copper Using Electroplated Copper and Silver Coatings

Brazing of 3 mm thick sheets of low-carbon martensitic stainless steel and Cu-Cr-Zr-Ti alloy was attempted using electroplated coatings of Cu and Ag. Ni coating of 5 µm thick was provided on the MSS base metal to enhance the wettability. Brazing experiments were carried out at 985 °C for a holding of 15 min. Detailed microstructural studies, hardness, lap-shear, tensile, and pressure tests were carried out on the brazed joints. The reaction between the Cu and Ag coatings lead to the formation of in situ braze metal. The microstructure of the braze metal was found to consist of Cu-rich primary alpha (α{sub P}) and Ag-rich eutectic mixture (β + α{sub E}). In lap-shear tests, the brazed joints produced with an overlap of 9 and 6 mm were found to fail in copper base metal, while the joints produced with an overlap of 3 mm failed in the braze metal exhibiting a lap-shear strength of 147 MPa. In tensile tests, the butt brazed joints were found to fail in copper base metal as well with an average tensile strength of 213 MPa. The braze metal hardness was found to be higher than the hardness of the copper base metal. In pressure tests, the brazed panels were found to survive a pressure of 750 bar without undergoing any damage. These results show that electroplated coatings of Cu and Ag can be advantageously utilized for brazing of large, complex-shaped parts such as thrust chambers in space industry.

36 MATERIALS SCIENCE↗

Influence of Melt-Pouring Temperature and Composition of Primary Coating of Shell Mold on Tensile Strength and Creep Resistance of Ni-Based Superalloy

Eight investment castings of Inconel 713C superalloy were fabricated, varying in the melt-pouring temperature, from 1400 to 1520 °C, and CoAl{sub 2}O{sub 4} inoculant content, 0 or 5 wt.%, in the primary coat. Their influence on grain size on tensile and creep properties was investigated. The best combination of yield stress (815 MPa) and elongation (A{sub 4} = 7.65%) at ambient temperature was obtained in surface-modified castings poured from 1520 °C. The longest time to rupture was for the unmodified castings (76.8 h) poured from 1520 °C, while for the modified variant, the time to rupture was lower around, 7.4 h, which was still a satisfactory value. During tensile testing, microcracks were formed in large eutectic γ′, carbides and borides, due to the accumulation of stress at interfaces with the matrix. During creep, N-type rafting of γ′ precipitates and phase transformation MC + γ → γ′ + M{sub 23}C{sub 6} took place.

36 MATERIALS SCIENCE↗

Effect of Ti Modification on Microstructures and Properties of Carbidic Austempered Ductile Iron

In this paper, we investigated the effect of titanium modification on microstructures and properties of carbidic austempered ductile iron (CADI) containing 3.72 wt.% C, 2.77 wt.% Si, and 0.51 wt.% Mn. The results showed that with the addition of 0.1 wt.% Ti, TiC particles were formed, and distributed in carbides and matrix. Microstructural observation indicated that the maximum diameter of graphite nodules decreased from 58 to 40 μm, and the shape of carbides transformed from network to fragmentation, which was related to the nucleation of the eutectic structure (γ + (Fe, Cr){sub 3}C) where TiC particles act as the nucleus. After isothermal quenching at 300 °C, the hardness of Ti-bearing CADI was 3.5 HRC higher than ordinary CADI, and the impact toughness was increased by 14.3%. Additionally, due to the decrease in exfoliation, the wear loss of Ti-bearing CADI was 14.8% lower than ordinary CADI during the block-on-ring wear test at the surface load of 300 N.

36 MATERIALS SCIENCE↗

Effects of Laser Fluence on Microstructure and Bonding Characteristics of Wideband Laser-Deposited Nickel Composite Coatings

The wideband laser has shown great potential in metal–ceramic coatings deposition due to the high efficiency and low dilution rate. However, the effects of wideband laser process on microstructure evolution and bonding mechanism at the coatings/substrate interface are still a critical problem and need further investigation. In this work, nickel composite coatings are fabricated on the surface high-strength low-alloy steel. The effects of laser fluence on microstructure evolution, shear strength and fracture mechanism are studied. Results indicated the added WC particles were partly dissolved due to the high-power laser irradiation. Many block precipitates and dense eutectic were synthesized in composite coatings. Reinforced phases mainly consist of Cr{sub 5}B{sub 3}, Cr{sub 23}C{sub 6}, W{sub 2}C and Cr{sub 3}Ni{sub 2}. The dilution of Q550 steel contributed to the formation of nickel dendrites and facilitated a dense metallurgical bonding at coating/substrate interface when laser fluence was high. Shear strength tests indicated the laser fluence and shear strength had a positive correlation. For Ni60/WC composite coatings designed in these experiments, the recommend laser fluence should be higher than 55 J/mm{sup 2}, above which the shear strength could be greater than 200 MPa. Fracture surfaces indicated the failure mechanism of composite coatings was quasi-cleavage fracture.

36 MATERIALS SCIENCE↗

Effects of Bi-Sb Addition and Solution Treatment on Microstructures and Mechanical Properties of Al-20 wt.% Mg{sub 2}Si Composites

In this study, the effects of compound modification with Bi and Sb and solution treatment on the microstructures evolution and the mechanical properties of Al-20 wt.% Mg{sub 2}Si composites were investigated. The specimens were observed by optical microscope, scanning electron microscope equipped with an energy-dispersive spectrometer and x-ray diffraction. The characterization results showed that 2.0 wt.% Sb and 0.2 wt.% Bi addition refined the primary Mg{sub 2}Si from 95 to 10 μm, accompanied by a change in morphology from coarse dendrites to dispersive fine polygons. After solution treatment at 540 °C for 15 h, the sharp polygonal primary Mg{sub 2}Si particles were blunted and the flake-like eutectic Mg{sub 2}Si phases were changed to small spherical particles, resulting in the increase in the Brinell hardness of the composites from HB 94.53 to 134.67. Mechanical tests revealed that both tensile strength and hardness of the composite were improved by compound modification with Bi and Sb, and the ultimate tensile strength (UTS) was increased from 216 MPa unmodified to 257 MPa with optimum modification of 2 wt.% Sb and 0.2 wt.% Bi. A propounded change in hardness from HB 94.53 to 130.67 was also investigated.

36 MATERIALS SCIENCE↗

The Influence of Shell Mold Composition on the As-cast Macro- and Micro-structure of Thin-Walled IN713C Superalloy Castings

In the investment casting process, the building of ceramic layers around the wax pattern is the main time-consuming stage. Increasing their number ensures sufficient mechanical properties, but also lengthens the whole process, including drying time and preheating of the mold. Four molds for casting Ni-based superalloy IN713C were strengthened by glass fibers, included in the slurry, and metal powder, of Al, Cu, Fe or Ni, in the coverage. Castings were subjected to microstructural investigations in order to find out if the new design can be promising for the manufacture of jet engine components. Bend tests revealed that the green strengths of all new molds were higher, at least 3.65 MPa, than that of the unmodified molds, 3.0 MPa. Optical microscopy revealed that the composition of a mold had a strong influence on stereological parameters of equiaxed IN713C grains. Microstructural observation and hardness measurements of castings revealed differences in the volume fraction of strengthening phases, porosity and hardness. The microstructure due to the complex chemical composition of IN713C consisted of several phases including ternary eutectics as a consequence of L → γ + Ni{sub 7}Zr{sub 2} + (Nb, Zr)C.

36 MATERIALS SCIENCE↗

Effects of Transition Layer on Bending Resistance in Copper-Clad Aluminum Composite Casting

The performance of the transition layer in a Cu/Al composite casting directly affects the quality of subsequent plastic deformation processing; however, there are no universal or standardized measurement indices for the performance of the transition layer. In this study, Cu/Al composite castings were prepared using the pouring aluminum method, and the resulting solidification microstructures on the bending resistance were investigated. The results of this study lay a theoretical foundation for the development of the plastic processing technologies of these composite castings. A thinner transition layer in the Cu/Al composite casting led to improved bending resistance. In addition, for a fixed total thickness of the transition layer, the bending resistance was mainly controlled by the γ/β interface and β + eutectic (α + β) microstructure, and the thickness of the γ phase had a negligible effect on the bending resistance. The γ/β interface cracked first when the transition layer bore the tensile and shear stress during the bending process, which resulted in the transition layer easily separating from the copper. The bending resistance of the transition layer can be feasibly judged by measuring the bending angle of the specimen tip, which can be easily performed when the specimen bends toward the aluminum direction, suggesting that our proposed method has considerable practical significance.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of a SiO{sub 2} Ceramic and TC4 Alloy Joint Brazed with a Nanocomposite Filler

Vacuum brazing of TC4 alloy and SiO{sub 2} ceramic was achieved using a nano-AgCuNi braze alloy. The melting temperature of nano-AgCu powders was analyzed by differential scanning calorimeter. Furthermore, the effects of the Ni content on the microstructure and mechanical properties of the joints were studied. The results showed that the melting temperature of the nano-AgCu filler was 774 °C. A decrease in the melting temperature of 6 °C was observed, compared with the general AgCu filler, and this decrease enabled the interfacial reaction of the joint to begin earlier. The typical interfacial microstructure of the TC4/nano-AgCuNi/SiO{sub 2} ceramic joint brazed at 950 °C for 10 min was TC4/α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectoid structure/Ti{sub 2}(Cu,Ni) compound with α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure/Ti{sub 4}O{sub 7} + TiSi{sub 2}/SiO{sub 2} ceramics. The homogeneous microstructure of α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectoid structure primarily existed in the diffusion layer. Additionally, the refined α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure created via a eutectic reaction and Ti{sub 2}(Cu,Ni) compound was distributed in the brazing seam. The Ni content could influence the formation of Ti-Cu-Ni ternary intermetallic compounds (IMCs). An increase in Ni led to an increase in the α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure in the brazing seam. The shear strength of the brazed joints first increased and then decreased with the increase in the nano-Ni content, and the optimal shear strength of 30.1 MPa was achieved at 10 wt.% Ni. The increase in the α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure and the decrease in brittle compounds enhanced the shear strength of the joint. Fracture analysis of the joints brazed at 950 °C for 10 min indicated that the cracks mainly occurred in SiO{sub 2} ceramic.

36 MATERIALS SCIENCE↗

Microstructure Evolution, Structural Integrity, and Hot Corrosion Performance of Nitrogen-Enhanced Stainless Steel Welds

This work articulated the multi-pass, gas tungsten arc welding by adopting pulsating current for joining nitrogen-enhanced, low-carbon austenitic stainless steel, AISI 316L(N). An austeno-ferrite stainless steel (ER2594) and an over-alloyed (ERNiCrMo-3) fillers were employed to join 6-mm-thick plates of AISI 316L(N). Acicular and lathy ferrite in the weld zone of ER2594 and the occurrence of secondary phases in the fusion zone of over-alloyed filler were observed. The notch tensile strength data attested that the joint strength was greater for the welds employing an over-alloyed filler. This study also affirms that the welds obtained with ER2594 filler resulted in better impact toughness (144 J) compared with ERNiCrMo-3 filler and base metal. Also the notch impact toughness of ER2594 weldment is increased to 60% in comparison with that of candidate metal. Corrosion studies were also performed by exposing the coupons in a eutectic salt mixture comprising of 40%K{sub 2}SO{sub 4}-60%NaCl for 50 cycles at 650 °C. It is observed that the weld zone employing over-alloyed filler experienced better high-temperature corrosion resistance compared to the base metal. The specific results of this investigation will be of greater demand to the nuclear and marine applications utilizing these joints.

36 MATERIALS SCIENCE↗

Effect of Chromium Content on Microstructure, Hardness, and Wear Resistance of As-Cast Fe-Cr-B Alloy

The effects of chromium content on microstructure, hardness and wear resistance of as-cast Fe-xCr-1.0B (x = 0, 4, 8, 12, 16, 20) alloys were investigated by means of optical microscope (OM), scanning electron microscope (SEM), x-ray diffractometer (XRD), hardness tester and ring block wear tester. The results showed that the microstructures of chromium-free alloy were mainly composed of pearlite, ferrite, and eutectic borocarbides, and the hardness was very low, only 18.8 HRC. With the increase in chromium content, the matrix of as-cast Fe-Cr-B alloy gradually began to transform from pearlite and ferrite to lath martensite, and the type of borocarbides changed from Fe{sub 2}(B, C) to M{sub 2}(B, C), M{sub 7}(C, B){sub 3} and M{sub 23}(C, B){sub 6} (M = Fe, Cr). When the chromium content was 12 wt.%, the hardness of alloy reached the highest value of 61.1 HRC, and the wear resistance of alloy was the best. The results of worn surface analysis showed that the wear failure of as-cast Fe-Cr-B alloy was mainly caused by multiple plastic deformation and micro-cutting.

36 MATERIALS SCIENCE↗

Laser Weldability of AlSi{sub 10}Mg Alloy Produced by Selective Laser Melting: Microstructure and Mechanical Behavior

Selective laser melting (SLM) allows 3D complex parts to be produced with integrated functionalities but does not permit to realize large dimension parts, as the building chamber volume of commercial SLM systems is limited. Therefore, the possibility of joining SLM-built parts by welding appears as extremely valuable. In this work, laser weldability of SLMed AlSi{sub 10}Mg parts has been investigated. The cooling rates induced by the welding process are lower than the ones of SLM; therefore, typical eutectic silicon network of SLM-built parts appears broken in both the melted zone and part of the heat-affected zone, as confirmed by calorimetric measurement. This microstructural evolution caused a local decrease of hardness from 132 HV to 73 HV and a reduction of ductility caused by porosity formation in the weld bead. Moreover, the thermal treatment, performed at 320°C, can limit the gap of tensile response among welded bead and base SLM material.

36 MATERIALS SCIENCE↗

Improved High-Temperature Aluminum Alloys Containing Cerium

A common rare earth (cerium) when added to aluminum in compositions up to the eutectic compositions of around 10 wt.% improves the high-temperature performance of aluminum alloys. In the early 1980s, some promising research and development efforts focused on powder metallurgy revealed that aluminum alloys containing 4 wt.% cerium exhibit high-temperature mechanical properties exceeding those of the best commercial aluminum casting alloys then in production. Those compositions, which also included high levels of iron, were difficult to process. Recently, magnesium replaces iron to reduce density and improve processing. Cerium oxide is an abundant rare earth oxide that is often discarded during the refining of more valuable rare earths such as Nd and Dy. Therefore, the economics are compelling for cerium as an alloy additive. In this review, we report results obtained during an investigation of the processing and properties of aluminum-cerium alloys produced via casting, extrusion and additive manufacturing. The results show mechanical properties are retained at higher temperatures than other aluminum alloys and show complete recovery of mechanical properties at room temperature when exposed to elevated temperatures as high as 500 °C for 1000 h. Alloys containing cerium also have superior corrosion properties when compared to most aluminum alloys.

36 MATERIALS SCIENCE↗

Characterization of an aluminum alloy hemispherical shell fabricated via direct metal laser melting

The ability of additive manufacturing to directly fabricate complex shapes provides characterization challenges for part qualification. The orientation of the microstructures produced by these processes will change relative to the surface normal of a complex part. In this work, the microscopy and x-ray tomography of an AlSi10Mg alloy hemispherical shell fabricated using powder bed metal additive manufacturing are used to illustrate some of these challenges. The shell was manufactured using an EOS M280 system in combination with EOS-specified powder and process parameters. The layer-by-layer process of building the shell with the powder bed additive manufacturing approach results in a position-dependent microstructure that continuously changes its orientation relative to the shell surface normal. X-ray tomography was utilized to examine the position-dependent size and distribution of porosity and surface roughness in the 98.6% dense part. Optical and electron microscopy were used to identify global and local position-dependent structures, grain morphologies, chemistry, and precipitate sizes and distributions. The rapid solidification processes within the fusion zone (FZ) after the laser transit results in a small dendrite size. Cell spacings taken from the structure in the middle of the FZ were used with published relationships to estimate a cooling rate of ~9 × 10 5 K/s. Uniformly-distributed, nanoscale Si precipitates were found within the primary α-Al grains. A thin, distinct boundary layer containing larger α-Al grains and extended regions of the nanocrystalline divorced eutectic material surrounds the FZ. Moreover, subtle differences in the composition between the latter layer and the interior of the FZ were noted with scanning transmission electron microscopy (STEM) spectral imaging.

36 MATERIALS SCIENCE↗