Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Content Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Flowability of Crumbler Rotary Shear Size-Reduced Granular Biomass: An Experiment-Informed Modeling Study on the Angle of Repose

Biomass has potential as a carbon-neutral alternative to petroleum for chemical and energy products. However, complete replacement of fossil fuel is contingent upon efficient processes to eliminate undesirable characteristics of biomass, e.g., low bulk density, variability, and storage-induced quality problems. Mechanical size reduction via comminution is a processing operation to engineer favorable biomass flowability in handling. Crumbler rotary shear mill has been empirically demonstrated to produce more uniformly shaped particles with higher flowability than hammermilled biomass. This study combines modeling and experimentation to unveil fundamental understandings of the relation between granular particle characteristics and biomass flow behavior, which elucidate underlying mechanisms and guide selection of critical processing parameters. For this purpose, the impact of critical material attributes, including particle size (2–6 mm), particle shape (briquette, chip, clumped-sphere, cube, etc.), and surface roughness, on the angle of repose (AOR) of milled pine chips were investigated using discrete element method (DEM) simulations. Forest Concepts Crumbler rotary shear system is used to produce milled pine particles within the same size range considered in DEM simulations. AOR of different sets of these particles were measured experimentally to benchmark DEM results against experimental data. Specific energy consumption for the comminution of biomass with different particle size and moisture content are measured for technoeconomic analysis. Our results show that the smaller size (2 mm) of pine particle achieves better followability (i.e., smaller AOR) while the energy cost of comminution is significantly higher and bulk density is almost the same as the 6-mm pine particles. For the 2-mm particle size, Crumbles from veneer have better flow properties than Crumbles from chips. Contrarily, no significant difference was observed between the AOR of the two materials for the 6-mm particle size. Furthermore, from DEM simulations, mechanical interlocking between particles was found as a dominant factor in determining AOR of complex-shaped particles such as milled pine, which cannot be accurately captured by using simple particle shapes (e.g., mono-sphere) with a rolling resistance model. Conversely, clumped-sphere model alleviates this limitation without increasing computational cost significantly and can be used for accurate representation of biomass granular particles when simulating free-flow behavior.

09 BIOMASS FUELS↗
DOE OSTI2026

Data From: "Warming and snow loss increase reliance on old groundwater in a Colorado River headwater"

This repository contains the data and code associated with the paper titled "Warming and snow loss increase reliance on old groundwater in a Colorado River headwater," published in Nature Geoscience, 2026. This study seeks to answer how various ages of groundwater interact with mountainous streamflow in mountainous headwaters such as the East River. It includes various model-data processing scripts, primarily for ParFlow-CLM analysis of simulated water years 2015-2021, and two numerical warming experiments (+2.5 and +4.0 degrees C), including run scripts, forcing scripts, and post-processing, as well as comparison to observation datasets, detailed below. This data requires the use of R (.r, .rmd), Python (.py), Jupyter Notebook or Jupyter Lab (.ipynb), ParFLOW-CLM, EcoSLIM. Further information on the use of all file formats mentioned below (e.g. .tff. .nc) are provided within the associated scripts and directory where the files are located. Contents & Usage ASO/: ​​Contains the bash and python scripts used to convert airborne snow observatory (ASO) data (ASO, 2023) in various data formats (georeferenced tiff file, NetCDF, UTM, and to latitude/longitude) then regrided to the ParFlow equivalent grid. Output data are in regrid_regll_data.zip and subsequently visualized and analyzed in plot_and_compare.py for Supplementary Figures A14 and A15. The wksht_ASO_comparison.xlsx spreadsheet is used to calculate the data for Supplementary Figure A16. EcoSLIM/: Contains the scripts and input files to run the EcoSLIM particle tracking simulations (/run_scripts) and the post-processing python script (/plot_scripts/eco_agedist_plots.ipynb). Jasechko et al./: Contains the jupyter notebook (Extract_Elevation.ipynb) to determine the outlet elevations of the 260 watersheds used in Jasechko et al. (2016), and the corresponding table, Table_S1_Watersheds_alt.csv. Used to create Supplementary Information Figure A2. PLM_Wells/: Contains the QA/QC-ed groundwater level time series of the PLM-1 and PLM-6 Monitoring Wells from Faybishenko et al. (2023), reformatted to water years used for Supplementary Figures A19 and and A20. ParFlow/: Contains the input files and run scripts to run ParFlow-CLM (/run_scripts), the python and tool command language (Tcl) scripts to create and distribute the ParFlow forcing simulation files (/forcing), and various scripts and intermediary files to analyze the model outputs (/post_process). SQUIRE/: Contains the processing scripts and intermediary files for the Surface QUantitatIve pRecipitation Estimation (SQUIRE) data (Grover, 2023) used to generate Supplementary Figure A18. USGS_Streamflow/: Contains the raw and gap-filled United States Geological Survey streamflow data (U.S. Geological Survey, 2026) used at the Almont station (site number 09112500). Gap-filling is performed in the R script with data from the Taylor station (site number 09110000). (/USGS_09112500_EAST_RIVER_AT_ALMONT_GAP_FILLED/code_almont_streamflow_gap_fill.Rmd). discharge/: Contains the gap-filled discharge data at the Watershed Function SFA East River pumphouse site (Newcomer et al., 2022) used to generate Supplementary Figure A13 and to compute hourly Nash-Sutcliffe model efficiency coefficients (NSE) in Table A4. snotel_and_flux_tower/: Contains the snow telemetry data (U.S. Department of Agriculture, 2024) from the Butte (site ID 380) and Schofield (site ID 737) stations, reformatted by water year, accessed with the snotelr R package. Used to create Supplementary Figure A17. Also contains the flux tower observational data (FluxTower_Pumphouse_ESS-DIVE.ET_only.h.txt) from Ryken et al. (2022) and sap flux transpiration data (MaxB_Transpiration_5Sites.daily_sums.h.txt) from Ryken (2021), used to create Supplementary Figures A22 and A23, respectively. Raw EcoSLIM model outputs are in excess of 24TB, and are stored on National Energy Research Scientific Computing Center (NERSC) and publicly available via the external link provided in the paper.

atmospheric warming↗
DOE OSTI2022

New Lightning-Derived Vertical Total Electron Content Data Provide Unique Global Ionospheric Measurements

A newly released, novel ionospheric data set of global gridded vertical total electron content (VTEC) is introduced in this paper. This VTEC data set, provided by Los Alamos National Laboratory (LANL), is derived from very high frequency (VHF; defined as 30–300 MHz) broadband radio-frequency (RF) measurements of lightning made by U.S. Department of Defense sensing systems on board Global Positioning System (GPS) satellites. This paper presents the new data set (LANL VTEC), discusses the errors inherent in VHF TEC estimation due to ionospheric dispersion, and compares the LANL VTEC to two community standard VTEC gridded products: Jet Propulsion Laboratory's Global Ionospheric Model (JPL GIM) and the CEDAR community's Open Madrigal VTEC gridded measurements of L-band GNSS (global navigation satellite systems) TEC. We find that the LANL VTEC data have an offset of 3 TECU from CEDAR Madrigal GNSS VTEC and a full-width-half-maximum (FWHM) of 6 TECU. In comparison, the offset between LANL VTEC and the JPL GIM model is –3 TECU, but with a FWHM of 5 TECU. We also compare to Jason-3 VTEC measurements over the ocean, finding an offset of less than 0.5 TECU and an FWHM of <5 TECU. Because this technique uses a completely different methodology to determine TEC, the sources of errors are distinct from the typical ground-based GNSS L-band (GHz) TEC measurements. Also, because it is derived from RF lightning signals, this data set provides measurements in regions that are not well covered by ground-based GPS measurements, such as over oceans and over central Africa.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Molten‐Salt‐Mediated Chemical Looping Oxidative Dehydrogenation of Ethane with In‐Situ Carbon Capture and Utilization

Abstract The molten‐salt‐mediated oxidative dehydrogenation (MM‐ODH) of ethane (C 2 H 6 ) via a chemical looping scheme represents an effective carbon capture and utilization (CCU) method for the valorization of ethane‐rich shale gas and concurrent mitigation of carbon dioxide (CO 2 ) emissions. Here, stepwise experimentation with Li 2 CO 3 ‐Na 2 CO 3 ‐K 2 CO 3 (LNK) ternary salts (i) assessed how each component of the LNK mixture impacted ethane MM‐ODH performance and (ii) explored physicochemical and thermodynamic mechanisms behind melt‐induced changes to ethylene (C 2 H 4 ) and carbon monoxide (CO) yields. Of fifteen screened LNK compositions, nine exhibited ethylene yields greater than 50 % at 800 °C while maintaining C 2 H 4 selectivities of 85 % or higher. LNK salts rich in Li 2 CO 3 content yielded more ethylene and CO on average than their counterparts, and net CO 2 capture per cycle reached a maximum of ~75 %. Extended MM‐ODH cycling also demonstrated long‐term stability of a high‐performing LNK medium. Density functional theory (DFT) calculations andab initiomolecular dynamics (AIMD) simulations suggested that the molten salt does not directly activate C 2 H 6 . Meanwhile, an empirical model informed by experimental data and reaction thermodynamics adequately predicted overall MM‐ODH performance from LNK composition and provided insights into the system′s primary drivers.

Chemistry↗
DOE OSTI2026

Online LIBS–ML Framework for Dynamic Characterization of Heterogeneous Waste-Derived Gasification Feedstocks

LIBS−ML framework for real time feedstock characterization during continuous conveyor transport Heterogeneous waste derived feedstocks (e.g., waste coal, biomass and blends) introduce rapid variability in heating value and ash chemistry that affect gasifier operation, yet conventional laboratory characterization techniques are too slow to support proactive control. To address this gap, this study reports on an online, in situ, dynamic characterization framework that couple’s laser-induced breakdown spectroscopy (LIBS) with leakage safe machine learning (ML) regression to deliver real time, decision quality predictions of gasifier relevant properties. A controlled sample matrix spanning two different waste coals, two different biomasses, and engineered blends under two particle size conditions were constructed and benchmarked using standardized laboratory analyses for proximate/ultimate properties and ash composition. LIBS spectra were acquired dynamically as material flowed on a conveyor belt, using high energy 1064 nm laser ablation and shot averaging to improve repeatability and precision. Supervised regression models (multi layer perceptron (MLP) /artificial neural network (ANN), random forest (RF), and support vector regression (SVR)) and an optimized weighted ensemble were trained on emission line feature sets using nested cross validation with Bayesian hyperparameter tuning and validated against an independent hold out set. The proposed LIBS−ML workflow achieves near laboratory predictive fidelity across parametric targets (including higher heating value (HHV), ash content, fixed carbon, sulfur, major ash forming oxides, and initial deformation temperature (IDT)), with the weighted ensemble providing a robust default predictor under dynamic measurement conditions. These results demonstrate a practical pathway for real time feedstock characterization that can enable feedforward adjustments and more resilient gasifier operation for variable quality waste derived fuels.

Biomass↗
DOE OSTI2020

On the symmetries of cosmological perturbations

The space of inflationary models is vast, containing wide varieties of mechanisms, symmetries, and spectra of particles. Consequently, the space of observational signatures is similarly complex. Hence, it is natural to look for boundaries of the space of models and their signatures. In this paper, we explore the possible symmetries associated with the primordial cosmological perturbations and their correlators in the asymptotic future. Assuming the observed homogeneity, isotropy and (approximate) scale invariance, we prove three main results. First, correlation functions of scalar metric fluctuations are uniquely characterized by soft theorems and are free from ambiguity under field redefinitions. Second, whatever the particle content and interactions, when the standard soft theorems apply, invariance under de Sitter boosts (linearly realized conformal invariance) is only possible if all connected correlators vanish identically, i.e. if the theory is free. Third, conformal invariance is the largest set of linearly realized (bosonic) symmetries of the correlators of any single scalar, irrespectively of any soft theorems or particle content.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Structure of a 28.5 kDa duplex-embedded G-quadruplex system resolved to 7.4 Å resolution with cryo-EM

Genomic regions with high guanine content can fold into non-B form DNA four-stranded structures known as G-quadruplexes (G4s). Extensive in vivo investigations have revealed that promoter G4s are transcriptional regulators. Little structural information exists for these G4s embedded within duplexes, their presumed genomic environment. Here, we report the 7.4 Å resolution structure and dynamics of a 28.5 kDa duplex-G4-duplex (DGD) model system using cryo-EM, molecular dynamics, and small-angle X-ray scattering (SAXS) studies. The DGD cryo-EM refined model features a 53° bend induced by a stacked duplex-G4 interaction at the 5’ G-tetrad interface with a persistently unstacked 3’ duplex. The surrogate complement poly dT loop preferably stacks onto the 3’ G-tetrad interface resulting in occlusion of both 5’ and 3’ tetrad interfaces. Structural analysis shows that the DGD model is quantifiably more druggable than the monomeric G4 structure alone and represents a new structural drug target. Our results illustrate how the integration of cryo-EM, MD, and SAXS can reveal complementary detailed static and dynamic structural information on DNA G4 systems.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Impacts of Experimentally Obtained Harmonic Spectrums of Residential Appliances on Distribution Feeder: Preprint

This paper focuses on the harmonic load flow study for a set of residential loads and the impacts of the harmonic contents on the distribution feeder. Owing to the increased use of the power electronic based appliances and energy efficient home equipment like the lighting loads, the percentage of non-linear loads has increased in the distribution system which can impact the system performance, loss, and stability. Thus a comprehensive knowledge of their power quality and harmonic analysis is essential to improve the load models, voltage stability assessment, determining possible interactions at harmonic frequencies, protection planning, and the effect of the system impedance. For this study, the household appliances include the lighting, power electronics, resistive, and motor loads with a nominal supply voltage of 120 V single-phase or 240 V split-phase at a nominal frequency of 60 Hz. The harmonic spectrum as obtained from the experimental data is used to solve the harmonic load flow for a detailed secondary network including the distribution transformer extracted from a real distribution feeder's model. Additionally, the impact of the voltage harmonic on a three phase test load is presented through experimental results. The harmonic data of the transformer terminal voltage as obtained from the former load flow study is scaled to generate the source voltage for the three phase configuration of the grid simulator to make the test setup very similar to a real scenario.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Reaction kinetics during early hydration of calcined phyllosilicates in clinker-free model systems

Investigations of nearly pure, calcined phyllosilicates (“meta-phyllosilicates”) in clinker-free model systems were performed in presence and absence of sulfate. Calorimetric investigations show a pronounced reaction during the early reaction period only for metakaolin. Quantitative in situ X-ray diffraction reveals calcium silicate hydrate formation in the systems with metakaolin and metaillite, but not in those with metamuscovite. Ettringite crystallizes in all systems containing sulfate, where only the metakaolin system reaches the maximum ettringite content possible. The amount of aluminum ions released from 2:1 meta-phyllosilicates seems to be insufficient to reach the maximum content. Differences in portlandite dissolution and bound water indicate adsorption effects of calcium or calcium – sulfate ion pair complexes on surfaces of the calcined clay particles. Thus, the chemical as well as the physical influence of the meta-phyllosilicates must be considered to predict the reaction kinetics of calcined clays during early hydration.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Editorial for the Collection "Preparatory Work for the American Wake Experiment (AWAKEN)"

The American WAKE experimeNt (AWAKEN) is a large field campaign focused on gathering observations for improved understanding of atmospheric and wind power plant flow physics, one of the outstanding needs for the wind energy community as described in the Science paper by Veers et al.1 "Grand challenges in wind energy." AWAKEN was planned over several years with an international consortium of numerous stakeholders, including national laboratories, academic researchers, wind turbine manufacturers, and wind farm operators. A highlight of the AWAKEN campaign is the extensive use of remote sensing instrumentation to characterize the atmosphere and its interactions with wind power plants, enabled by recent developments in lidar, radar, and thermodynamic profiling technology. Advanced modeling techniques like mesoscale and large-eddy simulations (LES) also played an important role in the preparation of the experiment and the interpretation of the experimental data collected. This special-topic issue for the Journal of Renewable and Sustainable Energy presents a collection of 12 papers that describe the preparatory work and some initial analyses from the AWAKEN campaign. An overview of the contents of the various papers in this special issue is provided in Sec. II.

17 WIND ENERGY↗
DOE OSTI2022

Investigating the architecture and internal structure of the TOI-561 system planets with CHEOPS, HARPS-N, and TESS

ABSTRACT We present a precise characterization of the TOI-561 planetary system obtained by combining previously published data with TESS and CHEOPS photometry, and a new set of 62 HARPS-N radial velocities (RVs). Our joint analysis confirms the presence of four transiting planets, namely TOI-561 b (P = 0.45 d, R = 1.42 R⊕, M = 2.0 M⊕), c (P = 10.78 d, R = 2.91 R⊕, M = 5.4 M⊕), d (P = 25.7 d, R = 2.82 R⊕, M = 13.2 M⊕), and e (P = 77 d, R = 2.55 R⊕, M = 12.6 R⊕). Moreover, we identify an additional, long-period signal (>450 d) in the RVs, which could be due to either an external planetary companion or to stellar magnetic activity. The precise masses and radii obtained for the four planets allowed us to conduct interior structure and atmospheric escape modelling. TOI-561 b is confirmed to be the lowest density (ρb = 3.8 ± 0.5 g cm−3) ultra-short period (USP) planet known to date, and the low metallicity of the host star makes it consistent with the general bulk density-stellar metallicity trend. According to our interior structure modelling, planet b has basically no gas envelope, and it could host a certain amount of water. In contrast, TOI-561 c, d, and e likely retained an H/He envelope, in addition to a possibly large water layer. The inferred planetary compositions suggest different atmospheric evolutionary paths, with planets b and c having experienced significant gas loss, and planets d and e showing an atmospheric content consistent with the original one. The uniqueness of the USP planet, the presence of the long-period planet TOI-561 e, and the complex architecture make this system an appealing target for follow-up studies.

Lacedelli, G. (ORCID:0000000241977374)↗
DOE OSTI2023

Supplement to M&V Guidelines: Measurement and Verification for Performance-Based Contracts Version 4.0

Measurement and verification (M&V) are key to determining and confirming the continued operation of, and savings associated with, performance-based contracts. The Federal Energy Management Program (FEMP) updates these guidelines to reflect the evolution of M&V to incorporate industry best practices and ensure that savings from these performance-based projects are properly planned, communicated, and realized. FEMP released M&V Guidelines: Measurement and Verification for Federal Energy Projects Version 3.0 in 2008. This document was developed with input from industry-government working groups, previous M&V guideline authors, and national laboratory subject matter experts. The document provided the methods and guidelines, with a focus on federal energy savings performance contracts (ESPCs). When FEMP released M&V Guidelines: Measurement and Verification for Performance-Based Contracts Version 4.0 in 2015, FEMP expanded the intended audience to include anyone (energy managers, procurement officers, and contractors) involved in implementing performance-based contracts. The streamlined M&V Guidelines Version 4.0 provided the procedures and guidelines needed to quantify savings resulting from installing energy-efficient equipment, water conservation, improved operation and maintenance (O&M), renewable energy, and cogeneration projects with a performance-based contract; however, it removed some of the associated details on topics such as developing regression models and sampling plans. The details and information provided in M&V Guidelines v. 3.0 are still pertinent to M&V for performance-based contracts. The objective is to keep FEMP M&V version 4.0 condensed, providing the reference document for specifying M&V methods and procedures and a resource for developing project-specific M&V plans; this supplement provides additional details. The content of this supplement has been updated to include pertinent revisions between M&V version 3.0 and M&V version 4.0 by providing details and updating the content to ensure relevancy.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

Quantitative measurements of dislocations in metals for advancing predictive simulations

LLNL applications require scientists to predict how materials evolve under various thermomechanical conditions. While this is achieved through physics-based simulations, uncertainty in the predictions of mechanical properties remains a serious challenge that limits the predictive capabilities of models because we lack methods to compare predictions of atomic-scale defects (dislocations) with experimental measurements. High energy X-ray diffraction (HEXRD) is the most relevant technique that can provide the necessary statistical information on dislocations. However, this technique is not yet quantitative because we lack a precise understanding of the relationship between X-ray diffraction patterns and the underlying material dislocation content and arrangements. To address this need, we used our novel computational X-ray diffraction method to simulate the effect of dislocations on the diffraction patterns. We compared virtual and experimental diffraction patterns. Results allowed us to clearly establish the relationship between X-ray diffraction patterns and the underlying dislocation structures, proving that it is feasible to quantitatively measure dislocation statistics with HEXRD. This project delivered a method that can provide the missing piece to LLNL’s mechanical property simulations in advanced metals by obtaining experimentally long-needed quantitative dislocation data, which could fully enable predictive capabilities.

36 MATERIALS SCIENCE↗
DOE OSTI2024

LINAC Electrical Cabinet - Structural Analysis

Along LINAC s downstream path is a floor containing various cabinets above the LINAC. Of the dozens of cabinets are 4 specific cabinet types: PFN (pulse-forming network) Module, PFN Power Supply, Water Skid, and Marx. Each of these cabinets may contain some of the various contents that include electronics, wiring, circuits, and conduits. In addition, high voltage and low conductivity water (LCW) piping are also present within the cabinets. Occasionally, Lab Technicians perform maintenance and inspections of the cabinets and need to access every part, including the top section that is subject to the weight of the technician standing on top. To ensure the cabinet is structurally safe, a CAD model was developed for each cabinet and a Finite Element Analysis (FEA) was performed on each cabinet to confirm it is safe to stand on.

Blas, Efren↗
DOE OSTI2022

Characterizing soil water content variability across spatial scales from optimized high-resolution distributed temperature sensing technique

Fiber-optic Distributed Temperature Sensing, when combined with the Single-probe Heat-pulse technique can measure soil moisture (θ) across spatial scales. The key limitation of this system is in obtaining the relationship between soil thermal conductivity (λ) and θ for a specific field. Using the Department of Energy Atmospheric Radiation Measurement (ARM) site, this study tested a new methodology to account for the spatial variability in the λ-θ relationship using a Gaussian processes model. The resulting accurate θ measurements (RMSE = 0.03 m 3 m –3 ) were used to characterize the spatial variability of θ across scales and to develop an empirical equation that can correct for the changes in the θ spatial variability observed at different spatial resolutions. In addition, the number of required samples to accurately characterize θ and its variability over scales ranging from 5 m and 350 m were estimated. Finally, these findings provide key information to scale soil moisture from centimeters to hundreds of meters for process understanding.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

The carbon content of Earth and its core

Earth’s core is likely the largest reservoir of carbon (C) in the planet, but its C abundance has been poorly constrained because measurements of carbon’s preference for core versus mantle materials at the pressures and temperatures of core formation are lacking. Using metal–silicate partitioning experiments in a laser-heated diamond anvil cell, we show that carbon becomes significantly less siderophile as pressures and temperatures increase to those expected in a deep magma ocean during formation of Earth’s core. Based on a multistage model of core formation, the core likely contains a maximum of 0.09(4) to 0.20(10) wt% C, making carbon a negligible contributor to the core’s composition and density. However, this accounts for ~80 to 90% of Earth’s overall carbon inventory, which totals 370(150) to 740(370) ppm. The bulk Earth’s carbon/sulfur ratio is best explained by the delivery of most of Earth’s volatiles from carbonaceous chondrite-like precursors.

Geosciences↗
DOE OSTI2020

CALPHAD Uncertainty Quantification and TDBX

CALPHAD uncertainty quantification (UQ) is the foundation of materials design with quantified confidence. We report a framework and software packages to enable CALPHAD UQ assessment and calculation using commercial CALPHAD software (Thermo-Calc). This Bayesian inference framework is coupled with a Markov chain Monte Carlo algorithm to establish uncertainty traces with a given thermodynamic database file (TDB) and corresponding experimental data points. This general framework is demonstrated with the Ni–Cr binary system. The algorithm is firstly validated on synthetic data with known ground truth. Then it is applied to real experimental data to generate posterior traces. We develop a file format named TDBX, which provides a single source of truth by combining the original TDB content and the traces for each assessed Gibbs energy parameter. CALPHAD UQ calculations are performed based on the TDBX file, from which uncertainties for phase boundaries, enthalpy curves, and solidification range are collected as examples of basic design parameters. This TDBX file with corresponding scripts are made open-source. Finally, the combination of CALPHAD UQ assessments and calculations connected by TDBX supports uncertainty-assisted modeling, enabling the integrated application of modern design with uncertainty methodologies to computational materials design.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Meso-scale modelling of compressive fracture in concrete with irregularly shaped aggregates

This paper presents a meso-scale modelling framework to investigate the fracture process in concrete subjected to uniaxial and biaxial compression accounting for its mesostructural characteristics. 3D mesostructure of concrete consisting of coarse aggregates, mortar and interfacial transition zone between them was developed using an in-house code based on the Voronoi tessellation and splining method, which enables to generate the realistic-look aggregates with controllable structural features such as content, location, size and shape. Based on the generated 3D mesostructure, the concrete damage plasticity approach was employed to simulate the compressive fracture behaviour of concrete in terms of crack morphology and stress-strain response against the shape parameters of aggregate. Results indicate that the shape of aggregate has a negligible effect on compressive strength of concrete, which is highly associated with the random location and size distribution of aggregate. The aggregate irregularity has a significant influence on crack initiation and growth of concrete.

36 MATERIALS SCIENCE↗