Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Comparators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Comparing the OpenSolar Remote Shading Analysis Tool to On-Site Shading Measurements

OpenSolar is a free of charge application built for solar installers that creates a fully articulated 3D model of the site and performs remote shading analysis, in order to produce highly accurate designs and interactive, customizable proposals. Under the National Renewable Energy Laboratory (NREL) Commercialization Assistance Program (NCAP), NREL independently verified the accuracy of OpenSolar's remote analysis of solar access percentage values (SAVs) on an annual basis for locations in Los Angeles, CA, and Denver, CO. In aggregate, the results of the analysis show that Open Solar-calculated annual SAV measurements were statistically equivalent within ±2.63 SAVs for Los Angeles locations and ±2.69 SAVs for Denver locations compared to those of on-site measurements made with SunEye devices.

MATHEMATICS AND COMPUTING,SOLAR ENERGY↗

Comparative assessment of neutron flux sensor technologies for advanced reactors

This report documents the comparative assessment of the rhodium-based self-powered neutron detectors (Rh-SPND), micro-pocket fission detectors (MPFD), and dosimetry wires in heated irradiations at the Neutron Radiography reactor facility at Idaho National Laboratory. The sensors performances are evaluated high-temperature environments (upwards of 850°C) during maximum reactor power to simulate use in advanced reactor applications. The performance of the Rh-SPNDs indicates the experiment cartridge heater power supply interferes with the SPND signals. This interference become increasingly significant at temperatures above 500°C with minimal interference observed for temperatures below 500°C. This work also demonstrated the fabrication process for the updated design of the MPFD, but issues related to the seal welds were identified and usable data was limited. Finally, the dosimetry measurements were within the expected range correlated with reactor power; thus, the dosimetry results were used to provide preliminary SPND calibration factors. The results from this experiment serves as a reference for developing and testing of flux sensors that are designed for high-temperature irradiations and advanced reactor deployments. This includes upcoming FY22 irradiations at the Massachusetts Institute of Technology Reactor and the Neutron Radiography (NRAD) reactor utilizing additional fission chambers from Photonis Technologies and fission chambers and SPNDs from The French Alternative Energies and Atomic Energy Commission.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Cross-Kingdom Comparative Genomics of Aromatic Catabolic Pathways in Fungi and Bacteria

The overall goal of this project is to test the hypothesis that white-rot fungi can simultaneously depolymerize lignin extracellularly and catabolize depolymerization products intracellularly as carbon and energy sources. The results from this project will lead to improved understanding of lignin utilization by white-rot fungi, and enable identification of promising fungal strains for lignin catabolism and valorization. As part of this effort, we have conducted a comparative genomic study to investigate a diversity of aromatic catabolic pathways in the fungal and bacterial kingdoms. Furthermore, we have combined genomic and phylogenetic approaches to decipher the evolution of certain aromatic catabolic enzymes and discover new classes of enzymes, which represents a foundation for future biochemical and molecular genetic studies.

aromatic compounds↗

Decarbonization Scenarios in the United States: Comparing Biofuels Growth in Two Models - GCAM and BSM

Scenarios for deep decarbonization rely on biomass for biofuels, biopower, and bioproducts, often including negative emissions via carbon capture and storage or utilization. Despite the prominence of biomass in many deep decarbonization pathways, critical questions remain about biomass allocation, effects of transportation electrification, the pace of growth, and implications for agriculture and land use. We address these questions through a unique comparison of carbon pricing effects on the growth of biomass utilization and its effects on land use in the United States by comparing results from a multisectoral integrated assessment model, the Global Change Analysis Model [GCAM], with results from a biomass-to-biofuels system dynamics model, the Biomass Scenario Model [BSM]. We contribute to model comparison efforts by analyzing the biomass deployment needed for a scenario consistent with a "Middle of the Road" Shared Socioeconomic Pathway [SSP2] and a representative concentration pathway of 2.6 W/m2. The GCAM scenarios solve for global equilibrium conditions that are consistent with this pathway, including demands for biomass across all economic sectors and representing bioenergy with carbon capture and storage as a technology option. The BSM scenarios assess those biomass and biofuel results for the United States and identify challenges associated with that pace and amount of expansion. In the scenario analysis, we harmonize key factors such as carbon price trajectory, domestic ethanol fuel demand, ethanol blending, and arable land availability, and vary them in both models. In GCAM, we vary the carbon price, transportation electrification, ethanol blending constraints, and arable land availability inputs and the value of the carbon in land; in BSM, in addition to directly inputting certain GCAM results, we vary the maximum rate of biorefinery construction, flexibility of feedstock types across conversion processes, and policy incentives such as tax credits and renewable identification number payments. The selected carbon price trajectory results in a rapid increase in biofuel production in the United States, reaching about 9.4 EJ/year in 2060 in the highest scenario analyzed in GCAM. Results differ between the two models in timing and ultimate quantity of biomass and biofuel production. GCAM biofuel quantities generally exceed BSM amounts because CCS is applied to biofuel pathways in GCAM, and because of differences in capacity expansion and related dynamics of land allocation, biomass production, and price dynamics. These dynamics include rapid biorefinery capacity expansion in high demand cases. To satisfy this biomass demand, GCAM rapidly equilibrates land allocation, but the BSM limits the rate at which this re-allocation can occur. A further contrast with the equilibrium approach in GCAM is that the BSM represents a delay between planting and harvesting woody biomass resources. As a result of these model contrasts, feedstock costs in BSM increase more than in GCAM, and the absence of CCS in the BSM also reduces the relative economic attractiveness of biofuels production. The bottlenecks, lags, and price increases also lead to potential for volatility in feedstock price and land allocation to biomass in the BSM. GCAM has more biomass production than BSM in all scenarios, partly because of the broader, economy-wide coverage of GCAM, in contrast to BSM's exclusive focus on biofuels. In both models, trends like those of biofuels production were observed for biomass production: minimal growth without a carbon price and policy incentives, and increases with a carbon price, particularly with carbon capture and storage, because the inputs assume that biopower and biofuels decrease greenhouse gas emissions. In high policy scenarios, biomass demand is high, and the consequent high biomass prices due to the land re-allocation bottleneck in the BSM limit biofuel production even if the biorefinery capacity is expanded. However, because biomass prices do not increase as much in the low policy scenario, growth is slower and the land-reallocation bottleneck no longer dominates, such that the effect of increased capacity can be seen. Across both the models, a change in assumptions from less to more land availability increases biofuel production in both GCAM and BSM, as the upward pressure on feedstock price and volatility are both reduced.

biofuels↗

Ultrasonic Testing (UT) and Computed Tomography (CT) Comparative Scanning of Proposed Additive Manufacturing Reference Standard

This report presents qualitative results of ultrasonic full matrix capture/total focusing method (FMC/TFM) scanning of two series of blocks, additively manufactured by powder bed fusion, containing a variety of internal features and structures that would not be achievable by conventional manufacturing techniques. The purpose of the first series of additively manufactured (AM) blocks was to explore the possibility of building calibration blocks for FMC/TFM ultrasonic testing (UT). It was confirmed that AM is a suitable candidate for generation of unusual and novel reflector forms, such as rotating slots, purposely embedded voids, and tapering holes, and that FMC/TFM was very capable of characterizing them. The intended use of the second series of AM blocks was as UT reference blocks to characterize the AM process quality or the interrogating UT technique. The larger block in this series was scanned from multiple faces, using multiple UT methods (conventional UT and FMC/TFM) and X-ray computed tomography for comparative purposes. The performance of each method was quantified by a metric corresponding to the detection limit of each feature, and the quantitative results are discussed.

36 MATERIALS SCIENCE↗

Comparative Techno-Economic Analysis of Available Feedstocks for High-Temperature Conversion: Whole Tree Thinnings and Mature Pine Residues

The techno-economic and life cycle implications of utilizing low-cost feedstocks in a high temperature conversion process are of great interest. Here, we investigate the conversion cost impacts of two underutilized feedstocks from the commercial pine industry: 13-year-old whole trees, representing trees removed for the purpose of precommercial thinning, and 23-year-old pine residues, representing a waste stream produced from the deconstruction of mature trees for other purposes. Experimental fast pyrolysis (FP) yields for each feedstock were adjusted to a catalytic fast pyrolysis (CFP) basis and used to estimate process economics by employing published correlations based on rigorous techno-economic modeling. These correlations were used in tandem with results from supply and preprocessing analyses to evaluate the field-to-fuel economics of each feedstock. A small difference in minimum fuel selling price (MFSP) was found between the conversion costs for the two feedstocks, with 23-year-old residues demonstrating a net benefit of $0.27 per gasoline gallon equivalent (GGE) compared to the 13- year-old whole tree thinnings, driven primarily by feedstock supply costs. This suggests that both whole tree thinnings and pine residues may be viable feedstock options for CFP conversion. Life cycle inventories (LCIs) were also generated for each case, enabling a field-to-fuel quantification of the cost and carbon cycle associated with each feedstock.

catalytic fast pyrolysis↗

Comparative analysis of cosmological simulations via angular power spectra

Cosmology is the study of the universe's origin, large-scale structure, and dynamics. One such area of study is understanding dark energy and dark matter. Dark matter has not been observed to interact with luminous matter other than through gravitational attractions, forming large scale structures observed throughout the universe. In this area, the primary model is the Lambda Cold Dark Matter (ΛCDM) model. This standard model consists of cosmological dark energy (Λ), cold dark matter (CDM), and normal luminous matter. We use Angular Power Spectra (APS) to compare simulated ΛCDM models with observed large-scale galaxy distributions from the DECam Local Volume Exploration Survey (DELVE). After ensuring that the simulations can produce APS which match observational results, we vary cosmological parameters to constrain the allowed ranges of parameter values that are consistent with the observed data.

Feithen, William↗

Comparing Interaction Graphs on Cascading Outages under Different Loading Conditions

Interaction graphs on cascading outages of power systems provide valuable insights into how cascading outages evolve and propagate, and which components and links are critical to the propagation of cascading outages, enabling further development of mitigation strategies to support decision-making. However, the sensitivity of the interaction graph’s topology to the system’s loading condition has not been studied sufficiently. This paper compared interaction graphs under various loading conditions on the Northeastern Power Coordinating Council 140-bus system, and discovers the strong relationships between the graph topology, the cascade size distribution, and the load condition. Accordingly, three representative interaction graphs are constructed and illustrated.

Guo, Zhenping↗

Performance Assessment of a Dual-purpose HP-TES for a Typical Year Comparing Different Climate Zones

Complete electrification of heating and cooling systems in the United States would overload the existing electrical grid. To this end, recent research efforts have focused on energy storage as one way to reduce ever-increasing peak electricity demands. One such technology is heat pump integrated thermal-energy storage (HP-TES) systems, which can enable load-shifting and reduce demand during peak hours. In this work, a Modelica model of a 4-Ton, dual-mode (heating and cooling) HP-TES system using a room-temperature phase-change material (PCM) integrated through a secondary hydronic loop was developed and simulated for a typical meteorological year in Riverside, CA (ASHRAE Climate Zone 2B), and Chicago, IL (ASHRAE Climate Zone 5A), for a DOE small office prototype building. The COP improvement and demand reduction were analyzed during the time-of-use peak hours along with the required recharge cycle energy demand. A typical summer in Riverside, CA resulted in model-predicted peak COP increases of 50 – 100% compared to the baseline heat pump, especially at higher outdoor temperatures, coupled with maximum peak energy reductions of 22%. During shoulder and winter season simulations, heating energy savings were higher as outdoor temperatures dropped below the PCM phase change temperature. For Chicago, IL, backup heating was necessary to meet the required system capacity for very cold ambient conditions, resulting in winter peak energy savings between 16 – 60% when accounting for backup heating requirements. The recharge energy was found to be mostly below the baseline HP energy during the peak. With improved component selections and controls, the recharge energy may be reduced. The outcomes from the simulations can provide first-order estimates for potential peak energy savings, challenges, and required controls in any location before conducting any field testing.

25 ENERGY STORAGE↗

Crossing The Gap Using Variational Quantum Eigensolver: A Comparative Study

Within the evolving domain of quantum computational chemistry, the Variational Quantum Eigensolver (VQE) has been developed to explore not only the ground state but also the excited states of molecules. In this study, we compare the performance of Variational Quantum Deflation (VQD) and Subspace-Search Variational Quantum Eigensolver (SSVQE) methods in determining the low-lying excited states of $LiH$. Our investigation reveals that while VQD exhibits a slight advantage in accuracy, SSVQE stands out for its efficiency, allowing the determination of all low-lying excited states through a single parameter optimization procedure. We further evaluate the effectiveness of optimizers, including Gradient Descent (GD), Quantum Natural Gradient (QNG), and Adam optimizer, in obtaining $LiH$'s first excited state, with the Adam optimizer demonstrating superior efficiency in requiring the fewest iterations. Moreover, we propose a novel approach combining Folded Spectrum VQE (FS-VQE) with either VQD or SSVQE, enabling the exploration of highly excited states. We test the new approaches for finding all three $H_4$'s excited states. Folded Spectrum SSVQE (FS-SSVQE) can find all three highly excited states near $-1.0$ Ha with only one optimizing procedure, but the procedure converges slowly. In contrast, although Folded spectrum VQD (FS-VQD) gets highly excited states with individual optimizing procedures, the optimizing procedure converges faster.

Chen, I-Chi↗

Comparative Effects of Radiation Sterilization Modality on Medical PVC Tubing

As the production volume of single-use, polymer-based medical devices increases each year, so does the need for throughput capacity to sterilize the devices. Around 80% of radiation-sterilized devices are processed using gamma-ray radiation from industrial cobalt-60 sources. Supply chain, security, and disposal concerns are prompting manufacturers and contract sterilizers to explore alternatives to irradiation using cobalt-60 gamma-rays, such as electron beam (E-beam) and X-ray radiation. Advantages of these ‘machine’ sources over radioisotope-based sources are that they do not decay, a characteristic that requires cobalt-60 to be replaced over time, they can be turned off when not in use, and they do not represent the same level of concern regarding misuse. One of the barriers to direct transition from gamma-ray sterilization to E-beam or X-ray sterilization is concern over the relatively unknown effects of sterilization dose of these alternative modalities on the performance of medical device polymers. Commercially available medical devices sterilized with gamma-ray irradiation exhibit acceptable device function, acceptable mechanical performance, and acceptable discoloration. To be viable, alternate sterilization methods must not only achieve acceptable sterilization, but the process must also result in a product with functional, mechanical, and visual effects acceptable to customers and the regulator. Flexible polyvinyl chloride (PVC) is a plastic material that is commonly found in single-use medical devices and is known for its sensitivity to radiation processing. For instance, transparent PVC is known to yellow upon irradiation. To encouraging sterilization alternatives to cobalt-60 gamma-ray, we directly compared the effects of gamma-ray, E-beam, and X-ray radiation exposure at similar sterilization-relevant doses on key properties of medical grade PVC tubing.

cobalt-60↗

Comparative Analysis of HEATNETS for Geothermal Network Performance: Preprint

Thermal energy networks (TENs), also known as 5th generation district energy systems, or more specifically geothermal networks when exchanging heat with geothermal boreholes, are an important technology for decarbonization. In these networks an ambient loop connects buildings and thermal sources, such as a borehole field, to exchange energy and maintain a desired loop temperature. Water-source heat pumps are used at the buildings to connect to the ambient or thermal loop to meet to the building heating and cooling loads and maintain comfort. A semi-transient, reduced-order technical model and techno-economic model, called HEATNETS, has been developed at NREL that captures the flow of energy around a TEN. In this work, a comparison of the HEATNETS technical model and a well-known coding platform used for modeling geothermal networks, TRNSYS, has been completed for a proposed geothermal network as a verification process. Hourly data provided from the TRNSYS simulation included building loads, pumping power, heat pump power, temperature entering and leaving the borehole field, and mass flow rates. The hourly borehole temperatures were used to create a linear regression model utilized in HEATNETS to estimate the borehole field heat exchange. The building loads and mass flow rates were direct inputs to HEATNETS while the pumping power, heat pump power, borehole temperatures, and coefficients of performance were all simulated and calculated by HEATNETS, allowing for direct comparison of the thermal energy transfer, rather than also comparing control systems responses. HEATNETS considers the full process from design inputs to economic outputs and can provide modeling options for high-level initial system design and operational optimization. This study shows that HEATNETS, while not intended to replace other modeling tools, can be a unique modeling tool for the performance of a full geothermal network system.

15 GEOTHERMAL ENERGY↗

Comparing CRT and Pandora Tagged Tracks in ICARUS

The ICARUS Liquid Argon Time Projection Chamber (LArTPC) is used to investigate short-baseline neutrino oscillations and the possible existence of sterile neutrinos. To aid in identifying and rejecting cosmic ray backgrounds, the system is outfitted with external Cosmic Ray Taggers (CRTs). The CRT is able to measure more tracks and at a wider range of angles, useful in further detailing future calibrations. This project compared the most probable values (MPVs) of charge deposition between CRT tagged and TPC tagged tracks. The Y-Z maps of charge scale for both datasets show a strong correlation, not just in their overall structure, but also in how they reflect known detector effects. Both reconstruction paths showed similar structures in their charge distribution, such as less effective wire section or mechanical support, confirming that CRT-tagged tracks, despite being external, respond to the same calibration landscape as Pandora tracks, validating previous Pandora reconstructions and values. Overall, the analysis supports the idea that the CRT tags are a useful addition to ICARUS calibration efforts. Their broad angular range and independence from Pandora reconstruction make them a helpful secondary tool and a potential asset in extending calibration across the detector volume.

Thayer, Abbie [Fermilab; Colorado State U.]↗

Comparing Control Performance Between Simulation and Experiment using the Microreactor Automated Control System Testbed

In the advanced reactor domain, a flexible and scalable software/hardware infrastructure is crucial for integrating and validating various control technologies. This study used the Microreactor Automated Control System (MACS) hardware platform as a testbed. MACS was originally designed to mirror Idaho National Laboratory (INL)'s Microreactor Applications Research Validation and Evaluation (MARVEL), a 85-kW thermal fission microreactor. It features control drums for simulated reactivity control; lights that function as a surrogate reactor core, with the brightness being proportional to the reactor power; and light sensors that emulate neutron detectors. To transform MACS into a physical twin of MARVEL for evaluating control methods, the Control and Optimization Modular Modeling Application for Nuclear Deployment (COMMAND) software was employed. This software integrated the hardware with two models of the MARVEL core, based on Reactor Excursion and Leak Analysis Program (RELAP5-3D) and Monte Carlo N-Particle (MCNP) models. The study aimed to demonstrate the gap between control theory and actual practice—a gap that often necessitates empirical adjustments such as control gain retuning, filters, time discretization, and integrator anti-windup measures. Controllers were developed based on increasingly complex simulations without hardware, starting from the base MARVEL model and then introducing actuator saturation constraints and sensor noise. The final control strategy was then tested using MACS, and a comparative performance analysis was conducted.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗

Comparative investigation of iterative solutions of the all-frequency stable formulation and its vector-potential-only variation

An all-frequency stable formulation has been proposed and applied to solve low-frequency and multiscale electromagnetic problems to avoid the low-frequency breakdown catastrophe of the traditional vector wave equation. Based on the potential representation of the fields, this formulation involves vector and scalar potentials, as well as an auxiliary potential to enforce the gauge condition. In this paper, such a formulation is first simplified to involve vector potential only. Their iterative solutions are then sought by using an incomplete LU preconditioner and an iterative solver. The iterative performance of both formulations are investigated in a comparative study.

Mekonnen, Minyechil↗

Design of a Cryogenic Assembly for Comparing Qubit Infrared Packaging Inefficiencies

It is well known that everything emits infrared (IR) light in the form of thermal radiation. IR radiation on superconducting qubits carries enough energy to cause decoherence and so-called “quasiparticle poisoning.” Therefore, proper IR shielding is needed to keep the qubit in a high-coherence state. However, trying to extract IR-specific information from a qubit is difficult, so a microwave kinetic inductance detector (MKID) can be used instead. We show that the IR shielding inefficiencies of MKID packages can only be compared with other packaging inefficiencies. We create a cryogenic assembly CAD design, consisting of magnetic shield cans, a copper mounting plate and mounts, and an MKID enclosure, which thermalizes the assembly to dilution refrigerator temperatures. Phase 1 of this design involves using a narrowband IR laser source to test the IR shielding of packaging at the laser’s wavelength. When the best IR shielding packaging is determined, the superconducting qubit can replace the MKID, allowing the qubit to avoid decoherence due to IR radiation and boost its performance and coherence lifetime.

Mailliard, Robert J. [Fermilab] (ORCID:00090000277↗

Comparative Analysis of Natural Gas Cogeneration Incentives on Electricity Production in Latin America

An analysis to assess the influence of country-dependent variables and incentives on the feasibility of natural gas cogeneration projects in Latin America is presented in this work. The analysis is performed using a hypothetical industrial plant, where the cogeneration solution consists in the recovery of waste heat from the power generation for steam production. The feasibility is evaluated by calculating the Return of Investment (ROI) and the Internal Rate of Return (IRR) of the project. Eight Latin American countries are studied considering their specific natural gas markets, regulation, and macroeconomic variables. Two scenarios, electricity production for self-consumption and electricity production with power surplus sale, are independently analyzed considering the effects of available incentives. In the countries where the project is feasible, the application of incentives leads to a significant reduction in the ROI and, consequently, to an increment in the IRR. The effect of the interest rate and environmental impact were also analyzed. In general terms, along the region, the regulation for cogeneration is incipient while incentives are very standard and similar respect to lowering of import, Value-Added Tax (VAT), and income taxes, which seems to be designed purely to promote capital investment. Following the results from this study, it is of paramount importance to create new policy instruments in the future to advance the regulatory framework for cogeneration in Latin America.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗