Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONCRETES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Static tests of excess ground attenuation at Wallops Flight Center

An extensive experimental measurement program which evaluated the attenuation of sound for close to horizontal propagation over the ground was designed to replicate, under static conditions, results of the flight measurements carried out earlier by NASA at the same site (Wallops Flight Center). The program consisted of a total of 41 measurement runs of attenuation, in excess of spreading and air absorption losses, for one third octave bands over a frequency range of 50 to 4000 Hz. Each run consisted of measurements at 10 locations up to 675 m, from a source located at nominal elevations of 2.5, or 10 m over either a grassy surface or an adjacent asphalt concrete runway surface. The tests provided a total of over 8100 measurements of attenuation under conditions of low wind speed averaging about 1 m/s and, for most of the tests, a slightly positive temperature gradient, averaging about 0.3 C/m from 1.2 to 7 m. The results of the measurements are expected to provide useful experimental background for the further development of prediction models of near grazing incidence sound propagation losses.

Sutherland, L. C.↗
NASA NTRS1981

Process development for automated solar cell and module production. Task 4: Automated array assembly

Progress in the development of automated solar cell and module production is reported. The unimate robot is programmed for the final 35 cell pattern to be used in the fabrication of the deliverable modules. The mechanical construction of the automated lamination station and final assembly station phases are completed and the first operational testing is underway. The final controlling program is written and optimized. The glass reinforced concrete (GRC) panels to be used for testing and deliverables are in production. Test routines are grouped together and defined to produce the final control program.

Hagerty, J. J.↗
NASA NTRS1981

Low-cost solar array structure development

Early studies of flat-plate arrays have projected costs on the order of $50/square meter for installed array support structures. This report describes an optimized low-cost frame-truss structure that is estimated to cost below $25/square meter, including all markups, shipping an installation. The structure utilizes a planar frame made of members formed from light-gauge galvanized steel sheet and is supposed in the field by treated-wood trusses that are partially buried in trenches. The buried trusses use the overburden soil to carry uplift wind loads and thus to obviate reinforced-concrete foundations. Details of the concept, including design rationale, fabrication and assembly experience, structural testing and fabrication drawings are included.

Wilson, A. H.↗
NASA NTRS1981

Computational methods in nonlinear structural and solid mechanics; Proceedings of the Symposium, Washington, D.C., October 6-8, 1980. Symposium sponsored by the George Washington University and NASA

Topics discussed include computational strategies for nonlinear problems in structural mechanics, time integration techniques and the numerical solution of nonlinear algebraic equations, material characterization and nonlinear fracture mechanics, nonlinear interaction problems, and seismic response and the nonlinear analysis of concrete structures. Also considered are nonlinear problems for nuclear reactors, crash dynamics and impact problems, nonlinear problems of fibrous composites and advanced nonlinear applications, and computerized symbolic manipulation and nonlinear analysis software systems.

Noor, A. K.↗
NASA NTRS1981

Cornering characteristics of the nose-gear tire of the space shuttle orbiter

An experimental investigation was conducted to evaluate cornering characteristics of the 32 x 8.8 nose gear tire of the space shuttle orbiter. Data were obtained on a dry concrete runway at nominal ground speeds ranging from 50 to 100 knots and over a range of tire vertical loads and yaw angles which span the expected envelope of loads and yaw angles to be encountered during space shuttle landing operations. The cornering characteristics investigated included side and drag forces and friction coefficients, aligning and overturning torques, friction force moment arm, and the lateral center of pressure shift. Results of this investigation indicate that the cornering characteristics of the space shuttle nose gear tire are insensitive to variations in ground speed over the range tested. The effects on cornering characteristics of variations in the tire vertical load and yaw angle are as expected. Trends observed are consistent with trends observed during previous cornering tests involving other tire sizes.

Vogler, W. A.↗
NASA NTRS1981

Design of an energy conservation building

The concepts in designing and predicting energy consumption in a low energy use building are summarized. The building will use less than 30,000 Btu/sq.ft./yr. of boarder energy. The building's primary energy conservation features include heavy concrete walls with external insulation, a highly insulated ceiling, and large amounts of glass for natural lighting. A solar collector air system is integrated into the south wall. Calculations for energy conservation features were performed using NASA's NECAP Energy Program.

Jensen, R. N.↗
NASA NTRS1980

The design of low cost structures for extensive ground arrays

The development of conceptual designs of solar array support structures and their foundations including considerations of the use of concrete, steel, aluminum, or timber are reported. Some cost trends were examined by varying selected parameters to determine optimum configurations. Detailed civil/structural design criteria were developed. Using these criteria, eight detailed designs for support structures and foundations were developed and cost estimates were made. As a result of the study wind was identified as the major loading experienced by these low height structures, whose arrays are likely to extend over large tracts of land. Proper wind load estimating is considered essential to developing realistic structural designs and achieving minimum cost support structures. Wind tunnel testing of a conceptual array field was undertaken and some of the resulting wind design criteria are presented. The SPS rectenna system designs may be less sensitive to wind load estimates, but consistent design criteria remain important.

Franklin, H. A.↗
NASA NTRS1981

Process development for automated solar cell and module production. Task 4: Automated array assembly

The Unimate robot was programmed for the final 35 cell pattern to be used in the fabrication of the deliverable modules. Mechanical construction of the Automated Lamination Station and Final Assembly Station were completed on schedule. All final wiring and interconnect cables were also completed and the first operational testing began. The final controlling program was written. A local fabricator was contracted to produce the glass reinforced concrete panels to be used for testing and deliverables. A video tape showing all three stations in operation was produced.

Hagerty, J. J.↗
NASA NTRS1981

Formal semantic specifications as implementation blueprints for real-time programming languages

Formal definitions of language and system semantics provide highly desirable checks on the correctness of implementations of programming languages and their runtime support systems. If these definitions can give concrete guidance to the implementor, major increases in implementation accuracy and decreases in implementation effort can be achieved. It is shown that of the wide variety of available methods the Hgraph (hypergraph) definitional technique (Pratt, 1975), is best suited to serve as such an implementation blueprint. A discussion and example of the Hgraph technique is presented, as well as an overview of the growing body of implementation experience of real-time languages based on Hgraph semantic definitions.

Feyock, S.↗
NASA NTRS1983

Rewaterproofing Silica Tiles

Waterproofing agent, vaporized in bubbler transported by gas flowing in system and deposits in pores of tiles. Vapor carried through hole of approximately 1/16 inch (1.6.mm) diameter made in tile coating. Technique used to waterproof buildups (concrete and brick) and possibly fabrics.

Lleger, L. J.↗
NASA NTRS1982

Crash tests of four low-wing twin-engine airplanes with truss-reinforced fuselage structure

Four six-place, low-wing, twin-engine, general aviation airplane test specimens were crash tested under controlled free flight conditions. All airplanes were impacted on a concrete test surface at a nomial flight path velocity of 27 m/sec. Two tests were conducted at a -15 deg flight path angle (0 deg pitch angle and 15 deg pitch angle), and two were conducted at a -30 deg flight path angle (-30 deg pitch angle). The average acceleration time histories (crash pulses) in the cabin area for each principal direction were calculated for each crash test. In addition, the peak floor accelerations were calculated for each test as a function of aircraft fuselage longitudinal station number. Anthropomorphic dummy accelerations were analyzed using the dynamic response index and severity index (SI) models. Parameters affecting the dummy restraint system were studied; these parameters included the effect of no upper torso restraint, measurement of the amount of inertia-reel strap pullout before locking, measurement of dummy chest forward motion, and loads in the restraints. With the SI model, the dummies with no shoulder harness received head impacts above the concussive threshold.

Williams, M. S.↗
NASA NTRS1982

The PKI collector

The design and manufacturing of a solar thermal collector is discussed. The collector has three primary subsystems: concentrator, receiver/fluid loop, and controls. Identical curved reflective columns are utilized in a faceted Fresnel design to support 864 one foot square flat inexpensive second-surface, silvered glass mirrors. The columns are ganged together and rotated through their centers of gravity to provide elevation tracking. The concentrator is supported by a lightweight spaceframe structure which distributes all wind and gravity loads to the base supports. The base of the structure is a track which rotates on wheels mounted on concrete piers. A parallel tube steel heat exchanger is mounted at the concentrator focal area in a well insulated, galvanized steel housing. Two rows of vertical close-packed, staggered tubes connect a mud header and a steam header. Automatic two axis tracking and operational control is provided with a microprocessor based package. Concentrator-mounted shadowbands are the basis for active tracking. A software program provides azimuthal tracking during cloudy periods.

Rice, M. P.↗
NASA NTRS1982

Verification testing of the PKI collector at Sandia National Laboratories, Albuquerque, New Mexico

Verification testing of a solar collector was undertaken prior to its operation as part of an industrial process heat plant at Capitol Concrete Products in Topeka, Kansas. Testing was performed at a control plant installed at Sandia National Laboratory, Albuquerque, New Mexico (SNLA). Early results show that plant performance is even better than anticipated and far in excess of test criteria. Overall plant efficiencies of 65 to 80 percent were typical during hours of good insolation. A number of flaws and imperfections were detected during operability testing, the most important being a problem in elevation drive alignment due to a manufacturing error. All problems were corrected as they occurred and the plant, with over 40 hours of operation, is currently continuing operability testing in a wholly-automatic mode.

Hauger, J. S.↗
NASA NTRS1983

Evaluation of Antenna Foundation Elastic Modulus

An experiment to measure the elastic deflection of the DSS 14 concrete pedestal under the weight of the antenna was conducted in February 1983 and is compared to a similiar experiment made in 1968. Comparison of the results confirms the decrease in elastic modulus measured on core samples recently taken from the pedestal.

Mcginness, H.↗
NASA NTRS1983

Coherent scattering of a spherical wave from an irregular surface

The scattering of a spherical wave from a rough surface using the Kirchhoff approximation is considered. An expression representing the measured coherent scattering coefficient is derived. It is shown that the sphericity of the wavefront and the antenna pattern can become an important factor in the interpretation of ground-based measurements. The condition under which the coherent scattering-coefficient expression reduces to that corresponding to a plane wave incidence is given. The condition under which the result reduces to the standard image solution is also derived. In general, the consideration of antenna pattern and sphericity is unimportant unless the surface-height standard deviation is small, i.e., unless the coherent scattering component is significant. An application of the derived coherent backscattering coefficient together with the existing incoherent scattering coefficient to interpret measurements from concrete and asphalt surfaces is shown.

Fung, A. K.↗
NASA NTRS1983

Design procedures for compressor blades

The conventional methods for the design of the blades in the case of axial turbomachines are considered, taking into account difficulties concerning the determination of optimal blade profiles. These difficulties have been partly overcome as a consequence of the introduction of new numerical methods during the last few years. It is pointed out that, in the case of the subsonic range, a new procedure is now available for the determination of the form of blade profile on the basis of a given velocity distribution on the profile surface. The search for a profile form with favorable characteristics is consequently transformed into a search for a favorable velocity or pressure distribution on the blade. The distribution of velocities depends to a large degree on the characteristics of the profile boundary layers. The considered concept is not new. However, its practical implementation has only recently become possible. The employment of the new design procedure is illustrated with the aid of an example involving a concrete design problem.

Starken, H.↗
NASA NTRS1984

Feedback laws for fuel minimization for transport aircraft

The Theoretical Mechanics Branch has as one of its long-range goals to work toward solving real-time trajectory optimization problems on board an aircraft. This is a generic problem that has application to all aspects of aviation from general aviation through commercial to military. Overall interest is in the generic problem, but specific problems to achieve concrete results are examined. The problem is to develop control laws that generate approximately optimal trajectories with respect to some criteria such as minimum time, minimum fuel, or some combination of the two. These laws must be simple enough to be implemented on a computer that is flown on board an aircraft, which implies a major simplification from the two point boundary value problem generated by a standard trajectory optimization problem. In addition, the control laws allow for changes in end conditions during the flight, and changes in weather along a planned flight path. Therefore, a feedback control law that generates commands based on the current state rather than a precomputed open-loop control law is desired. This requirement, along with the need for order reduction, argues for the application of singular perturbation techniques.

Price, D. B.↗
NASA NTRS1984

Determination of the Sources of Radar Scattering

Fine-resolution radar backscattering measurements were proposed to determine the backscattering sources in various vegetation canopies and surface targets. The results were then used to improve the existing theoretical models of terrain scattering, and also to enhance understanding of the radar signal observed by an imaging radar over a vegetated area. Various experiments were performed on targets such as corn, milo, soybeans, grass, asphalt pavements, soil and concrete walkways. Due to the lack of available references on measurements of this type, the obtained results will be used primarily as a foundation or future experiments. The constituent backscattering characteristics of the vegetation canopies was also examined.

Moore, R. K.↗