Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BRITTLENESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

MESOSCALE SIMULATIONS OF POWDER COMPACTION

Mesoscale 3D simulations of shock compaction of metal and ceramic powders have been performed with an Eulerian hydrocode GEODYN. The approach was validated by simulating a well-characterized shock compaction experiment of a porous ductile metal. Simulation results using the Steinberg material model and handbook values for solid 2024 aluminum showed good agreement with experimental compaction curves and wave profiles. Brittle ceramic materials are not as well studied as metals, so a simple material model for solid ceramic (tungsten carbide) has been calibrated to match experimental compaction curves. Direct simulations of gas gun experiments with ceramic powders have been performed and showed good agreement with experimental data. The numerical shock wave profile has same character and thickness as that measured experimentally using VISAR. The numerical results show reshock states above the single-shock Hugoniot line as observed in experiments. We found that for good quantitative agreement with experiments 3D simulations are essential.

36 MATERIALS SCIENCE↗

Spall and damage behavior of S200F beryllium

We have performed a series of plate impact experiments to study the strength and spall damage behavior of S200F Be. Peak stresses achieved were in the range from 5.6-19.2 GPa. VISAR data show long rise times in the approach to the shocked state believed to be the result of twinning occurring alongside, or in defference to slip, in this hcp material, with its free surface never achieving a steady velocity. This data indicate brittle spall behavior with spall strengths in the range of 0.8-0.9 GPa. In experiments where target thickness is varied, we see evidence of precursor decay and present calculations of the Hugoniot Elastic Limit (HEL). Beryllium is a strategically important material to the aerospace and defense industries worldwide. In spite of this, there is surprisingly little recent literature on the dynamic behavior of this material, particularly the S200F grade. Much of the earlier work was performed on either S200D or S200E grades of Be [1,2] from Brush Wellman, Inc., or on material of unstated pedigree [3]. A discussion of the evolution in material processing, resulting chemical composition, grain size, and crystallographic texture in these as-processed grades of Be can be found in [4]. In general, progressing from S200D, to E, to F entails reduced BeO and other impurity contents, reduced grain size, and a reduction in crystallographic texture of the starting material [4]. The primary goal of this investigation was to study the strength and damage behavior of S200F under dynamic loading conditions. A secondary goal was to obtain equation-of-state (EOS) data to supplement and compare with those already reported in the literature.

36 MATERIALS SCIENCE↗

IDENTIFYING FRACTURE ORIGIN IN CERAMICS BY COMBINATION OF NONDESTRUCTIVE TESTING AND DISCRETE ELEMENT ANALYSIS

Advanced ceramic materials have been extensively applied in aerospace, automobile and other industries. However, the reliability of the advanced ceramics is a major concern because of the brittle nature of the materials. In this paper, combination of nondestructive testing and numerical modeling Discrete Element Method is proposed to identify the fracture origin in ceramics. The nondestructive testing--laser scattering technology is first performed on the ceramic components to reveal the machining-induced damage such as cracks and the material-inherent flaws such as voids, then followed by the four point bending test. Discrete Element software package PFC{sup 2D} is used to simulate the four point bending test and try to identify where the fractures start. The numerical representation of the ceramic materials is done by generating a densely packed particle system using the specimen genesis procedure and then applying the suitable microparameters to the particle system. Simulation of four point bending test is performed on materials having no defects, materials having manufacturing-induced defects like cracks, and materials having material-inherent flaws like voids. The initiation and propagation of defects is modeled and the mean contact force on the loading ball is also plotted. The simulation prediction results are well in accordance with the nondestructive testing results.

36 MATERIALS SCIENCE↗

Liquid Metal Walls, Lithium, And Low Recycling Boundary Conditions In Tokamaks

At present, the only solid material believed to be a viable option for plasma-facing components (PFCs) in a fusion reactor is tungsten. Operated at the lower temperatures typical of present-day fusion experiments, tungsten is known to suffer from surface degradation during long-term exposure to helium-containing plasmas, leading to reduced thermal conduction to the bulk, and enhanced erosion. Existing alloys are also quite brittle at temperatures under 700 deg. C. However, at a sufficiently high operating temperature (700 - 1000 deg. C), tungsten is self-annealing and it is expected that surface damage will be reduced to the point where tungsten PFCs will have an acceptable lifetime in a reactor environment.The existence of only one potentially viable option for solid PFCs, though, constitutes one of the most significant restrictions on design space for DEMO and follow-on fusion reactors. In contrast, there are several candidates for liquid metal-based PFCs, including gallium, tin, lithium, and tin-lithium eutectics. We will discuss options for liquid metal walls in tokamaks, looking at both high and low recycling materials. We will then focus in particular on one of the candidate liquids, lithium.Lithium is known to have a high chemical affinity for hydrogen, and has been shown in test stands and fusion experiments to produce a low recycling surface, especially when liquid. Because it is also low-Z and is usable in a tokamak over a reasonable temperature range (200 - 400 deg. C), it has been now been used as a PFC in several confinement experiments (TFTR, T11-M, CDX-U, NSTX, FTU, and TJ-II), with favorable results. The consequences of substituting low recycling walls for the traditional high recycling variety on tokamak equilibria are very extensive. We will discuss some of the expected modifications, briefly reviewing experimental results, and comparing the results to expectations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermal Aspects of Ductile Mode Micro Laser Assisted Machining

This paper presents the simulation work performed to study an innovative process called micro-Laser Assisted Machining ({mu}-LAM). {mu}-LAM is being used for machining hard and brittle semiconductor and ceramic materials such as Silicon Carbide. Numerical simulations were carried out using the commercial software AdvantEdge Version 5.4. The cutting tool is modeled as a single point diamond tip. The workpiece material (4H-SiC) is heated locally during the actual machining process by a laser beam, which passes through the diamond tool tip. The workpiece is heated beyond the thermal softening point in order to study the effect of increased temperature on the machining process. The initial work started with an approximate thermal softening curve to ensure that thermal effects can be incorporated in the simulation model. A new thermal softening curve was developed based upon experimental data and implemented in the material model. A thermal boundary was provided on the workpiece top surface to simulate the effect of laser heating. In all three cases the chip formation was observed and the changes in cutting and thrust forces were evaluated. The simulation results indicate a significant decrease in machining forces if Silicon Carbide is heated and thermally softened thus demonstrating the benefits of the {mu}-LAM process.

36 MATERIALS SCIENCE↗

Experimental Analysis of Work-piece's Diametrical Error in Ultrasonic-Vibration-Assisted Turning

Vibration at an ultrasonic frequency is superimposed on the ordinary cutting motion in ultrasonic-vibration-assisted turning (UAT). This combinatory cutting motion results in reduction of the cutting force and surface roughness, and improvement of the dimensional tolerances compared with conventional turning (CT). The advantages obtainable from UAT has made this process suitable for machining hard-to-cut and brittle materials such as super-alloys and ceramics, as well as ordinary materials. The elastic deflection of work-pieces is primarily responsible for the diametrical errors of the machined parts. This is of course more obvious for slender work-pieces. The influence of UAT process on the diametrical error has not yet been investigated. This has been partly undertaken by the authors of the present paper. It has been experimentally illustrated in this paper that ultrasonic vibration superimposed on the tool tip can result in reduction of the diametrical error and thus reduced scrap rate is ensued.

36 MATERIALS SCIENCE↗

Oxynitrided Surface Layer Produced On Ti6Al4V Titanium Alloy Under Low Temperature Glow Discharge Conditions For Medical Applications

In spite that titanium oxides increase biocompatibility of titanium implants but their functional life is limited due to the problems arising from brittles and metalosis. Therefore technology, that allow to produce composite surface layer with controlled microstructure, chemical and phase composition and surface morphology on titanium alloy and eliminates the oxides disadvantages has been existing till now is searched. The requirements of titanium and its alloys implants can be fulfill by the low-temperature glow discharge assisted oxynitriding.The paper describes the surface layer of TiO{sub 2}+TiN+Ti{sub 2}N+{alpha}Ti(N) type produced at temperature 680 deg. C that preserves mechanical properties of titanium alloy Ti6Al4V. Characteristics of produced diffusion multi-phase surface layers in range of phase composition, microstructure (SEM, TEM, XRD) and its properties, such as frictional wear resistance are presented. The biological properties in dependency to the applied sterilization method are also analyzed.Properties of produced surface layers are discussed with reference to titanium alloy. The obtained data show that produced surface layers improves titanium alloy properties both frictional wear and biological. Preliminary in vitro examinations show good biocompatibility and antithrombogenic properties.

36 MATERIALS SCIENCE↗

Experimental Investigations on Pulsed Nd:YAG Laser Welding of C17300 Copper-Beryllium and 49Ni-Fe Soft Magnetic Alloys

Copper-beryllium and soft magnetic alloys must be joined in electrical and electro-mechanical applications. There is a high difference in melting temperatures of these alloys which cause to make the joining process very difficult. In addition, copper-beryllium alloys are of age hardenable alloys and precipitations can brittle the weld. 49Ni-Fe alloy is very hot crack sensitive. Moreover, these alloys have different heat transfer coefficients and reflection of laser beam in laser welding process. Therefore, the control of welding parameters on the formation of adequate weld puddle composition is very difficult. Laser welding is an advanced technique for joining of dissimilar materials since it can precisely control and adjust the welding parameters. In this study, a 100W Nd:YAG pulsed laser machine was used for joining 49Ni-Fe soft magnetic to C17300 copper-beryllium alloys. Welding of samples was carried out autogenously by changing the pulse duration, diameter of beam, welding speed, voltage and frequency. The spacing between samples was set to almost zero. The ample were butt welded. It was required to apply high voltage in this study due to high reflection coefficient of copper alloys. Metallography, SEM analysis, XRD and microhardness measurement was used for survey of results. The results show that the weld strength depends upon the chemical composition of the joints. To change the wells composition and heat input of the welds, it was attempted to deviate the laser focus away from the weld centerline. The best strength was achieved by deviation of the laser beam away about 0.1mm from the weld centerline. The result shows no intermetallic compounds if the laser beam is deviated away from the joint.

36 MATERIALS SCIENCE↗

The Effect of Cutting Speed in Metallic Glass Grinding

In this paper, the effects of the cutting speed in metallic glass grinding were investigated in dry conditions. The results showed that grinding forces decrease as grinding energy increase with the increasing cutting speeds. The present investigations on ground surface and grinding chips morphologies -shows that material removal and surface formation of the BMG are mainly due to the ductile chip deformation and ploughing as well as brittle fracture of some particles from the edges of the tracks. The roughness values obtained with the Cubic Boron Nitride wheels are acceptable for the grinding operation.

36 MATERIALS SCIENCE↗

Multiscale Modeling of the Orthotropic Behaviour of PA6-6 overmoulded Composites using MMI Approach

In this study the MMI ConfidentDesign multiscale approach (consisting in a non-linear multiscale simulation based on DIGIMAT registered including the injection modeling of the filled polymer and a multiscale mechanical model using the fiber orientation tensor resulting from the injection) has been combined with an orthotropic damageable elastic simulation. The anisotropic properties (including rupture criterion) are estimated and a multiscale simulation including the heterogeneous material properties issued from injection process is done. The impact of fiber ratios is then investigated. The structural simulation predicts stresses localized close to the punch, as well in injected PA66 than in composite part. Greater the fiber volume ratio, greater the modulus and more brittle the composite.

36 MATERIALS SCIENCE↗

Diode laser welding of aluminum to steel

Laser welding of dissimilar materials was carried out by using a high power diode laser to join aluminum to steel in a butt-joint configuration. During testing, the laser scan rate was changed as well as the laser power: at low values of fluence (i.e. the ratio between laser power and scan rate), poor joining was observed; instead at high values of fluence, an excess in the material melting affected the joint integrity. Between these limiting values, a good aesthetics was obtained; further investigations were carried out by means of tensile tests and SEM analyses. Unfortunately, a brittle behavior was observed for all the joints and a maximum rupture stress about 40 MPa was measured. Apart from the formation of intermeltallic phases, poor mechanical performances also depended on the chosen joining configuration, particularly because of the thickness reduction of the seam in comparison with the base material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of Process Parameters on Ultrasonic Micro-Hole Drilling in Glass and Ruby

Brittle materials such as ceramics, glasses and oxide single crystals find increasing applications in advanced micro-engineering products. Machining small features in such materials represents a manufacturing challenge. Ultrasonic drilling constitutes a promising technique for realizing simple micro-holes of high diameter-to-depth ratio. The process involves impacting abrasive particles in suspension in a liquid slurry between tool and work piece. Among the process performance criteria, the drilling time (productivity) is one of the most important quantities to evaluate the suitability of the process for industrial applications.This paper summarizes recent results pertaining to the ultrasonic micro-drilling process obtained with a semi-industrial 3-axis machine. The workpiece is vibrated at 40 kHz frequency with an amplitude of several micrometers. A voice-coil actuator and a control loop based on the drilling force impose the tool feed. In addition, the tool is rotated at a prescribed speed to improve the drilling speed as well as the hole geometry. Typically, a WC wire serves as tool to bore 200 {mu}m diameter micro-holes of 300 to 1,000 {mu}m depth in glass and ruby. The abrasive slurry contains B4C particles of 1 {mu}m to 5 {mu}m diameter in various concentrations.This paper discusses, on the basis of the experimental results, the influence of several parameters on the drilling time. First, the results show that the control strategy based on the drilling force allows to reach higher feed rates (avoiding tool breakage). Typically, a 8 um/s feed rate is achieved with glass and 0.9 {mu}m/s with ruby. Tool rotation, even for values as low as 50 rpm, increases productivity and improves holes geometry. Drilling with 1 {mu}m and 5 {mu}m B4C particles yields similar productivity results. Our future research will focus on using the presented results to develop a model that can serve to optimize the process for different applications.

36 MATERIALS SCIENCE↗

Improvement in hardness of soda-lime-silica glass

Hardness is a key design parameter for structural application of brittle solids like glass. Here we report for the first time the significant improvement of about 10% in Vicker's hardness of a soda-lime-silica glass with loading rate in the range of 0.1-10 N.s{sup -1}. Corroborative dark field optical and scanning electron microscopy provided clue to this improvement through evidence of variations in spatial density of shear deformation band formation as a function of loading rate.

36 MATERIALS SCIENCE↗

On the characteristic length scales associated with plastic deformation in metallic glasses

Atomistic simulations revealed that the spatial correlations of plastic displacements in three metallic glasses, FeP, MgAl, and CuZr, follow an exponential law with a characteristic length scale l{sub c} that governs Poisson's ratio {nu}, shear band thickness t{sub SB}, and fracture mode in these materials. Among the three glasses, FeP exhibits smallest l{sub c}, thinnest t{sub SB}, lowest {nu}, and brittle fracture; CuZr exhibits largest l{sub c}, thickest t{sub SB}, highest {nu}, and ductile fracture, while properties of MgAl lie in between those of FeP and CuZr. These findings corroborate well with existing experimental observations and suggest l{sub c} as a fundamental measure of the shear transformation zone size in metallic glasses.

36 MATERIALS SCIENCE↗

The bonding, charge distribution, spin ordering, optical, and elastic properties of four MAX phases Cr{sub 2}AX (A = Al or Ge, X = C or N): From density functional theory study

In this work, we assess a full spectrum of properties (chemical bonding, charge distribution, spin ordering, optical, and elastic properties) of Cr{sub 2}AC (A = Al, Ge) and their hypothetical nitride counterparts Cr{sub 2}AN (A = Al, Ge) based on density functional theory calculations. The calculated total energy values indicate that a variety of spin ordering of these four compounds depending on interlayer-interactions between M-A and M-X within the sublattice, which is supported by bonding analysis. MAX phase materials are discovered to possess exotic magnetic properties which indicates that these materials could serve as promising candidates for novel layered magnetic materials for various electronic and spintronic applications. Further analysis of optical properties for two polarization vectors of Cr{sub 2}AX shows that the reflectivity is high in the visible-ultraviolet region up to ∼15 eV suggesting Cr{sub 2}AX as a promising candidate for use as a coating material. The elastic coefficients (C{sub ij}) and bulk mechanical properties [bulk modulus (K), shear modulus (G), Young's modulus (E), Poisson's ratio (η), and Pugh ratio (G/K)] of these four Cr{sub 2}AX compounds are also calculated and analyzed, which pave the way to predict or design new MAX phases that are less brittle or tougher by having a lower G/K value or higher η.

36 MATERIALS SCIENCE↗

First principle study of elastic and thermodynamic properties of FeB{sub 4} under high pressure

The elastic properties, elastic anisotropy, and thermodynamic properties of the lately synthesized orthorhombic FeB{sub 4} at high pressures are investigated using first-principles density functional calculations. The calculated equilibrium parameters are in good agreement with the available experimental and theoretical data. The obtained normalized volume dependence of high pressure is consistent with the previous experimental data investigated using high-pressure synchrotron x-ray diffraction. The complete elastic tensors and crystal anisotropies of the FeB{sub 4} are also determined in the pressure range of 0–100 GPa. By the elastic stability criteria and vibrational frequencies, it is predicted that the orthorhombic FeB{sub 4} is stable up to 100 GPa. In addition, the calculated B/G ratio reveals that FeB{sub 4} possesses brittle nature in the range of pressure from 0 to 100 GPa. The calculated elastic anisotropic factors suggest that FeB{sub 4} is elastically anisotropic. By using quasi-harmonic Debye model, the compressibility, bulk modulus, the coefficient of thermal expansion, the heat capacity, and the Grüneisen parameter of FeB{sub 4} are successfully obtained in the present work.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermoelectric and mechanical properties of multi-wall carbon nanotube doped Bi0.4Sb1.6Te3 thermoelectric material

Since many thermoelectrics are brittle in nature with low mechanical strength, improving their mechanical properties is important in fabrication of devices such as thermoelectric power generators and coolers. In this work, multiwall carbon nanotubes (CNTs) were incorporated into polycrystalline Bi0.4Sb1.6Te3 through powder processing, which increased the flexural strength from 32 MPa to 90 MPa. Electrical and thermal conductivities were both reduced in the CNT containing materials, leading to unchanged figure of merit. Dynamic Young s modulus and shear modulus of the composites were lower than the base material, which is likely related to the grain boundary scattering due to the CNTs.

mechanical strength↗