Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Accelerator experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Attaining freshwater and estuarine-water soil saturation in an ecosystem-scale coastal flooding experiment

Abstract Coastal upland forests are facing widespread mortality as sea-level rise accelerates and precipitation and storm regimes change. The loss of coastal forests has significant implications for the coastal carbon cycle; yet, predicting mortality likelihood is difficult due to our limited understanding of disturbance impacts on coastal forests. The manipulative, ecosystem-scale Terrestrial Ecosystem Manipulation to Probe the Effects of Storm Treatments (TEMPEST) experiment addresses the potential for freshwater and estuarine-water disturbance events to alter tree function, species composition, and ecosystem processes in a deciduous coastal forest in MD, USA. The experiment uses a large-unit (2000 m 2 ), un-replicated experimental design, with three 50 m × 40 m plots serving as control, freshwater, and estuarine-water treatments. Transient saturation (5 h) of the entire soil rooting zone (0–30 cm) across a 2000 m 2 coastal forest was attained by delivering 300 m 3 of water through a spatially distributed irrigation network at a rate just above the soil infiltration rate. Our water delivery approach also elevated the water table (typically ~ 2 m belowground) and achieved extensive, low-level inundation (~ 8 cm standing water). A TEMPEST simulation approximated a 15-cm rainfall event and based on historic records, was of comparable intensity to a 10-year storm for the area. This characterization was supported by showing that Hurricane Ida’s (~ 5 cm rainfall) hydrologic impacts were shorter (40% lower duration) and less expansive (80% less coverage) than those generated through experimental manipulation. Future work will apply TEMPEST treatments to evaluate coastal forest resilience to changing hydrologic disturbance regimes and identify conditions that initiate ecosystem state transitions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Development of Solid Isotope Harvesting Methods in Preparation for FRIB (Closeout Report)

This project developed the techniques necessary to isolate hydrolysable radiometals from irradiated accelerator components. It was a collaborative project headed by Dr. Jennifer Shusterman at Hunter College in coordination with Dr. Nick Scielzo at Lawrence Livermore National Laboratory and Dr. Gregory Severin at Michigan State University. To develop the methods for harvesting hydrolysable radiometals, both non-radioactive and radioactive experiments were conducted. Non-radioactive tests involved dissolving common accelerator materials (tungsten, copper, aluminum, and gold), adding trace amounts of Zr 4+ and Y 3+ , and then separating the added ions out again using a variety of column-based approaches. These methods were then tested on surrogate materials that were created by irradiating tungsten, copper, aluminum and gold foils with a low-purity 88 Zr beam at the National Superconducting Cyclotron Laboratory. The implanted 88 Zr (and co-implanted and daughter-product 88 Y) were recovered, validating the developed methods. MSU’s role in the project was to develop the chemistry for recovering Zr and Y from tungsten; build the target station for irradiating the foils; conduct the irradiations with the collaborators; to validate the tungsten methodology using the irradiated foils; and to disseminate the results.

07 ISOTOPE AND RADIATION SOURCES↗
NASA NTRS1990

The vibro-acoustic mapping of low gravity trajectories on a Learjet aircraft

The NASA LeRC Learjet aircraft is used to fly parabolic trajectories for carrying out in-flight microgravity experiments. To derive full benefit from data obtained in such experiments, it is not only required to understand the low- to moderate-frequency accelerations present but also necessary to characterize the broadband aircraft vibro-acoustic environment. A vibro-acoustic measurement program was conducted during a series of low-gravity trajectories flown on the Learjet. The fuselage and an experiment rack were instrumented with 13 channels of accelerometers and three channels of pressure transducers. The locations of these sensors were determined in order to build a time history of the dynamics involved in the flight of such a parabolic trajectory and thus determine the typical rigid-body and vibro-acoustic loading a payload would experience. The instrumentation, data acquisition sequence, and experimental results showing residual accelerations and high-frequency dynamics are presented. As suspected, the measurements revealed that the aircraft environment cannot simply be described in terms of the static level low-gravity g-vector obtained, but that it also must account for both rigid-body and high-frequency vibro-acoustic dynamics.

Grodsinsky, C. M.↗
DOE OSTI2026

A PRACTICAL ELECTRODIALYSIS MODEL FOR ACCELERATING SYSTEM DEVELOPMENT

Empirical optimization of electrodialysis (ED) is dependent on repetitive experiments with incremental adjustments, which is cost prohibitive at scale. While models can reduce the costs associated with optimization and scale-up, existing ED models are limited in application to specific use cases and tend to be developed for the exploration of specific transport phenomena. The field requires a practical system-level model, generalized for the broad range of ED systems. This work presents a modeling framework that enables rapid evaluation of membrane stack design, flow configuration, scale, and operational inputs. Across applications spanning 1 L to 5400 L; use of conventional and bipolar membranes; operation in continuous, batch and fed-batch modes; and feedstocks including seawater, brine, wastewater, and manure hydrolysate, the model achieves a mean R2 of 0.978 for concentration-time profiles and links design choices to techno-economic trade-offs, enabling cost-aware prioritization of system configurations.

Bipolar Membrane↗
DOE OSTI2024

Persistent Hot-Spot Mix in Cryogenic Direct-Drive Fusion Experiments

We show that an x-ray emission signature associated with acceleration phase mass injection correlates with poor experimental hot-spot convergence and a reduced neutron production relative to expectations. It is shown that with increased target mass as well as with higher-design adiabats, this signature is reduced, whereas with increased debris on the target the signature is increased. Here, we estimate that the vapor region in typical best designs may have up to 2x the assumed hydrogen mass at the start of deceleration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

First SELAP Algorithm Operational Experience of the New LLRF 3.0 RF Control System

The JLAB LLRF 3.0 system has been developed and is replacing the 30-year-old LLRF systems in the CEBAF accelerator. The LLRF system builds upon 25 years of design and operational RF control experience (digital and analog), and our recent collaboration in the design of the LCLSII LLRF system. The new system also incorporates a cavity control algorithm using a fully functional phase and amplitude locked Self Exciting Loop (SELAP). The first system (controlling 8 cavities) was installed and commissioned in August of 2021. Since then the new LLRF system has been operating with cavity gradients up to 20 MV/m, and electron beam currents up to 350 uA. This paper discusses the operational experience of the LLRF 3.0 SELAP algorithm along with other software and firmware tools like cavity and klystron characterization and quench detection.

Plawski, T. E.↗
NASA NTRS1980

Wind tunnel apparatus for translational oscillation experiments

A full-model translational oscillation apparatus has been developed for the wind-tunnel determination, in a wide speed range, of all three moment derivatives due to translational acceleration. The apparatus can be employed, in principle, for both vertical and horizontal oscillation experiments and can be used, therefore, to obtain moment derivatives due to alpha or beta, respectively. This information can be obtained directly if the model can be oscillated in the translational mode only, or indirectly - by utilizing some complementary information from angular oscillation experiments - if the model is allowed to also perform a small angular oscillation. The apparatus employs modern, fully digital instrumentation and an extensive use of auto and cross correlation techniques is made in the data reduction procedure

Orlik-Ruckemann, K. J.↗
NASA NTRS1993

NASA PPO microgravity projects support

Work progress is reported in brief. A summary of this information is provided below. An in-depth study was performed to evaluate a new European designed Borack Freezer/Cooler for possible shuttle middeck flight to support advanced protein crystal growth (APCG) experimentation. A statement of work was prepared for the design and development of a glovebox for proposed flight in the shuttle middeck. Work was also initiated to perform an analysis of low-g accelerometer data relative to Fluid Experiment System (FES) experiment options on the IML-1 mission. This work was undertaken in an effort to determine if abnormally low-g accelerations during the mission were responsible for anomalies which occurred during FES/Triglycine Sulfate (TGS) experiment operations. A comprehensive review was made on a revised edition of the Geophysical Fluid Flow Cell (GFFC) Operations and Maintenance (O&M) Manual.

Smith, Janice F.↗
NASA NTRS2016

Effort to Accelerate MBSE Adoption and Usage at JSC

This paper describes the authors' experience in adopting Model Based System Engineering (MBSE) at the NASA/Johnson Space Center (JSC). Since 2009, NASA/JSC has been applying MBSE using the Systems Modeling Language (SysML) to a number of advanced projects. Models integrate views of the system from multiple perspectives, capturing the system design information for multiple stakeholders. This method has allowed engineers to better control changes, improve traceability from requirements to design and manage the numerous interactions between components. As the project progresses, the models become the official source of information and used by multiple stakeholders. Three major types of challenges that hamper the adoption of the MBSE technology are described. These challenges are addressed by a multipronged approach that includes educating the main stakeholders, implementing an organizational infrastructure that supports the adoption effort, defining a set of modeling guidelines to help engineers in their modeling effort, providing a toolset that support the generation of valuable products, and providing a library of reusable models. JSC project case studies are presented to illustrate how the proposed approach has been successfully applied.

Wang, Lui↗
DOE OSTI2021

Accelerate Nuclear Research and Development by Reducing Time and Cost Spend in the Pre-conceptual Design Phase of Advanced Reactor Experiments

The design process of every new concept, such as advanced nuclear reactors or associated experiments, starts with the pre-conceptual design phase. In this phase, the viability of a wide range of design options needs to be assessed quickly, to understand the operating envelope and its feasibility. A variety of physics models (thermal-hydraulics, neutronics, mechanical design, etc.) has to be considered at this very first design stage and optimum component sizes and materials (e.g. heat exchangers, piping, turbomachinery, coolant type, etc.) have to be chosen for a given set of boundary conditions (e.g. heat source, heat sink, flow rate, etc.). Detailed solutions such as provided by high fidelity methods like computational fluid dynamics (CFD), Monte Carlo methods, etc. and even lower fidelity tools such as system or subchannel codes, etc. are usually not used during the pre-conceptual design due to the relatively long time needed to create input models, the computational time to obtain a solution and the lack of flexibility to quickly investigate different combinations of components, individual component sizes and material properties. High fidelity tools are usually only employed in the conceptual design and later phases once a base concept has been identified during the pre-conceptual design stage. The current practice during the pre-conceptual design stage is that analysts collect the needed equations, material properties, closure laws, etc. and create ad-hoc solutions form scratch for every new problem. There clearly is a lack of a flexible scoping tool that can be used during pre-conceptional design before higher fidelity tools (as described above) come into play. To reduce user errors in ad-hoc solutions and increase fidelity and efficiency, this project aims to investigate and develop a user-friendly scoping tool to address the thermal-hydraulic designing needs during preconceptual experiment design, i.e. Thermal-hydraulic Research Universal Scoping Tool (TRUST). The success of TRUST will provide the nuclear engineers with an easy-to-use and affordable calculator for early reactor system design and optimization.

42 ENGINEERING↗
NASA NTRS1996

Active Vibration Isolation of Microgravity Experiments with Spring Umbilicals Using an Electrodynamic Actuator

Microgravity experiments will require active vibration isolation in the low to mid frequency range of 0.1 Hz to 10 Hz. Approximately two orders of acceleration reduction (40 dB) will be required. Previous works have reported results for accelerations transmitted through the umbilical. This paper describes experimental and theoretical results for vibration isolation in one dimension (horizontal) where the simulated experiment is connected to the spacecraft by a spring umbilical. The experiment consisted of a spacecraft (shaker), experiment (mass), umbilical, accelerometer, control electronics, and Lorentz actuator. The experiment mass was supported in magnetic bearings to avoid any stiction problems. Acceleration feedback control was employed to obtain the vibration isolation. Three different spring umbilicals were employed. Acceleration reductions on the order of 40 dB were obtained over the frequency range of 0.1 Hz to 10 Hz. Good agreement was obtained between theory and experiment.

Banerjee, B. B.↗
DOE OSTI2021

Accelerator Real-time Edge AI for Distributed Systems (READS) (Proposal)

Over the last decade, Machine Learning (ML) technologies have slowly made their way into the accelerator community. Rapid advances in recent years in deep learning, particularly reinforcement learning for control system applications and the accessibility of deep learning in embedded hardware, have generated renewed interest and spawned a number of applications. The Fermilab Accelerator Complex, shown in Fig. 1, has provided High Energy Physics (HEP) experiments with proton beams for nearly fifty years. The current focus of the laboratory is its world-class experimental program at the intensity frontier. While increasing beam intensity certainly presents its own challenges, preserving beam size while minimizing beam losses – particles lost through interactions with the beam vacuum pipe – turns out to be, in many ways, the main challenge. The accelerator is controlled via a complex system of hundreds of thousands of devices. Enabling fine tuning and real-time optimization of their parameters using ML methods and stepping beyond experience-based reasoning of human operators are key to the success of future intensity upgrades. Our objective will be to integrate ML into accelerator operations and furthermore, provide an accessible framework, which can also be used by a broad range of other accelerator systems with dynamic tuning needs.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Normality of I-V Measurements Using ML

There is an increased interest in instrument-computing ecosystems (ICEs) that support science workflows empowered by AI-automated experiments and computations in diverse areas. In particular, electrochemistry ICEs are promising for accelerating the design and discovery of electrochemical systems for energy storage and conversion, by automating significant parts of workflows that combine synthesis and characterization experiments with computations. They require the integration of flow controllers, solvent containers, pumps, fraction collectors, and potentiostats, all connected to an electrochemical cell, as illustrated in Fig. 1. These are specialized instruments with custom software that is not originally designed for network integration. We developed network and software solutions for electrochemical workflows that adapt system and instrument settings in real-time for multiple rounds of experiments. In particular, we developed Python wrappers for Application Programming Interfaces (APIs) of instrument commands and Pyro client-server modules that enable them to be executed from remote computers. The entire workflow is orchestrated by a Jupyter notebook running on a remote computer.

Al Najjar, Anees↗
DOE OSTI2023

Computationally Guided Design of Multiple Impurities Tolerant Cathode for Solid Oxide Fuel Cell Applications

Solid oxide fuel cells (SOFCs) have been recognized as promising candidates in the demand of reducing the dependence on fossil fuels, which is one of the solutions to the threat of global warming. It was reported that the direct chemical-to-electrical energy conversion in SOFCs comes with negligible emission of greenhouse gases and up to 60% working efficiency. SOFC has unique advantages over traditional power generation technologies and other types of fuel cells due to the use of relatively inexpensive materials, low sensitivity to poisoning impurities in fuels, relatively high conversion efficiency, and fuel flexibility (like carbon-based fuels). However, during the SOFC operation, the cathode is exposed to intrinsic and extrinsic airborne contaminants at high temperatures (600–900°C), leading to their reaction with electrode materials, irreversible chemical and structural changes, and electrochemical performance degradation. of which CO2, SO2, Cr6+ and H2O are known to be concerns. Thus, developing a comprehensive understanding of the multiple impurities poisoning of SOFC cathodes in the presence of single or multiple impurities is necessary to address the long-term degradation of the SOFC cathode systems at operating conditions. An integrated computational and experimental approach has been utilized in the current work aiming at the comprehensive investigation of the cathode materials under single or multiple impurities poisoning effects, understanding the multiple impurities poisoning mechanism(s), and improving the long-term durability of the SOFC cathodes to develop better performing impurity-tolerant cathode materials. We first examined the agreement between the simulation approach and the experimental observations at various atmospheric and temperature conditions to confirm the reliability of CALPHAD for poisoning simulations in these cathodes. Then, using this approach, we investigated the accelerated testing protocol, which has become the standard method for conducting impurity poisoning experiments involving these cathode materials. We found our simulation approach is able to predict in which systems, i.e., cathode material and treatment environment, the accelerated testing protocols reflect actual operating conditions. Finally, in-depth simulations were done for these three candidate cathodes under different experimental conditions and suggested directions toward alternative cathode materials that have superior impurity tolerance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

PIP-II 800 MeV Proton Linac Beam Pattern Generator

The PIP2 IT Beam Pattern Generator is the system that synchronizes beam injection and the RF systems between the PIP2 LINAC to the Booster. The RF frequencies of these two accelerator systems are not harmonically related. Synchronization is accomplished by controlling two MEBT Beam Choppers, which select 162.5MHz beam bunches from the LEBT and RFQ to produce an appropriate reduced beam bunch pattern that enables bucket-to-bucket transfer to the Booster RF at 46.46MHz (84th harmonic). This chopping pattern also reduces the beam current to an average of 2mA over the Booster injection, matching the Linac nominal beam current. The BPG also generates the RF frequency/phase reference which the Booster will phase lock to during injection. The BPG is fully programmable, allowing for arbitrary beam patterns with adjustable timing parameters, having a fine adjustment resolution of 38ps. The latter is accomplished using digital signal processing techniques. This paper discusses the design of the BPG, its construction, test results, and operational experience after being integrated into the PIP2 IT test accelerator and concludes with a discussion of the system’s performance and future plans.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

The large-area hybrid-optics CLAS12 RICH: First years of data-taking

The CLAS12 deep-inelastic scattering experiment at the upgraded 12 GeV continuous electron beam accelerator facility of Jefferson Lab conjugates luminosity and wide acceptance to study the 3D nucleon structure in the yet poorly explored valence region, and to perform precision measurements in hadron spectroscopy. A large area ring-imaging Cherenkov detector has been designed to achieve the required hadron identification in the momentum range from 3 GeV/c to 8 GeV/c, with the kaon rate about one order of magnitude lower than the rate of pions and protons. The adopted solution comprises aerogel radiator and composite mirrors in a novel hybrid optics design, where either direct or reflected light could be imaged in a high-packed and high-segmented photon detector. The first RICH module was assembled during the second half of 2017 and installed at the beginning of January 2018, in time for the start of the experiment. The second RICH module, planned with the goal to be ready for the beginning of the operation with polarized targets, has been timely built despite the complications caused by the pandemic crisis and successfully installed in June 2022. Finally, the detector performance is here discussed with emphasis on the operation and stability during the data-taking, calibration and alignment procedures, reconstruction and pattern recognition algorithms, and particle identification.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS2005

Progress on the Plasmoid Thruster Experiment (PTX)

A plasmoid, also called a compact toroid, is a compact plasma structure with an integral magnetic field, that may be categorized according to the relative strength of the poloidal and toroidal magnetic field (Bp and Bt, respectively). An object with Bp/Bt much greater than 1 is called a Field Reverse Configuration (FRC); if Bp = Bt, it is called a Spheromak. The plasmoid thruster is a pulsed inductive device which operates by repetitively producing plasmoids that are accelerated and ejected at high velocity. As the process is inductive, this thruster avoids the problem of electrode erosion. Also, the magnetic structure of the plasmoid should suppress thermal and mass losses to the wall, and improve detachment of the plasma exhaust from the thruster. This concept should be capable of producing an Isp of 5,000 seconds and greater, with thrust densities of order 10(exp 5) N/sq m. The plasmoid thruster consists chiefly of a conical theta-pinch coil. Propellant is introduced onto a bias magnetic field, produced by an auxiliary coil, and is then pre-ionized, freezing in the magnetic field. The theta-pinch coil is then energized producing a field aligned anti- parallel to the bias field. The reversed field reconnects with the bias field to form the plasmoid. The magnetic pressure of the reversed field accelerates the plasmoid out of the thruster . A series of experiments have been conducted on the PTX device, which consisted of a single turn conical theta-pinch coil, driven by a 560 nF, 35 kV capacitor bank, which rang at a frequency of 500 kHz, and served all three functions required for formation: pre-ionization, bias field loading, and field reversal. Initial ionization was found to occur in an annular region at the exit plane of the coil, and was found to be reproducible with a variety of gases, including H2, D2, Ar, and an H2/N2 mixture (75% / 25%). A fast gas valve for injecting propellant has been tested, as well as a ringing pre-ionization circuit (operating at 5 Mhz) to better control the plasmoid formation. Velocities as high as 20 km/s have been measured for a plasmoid propagating into a static back-fill of neutral gas. Magnetic field and density measurements indicate that the plasmoid retains its structure well into the down-stream exhaust region, and that it is capable of pushing a dense cloud of neutral gas in front of it. Further experiments will focus on the effects of coil geometry and bias-field strength on the performance of the device. A high-power solid-state switching system is being developed in order to replace the spark-gap switch.

Martin, Adam↗
DOE OSTI2026

Updating the BNB Flux Prediction at SBND

Precise, accurate neutrino flux predictions for neutrino beam experiments are crucial for physics results. Flux uncertainties contribute significantly to the total systematic uncertainties seen in modern accelerator neutrino measurements such as cross sections, oscillations, and BSM studies.. For over a decade, experiments utilizing Fermilab’s Booster Neutrino Beam (BNB) have relied on the 2009 MiniBooNE flux prediction. However, the high-statistics era of the Short-Baseline Neutrino (SBN) program, with both SBND and ICARUS now operating, demands a modernized flux model and framework. While SBND is using the MiniBooNE flux model for its Generation 1 analyses, including many upcoming cross section measurements, future work will be based on a new flux model. In this talk, the ongoing work towards this new model will be outlined, including a new simulation framework (G4BNB), a new evaluation of model parameters from hadron scattering data, and a new framework for evaluating systematic uncertainties (BNBFP). Additionally, expansions to the flux model to include BSM contributions from neutral mesons will be discussed, as well as the PRISM capabilities of SBND to observe a wide range of off axis angles of the neutrino beam.

Paton, Josephine [Fermilab]↗