Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ARTIFACTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70

Performance Evaluation of an Offshore Wave Measurement Buoy in Monochromatic Waves

The accurate measurement of waves underpins marine energy resource characterization, device design, and project development. Datawell wave buoys are widely deployed and have long served as a trusted standard for wave measurements. We quantify the measurement performance, including wave elevation and energy flux estimation, of a Datawell DWR-MkIII buoy using prescribed monochromatic heave motions on a large-amplitude six-degree-of-freedom motion platform at the National Laboratory of the Rockies, assuming the buoy behaves as an ideal wave follower. Commanded motions were validated with an optical motion tracking system while buoy elevation and raw acceleration were recorded. Wave elevations were propagated to wave energy flux estimation using four methods, including one frequency-domain method and three time-domain methods. The Bayesian optimization was applied for design of experiments, and records from three test sites were also applied and evaluated in the present study. Results show two error regions within the nominal period range of 1.6 s to 30 s. For wave periods between 5 s and 25 s, the buoy provides accurate wave height measurements. For short periods less than 5 s, the 1.28 Hz sampling frequency induces sub-Nyquist artifacts that bias elevation and can drive maximum energy flux estimation errors above 100%. For long periods exceeding 25 s, the buoy reported elevation is underpredicted with error depending on period but relatively independent of wave height, with maximum wave height and wave energy flux errors reaching 64% and 87%, respectively. Furthermore, analysis of three field-derived cases shows that frequency-domain estimates at 1.28 Hz agree within 2% of the corresponding 100 Hz estimates, while larger method-dependent differences are observed for the Hilbert method.

16 TIDAL AND WAVE POWER↗

Analysis of OpenMP 4.5 Offloading in Implementations: Correctness and Overhead

The OpenMP language features have been evolving to meet the rapid development in hardware platforms. This journal focuses on evaluating implementations of OpenMP 4.5 target offload features in compilers such as Clang, XL and GCC that are an integral part of the software harness on supercomputers and clusters. We use Summit (Top supercomputer in the world as of November 2018) as one of our experimental setup. Such an effort is particularly critical on such supercomputers as that is being widely used by application developers to run their scientific codes at scale. Our tests not only evaluate the OpenMP implementations but also expose ambiguities within the OpenMP 4.5 specification. We also assess the overhead of the different OpenMP runtimes in relationship to the different directives and clauses. This helps in assessing the interaction of different OpenMP directives independent of other application artifacts. We are aware that the implementations are constantly evolving and Summit is advertised as having only partial OpenMP 4.x support. This is a synergistic effort to help identify and fix bugs in features’ implementations that are required by applications and prevent deployment delays later on. Going forward, we also plan to interact with standard benchmarking organizations like SPEC/HPG to donate our tests and mini-apps/kernels for potential inclusion in the next release versions of SPEC benchmark suite.

97 MATHEMATICS AND COMPUTING↗

Scaling of heat transport near onset in rapidly rotating convection

Here, we consider the scaling of heat transport in the geostrophic regime of rotating Rayleigh–Bénard convection near onset for small Ekman number Ek from the perspective of weakly nonlinear theory. We show that available heat transport data from numerical simulation [1] for Ek < 10 -5 for Pr = 1 are consistent with weakly nonlinear theory for ϵ = Ra / Ra c - 1 < 1. In particular, we show that the numerical data are consistent with Nu - 1 = aϵ + bϵ 2 with a ≈ 2 and b ≈ 3 with weak dependence of the coefficients on Ek. The coefficient a is consistent with calculations of weakly nonlinear theory and with experimental data at much higher Ek. The positive sign of b is also suggested by those experimental data. The magnitude and trend of the numerical data for larger Ra are consistent with experimental data with similar Pr ~ 1. The steep scaling of Nu ~ (Ra / Ra c ) 3 noted elsewhere for Ra / Ra c < 2 is shown to be an artifact of being close to onset where the effective power-law slope depends sensitively on the magnitude of the coefficients a and b. Similar arguments apply to Pr = 7 numerical data although the weakly nonlinear expansion appears valid for a smaller range of ϵ than in the Pr = 1 case.

58 GEOSCIENCES↗

The Kalahari sediments and hominins in southern Africa

In this study, the temporal coupling of the structural evolution of the Kalahari Basin and the accumulation of the Kalahari Group sediments has been an accepted paradigm leading to the assumption that the Kalahari group sediments have been accumulating gradually since the mid-Cretaceous. Here we review the first actual ages for the Kalahari Group based on cosmogenic ages from six geological localities. These results demonstrate that Kalahari Basin infill was a more dynamic process than previously thought and that the Kalahari Group sediments are mostly Plio-Pleistocene in age (~4 Ma to 1–2 Ma). The hiatus between the initial structural subsidence of the basin, during the Cretaceous, and the general young age of the investigated sediments, implies a dynamic landscape in which significant phases of erosion occurred during the Mesozoic and Cenozoic. The magnitude of erosion is manifested by the fact that in many locations Kalahari Neogene to Quaternary sediments overlie Precambrian basement. The age of the present infill of the Kalahari thus falls within the temporal range of the genus Homo. In light of this new understanding, we provide a review of the archaeological evidence from the Kalahari Basin and along its southern fringe. Initial hominin presence is found at Wonderwerk Cave during the Olduvai Event and there is subsequent high-density occupation along the southern fringe of the Kalahari Basin during the Acheulean and the Fauresmith. Middle Stone Age occupation is limited to localities of limited size and small artifact counts and it appears that the focus of human occupation, particularly in the later stages of the Middle Stone Age, shifts southward, including along the coastal regions.

58 GEOSCIENCES↗

Quality control and crop characterization framework for multi-temporal UAV LiDAR data over mechanized agricultural fields

Recent developments in remote sensing are enabling automatic, high resolution, and non-destructive survey of agriculture fields, providing the key basis for advancing plant breeding. Among the used remote sensing modalities, LiDAR has attracted wide attention for its ability to directly provide accurate 3D information. Despite the increasing utilization of LiDAR technology in phenotyping, there is still a lack of effective quality control strategies, in particular, quality control of LiDAR data collected on a multi-temporal basis. This study proposes a targetless framework for multi-temporal LiDAR data quality control and crop characterization in mechanized agricultural fields. Features extracted from the fields – terrain patches and row/alley locations – are utilized for evaluating the vertical and planimetric relative accuracy of the point clouds. Row/alley locations in the field are automatically identified from the point clouds based on the assumption that higher point density and/or higher elevation correspond to plant locations. The performance of the proposed quality control strategies is evaluated using multi-temporal datasets collected in agricultural fields of different sizes, orientation, crops, and growth stages. The result shows that the net vertical and planimetric discrepancies between multi-temporal point clouds are ±3 cm and ±8 cm, respectively. While the former reflects the actual accuracy of the point clouds, the latter is a combined effect of the LiDAR point cloud accuracy, rasterization artifacts, crop type, growth pattern, and wind condition during data acquisition. In terms of row and alley detection, the result shows that the proposed strategy achieves high performance and can deal with different planting orientation, crop types, growth stages, canopy cover, and planting density. In conclusion, this study presents a quality control framework for multi-temporal LiDAR data. Finally, the row and alley detection leads to automated extraction of plots, and hence facilitates the use of remotely sensed data for automated phenotyping.

54 ENVIRONMENTAL SCIENCES↗

Correlation of Surface Acoustic Wave (SAW) force myography sensor output with elbow joint torque

Accurate assessment of skeletal muscle forces and net joint torque is essential for preventing fatigue-related injuries, optimizing physical training, and monitoring disease progression in neuromuscular conditions. However, existing joint torque evaluation techniques are hindered by limited portability and high operational costs, confining their use to controlled laboratory or clinical settings. Despite substantial advances in wearable joint torque estimation systems, ongoing challenges such as power constraints, bulky wired setups, and susceptibility to environmental or motion artifacts underscore the urgent need for truly batteryless, wireless solutions deployable in real-world settings. This paper proposes a novel surface acoustic wave (SAW)-based force myography (FMG) system for noninvasive measurement of joint torque, validated against a gold-standard electromechanical dynamometer. The approach uses a single SAW sensor embedded in an armband to detect volumetric biceps brachii changes, with a second-order polynomial mapping sensor output and elbow angle to torque. Seven participants were tested in both isometric (15°–90°) and isokinetic (10°/s and 20°/s) supinated elbow flexion tasks. Under isometric conditions, subject-specific calibration achieved a normalized root-mean-square error (NRMSE) of 13.6% ± 6.0% and R 2 = 0.834 ± 0.180, while a group-level model yielded 14.4% ± 6.8% and 0.808 ± 0.208, respectively. For isokinetic trials, the group model produced an NRMSE of 24.1% ± 6.6% at 10°/s and 24.9% ± 08.9% at 20°/s, highlighting the feasibility of using a single-sensor SAW-FMG setup across different speeds. Because SAW devices support wireless, battery-free operation, the proposed system offers a pathway to portable, real-time monitoring for sports medicine, rehabilitation, and clinical diagnostics.

36 MATERIALS SCIENCE↗

Subsurface microbial communities as a tool for characterizing regional-scale groundwater flow

Subsurface microbial community distribution patterns are influenced by biogeochemical and groundwater fluxes and may inform hydraulic connections along groundwater-flow paths. This study examined the regional-scale microbial community of the Death Valley Regional Flow System and evaluated whether subsurface communities can be used to identify groundwater-flow paths between recharge and discharge areas. Samples were collected from 36 sites in three groundwater basins: Pahute Mesa–Oasis Valley (PMOV), Ash Meadows (AM), and Alkali Flat–Furnace Creek Ranch (AFFCR). Microbial diversity within and between communities varied by location, and communities were separated into two overall groups that affiliated with the AM and PMOV/AFFCR basins. Network analysis revealed patterns between clusters of common microbes that represented groundwaters with similar geochemical conditions and largely corroborated hydraulic connections between recharge and discharge areas. Null model analyses identified deterministic and stochastic ecological processes contributing to microbial community assemblages. Most communities were more different than expected and governed by dispersal limitation, geochemical differences, or undominating processes. However, certain communities from sites located within or near the Nevada National Security Site were more similar than expected and dominated by homogeneous dispersal or selection. Overall, the (dis)similarities between the microbial communities of DVRFS recharge and discharge areas supported previously documented hydraulic connections between: (1) Spring Mountains and Ash Meadows; (2) Frenchman and Yucca Flat and Amargosa Desert; and (3) Amargosa Desert and Death Valley. However, only a portion of the flow path between Pahute Mesa and Oasis Valley could be supported by microbial community analyses, likely due to well-associated artifacts in samples from the two Oasis Valley sites. This study demonstrates the utility of combining microbial data with hydrologic, geologic, and water-chemistry information to comprehensively characterize groundwater systems, highlighting both strengths and limitations of this approach.

54 ENVIRONMENTAL SCIENCES↗

Laser Ablation-Capillary Absorption Spectroscopy: A novel approach for high throughput and increased spatial resolution measurements of δ 13 C in plant-soil systems

Spatial and temporal heterogeneity of nutrient exchange within the rhizosphere is a topic of increasing interest, although challenging to study due to limits in existing analytical capabilities. Here, we developed and demonstrated a new approach applying laser ablation sample introduction to capillary absorption spectroscopy (LA-CAS) to characterize carbon isotopic distribution within plant tissues, rhizosphere, and soil. We exposed switchgrass plants to 13 CO 2 to allow tracing of 13 C-labelled photosynthates within plant biomass and into the associated soil. The LA-CAS methods we describe leverage continuous measurements of a sample stream derived from laser ablation line scans (10-25 µm in width) over a sample surface which enables the user to produce an isotope map with a) higher data density or b) over larger spatial areas versus previously existing techniques. This versatility of LA-CAS is assessed through testing of a range of laser parameters (spot size, scan rates) on various materials (soil, plant biomass/tissues, and rhizosphere). Here, we demonstrate the ability of LA-CAS to provide near instantaneous $δ$ 13 C measurements over isotopically distinct surfaces to enable high spatially resolved mapping of 13 C-labelled material within the rhizosphere. Applying LA-CAS analysis to plant biomass, we observed higher $δ$ 13 C values concentrated within phloem structures, consistent with localized photosynthate transport. When mapping across the rhizosphere, 13 C-enriched soil was typically present within 5-10µm of root boundaries with a steep spatial increase in $δ$ 13 C when the scan approached the middle of the root. As with all LA approaches, care is required to ensure accurate results as phenomena linked to ablation, combustion, and isotopic measurement can impart artifacts if not carefully controlled. Still, taken as a whole, our demonstrations highlight the increased sample throughput, improved data density, and enhanced $δ$ 13 C capability of LA-CAS versus other LA techniques and emphasize the role this method can play in future plant and rhizosphere related studies.

59 BASIC BIOLOGICAL SCIENCES↗

Development of in-situ high-voltage and high-temperature stressing capability on atomic force microscopy platform

Reliability has become an increasingly important issue as photovoltaic technologies mature. However, researching reliability at the nanometer scale is in its infancy; in particular, in-situ studies have not been reported to date. Here, to investigate potential-induced degradation (PID) of solar cell modules, we have developed an in-situ stressing capability with applied high voltage (HV) and high temperature (HT) on an atomic force microscopy (AFM) platform. We designed a sample holder to simultaneously accommodate 1000-V HV and 200 degrees C HT stressing. Three technical challenges have been overcome along with the development: thermal drift at HT, HV interference with measurement, and arc discharge caused by HV. We demonstrated no observable measurement artifact under the stress conditions. Based on our in-situ stressing AFM, Kelvin probe force microscopy potential imaging revealed the evolution of electrical potential across the junction along with the PID stressing time, which provides vital information to further study the PID mechanism.

14 SOLAR ENERGY↗

Topographic and nanomechanical mapping of plutonium surfaces

Atomic force microscopy of gallium-stabilized δ-phase plutonium coupons has been used to map their topography and qualitative mechanical character, including Derjaguin-Muller-Toporov modulus, adhesion, deformation, and dissipation. Initial topographical results demonstrate that the plutonium surface is considerably rough and heterogeneous. Qualitative nanomechanical mapping revealed distinct striation patterns that are not observed in the topography images. Further investigation of the striations in the nanomechanical modes of imaging suggest that they are not measurement artifacts, or plutonium specific features. Similar investigations of stainless steel surfaces established a strong correlation between the mechanical working of the surface (i.e. cutting and grinding) and the appearance of the striations. Reimaging of the plutonium surface after moderate oxidation occurring within an inert Ar atmosphere (~1 ppm O 2 ) over the course of 13 months revealed a diminished striation pattern. It is suggested that surface stress/strain induced by the mechanical working of the metal surfaces results in the patterns of variable modulus, adhesion, deformation, and dissipation, and that these patterns are affected by the chemical changes and aging of the plutonium surface.

36 MATERIALS SCIENCE↗

Effect of pressure on TATB and LX-17 thermal decomposition

Thermal decomposition of TATB (1,3,5-triamino-2,4,6-trinitrobenzene) and its formulation LX-17 is studied at pressures from 0.1 to 7 MPa for both isothermal heating at 340 K and ramped heating at 1 to 6 K min -1 . Conditions that eliminate self-heating are thoroughly explored to avoid experimental artifacts. The increase in pressure accelerates the rate of decomposition by only about 10 %, but it substantially increases the enthalpy of the reaction, presumably because of longer volatile product residence times in the heated zone. The narrowness of the decomposition profile and the acceleratory phase during isothermal pyrolysis are consistent with a multistep autocatalytic mechanism, and the lack of a significant pressure effect suggests that the autocatalytic species have low volatility. The apparent activation energy is about 210 kJ/mol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Boosting Noise2Inverse via enhanced model selection for denoising computed tomography data

Synchrotron-based x-ray tomographic imaging enables the examination of the internal structure of materials at high spatial and temporal resolution. Experimental constraints can impose dose and time limits on the measurements, introducing a higher level of noise and artifacts in the reconstructed images. Deep learning has emerged as a powerful tool to remove noise from reconstructed images. Recently, the Noise2Inverse method was designed specifically for denoising reconstructed images without requiring paired noisy and clean images. This method creates multiple statistically independent reconstructions used to pair the data in which training involves transforming one reconstruction into the other, and vice versa. Originally designed to be used after a fixed number of epochs, we see in practice that this approach may not produce the optimal model and may unnecessarily waste computational resources. Therefore, we propose an alternative method of identifying the best model during training that aligns with the Noise2Inverse method. During validation, we compare the model output of the multiple reconstructions among each other. We hypothesize that the best model is the one that produces images with the highest similarity, implying a convergence in the predicted material properties and absorption values. To compare model outputs, we consider the absolute error, square error, structural similarity index (SSIM), peak signal-to-noise ratio (PSNR), and cosine similarity. We evaluate our method on two simulated tomography datasets and two, real-world, low-contrast, high-energy x-ray tomography datasets. We show our approach is more effective at determining the best model, up to an increase of 12.50% and 12.53% in SSIM and PSNR, respectively, while only requiring a fifth of the training time compared to the original approach.

CT↗

Electron-beam-induced-current and active secondary-electron voltage-contrast with aberration-corrected electron probes

The ability to map out electrostatic potentials in materials is critical for the development and the design of nanoscale electronic and spintronic devices in modern industry. Electron holography has been an important tool for revealing electric and magnetic field distributions in microelectronics and magnetic-based memory devices, however, its utility is hindered by several practical constraints, such as charging artifacts and limitations in sensitivity and in field of view. In this article, we report electron-beam-induced-current (EBIC) and secondary-electron voltage-contrast (SE-VC) with an aberration-corrected electron probe in a transmission electron microscope (TEM), as complementary techniques to electron holography, to measure electric fields and surface potentials, respectively. These two techniques were applied to ferroelectric thin films, multiferroic nanowires, and single crystals. Electrostatic potential maps obtained by off-axis electron holography were compared with EBIC and SE-VC to show that these techniques can be used as a complementary approach to validate quantitative results obtained from electron holography analysis.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

3D reconstruction of the magnetic vector potential using model based iterative reconstruction

Lorentz transmission electron microscopy (TEM) observations of magnetic nanoparticles contain information on the magnetic and electrostatic potentials. Vector field electron tomography (VFET) can be used to reconstruct electromagnetic potentials of the nanoparticles from their corresponding LTEM images. The VFET approach is based on the conventional filtered back projection approach to tomographic reconstructions and the availability of an incomplete set of measurements due to experimental limitations means that the reconstructed vector fields exhibit significant artifacts. In this paper, we outline a model-based iterative reconstruction (MBIR) algorithm to reconstruct the magnetic vector potential of magnetic nanoparticles. We combine a forward model for image formation in TEM experiments with a prior model to formulate the tomographic problem as a maximum a-posteriori probability estimation problem (MAP). The MAP cost function is minimized iteratively to determine the vector potential. Here, a comparative reconstruction study of simulated as well as experimental data sets show that the MBIR approach yields quantifiably better reconstructions than the VFET approach.

36 MATERIALS SCIENCE↗

Towards bend-contour-free dislocation imaging via diffraction contrast STEM

Dislocation imaging using transmission electron microscopy (TEM) has been an invaluable tool for characterizing crystallographic defects in metals. Compared to conventional TEM imaging, diffraction contrast imaging scanning transmission electron microscopy (DCI STEM) with appropriate setting can provide better defect contrast with almost negligible bend contour artifacts, enabling more effective analysis of dislocation structures. Here, we investigated why STEM can suppresses bend contour, and how dislocation contrast behaves along with different STEM imaging parameters. Using a body-centered cubic HT-9 ferritic/martensitic alloy as an example, a simple procedure and operational theory are described at the beginning to help set up DCI STEM experiments. Comparing with conventional TEM and the STEM strictly complying with the principle of reciprocity, we found that a pair of STEM convergence and collection semi-angles, α S and β S , a few milliradians in size is essential for bend-contour-free defect imaging. It works in concert such that the convergence STEM probe opens up the reciprocal space, and then a comparable collection region evens out the rocking-curve oscillation and alleviates bend contours from the reciprocal space. This fundamental advantage is unique in DCI STEM. Practical guidelines regarding STEM parameters and specimen orientation and thickness are then provided for DCI STEM dislocation imaging. Lastly, we show that coupling DCI STEM with spectrum images of electron energy loss spectroscopy and of energy-dispersive X-ray Spectroscopy offers a comprehensive characterization of crystallographic defects and chemical information of complex microstructures.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

CD45{sup low}c-Kit{sup high} cells have hematopoietic properties in the mouse aorta-gonad-mesonephros region

Long-term reconstituting hematopoietic stem cells first arise from the aorta of the aorta-gonad-mesonephros (AGM) region in a mouse embryo. We have previously reported that in cultures of the dispersed AGM region, CD45{sup low}c-Kit{sup +} cells possess the ability to reconstitute multilineage hematopoietic cells, but investigations are needed to show that this is not a cultured artifact and to clarify when and how this population is present. Based on the expression profile of CD45 and c-Kit in freshly dissociated AGM cells from embryonic day 9.5 (E9.5) to E12.5 and aorta cells in the AGM from E13.5 to E15.5, we defined six cell populations (CD45{sup -}c-Kit{sup -}, CD45{sup -}c-Kit{sup low}, CD45{sup -}c-Kit{sup high}, CD45{sup low}c-Kit{sup high}, CD45{sup high}c-Kit{sup high}, and CD45{sup high}c-Kit{sup very} {sup low}). Among these six populations, CD45{sup low}c-Kit{sup high} cells were most able to form hematopoietic cell colonies, but their ability decreased after E11.5 and was undetectable at E13.5 and later. The CD45{sup low}c-Kit{sup high} cells showed multipotency in vitro. We demonstrated further enrichment of hematopoietic activity in the Hoechst dye-effluxing side population among the CD45{sup low}c-Kit{sup high} cells. Here, we determined that CD45{sup low}c-Kit{sup high} cells arise from the lateral plate mesoderm using embryonic stem cell-derived differentiation system. In conclusion, CD45{sup low}c-Kit{sup high} cells are the major hematopoietic cells of mouse AGM.

60 APPLIED LIFE SCIENCES↗

The effects of chemical fixation on the cellular nanostructure

Chemical fixation is nearly indispensable in the biological sciences, especially in circumstances where cryo-fixation is not applicable. While universally employed for the preservation of cell organization, chemical fixatives often introduce artifacts that can confound identification of true structures. Since biological research is increasingly probing ever-finer details of the cellular architecture, it is critical to understand the nanoscale transformation of the cellular organization due to fixation both systematically and quantitatively. In this work, we employed Partial Wave Spectroscopic (PWS) Microscopy, a nanoscale sensitive and label-free live cell spectroscopic-imaging technique, to analyze the effects of the fixation process through three commonly used fixation protocols for cells in vitro. In each method investigated, we detected dramatic difference in both nuclear and cytoplasmic nanoarchitecture between live and fixed states. But significantly, despite the alterations in cellular nanoscale organizations after chemical fixation, the population differences in chromatin structure (e.g. induced by a specific chemotherapeutic agent) remains. In conclusion, we demonstrated that the nanoscale cellular arrangement observed in fixed cells was fundamentally divorced from that in live cells, thus the quantitative analysis is only meaningful on the population level. This finding highlights the importance of live cell imaging techniques with nanoscale sensitivity or cryo-fixation in the interrogation of cellular structure, to complement more traditional chemical fixation methods. - Highlights: • PWS was employed to monitor fixation process for the same cells in vitro. • Dramatic changes in cellular nanostructure were observed after fixation. • However, the population difference of chromatin structure remains after fixation.

60 APPLIED LIFE SCIENCES↗

Narrowband signals recorded near a moulin that are not moulin tremor: a cautionary short note

Geophysicists that deploy seismic sensors in ablation zones of glaciers and ice sheets to record glaciogenic signatures can confront recording challenges caused by instrument melt-out or tilt. These challenges often require installing sensors in boreholes to delay melt-out, or securing sensors to structures that improve coupling. We show that some of these structures that were buried near a moulin at a snow-free site in the ablation zone of the Western Greenland Ice Sheet resonated as they became exposed, and caused their geophones to record temporally evolving, narrowband signals that mimic features of glaciogenic sources like moulin tremor. We quantify these artifacts with a mechanical model that shows instruments undergo structural resonance as they melt-out, at exposure rates that we predict from an ablation model (RACMO). These models reproduce general spectral features in our data, and enable us to estimate what instrument exposure reduces ice-to-sensor coupling enough to prevent icequake detection. Last, we use our resonance data to quantitatively measure how narrowband signals that originate from either artificial or glaciogenic sources will reduce the ability of certain waveform detectors (correlators) to capture transient seismic events, even if sensors remain coupled.

58 GEOSCIENCES↗