Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACOUSTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,261 records · Page 70
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Acoustic emission produced during burst tests of filament-wound bottles.

Acoustic emission was recorded during burst tests of filament-wound, composite pressure vessels. Organic and graphite fibers were tested, and two different epoxy resin systems were used: one with a low and another with a relatively high cure temperature. Acoustic emission was studied for the effects of different winding patterns, artificial flaws, winding-induced fiber fraying, different resins, and different fibers. Small effects produced in the vessels by changes in these variables were greatly magnified when they appeared as changes in acoustic emission. They would, in fact, be difficult or impossible to detect by other test means.

Hamstad, M. A.↗
NASA NTRS1973

Acoustic characteristics of a large-scale augmentor wing model at forward speed

The augmentor wing concept is being studied as one means of attaining short takeoff and landing (STOL) performance in turbofan powered aircraft. Because of the stringent noise requirements for STOL operation, the acoustics of the augmentor wing are undergoing extensive research. The results of a wind tunnel investigation of a large-scale swept augmentor model at forward speed are presented. The augmentor was not acoustically treated, although the compressor supplying the high pressure primary air was treated to allow the measurement of only the augmentor noise. Installing the augmentor flap and shroud on the slot primary nozzle caused the acoustic dependence on jet velocity to change from eighth power to sixth power. Deflecting the augmentor at constant power increased the perceived noise level in the forward quadrant. The effect of airspeed was small. A small aft shift in perceived noise directivity was experienced with no significant change in sound power. Sealing the lower augmentor slot at a flap deflection of 70 deg reduced the perceived noise level in the aft quadrant. The seal prevented noise from propagating through the slot.

Falarski, M. D.↗
NASA NTRS1973

Sound propagation in and radiation from acoustically lined flow ducts: A comparison of experiment and theory

The results of an experimental and theoretical study of many of the fundamental details of sound propagation in hard wall and soft wall annular flow ducts are reported. The theory of sound propagation along such ducts and the theory for determining the complex radiation impedance of higher order modes of an annulus are outlined, and methods for generating acoustic duct modes are developed. The results of a detailed measurement program on propagation in rigid wall annular ducts with and without airflow through the duct are presented. Techniques are described for measuring cut-on frequencies, modal phase speed, and radial and annular mode shapes. The effects of flow velocity on cut-on frequencies and phase speed are measured. Comparisons are made with theoretical predictions for all of the effects studies. The two microphone method of impedance is used to measure the effects of flow on acoustic liners. A numerical study of sound propagation in annular ducts with one or both walls acoustically lined is presented.

Plumblee, H. E., Jr.↗
NASA NTRS1974

TF34 Quiet Nacelle nearfield acoustic test results

The results of the nearfield acoustic tests conducted on the TF34 Quiet Nacelle are presented. The high fan noise suppression levels being sought (26 PNdB reduction in aft noise) necessitated the use of an extensive system of special nearfield acoustic instrumentation to properly evaluate the suppression achieved. The design, operation, and test results from each of these nearfield acoustic instrumentation systems are presented.

Coward, W. E.↗
NASA NTRS1974

Development of acoustically lined ejector technology for multitube jet noise suppressor nozzles by model and engine tests over a wide range of jet pressure ratios and temperatures

An experimental program comprising model nozzle and full-scale engine tests was undertaken to acquire parametric data for acoustically lined ejectors applied to primary jet noise suppression. Ejector lining design technology and acoustical scaling of lined ejector configurations were the major objectives. Ground static tests were run with a J-75 turbojet engine fitted with a 37-tube, area ratio 3.3 suppressor nozzle and two lengths of ejector shroud (L/D = 1 and 2). Seven ejector lining configurations were tested over the engine pressure ratio range of 1.40 to 2.40 with corresponding jet velocities between 305 and 610 M/sec. One-fourth scale model nozzles were tested over a pressure ratio range of 1.40 to 4.0 with jet total temperatures between ambient and 1088 K. Scaling of multielement nozzle ejector configurations was also studied using a single element of the nozzle array with identical ejector lengths and lining materials. Acoustic far field and near field data together with nozzle thrust performance and jet aerodynamic flow profiles are presented.

Atvars, J.↗
NASA NTRS1974

Aerodynamic and acoustic performance of ejectors for engine-under-the-wing concepts

Subsonic thrust augmentation, exhaust plume velocity contours and acoustic characteristics of a small-scale, 6-tube mixer nozzle with ejector were obtained with and without a wing. Thrust augmentation up to 30 percent was achieved. Aerodynamic results showed that at a given location, greater downstream velocities are obtained with an ejector than with the baseline nozzle. Ejectors reduce high frequency noise; however, low frequency noise amplification also occurs. Acoustic reflections off the wing increase the noise level to a ground observer. With an ejector, the acoustic benefits of forward velocity may be significantly reduced compared with the baseline nozzle.

Vonglahn, U.↗
NASA NTRS1973

The use of a digital computer for calculation of acoustic fields of complex vibrating structures by the reciprocity principle

A program was compiled for calculating acoustical pressure levels, which might be created by vibrations of complex structures (an assembly of shells and rods), under the influence of a given force, for cases when these fields cannot be measured directly. The acoustical field is determined according to transition frequency and pulse characteristics of the structure in the projection mode. Projection characteristics are equal to the reception characteristics, for vibrating systems in which the reciprocity principle holds true. Characteristics in the receiving mode are calculated on the basis of experimental data on a point pulse space velocity source (input signal) and vibration response of the structure (output signal). The space velocity of a pulse source, set at a point in space r, where it is necessary to calculate the sound field of the structure p(r,t), is determined by measurements of acoustic pressure, created by a point source at a distance R. The vibration response is measured at the point where the forces F and f exciting the system should act.

Rimskiy-Korsakov, A. V.↗
NASA NTRS1974

Advanced acoustic cavity technology

A series of rocket motor firings was performed in a modified linear aerospike thrust chamber with the H2/O2 propellant combination to allow determination of the physical properties of the combustion gases in acoustic cavities located in the chamber side walls. A preliminary analytical study was first conducted to define theoretically both the appropriate cavity dimensions and the combustion gas flow field adjacent to the cavity openings. During the subsequent motor firings, cavity gas temperature profiles were measured and gas samples were withdrawn from the bottom of the cavities for compositional analysis by measurement of pressure/temperature variation and gas chromatography. Data were obtained with both radially and axially oriented cavities and with and without hydrogen bleed flow through the cavities. A simplified procedure was developed for predicting gas cavity and acoustic velocity for use in acoustic cavity design analyses.

Hines, W. S.↗
NASA NTRS1974

Analysis of combustion instability in liquid propellant engines with or without acoustic cavities

Analytical studies have been made of the relative combustion stability of various propellant combinations when used with hardware configurations representative of current design practices and with or without acoustic cavities. Two combustion instability models, a Priem-type model and a modification of the Northern Research and Engineering (NREC) instability model, were used to predict the variation in engine stability with changes in operating conditions, hardware characteristics or propellant combination, exclusive of acoustic cavity effects. The NREC model was developed for turbojet engines but is applicable to liquid propellant engines. A steady-state combustion model was used to predict the needed input for the instability models. In addition, preliminary development was completed on a new model to predict the influence of an acoustic cavity with specific allowance for the effects the nozzle, steady flow and combustion.

Oberg, C. L.↗
NASA NTRS1974

Test of acoustic tone source and propulsion performance of C8A Buffalo suppressor nozzle

Results are presented for a static acoustic and propulsion performance ground test conducted at the Boeing hot nozzle facility on the C8A Buffalo noise suppressor nozzle. Various methods to remove a nozzle-associated 2000-Hz tone are evaluated. Results of testing this rectangular-array lobed nozzle for propulsion performance and acoustic directivity are reported. Recommendations for future nozzle modifications and further testing are included. Appendix A contains the test plan. Appendix B presents the test log. Appendix C contains plots of the one-third octave sound pressure levels recorded during the test. Appendix D describes the acoustic data recording and reduction systems. The performance data is tabulated in Appendix E.

Marrs, C. C.↗
NASA NTRS1974

The application of acoustic emission technique to fatigue crack measurement

The applicability of acoustic emission technique to measure fatigue cracks in aluminum alloy specimens was investigated. There are several variables, such as the metallurgical and the physical treatment of the specimen, that can affect the level of acoustic activity of a fatigue specimen. It is therefore recommended that the acoustic emission technique be supplemented by other nondestructive evaluation methods to obtain quantitative data on crack growth.

Singh, J. J.↗
NASA NTRS1973

The acoustics of aircraft engine-duct systems

Noise generated in aircraft engines is usually suppressed by acoustically treating the engine ducts. The optimization of this treatment requires an understanding of the transmission and attenuation of the acoustic waves. A critical review is presented of the state of the art regarding methods of determining the transmission and attenuation parameters and the effect on these parameters of (1) acoustic properties of liners, (2) the mean velocity, including uniform and shear profiles and nonparallel flow, (3) axial and transverse temperature gradients, (4) slowly and abruptly varying cross sections, and (5) finite-amplitude waves and nonlinear duct liners.

Nayfeh, A. H.↗
NASA NTRS1973

Study of acoustic emission during mechanical tests of large flight weight tank structure

A PPO-insulated, flight-weight, subscale, aluminum tank was monitored for acoustic emissions during a proof test and during 100 cycles of environmental test simulating space flights. The use of a combination of frequency filtering and appropriate spatial filtering to reduce background noise was found to be sufficient to detect acoustic emission signals of relatively small intensity expected from subcritical crack growth in the structure. Several emission source locations were identified, including the one where a flaw was detected by post-test x-ray inspections. For most source locations, however, post-test inspections did not detect flaws; this was partially attributed to the higher sensitivity of the acoustic emission technique than any other currently available NDT method for detecting flaws. For these non-verifiable emission sources, a problem still remains in correctly interpreting observed emission signals.

Mccauley, B. O.↗
NASA NTRS1974

Nonlinear acoustic propagation in rectangular ducts

The method of multiple scales is used to obtain a second-order uniformly valid expansion for nonlinear acoustic wave propagation in a rectangular duct whose walls are treated with a nonlinear acoustic material. The wave propagation in the duct is characterized by the unsteady nonlinear Euler equations. The results show that nonlinear materials attenuate sound more than linear materials except at high acoustic frequencies. The nonlinear materials produce higher and combination tones which have higher attenuation rates than the fundamentals. Moreover, the attenuation rates of the fundamentals increase with increasing amplitude.

Nayfeh, A. H.↗
NASA NTRS1974

A comparison of acoustic and random vibration testing of spacecraft

Before selecting the most suitable testing technique in a particular case, it has to be considered which of the two methods duplicates better the distribution of vibration responses to be expected during the actual launch phase. An investigation is conducted of the case of a large, low density spacecraft launched by a vehicle which produces significant acoustic noise and transmits relatively little vibration through the mechanical path provided by the vehicle structure in the area of the spacecraft interface. Criteria for vibration-acoustic equivalence are discussed along with tests conducted with the Synchronous Meteorological Satellite, the Radio Astronomy Explorer, and the Orbiting Geophysical Spacecraft. The investigation indicates that the vibration test is generally a poor substitute for an acoustic study.-

Bangs, W. F.↗
NASA NTRS1974

Investigation of acoustic radiation from supersonic turbulent jets by double-pulse holographic interferometry

A new experimental method was used to optically investigate the acoustic field radiated from supersonic jets. The method utilizes a pulse ruby laser to obtain double exposure holograms of the sound field of a supersonic jet. The jet remains on during both exposures thus eliminating the no-flow exposure. The time separation between the pulses can be varied depending on the spectral component of the radiation to be observed. Optical records were obtained for supersonic jets with exit Mach number 1.0, 1.5 and 2.0. It was found that high frequency acoustic radiation mainly originates from the regions near the nozzle exit, whereas the low frequency noise is generated from regions further downstream. These findings are consistent with the acoustic data obtained by other investigators.

Ozkul, A.↗
NASA NTRS1974

Evaluation of acoustic emission technique for crack growth measurement in aeronautical structures

An investigation has been conducted concerning the possibility to use the acoustic emission technique for the measurement of fatigue crack growth in aluminum alloy specimens. Two types of aluminum alloys were tested in the investigation. It was found that the acoustic emission technique provides a reliable indication of changes in the crack dimensions over relatively short periods of time. The level of acoustic activity serves as an indicator of the size of the cracks.

Singh, J. J.↗
NASA NTRS1974

Aerodynamic and acoustic performance of ejectors for engine-under-the-wing concepts

Subsonic thrust augmentation, exhaust plume velocity contours and acoustic characteristics of a small-scale, 6-tube mixer nozzle with ejector were obtained with and without a wing. Thrust augmentation up to 30 percent was achieved. Aerodynamic results showed that at a given location, greater downstream velocities are obtained with an ejector than with the baseline nozzle. Ejectors reduce high frequency noise; however, low-frequency noise amplification also occurs. Acoustic reflections off the wing increase the noise level to a ground observer. With an ejector, the acoustic benefits of forward velocity may be significantly reduced compared with the baseline nozzle.

Von Glahn, U.↗