Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “weight coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Modern rotor balancing - Emerging technologies

Modern balancing methods for flexible and rigid rotors are explored. Rigid rotor balancing is performed at several hundred rpm, well below the first bending mode of the shaft. High speed balancing is necessary when the nominal rotational speed is higher than the first bending mode. Both methods introduce weights which will produce rotor responses at given speeds that will be exactly out of phase with the responses of an unbalanced rotor. Modal balancing seeks to add weights which will leave other rotor modes unaffected. Also, influence coefficients can be determined by trial and error addition of weights and recording of their effects on vibration at speeds of interest. The latter method is useful for balancing rotors at other than critical speeds and for performing unified balancing beginning with the first critical speed. Finally, low-speed flexible balancing permits low-speed tests and adjustments of rotor assemblies which will not be accessible when operating in their high-speed functional configuration. The method was developed for the high pressure liquid oxygen turbopumps for the Shuttle.

Zorzi, E. S.↗
NASA NTRS1986

Theory of beat-resonant coupling of electrostatic modes

A general expression is derived for the beat-resonant coupling electrostatic modes in a Vlasov plasma. The result for the coupling of two modes has a simple structure: the appropriate momentum gradient of the equilibrium particle distribution is weighted by a positive coupling coefficient and averaged over the resonance surface in momentum space. The contributions of all the resonance surfaces are then summed. This basic structure had been previously exhibited only for specific homogeneous plasma models. The present theory, which unifies and greatly simplifies these individual treatments, is based on a variational formulation of the Vlasov-Poisson equations. Using Lie transforms, the variational principle is reexpressed in oscillation-center variables, and then the nonlinear wave dynamics are obtained from the independent variations of the wave phase and the wave amplitude. The power of the method is then applied to a strongly magnetized, strongly inhomogeneous, non-neutral plasma model.

Crawford, John David↗
NASA NTRS1993

The Blue Emu

The primary goal in designing the Blue Emu was to provide an airline with a cost efficient and profitable means of transporting passengers between the major cities in Aeroworld. The design attacks the market where a demand for inexpensive transportation exists and for this reason the Blue Emu is an attractive investment for any airline. In order to provide a profitable aircraft, special attention was paid to cost and economics. For example, in manufacturing, simplicity was stressed in structural design to reduce construction time and cost. Aerodynamic design employed a tapered wing which reduced the induced drag coefficient while also reducing the weight of the wing. Even the propulsion system was selected with cost effectiveness in mind, yet also to maintain the marketability of the aircraft. Thus, in every aspect of the design, consideration was given to economics and marketability of the final product.

Descalzi, Doug↗
NASA NTRS1999

Experimentally Determined Crack Location and Mixed Mode Stress Intensity Factors

This presentation first examines five strain field equations: the two modes of the Westergaard equations, and a mixed mode; the generalized coordinate system, and the significance testing of coefficients. It also discusses the weighted multiple linear least squares method, which shows why it is difficult to find the crack tip. The presentation then discusses the experiments to examine stress intensity. Lastly, comparison of finite element method results and experimental results is reviewed.

Zachary, Loren W.↗
NASA NTRS2001

Effective Thermal Conductivity of High Porosity Open Cell Nickel Foam

The effective thermal conductivity of high-porosity open cell nickel foam samples was measured over a wide range of temperatures and pressures using a standard steady-state technique. The samples, measuring 23.8 mm, 18.7 mm, and 13.6 mm in thickness, were constructed with layers of 1.7 mm thick foam with a porosity of 0.968. Tests were conducted with the specimens subjected to temperature differences of 100 to 1000 K across the thickness and at environmental pressures of 10(exp -4) to 750 mm Hg. All test were conducted in a gaseous nitrogen environment. A one-dimensional finite volume numerical model was developed to model combined radiation/conduction heat transfer in the foam. The radiation heat transfer was modeled using the two-flux approximation. Solid and gas conduction were modeled using standard techniques for high porosity media. A parameter estimation technique was used in conjunction with the measured and predicted thermal conductivities at pressures of 10(exp -4) and 750 mm Hg to determine the extinction coefficient, albedo of scattering, and weighting factors for modeling the conduction thermal conductivity. The measured and predicted conductivities over the intermediate pressure values differed by 13%.

Sullins, Alan D.↗
NASA NTRS2013

FUN3D Airload Predictions for the Full-Scale UH-60A Airloads Rotor in a Wind Tunnel

An unsteady Reynolds-Averaged Navier-Stokes solver for unstructured grids, FUN3D, is used to compute the rotor performance and airloads of the UH-60A Airloads Rotor in the National Full-Scale Aerodynamic Complex (NFAC) 40- by 80-foot Wind Tunnel. The flow solver is loosely coupled to a rotorcraft comprehensive code, CAMRAD-II, to account for trim and aeroelastic deflections. Computations are made for the 1-g level flight speed-sweep test conditions with the airloads rotor installed on the NFAC Large Rotor Test Apparatus (LRTA) and in the 40- by 80-ft wind tunnel to determine the influence of the test stand and wind-tunnel walls on the rotor performance and airloads. Detailed comparisons are made between the results of the CFD/CSD simulations and the wind tunnel measurements. The computed trends in solidity-weighted propulsive force and power coefficient match the experimental trends over the range of advance ratios and are comparable to previously published results. Rotor performance and sectional airloads show little sensitivity to the modeling of the wind-tunnel walls, which indicates that the rotor shaft-angle correction adequately compensates for the wall influence up to an advance ratio of 0.37. Sensitivity of the rotor performance and sectional airloads to the modeling of the rotor with the LRTA body/hub increases with advance ratio. The inclusion of the LRTA in the simulation slightly improves the comparison of rotor propulsive force between the computation and wind tunnel data but does not resolve the difference in the rotor power predictions at mu = 0.37. Despite a more precise knowledge of the rotor trim loads and flight condition, the level of comparison between the computed and measured sectional airloads/pressures at an advance ratio of 0.37 is comparable to the results previously published for the high-speed flight test condition.

Lee-Rausch, Elizabeth M.↗
NASA NTRSDate not supplied

Flow Boiling and Condensation Experiment (FBCE): From Initial Concept to Full Implementation on the International Space Station

Two phase thermal management systems that capitalize on both latent and sensible heats of the working fluid can yield orders of magnitude enhancements in flow boiling and condensation heat transfer coefficients and reduce size and weight of future space systems. Because the understanding of microgravity influences on two-phase flow and heat transfer is quite limited, there is presently an urgent need for a new experimental microgravity facility to enable investigators to perform long-duration flow boiling and condensation experiments in pursuit of reliable databases. This presentation will discuss evolution of the Flow Boiling and Condensation Experiment (FBCE), a collaborative effort between Purdue University and NASA Glenn Research Center, from initial concept with clearly defined objectives to full implementation on the International Space Station (ISS). It will be shown how this facility will serve as a primary platform for obtaining two-phase flow and heat transfer data in microgravity. By comparing the microgravity data against those obtained in Earth gravity, it will be possible to ascertain the influence of body force on two-phase transport phenomena in pursuit of mechanistic models as well as correlations, and to help determine the minimum flow criteria to ensure gravity independent flow boiling and condensation.

Flow boiling↗
NASA NTRS1973

Mars gravity derived from long-period motion of Mariner 9

The spherical harmonic coefficients in the gravity field of Mars are determined using a two stage filtering process. In the first stage, a weighted least squares orbit determination processor is applied to Mariner 9 Doppler tracking data to estimate Kepler elements and rates. In the second stage, the Kepler element rates are used as input to another weighted least squares processor that estimates gravity coefficients using the Lagrange perturbation equations. The novelty in this method is the fitting of element rates rather than the elements themselves. This procedure decouples the results from the effects of internal spacecraft dynamics.

Ferrari, A. J.↗
NASA NTRS1961

Take-off Distances of a Supersonic Transport Configuration as Affected by Airplane Rotation During the Take-off Run

The take-off distances over a 35-foot obstacle have been determined for a supersonic transport configuration characterized by a low maximum lift coefficient at a high angle of attack and by high drag due to lift. These distances were determined analytically by means of an electronic digital computer. The effects of rotation speed, rotation angle, and rotation time were determined. A few configuration changes were made to determine the effects of thrust-weight ratio, wing loading, maximum lift coefficient, and induced drag on the take-off distance. The required runway lengths based on Special Civil Air Regulation No. SR-422B were determined for various values of rotation speed and compared with those based on full engine power. Increasing or decreasing the rotation speed as much as 5 knots from the value at which the minimum take-off distance occurred increased the distance only slightly more than 1 percent for the configuration studied. Under-rotation by 1 deg to 1.5 deg increased the take-off distance by 9 to 15 percent. Increasing the time required for rotation from 3 to 5 seconds had a rather small effect on the take-off distance when the values of rotation speed were near the values which result in the shortest take-off distance. When the runway length is based on full engine power rather than on SR-422B, the rotation speed which results in the shortest required runway length is 10 knots lower and the runway length is 4.3 percent less.

Hall, Albert W.↗
NASA NTRS2005

Nondestructive Evaluation of Advanced Materials with X-ray Phase Mapping

X-ray radiation has been widely used for imaging applications since Rontgen first discovered X-rays over a century ago. Its large penetration depth makes it ideal for the nondestructive visualization of the internal structure and/or defects of materials unobtainable otherwise. Currently used nondestructive evaluation (NDE) tools, X-ray radiography and tomography, are absorption-based, and work well in heavy-element materials where density or composition variations due to internal structure or defects are high enough to produce appreciable absorption contrast. However, in many cases where materials are light-weight and/or composites that have similar mass absorption coefficients, the conventional absorption-based X-ray methods for NDE become less useful. Indeed, the light-weight and ultra-high-strength requirements for the most advanced materials used or developed for current flight mission and future space exploration pose a great challenge to the standard NDE tools in that the absorption contrast arising from the internal structure of these materials is often too weak to be resolved. In this presentation, a solution to the problem, the use of phase information of X-rays for phase contrast X-ray imaging, will be discussed, along with a comparison between the absorption-based and phase-contrast imaging methods. Latest results on phase contrast X-ray imaging of lightweight Space Shuttle foam in 2D and 3D will be presented, demonstrating new opportunities to solve the challenging issues encountered in advanced materials development and processing.

Hu, Zhengwei↗
NASA NTRS1991

Trim angle measurements in free-flight facilities

The aerodynamic cofficients and trim angle for an aerobrake at Mach 9.2 and 11.8 were found using a combination of experiment and computation. Free-flight tests were performed at NASA Ames Research Center's Hypervelocity Free-Flight Aerodynamic Facility, and the forebody pressure distribution was calculated using a three-dimensional Navier-Stokes code with an effective specific heat ratio. Using the computed drag, lift, and moments to prescribe the number of terms in the aerodynamic coefficient expansions and to specify the values of the higher order terms, the experimental aerodynamic coefficients and trim angle were found using a six-degree-of-freedom, weighted, least-squares analysis. The experimental and computed aerodynamic coefficients and trim angles are in good agreement. The trim angle obtained from the free-flight tests, 14.7 deg, differs from the design trim angle, 17 deg, and from the Langley wind tunnel results, 12 deg in air and 17 deg in CF4. These differences are attributable to real-gas effects.

Yates, Leslie A.↗
NASA NTRS1990

Optimal model reduction and frequency-weighted extension

In this paper the quadratically optimal model reduction problem for single-input, single-output systems is considered. The reduced order model is determined by minimizing the integral of the magnitude-squared of the transfer function error. It is shown that the numerator coefficients of the optimal approximant satisfy a weighted least squares problem and, on this basis, a two-step iterative algorithm is developed combining a least squares solver with a gradient minimizer. The existence of globally optimal stable solutions to the optimization problem is established, and convergence of the algorithm to stationary values of the cost function is proved. The formulation is extended to handle the frequency-weighted optimal model reduction problem. Three examples demonstrate the optimization algorithm.

Spanos, J. T.↗
NASA NTRS1972

The formation and analysis of a 5 deg equal area block terrestrial gravity field

A set of 23,355 1 degree x 1 degree mean free air anomalies were used to predict a set of 5 degree equal area anomalies and their standard errors. Using the 1 degree data incorporating geophysically predicted values of ACIC, 1283 5 degree blocks were computed. Excluding the geophysically predicted anomalies 1249 blocks were computed. The 1 degree data were also used to compute covariance functions and the equatorial gravity and flattening implied by this data. The predicted anomalies were supplemented by model anomalies to form a complete 1654 global anomaly field. These data were used in a weighted least squares to determine potential coefficients to degree 15, and in a summation type formulation to determine potential coefficients to degree 25. These potential coefficients sets are compared to recent satellite determinations.

Rapp, R. H.↗
NASA NTRS1978

Short arc reduction of radar altimetry computer program

The Air Force Geophysics Laboratory computer program SARRA (Short Arc Reduction of Radar Altimetry) has been used for geoid determination with altimetric observations from the GEOS-3 satellite. An important feature of SARRA is the simultaneous recovery of the orbit parameters and the surface coefficients as defined by covariance function weights. Orbits good to approximately 20 meters are adequate for precise geoid determinations by virtue of the orbital adjustment in the reductions. Altimetric data over a portion of the North Atlantic Ocean have been processed to derive the regional geoid and gravity field. Analyses of altimeter residuals resulting from the short arc adjustment show that the residuals can be used to define the neglected higher order geoidal undulations with high fidelity and continuity.

Hadgigeorge, G.↗
NASA NTRS1980

Balancing of a power-transmission shaft with the application of axial torque

Evaluation of power transmission shafting for high-speed balancing has shown that when axial torque is applied, the imbalance response is altered. An increase in synchronous excitation always occurs if the axial torque level is altered from the value used during balancing; this was the case even when the shaft was balanced with torque applied. The twisting of the long slender shaft produces a change in the imbalance distribution sufficient to disrupt the balanced state. This paper presents a review of the analytic development of a weighted least squares approach to influence coefficient balancing and a review of experimental results. The analytic approach takes advantage of the fact that the past testing has shown that the influence coefficients are not significantly affected by the application of axial torque. The 3.60-m (12-ft) long aluminum shaft, 7.62 cm (3 in.) in diameter was run through the first flexural critical speed at torque levels ranging from zero-torque to 903.8 N-M (8000 lb-in.) in 112.9 N-M (1000 lb-in.) increments. Good comparison was achieved between predicted and experimental results.

Zorzi, E. S.↗
NASA NTRS1982

Aerodynamic levitation of laser-heated solids in gas jets

The aerodynamic levitation technique is developed for studies of high-temperature material properties and gas/condensed-phase reaction kinetics. Stable levitation is demonstrated in a supersonic jet from a 0.081 cm nozzle with 0.03-0.20 g 0.24-0.47 cm diameter solid spheres at a height between 0.7-2.0 cm above the nozzle and ambient pressures between 1.1-18 Torr. A model of supersonic jet levitation is developed which accurately predicts the values of height vs pressure over the full range of conditions investigated. It is found that the efficiency with which jet momentum is converted into levitation force decreases with the jet/specimen diameter ratio and the jet Reynolds number, and the rate of jet spreading with distance from the nozzle is found to agree with that measured by pitot tube traverses of the jet. In addition, laser heating is shown to reduce the jet momentum required for levitation at a given height and to increase levitation stability. Measurements of sphere levitation in subsonic gas jets show that the required jet momentum flow rate exceeds the specimen weight by about 2/the specimen drag coefficient at its terminal free-fall speed under ambient conditions.

Nordine, P. C.↗
NASA NTRS1985

Method of and apparatus for generating an interstitial point in a data stream having an even number of data points

Apparatus for doubling the data density rate of an analog to digital converter or doubling the data density storage capacity of a memory deviced is discussed. An interstitial data point midway between adjacent data points in a data stream having an even number of equal interval data points is generated by applying a set of predetermined one-dimensional convolute integer coefficients which can include a set of multiplier coefficients and a normalizer coefficient. Interpolator means apply the coefficients to the data points by weighting equally on each side of the center of the even number of equal interval data points to obtain an interstital point value at the center of the data points. A one-dimensional output data set, which is twice as dense as a one-dimensional equal interval input data set, can be generated where the output data set includes interstitial points interdigitated between adjacent data points in the input data set. The method for generating the set of interstital points is a weighted, nearest-neighbor, non-recursive, moving, smoothing averaging technique, equivalent to applying a polynomial regression calculation to the data set.

Edwards, T. R.↗