Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “water model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Derivation of a three dimensional numerical water quality model for estuary and continental shelf application

A derivation is given for a three dimensional mass transport equation which is appropriate for numerical modeling of estuary and continental shelf water quality variations for both the time dependent and steady state cases. A finite difference approximation to the derived equation is presented and a solution scheme for the resulting equations outlined. Preliminary results are obtained using the model for the extremely simple problems which have analytical solutions. The numerical model, as presented, will provide a scheme to study water quality problems in coastal waters for both steady state and time dependent cases.

Spaulding, M.↗
NASA NTRS1994

Impact of microwave derived soil moisture on hydrologic simulations using a spatially distributed water balance model

Spatial distributions of soil moisture over an agricultural watershed with a drainage area of 60 ha were derived from two NASA microwave remote sensors, and then used as a feedback to determine the initial condition for a distributed water balance model. Simulated hydrologic fluxes over a period of twelve days were compared with field observations and with model predictions based on a streamflow derived initial condition. The results indicated that even the low resolution remotely sensed data can improve the hydrologic model's performance in simulating the dynamics of unsaturated zone soil moisture. For the particular watershed under study, the simulated water budget was not sensitive to the resolutions of the microwave sensors.

Lin, D. S.↗
DOE OSTI2023

A Decision-Relevant Factor-Fixing Framework: Application to Uncertainty Analysis of a High-Dimensional Water Quality Model

Factor Fixing (FF) is a common method for reducing the number of model parameters to lower computational cost. FF typically starts with distinguishing the insensitive parameters from the sensitive and pursues uncertainty quantification (UQ) on the resulting reduced-order model, fixing each insensitive parameter at a fixed value. There is a need, however, to expand such a common approach to consider the effects of decision choices in the FF-UQ procedure on metrics of interest. Therefore, to guide the use of FF and increase confidence in the resulting dimension-reduced model, we propose a new adaptive framework consisting of four principles: (a) re-parameterize the model first to reduce obvious non-identifiable parameter combinations, (b) focus on decision relevance especially with respect to errors in quantities of interest (QoI), (c) conduct adaptive evaluation and robustness assessment of errors in the QoI across FF choices as sample size increases, and (d) reconsider whether fixing is warranted. The framework is demonstrated on a spatially-distributed water quality model. The error in estimates of QoI caused by FF can be estimated using a Polynomial Chaos Expansion (PCE) surrogate model. Built with 70 model runs, the surrogate is computationally inexpensive to evaluate and can provide global sensitivity indices for free. For the selected catchment, just two factors may provide an acceptably accurate estimate of model uncertainty in the average annual load of Total Suspended Solids (TSS), suggesting that reducing the uncertainty in these two parameters is a priority for future work before undertaking further formal uncertainty quantification.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1975

Development of a three dimensional numerical water quality model for continental shelf applications

A model to predict the distribution of water quality parameters in three dimensions was developed. The mass transport equation was solved using a non-dimensional vertical axis and an alternating-direction-implicit finite difference technique. The reaction kinetics of the constituents were incorporated into a matrix method which permits computation of the interactions of multiple constituents. Methods for the computation of dispersion coefficients and coliform bacteria decay rates were determined. Numerical investigations of dispersive and dissipative effects showed that the three-dimensional model performs as predicted by analysis of simpler cases. The model was then applied to a two dimensional vertically averaged tidal dynamics model for the Providence River. It was also extended to a steady state application by replacing the time step with an iteration sequence. This modification was verified by comparison to analytical solutions and applied to a river confluence situation.

Spaulding, M.↗
DOE OSTI2025

Enhancing Drinking Water Quality Modeling: Leveraging Physics Informed Neural Networks for Learning with Imperfect Reaction Models and Partial Data

Chemical kinetics models, typically formulated as systems of ordinary or partial differential equations, are valuable tools for simulating drinking water quality. However, these models often face inaccuracies due to discrepancies between the laboratory and the real-world conditions, as well as limitations in experimental analytical methods, hindering the accurate representation of the true underlying chemical mechanisms. In this study, we propose a Physics Informed Neural Network (PINN), using the eXtreme Theory of Functional Connections, to improve the prediction of chemical concentrations over time. The PINN method accounts for imperfect chemical models and incorporates partial data to improve predictions. Focusing on reactions describing water disinfection residual and disinfectant byproduct formation, which are crucial for public health and regulatory compliance, we demonstrate that the PINN model is able to accurately predict the concentrations of chemical species across various pH values. Notably, the model extends its accuracy to predict concentrations of chemical species not originally included in its training data. The developed method can be extended to a variety of chemical systems, offering a wide array of potential applications.

13 HYDRO ENERGY↗
DOE OSTI2022

Spatial heterogeneity effects on land surface modeling of water and energy partitioning

Abstract. Understanding the influence of land surface heterogeneity on surface water and energy fluxes is crucial for modeling earth system variability and change. This study investigates the effects of four dominant heterogeneity sources on land surface modeling, including atmospheric forcing (ATM), soil properties (SOIL), land use and land cover (LULC), and topography (TOPO). Our analysis focused on their impacts on the partitioning of precipitation (P) into evapotranspiration (ET) and runoff (R), partitioning of net radiation into sensible heat and latent heat, and corresponding water and energy fluxes. An initial set of 16 experiments were performed over the continental US (CONUS) using the E3SM land model (ELMv1) with different combinations of heterogeneous and homogeneous datasets. The Sobol' total and first-order sensitivity indices were utilized to quantify the relative importance of the four heterogeneity sources. Sobol' total sensitivity index measures the total heterogeneity effects induced by a given heterogeneity source, consisting of the contribution from its own heterogeneity (i.e., the first-order index) and its interactions with other heterogeneity sources. ATM and LULC are the most dominant heterogeneity sources in determining spatial variability of water and energy partitioning, mainly contributed by their own heterogeneity and slightly contributed by their interactions with other heterogeneity sources. Their heterogeneity effects are complementary, both spatially and temporally. The overall impacts of SOIL and TOPO are negligible, except TOPO dominates the spatial variability of R/P across the transitional climate zone between the arid western and humid eastern CONUS. Accounting for more heterogeneity sources improves the simulated spatial variability of water and energy fluxes when compared with ERA5-Land reanalysis dataset. An additional set of 13 experiments identified the most critical components within each heterogeneity source, which are precipitation, temperature, and longwave radiation for ATM, soil texture, and soil color for SOIL and maximum fractional saturated area parameter for TOPO.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

H2OI95: A Stand-Alone Fortran Code for Evaluating the IAPWS-95 Equation-of-State Model for Water (Rev. 1)

H2OI95 is a stand-alone Fortran code for evaluating the IAPWS-95 equation-of-state model for the thermodynamic properties of water. It also evaluates the corresponding thermochemical properties of water consistent with the CODATA recommendations. The IAPWS-95 model is based on a model equation for the dimensionless Helmholtz energy for which the primary variables are the inverse reduced temperature (τ = T cr /T ) and reduced density (δ = ρ/ρ cr ). Here T is the absolute temperature (K), ρ is density (kg/m³), and the subscript “ cr ” refers to the critical point of water (647.096 K and 22.064 MPa pressure in this model, for which ρ cr is 322 kg/m³). The code solves four basic types of problems, distinguished by the specified inputs: 1. Temperature (K) and density (ρ kg/m³) or reduced density (δ) 2. Temperature (K) and pressure (MPa). 3. Temperature (K) on the saturation (liquid-vapor equilibrium) curve 4. Pressure (MPa) on the saturation curve. Each type of problem is run using a corresponding input (text) file. All but the first type of problem require iteration. For example, to solve for desired temperature and pressure, the reduced density must be adjusted to give the desired pressure. Iteration is accomplished using the Newton-Raphson method, though the secant method is also used in solving the fourth type of problem. For the last three types of problems, H2OI95 has been used to conduct numerical studies of convergence and the problem of multiple numerical solutions, some of which are not physically valid. Obtaining valid results depends mainly on appropriate choice of starting values for the density. The default values used in H2OI95 appear to consistently lead to generally desired results. With modification (not addressed here), H2OI95 can be used to support SUPCRT92 and similar codes that compute chemical thermodynamic properties of species and reactions over a wide range of temperature and pressure (273.16-1273K and 0-1000 MPa). Version 1.1 of this software calculates an extended set of water properties, including some derivable solely from IAPWS-95, such as the isobaric thermal expansivity and the isothermal compressibility, and still other properties based on supplementary models sanctioned by IAPWS, including the dynamic viscosity, thermal conductivity, surface tension, and static dielectric constant, and various other properties (notably Debye-Hückel parameters) derivable from the dielectric constant and its partial derivatives with respect to temperature and pressure. A coding error in Version 1.0 was identified while testing the implementation of the viscosity model. This error is described in Appendix C. It mainly affects calculation of “higher order” properties such as compressibility and heat capacity near the critical point.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2013

Multiphase Modeling of Water Injection on Flame Deflector

This paper describes the use of an Eulerian Dispersed Phase (EDP) model to simulate the water injected from the flame deflector and its interaction with supersonic rocket exhaust from a proposed Space Launch System (SLS) vehicle. The Eulerian formulation, as part of the multi-phase framework, is described. The simulations show that water cooling is only effective over the region under the liquid engines. Likewise, the water injection provides only minor effects over the surface area under the solid engines.

Vu, Bruce T.↗
NASA NTRS2010

NASA-Modified Precipitation Products to Improve EPA Nonpoint Source Water Quality Modeling for the Chesapeake Bay

The Environmental Protection Agency (EPA) has estimated that over 20,000 water bodies within the United States do not meet water quality standards. Ninety percent of the impairments are typically caused by nonpoint sources. One of the regulations in the Clean Water Act of 1972 requires States to monitor the Total Maximum Daily Load (TMDL), or the amount of pollution that can be carried by a water body before it is determined to be "polluted", for any watershed in the U.S.. In response to this mandate, the EPA developed Better Assessment Science Integrating Nonpoint Sources (BASINS) as a Decision Support Tool (DST) for assessing pollution and to guide the decision making process for improving water quality. One of the models in BASINS, the Hydrological Simulation Program -- Fortran (HSPF), computes daily stream flow rates and pollutant concentration at each basin outlet. By design, precipitation and other meteorological data from weather stations serve as standard model input. In practice, these stations may be unable to capture the spatial heterogeneity of precipitation events especially if they are few and far between. An attempt was made to resolve this issue by substituting station data with NASA modified/NOAA precipitation data. Using these data within HSPF, stream flow was calculated for seven watersheds in the Chesapeake Bay Basin during low flow periods, convective storm periods, and annual flows. In almost every case, the modeling performance of HSPF increased when using the NASA-modified precipitation data, resulting in better stream flow statistics and, ultimately, in improved water quality assessment.

Nigro, Joseph↗
NASA NTRS1981

Water production models for comet Bradfield /1979 X/

Whipple (1950, 1951) has proposed that water might be the dominant volatile constituent of the cometary nucleus. The considered investigation is concerned with the clues which observations of the cometary coma provide regarding the parents of the dominant observed coma species. In the early part of 1980, comet Bradfield (1979 X) was observed with the aid of the International Ultraviolet Explorer (IUE). These measurements are the first which provide a basis for a comprehensive study of all three water dissociation products, H, O, and OH, simultaneously. The IUE observations of comet Bradfield are compared with the predictions derived from an H2O model. The obtained results indicate that the observed brightnesses of H, O, and OH are certainly consistent with a common water source for all three species.

Weaver, H. A.↗
NASA NTRS2013

Inferring Soil Moisture Memory from Streamflow Observations Using a Simple Water Balance Model

Soil moisture is known for its integrative behavior and resulting memory characteristics. Soil moisture anomalies can persist for weeks or even months into the future, making initial soil moisture a potentially important contributor to skill in weather forecasting. A major difficulty when investigating soil moisture and its memory using observations is the sparse availability of long-term measurements and their limited spatial representativeness. In contrast, there is an abundance of long-term streamflow measurements for catchments of various sizes across the world. We investigate in this study whether such streamflow measurements can be used to infer and characterize soil moisture memory in respective catchments. Our approach uses a simple water balance model in which evapotranspiration and runoff ratios are expressed as simple functions of soil moisture; optimized functions for the model are determined using streamflow observations, and the optimized model in turn provides information on soil moisture memory on the catchment scale. The validity of the approach is demonstrated with data from three heavily monitored catchments. The approach is then applied to streamflow data in several small catchments across Switzerland to obtain a spatially distributed description of soil moisture memory and to show how memory varies, for example, with altitude and topography.

Soil Moisture↗
NASA NTRS1993

Variational data assimilation with a semi-Lagrangian semi-implicit global shallow-water equation model and its adjoint

An adjoint model is developed for variational data assimilation using the 2D semi-Lagrangian semi-implicit (SLSI) shallow-water equation global model of Bates et al. with special attention being paid to the linearization of the interpolation routines. It is demonstrated that with larger time steps the limit of the validity of the tangent linear model will be curtailed due to the interpolations, especially in regions where sharp gradients in the interpolated variables coupled with strong advective wind occur, a synoptic situation common in the high latitudes. This effect is particularly evident near the pole in the Northern Hemisphere during the winter season. Variational data assimilation experiments of 'identical twin' type with observations available only at the end of the assimilation period perform well with this adjoint model. It is confirmed that the computational efficiency of the semi-Lagrangian scheme is preserved during the minimization process, related to the variational data assimilation procedure.

Li, Y.↗
DOE OSTI2021

Hydrological analysis in watersheds with a variable-resolution global climate model (VR-CESM)

Traditionally, watershed-scale hydrology is simulated by distributed hydrological models with offline meteorological forcing data, or by regional regional climate models that link atmospheric and land hydrology interactions. Global climate models (GCMs) are rarely used to study watershed-scale hydrology due to the relatively coarse grid resolution, computationally expensive downscaling, and simplified physical processes. Recently, however, watershed-scale hydrology analysis has become possible in GCMs due to the development of variable-resolution GCMs that dynamically couple the hydrological processes between atmosphere and land systems at fine resolutions in selected regions and coarse resolution elsewhere. In this study, we used the variable-resolution Community Earth System Model (VR-CESM) with refined-resolution (14 km) in the western U.S. and eastern China to evaluate watershed-scale hydrology. Furthermore, we compared the historical VR-CESM outputs with gauge measurements and other hydrological models (e.g., National Water Model in the U.S.) and calibrated the subsurface runoff capacities in four mountainous watersheds. An RCP8.5 projection from 2007 to 2050 is used to estimate the impact of changing precipitation and snow climatology on watershed hydrology. We also analyzed the long-term runoff variability and the possibility of extreme runoff events as simulated by the VR-CESM. Although calibration is not possible in larger-scale watersheds, VR-CESM simulates the long-term annual variability of watersheds and provides insights on climate change impacts on hydrology. We conclude that refined-resolution VR-CESM can be used for watershed-scale hydrology analysis to understand water resources and water balance, in addition to traditional watershed-scale hydrological models. It enables hydrological analysis at multiple watersheds in one simulation and can help understand the two-way dynamics between land surface hydrology and atmospheric processes, and is especially practical for projecting climate change impacts. However, it is challenging to apply VR-CESM for hydrologic analysis in regulated watersheds as human factors (e.g., pumping, irrigation, water diversion) have not been fully addressed in VR-CESM.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Utilizing waste heat in wastewater treatment plants for water desalination: Modeling and Multi-Objective optimization of a Multi-Effect desalination system using Decision Tree Regression and Pelican optimization algorithm

This paper examines the feasibility of using waste heat from wastewater treatment plants (WWTPs) for water desalination. A model was developed to utilize waste heat from the gensets at As Samra WWTP in Jordan, using real data and TRNSYS® software to calculate available waste heat. The desalination process was then modeled with ASPEN PLUS® software, focusing on multi-effect desalination (MED). Both series and parallel configurations for the MED system were compared. The study investigated the effects of system feeding flow rate, feeding pressure, and heat input on productivity, performance ratio, and recovery ratio. The study also introduces a novel optimization technique combining machine learning and modern optimization algorithms to maximize system productivity and performance. Initially, a decision tree regression (DTR) model is developed to establish relationships between key independent variables (flow rate, feed pressure, and heat input) and dependent variables (productivity, performance ratio, and recovery ratio). The Pelican Optimization Algorithm (POA) is then used to identify the optimal values of the independent variables for maximum productivity and performance. The results show that using a series configuration yields a system productivity of 3984.2 kg/hr, a performance ratio of 3.78, and a recovery ratio of 0.991 at a feed flow rate of 4000 kg/hr, feed pressure of 3 bars, and heat input of 719 kW. Optimal productivity (4421 kg/hr), performance ratio (3.81), and recovery ratio (0.851) are achieved at a feed flow rate of 5166 kg/hr, feed pressure of 3.2 bars, and heat input of 794 kW. In conclusion, the techno-economic assessment indicates a levelized cost of water of 1.63 USD/m 3 for parallel configurations and 1.65 USD/m 3 for series configurations, with a payback period of less than two years.

42 ENGINEERING↗
NASA NTRS1999

Physically-Derived Dynamical Cores in Atmospheric General Circulation Models

The algorithm chosen to represent the advection in atmospheric models is often used as the primary attribute to classify the model. Meteorological models are generally classified as spectral or grid point, with the term grid point implying discretization using finite differences. These traditional approaches have a number of shortcomings that render them non-physical. That is, they provide approximate solutions to the conservation equations that do not obey the fundamental laws of physics. The most commonly discussed shortcomings are overshoots and undershoots which manifest themselves most overtly in the constituent continuity equation. For this reason many climate models have special algorithms to model water vapor advection. This talk focuses on the development of an atmospheric general circulation model which uses a consistent physically-based advection algorithm in all aspects of the model formulation. The shallow-water model is generalized to three dimensions and combined with the physics parameterizations of NCAR's Community Climate Model. The scientific motivation for the development is to increase the integrity of the underlying fluid dynamics so that the physics terms can be more effectively isolated, examined, and improved. The expected benefits of the new model are discussed and results from the initial integrations will be presented.

Rood, Richard B.↗
NASA NTRS1999

Physically-Derived Dynamical Cores in Atmospheric General Circulation Models

The algorithm chosen to represent the advection in atmospheric models is often used as the primary attribute to classify the model. Meteorological models are generally classified as spectral or grid point, with the term grid point implying discretization using finite differences. These traditional approaches have a number of shortcomings that render them non-physical. That is, they provide approximate solutions to the conservation equations that do not obey the fundamental laws of physics. The most commonly discussed shortcomings are overshoots and undershoots which manifest themselves most overtly in the constituent continuity equation. For this reason many climate models have special algorithms to model water vapor advection. This talk focuses on the development of an atmospheric general circulation model which uses a consistent physically-based advection algorithm in all aspects of the model formulation. The shallow-water model of Lin and Rood (QJRMS, 1997) is generalized to three dimensions and combined with the physics parameterizations of NCAR's Community Climate Model. The scientific motivation for the development is to increase the integrity of the underlying fluid dynamics so that the physics terms can be more effectively isolated, examined, and improved. The expected benefits of the new model are discussed and results from the initial integrations will be presented.

Rood, Richard B.↗