Results for “treatment” — Page 7

DOE OSTI2022

Effects of surface treatments on ABS mechanical properties from fused filament fabrication

This paper examines the influence of surface treatments on the mechanical properties of acrylonitrile butadiene styrene (ABS) samples printed by fused filament fabrication (FFF). Prior efforts have applied brushing, painting, solvent dipping, infiltration, and vapor smoothing as post-processing surface treatments to improve the mechanical properties of FFF components. Additionally, because FFF can produce components with undesirable surface roughness, mechanical abrasion, epoxy coating, and acetone treatment may increase tensile strength by decreasing stress concentrations. Ridged surface texture may provide desirable tribological or handling properties. Based on these opportunities, this paper investigates abrasive media blasting, epoxy coating, acetone immersion, and ridged texturing surface treatments on the tensile strength and other mechanical properties of FFF ABS samples. ASTM D638-14 Type-I samples were printed, treated on all sample sides, and tested. From tensile tests, the elastic modulus, tensile strength, and fracture strain for both the untreated and treated ABS samples were calculated. For each sample, the surface finish and fracture macromorphology were observed with optical microscopy and the roughness values for the surface finish were calculated from profilometer data. Furthermore, samples were submerged in water and weighed periodically to measure mass changes due to water absorption. From surface profilometry and optical miscopy data, mechanical media blasting, epoxy coating, and immersion in all concentrations of acetone decreased surface roughness. Overall, on average, grit blasting with large beads and epoxy coating led to 2.6% and 1.2% increases in tensile strength, respectively; immersion in 40% acetone led to a 1.9% increase in tensile strength while treatment in 60% and 80% acetone decreased tensile strength by 4.9% and 1.9%, respectively. The study concludes that only grit blasting with large beads, immersion in 60% acetone, and the ridged texture significantly affected the tensile strength.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Transformation Kinetics of Phosphorus and Nitrogen in Iron-Rich Sewage Sludges during Hydrothermal Treatment and Recovery of Nutrients from Process Water

Hydrothermal treatment (HT) is an emerging technique for sustainable sewage sludge management and resource recovery. Many sludges are rich in iron (Fe) due to the common addition of Fe salts in water resource recovery facilities. To develop guidance for reaction conditions targeting nutrient recovery, this study systematically investigated the influence of HT temperature, treatment time, and sludge source on the dynamic speciation evolution of phosphorus (P) and nitrogen (N) during HT of Fe-rich sewage sludge. Complementary chemical extraction and X-ray spectroscopy analyses were conducted to characterize the treatment products. For the sludge mixture (a blend of primary and waste activated sludges), P speciation did not change significantly within 4.5 h at 125 °C HT, while soluble and labile P was converted into insoluble P over time at 175 and 225 °C HT. Strengite (FePO 4 · 2 H 2 O) preferentially formed in the hydrochars with increasing treatment temperature and/or time, whereas 125 °C HT within 1.5 h favored the formation of vivianite (Fe 3 (PO 4 ) 2 ·8H 2 O). Organic P was completely decomposed into orthophosphate when the HT temperature reached up to 175 °C. Pyrrole-N was enriched in the hydrochars. Similar reaction pathways were observed during HT of anaerobically digested sludge, though some minor differences in Fe-associated P and organic P were observed. Meanwhile, HT of the two sludges released orthophosphate and ammonia into the process waters at 175 and 225 °C, which can be recovered by a sequential process involving struvite (MgNH 4 PO 4 ·6H 2 O) precipitation and air stripping. This study provides new insights into the transformation of P and N during HT of Fe-rich sludges as well as a modular design for maximum P and N recovery from the treatment products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

A transcriptome software comparison for the analyses of treatments expected to give subtle gene expression responses

Background: In this comparative study we evaluate the performance of four software tools: DNAstar-D (DESeq2), DNAstar-E (edgeR), CLC Genomics and Partek Flow for identification of differentially expressed genes (DEGs) using a transcriptome of E. coli. The RNA-seq data are from the effect of below-background radiation 5.5 nGy total dose (0.2nGy/hr) on E. coli grown shielded from natural radiation 655 m below ground in a pre-World War II steel vault. The gene expression response to three supplemented sources of radiation designed to mimic natural background, 1952 – 5720 nGy in total dose (71–208 nGy/hr), are compared to this “radiation-deprived” treatment. In addition, RNA-seq data of Caenorhabditis elegans nematode from similar radiation treatments was analyzed by three of the software packages. Results: In E. coli, the four software programs identified one of the supplementary sources of radiation (KCl) to evoke about 5 times more transcribed genes than the minus-radiation treatment (69–114 differentially expressed genes, DEGs), and so the rest of the analyses used this KCl vs “Minus” comparison. After imposing a 30-read minimum cutoff, one of the DNAStar options shared two of the three steps (mapping, normalization, and statistic) with Partek Flow (they both used median of ratios to normalize and the DESeq2 statistical package), and these two programs identified the highest number of DEGs in common with each other (53). In contrast, when the programs used different approaches in each of the three steps, between 31 and 40 DEGs were found in common. Regarding the extent of expression differences, three of the four programs gave high fold-change results (15–178 fold), but one (DNAstar’s DESeq2) resulted in more conservative fold-changes (1.5–3.5). In a parallel study comparing three qPCR commercial validation software programs, these programs also gave variable results as to which genes were significantly regulated. Similarly, the C. elegans analysis showed exaggerated fold-changes in CLC and DNAstar’s edgeR while DNAstar-D was more conservative. Conclusions: Regarding the extent of expression (fold-change), and considering the subtlety of the very low level radiation treatments, in E. coli three of the four programs gave what we consider exaggerated fold-change results (15 – 178 fold), but one (DNAstar’s DESeq2) gave more realistic fold-changes (1.5–3.5). When RT-qPCR validation comparisons to transcriptome results were carried out, they supported the more conservative DNAstar-D’s expression results. When another model organism’s (nematode) response to these radiation differences was similarly analyzed, DNAstar-D also resulted in the most conservative expression patterns. Therefore, we would propose DESeq2 (“DNAstar-D”) as an appropriate software tool for differential gene expression studies for treatments expected to give subtle transcriptome responses.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Tensile Performance Sensitivity to Variations of Standard 17-4 PH Heat Treatments on LPBF-Produced Material

Standard heat treatments for metals of a particular composition are typically designed with the assumption of a conventional starting microstructure, such as that produced by casting or wrought processing. When applied to metals fabricated by Laser Powder Bed Fusion (LPBF) metal additive manufacturing (AM), these heat treatments can produce inconsistent performance due to the unique as-built microstructures. This study investigates how modifications to standard heat treatments for 17-4 PH steel influence the microstructure and mechanical properties of LPBF-fabricated material. Specimens were produced and subjected to varying solutionizing and homogenizing treatments followed by standard aging treatments. Microstructures were characterized using optical microscopy, Electron Backscatter Diffraction (EBSD), and X-ray diffraction (XRD), and mechanical properties were evaluated through uniaxial tensile testing. Based on these results, recommendations are provided for achieving improved wrought-like performance in LPBF 17-4 PH steel.

17-4 PH↗

NASA NTRS2023

Paint and Oil Locker, SWMU 067 Southern Treatment Area Air Sparge System Construction Completion and Performance Monitoring and Paint and Oil Locker, Northern Area (SWMU 067) and Supply Warehouse #3, SWMU 088 Long-Term Monitoring Report Kennedy Space Center, Florida

This Air Sparge (AS) System Construction Completion, Performance Monitoring, and Long-Term Monitoring (LTM) Report presents activities conducted at the Paint and Oil Locker (POL) (Solid Waste Management Unit [SWMU] 067) and Supply Warehouse #3 (SW3) (SWMU 088) sites located at the Kennedy Space Center (KSC), Florida. Activities include implementation and Year 1 (Quarters [Q] 1 through 4) and Q5 operation, maintenance, and monitoring (OM&M) activities and performance monitoring results for the AS Interim Measure (IM) in the POL Southern Treatment Area, LTM results for the POL Northern Area and SW3, and supplemental direct push technology (DPT) sampling at both sites to support the LTM and performance monitoring programs. The timeframe for activities included in this report extends from August 2019 to August 2022. The scope for these sites currently includes two main components, which are documented within this report: (1) LTM at SW3 and POL Northern Area where an AS system began operation at these sites in May 2009 and June 2013, respectively, and subsequently turned off for both sites in March 2018 (during the previous reporting period); and (2) Active AS operations and performance monitoring in the POL Southern Treatment Area where an AS system was installed and began operation in 2021. The AS IM in the POL Southern Treatment Area was implemented between 2019 and 2021 to treat a chlorinated solvent groundwater plume that resulted from historic operations supporting the National Aeronautics and Space Administration’s (NASA) Space Program. The objective of the AS IM is to remediate groundwater within the treatment zone to support transition to monitored natural attenuation (MNA). The overall Corrective Action objective is to reduce concentrations of trichloroethene (TCE), cis-1,2-dichloroethene (cDCE), trans-1,2- dichloroethene (tDCE), and vinyl chloride (VC) present in groundwater to levels below their respective State of Florida Groundwater Cleanup Target Levels (GCTLs). The AS IM was installed in the POL Southern Treatment Area to target the high concentration plume (HCP), which includes a source zone (SZ) area where TCE was found to exceed 11,000 micrograms per liter (µg/L), and extend to a depth of 30 feet below land surface (bls).

TCE↗

NASA NTRS2024

Aeroelastic Stability Assessment Methodology and Application to Slat Noise Treatments on the High-Lift Common Research Model

This work supports a larger effort at NASA to reduce airframe noise and, thus, environmental noise around airports. The leading-edge slat of conventional high-lift systems is a prominent source of airframe noise, and two technologies were previously identified as promising for noise reduction without significant aerodynamic or weight penalty: the slat cove filler (SCF) and the slat gap filler (SGF). NASA fabricated a 10%-scale semispan aircraft model for wind tunnel testing based upon the High-Lift Common Research Model (CRM-HL). NASA embarked on a test campaign with the 10% CRM-HL to determine the noise reduction effectiveness and other performance metrics of 3D SCF and SGF treatments in flow conditions representative of flight. The highly flexible SCF and SGF treatments posed a risk to the model and aeroelastic instability would compromise research integrity, so aeroelastic stability assessment was required. This work briefly describes the 10% CRM-HL, design of the SCF and SGF treatments to the model, and supporting fluid structure interaction (FSI) research. Relations for static and dynamic aeroelastic similitude are then developed for convenience of reference, and simplifications are introduced of particular utility to the cases considered in this study. The similitude relations are employed to assess the stability of the treatments under wind tunnel flow conditions based upon known behaviors from the supporting research. It is shown that the treatments are safe for test under the anticipated wind tunnel flow conditions with significant margins/factors of safety. It is furthermore demonstrated that the SCF is more susceptible to aeroelastic instability than the SGF, which has implications for flight feasibility.

Similitude↗

DOE OSTI2026

Enhancing mobility and interface state engineering via UV-ozone treatment in BEOL-compatible ultrathin TiO 2 transistors

It has emerged as a potential candidate to improve the performance of monolithic-three-dimensional (M3D) integration of fused logic and memories through low-temperature in situ synthesis of high-performance metal–oxide–semiconductor (MOS) transistors. Here, we report the demonstration of the BEOL-compatible low thermal budget (350 °C) fabrication process of ultrathin-TiO2 transistors by the combination of RTA and UV-ozone treatment (RTA-UVOz). UV–ozone (UVOz) treatment of TiO2 anatase films significantly enhances stability, boosting ION current and field effect mobility (μ FE ) by two times of magnitude in TiO2 TFTs. UV ozone treatment helps to eliminate pre-existing oxygen vacancies and carbon contamination on TiO2 channels even at low temperature (100 °C), resulting in high-quality channel/dielectric interfaces with low interface states (D it ). During UVOz treatment, oxygen species (O x ) passivate the oxygen vacancies ($V$$^{2+}_{o}$), and hence low concentration of $V$$^{2+}_{o}$ would be left for ionization/de-ionization under PBS/NBS, leading to improved bias stress stability. Furthermore, the TiO 2 TFTs with thin ZrO 2 gate dielectric exhibited excellent performance including a lower subthreshold swing (SS) of 98 mV/dec with high drive I ON current ∼ 4.5 μA/μm, a high I ON /I OFF > 10 9 , and mobility μFE of 7 cm 2 /V-s under a battery powered voltage of 1 V. UV–ozone treatment enables high-performance, CMOS-compatible TiO 2 transistors with a low thermal budget, ideal for next-generation flexible, energy-efficient electronics.

BEOL↗

DOE OSTI2022

A novel approach for produced water treatment: Supercritical water oxidation and desalination

Produced water generated from oil and gas operations contains significant quantities of environmentally hazardous hydrocarbons, organic chemicals, and inorganic salts. Environmental regulations with impaired water disposal mandates produced water treatment and desalination. Industry standard desalination technologies are energy-intensive and mandate extensive produced water pre-treatment including removal of hydrocarbons constituents for efficient operations. Herein this study investigates a novel process intensification approach integrating supercritical water oxidation (SCWO) unit operation with a supercritical water desalination (SCWD) process for energy efficient produced water treatment and desalination. The coupled SCWD-SCWO process is found to be very energy-efficient and cost effective than existing industry standard desalination technologies. For energy efficient operation, the heat generated from the SCWO of hydrocarbons present in the produced water is used for power generation using a high efficiency and low-cost re-heat Rankine cycle process. The cost of treating produced water with proposed SCWO-SCWD process is independent of the salt concentration. The proposed process has the potential to offer step-change improvements over conventional processes in both the efficiency and cost of produced water treatment: for example, a cost and energy saving of 70% and 100% is calculated for the treatment of produced water containing 250 g/l salt and 10.6 g/l hydrocarbon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Influence of Thermal Treatment on Preceramic Polymer Grafted Nanoparticle Network Formation: Implications for Thermal Protection Systems and Aerospace Propulsion Components

Preceramic polymer grafted nanoparticles (PCP GNPs) offer potential advantages in the production of polymer-derived ceramic composites compared to neat preceramic polymers (PCPs), such as reduced thermal shrinkage and increased char yield. In comparison to traditional composites (particles + free polymer), PCPs avoid issues of compatibility, agglomeration, and phase separation during processing and provide routes to control nanoparticle arrangement. Prior literature has established that the conversion efficiency of PCPs and PCP GNPs to ceramics and ceramic composites is linked to the thermal pretreatment of these precursor polymers (e.g., curing). In this paper, we investigate the material transformations that occur when exposing PCP GNPs to a low-temperature thermal treatment (≤250 °C) prior to pyrolysis. The PCP GNPs explored in this study possessed silica nanoparticle cores but were distinct in their PCP coronas, having poly(1,1-dimethylpropylsilane) (allyl-GNP)- or poly(1,1-dimethylbenzylethylsilane) (styryl-GNP)-grafted polymers. After undergoing low-temperature thermal treatment, these PCP GNPs exhibited increased char yield at 800 °C; however, unlike commercial PCPs (e.g., allylhydridopolycarbosilane (SMP-10)), obvious cross-linkable sites are not present in the PCP corona structure. Differential scanning calorimetry, oscillatory rheology, and X-ray photon correlation spectroscopy were utilized to elucidate the thermally induced material changes in the allyl- and styryl-GNPs. Thermally induced changes to the structure and behavior of the PCP GNPs were determined to be linked to the chemical structure of the grafted polycarbosilane chains. Styryl-GNPs experienced a curing event between 180 and 250 °C, effecting the formation of a network, which contributed to char yield improvement (at 800 °C). The nanoscale dynamics of this material also shows a transition from diffuse behavior to ballistic behavior because of the cross-linking event. Conversely, the allyl-GNPs did not exhibit a curing event under heat treatment but did show an increase in thermally induced physical cross-linking. The allyl-GNP physical network is stronger after the first cycle of thermal treatment, and it is considered that this contributed to the improvement in char yield post thermal treatment. The advancements in the understanding of the cross-linking behavior of these hybrid materials are expected to advance the application of these materials to turbine engine, advanced friction, and heat-shielding components.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Performance Evaluation of a High Salinity Produced Water Treatment Train: Chemical Analysis and Aryl Hydrocarbon Activation

Water scarcity and increased energy demands have put a strong focus on improving industries at the heart of the water–energy nexus. Treatment of oil and gas produced water (PW) can help reduce freshwater consumption during hydraulic fracturing, especially in arid regions, while also removing harmful contaminants from entering the environment. However, it is also difficult to treat because PW contains high concentrations of many environmentally toxic contaminants, which require complex and expensive treatment processes to achieve their removal. To demonstrate the possibility of PW treatment and reuse in the O&G industry, a comprehensive environmental toxicity and water quality analysis throughout a five-process treatment train was performed on high salinity (>120 g/L) Permian basin raw PW. Here, the concentrations of naturally occurring radioactive materials were reduced by over 99%, total organic carbon was reduced by 93%, and inorganic constituents, including total dissolved solids, were reduced by over 99%. Compounds that induced the aryl hydrocarbon receptor and caused cytotoxicity in MCF-7 cells were also removed. Overall, the results of this study show that a short treatment train (five distinct unit processes) can be effective in treating PW to a level suitable for use outside of the oil industry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Chelator-mediated Fenton post-treatment enhances methane yield from lignocellulosic residues via microbial community modulation

Advancing biomethane production from anaerobic digestion (AD) is essential for building a more reliable and resilient bioenergy system. However, incomplete conversion of lignocellulose-rich agricultural waste remains a key limitation, often leaving energy-dense residues in the digestate by-product. In this study, we introduce a novel application of chelator-mediated Fenton (CMF) post-treatment to recover untapped biomethane potential from these recalcitrant residues, representing a significant departure from conventional pre-treatment strategies. By systematically varying pH, iron-chelator concentration, and hydrogen peroxide dosage, we identified reaction conditions (pH 6–8, 5 mM Fe 2+ -dihydroxybenzene, 3–4 wt.% H 2 O 2 ) that enhanced lignocellulose deconstruction and increased dissolved organic carbon (DOC) availability for methanogenesis. CMF post-treatment led to up to a tenfold increase in biomethane potential compared to untreated controls. Microbial community analysis revealed enrichment of cellulolytic species, suggesting enhanced hydrolytic activity as a driver of improved conversion. Application of the CMF post-treatment method to isolated poplar lignin further demonstrated its versatility for diverse lignocellulosic substrates. These findings position CMF post-treatment as a promising strategy to enhance AD efficiency and valorize digestate.

Martinez, Daniella Victoria [Sandia National Labor↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2025

Baseline Cost Analysis of Energy Wastewater Treatment with Preliminary Feasibility Analysis of Critical Mineral Recovery

Critical mineral recovery from wastewater is an enhancement of conventional mining that can help meet growing demand. This work investigates two energy wastewaters that have previously been shown to be enriched in critical minerals, oil and gas produced water in the Permian Basin and combustion residual leachate. Treatment of these two wastewaters using reverse osmosis or thermal-based methods concentrates critical minerals, which improves the economic viability of critical mineral recovery. Revenue from mineral recovery could also offset treatment costs for operators. This work evaluates the cost of treatment for each wastewater and evaluates the potential revenue from critical minerals concentrated in the brine. The levelized cost of water for combustion residual leachate ranges from USD 1.90 to USD 16.20 (USD 2023/m 3 permeate) and for produced water ranges from USD 14.40 to USD 24.30 (USD 2023/m 3 distillate). Recovery opportunities range from USD 0.11 to USD 1.13 (USD 2023/m 3 permeate) for leachate and from USD 8.28 to USD 42.10 (USD 2023/m 3 distillate) for produced water, dominated by the value of magnesium and lithium. Comparing the maximum value of critical minerals contained in produced water and the maximum treatment costs, the value of critical minerals exceeds the cost of treatment by USD 17.80/m 3 distillate, which signals a potential revenue opportunity.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2024

Enhancing Acute Migraine Treatment: Exploring Solid Lipid Nanoparticles and Nanostructured Lipid Carriers for the Nose-to-Brain Route

Migraine has a high prevalence worldwide and is one of the main disabling neurological diseases in individuals under the age of 50. In general, treatment includes the use of oral analgesics or non-steroidal anti-inflammatory drugs (NSAIDs) for mild attacks, and, for moderate or severe attacks, triptans or 5-HT1B/1D receptor agonists. However, the administration of antimigraine drugs in conventional oral pharmaceutical dosage forms is a challenge, since many molecules have difficulty crossing the blood-brain barrier (BBB) to reach the brain, which leads to bioavailability problems. Efforts have been made to find alternative delivery systems and/or routes for antimigraine drugs. In vivo studies have shown that it is possible to administer drugs directly into the brain via the intranasal (IN) or the nose-to-brain route, thus avoiding the need for the molecules to cross the BBB. In this field, the use of lipid nanoparticles, in particular solid lipid nanoparticles (SLN) and nanostructured lipid carriers (NLC), has shown promising results, since they have several advantages for drugs administered via the IN route, including increased absorption and reduced enzymatic degradation, improving bioavailability. Furthermore, SLN and NLC are capable of co-encapsulating drugs, promoting their simultaneous delivery to the site of therapeutic action, which can be a promising approach for the acute migraine treatment. This review highlights the potential of using SLN and NLC to improve the treatment of acute migraine via the nose-to-brain route. First sections describe the pathophysiology and the currently available pharmacological treatment for acute migraine, followed by an outline of the mechanisms underlying the nose-to-brain route. Afterwards, the main features of SLN and NLC and the most recent in vivo studies investigating the use of these nanoparticles for the treatment of acute migraine are presented.

Torres, Joana (ORCID:0000000327276229)↗

NASA NTRS1975

A study of casing treatment stall margin improvement phenomena

The results of a program of experimental and analytical research in casing treatments over axial compressor rotor blade tips are presented. Circumferential groove, axial-skewed slot and blade angle slot treatments were tested at low speeds. With the circumferential groove treatment the stalling flow was reduced 5.8% at negligible efficiency sacrifice. The axial-skewed slot treatment improved the stalling flow by 15.3%; 1.8 points in peak efficiency were sacrificed. The blade angle slot treatment improved the stalling flow by 15.0%; 1.4 points in peak efficiency were sacrificed. The favorable stalling flow situations correlated well with observations of higher-than-normal surface pressures on the rotor blade pressure surfaces in the tip region, and with increased maximum diffusions on the suction surfaces. Annulus wall pressure gradients, especially in the 50 to 75% chord region, are also increased and blade surface pressure loadings are shifted toward the trailing edge for treated configurations.

Prince, D. C., Jr.↗

NASA NTRS1977

Inlet total pressure loss due to acoustic wall treatment

Experimental determination of the effect of diffuser wall acoustic treatment on inlet total pressure loss. Data were obtained by testing an inlet model with 10 different acoustically treated diffusers differing only in the design of the Helmholtz resonator acoustic treatment. Tests were conducted in a wind tunnel at forward velocities to 41 meters per second for inlet throat Mach numbers of .5 to .8 and angles of attack as high as 50 degrees. Results indicate a pressure loss penalty due to acoustic treatment that increases linearly with the porosity of the acoustic facing sheet. For a surface porosity of 14% the total pressure loss was 21% greater than that for an untreated inlet. The penalty resulting from treatment increased for average throat Mach numbers above approximately .7 where local regions of sonic or supersonic surface flow were encountered. Pressure loss over the treatment was not affected by the presence of noise.

Miller, B. A.↗