Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transformer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The effects of Ti content and quenching on phase transformations, microstructures, and mechanical properties in uranium-titanium alloys

In this work, the effect of Ti content on phase transformations, microstructures, and mechanical properties of U-Ti alloys are described for alloys containing 0.3 wt.% to 2.0 wt.%Ti. Rapid cooling is required to overcome diffusional decomposition of γ-phase and facilitate diffusionless transformation to supersaturated variants of α-phase. Critical cooling rate increases with increasing Ti content, opposite to the trend observed in U-Mo and U-Nb alloys. This difference occurs because the martensite transformation temperatures in these relatively dilute U-Ti alloys are above the knee of the C-curve for diffusional decomposition, unlike those in the more concentrated U-Mo and U-Nb alloys. In these U-Ti alloys critical cooling rate depends on the amount of undercooling required to reach M s , which increases with increasing Ti content, and the time for diffusional decomposition to occur just above M s , which decreases with increasing Ti content. The net result is that higher cooling rates are required as Ti content increases. Full quenching results in diffusionless transformation of γ-phase to supersaturated variants of α-phase. Very dilute alloys transform via a γ → β → α m sequence of massive transformations. Martensitic γ → α' a transformation begins at ~0.4%Ti, and 100% α' a microstructures are obtained from ~0.65% to ~1.4% Ti. A transition to banded α'b martensite occurs at ~1.5%Ti. Evidence suggests that the α' a to α' b transition may occur when the cubic γ-phase first transforms to tetragonal γ°, which in turn transforms to orthorhombic α' b via the sequence γ → γ° → α' b . Fully quenched alloys exhibit moderate strengths and ductilities, and their supersaturation with Ti makes them amenable to subsequent age hardening. Subcritical quenching typically results in two-phase microstructures with lower ductilities and near-zero Ti-supersaturation, eliminating the possibility of subsequent age hardening.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Low-cost embedded optical sensing systems for distribution transformer monitoring

There is a mounting need for low-cost monitoring with online sensing technologies to maintain grid reliability and uptime. Here we introduce an innovative low-cost, embedded optical sensing technology initially focused on transformers that was developed and demonstrated at a major electric utility, Con Edison. A version of it that can be retrofitted onto existing transformers in the field was also developed. Two new 500 kVA distribution network transformers were built with embedded fiber-optic (FO) sensors and qualified per industry standards. Vibration, temperature, and corrosion were key parameters monitored. The first transformer with embedded FO sensors was installed at a Con Edison facility and monitored at our team’s office. The second one was installed in an urban street-side underground location with online data processing/feature extraction algorithms and monitored through a wireless router. Additionally, an older transformer was also retrofitted. Data analysis was done on these transformers showing promising correlations with their corresponding loading cycles. Furthermore, key events such as the transformer primary-side energizing, and other events were detected. In general, the technology was demonstrated over 6 months across the 3 transformers instrumented with promising results. Thus, it has the potential to enable predictive maintenance for transformers and other grid assets.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Geomagnetically Induced Current Field Test on Large Grid-Connected Power Transformers: Analysis, Model Development, and Simulations

Geomagnetic-induced current (GIC) flow in power grids can cause undesirable effects such as transformer overheating, harmonics, higher reactive power demand, etc. Many simulation models have been developed to study these effects, but real-world verification on modern transformer designs is rare. Here, this paper presents the first long-duration GIC field test in the U.S. performed on high-voltage, grid-connected transformers featuring winding clamps and tie rods instead of conventional tie bars. Field measurements were taken to evaluate GIC effects. These measurements also aided in developing and validating thermal and electromagnetic transient (EMT) models of the transformers. During the test, significant current and voltage distortions were observed along with considerable transformer reactive power losses. Analysis of the field measurements showed that the transformers’ hottest spot was at the inner windings, and their k-factors were close to factory test and software default values. Thermal simulations indicated that the transformers would not violate their thermal limits even for a GIC waveform that peaks at about 200 A/phase. EMT simulations revealed that increased transformer loading may reduce GIC-induced reactive power demand and harmonics in certain scenarios. The study also highlighted potential inaccuracies in using the k-factor method to calculate transformer reactive power losses.

EMTDC↗
DOE OSTI2021

Retaining Geochemical Signatures during Aragonite-Calcite Transformation at Hydrothermal Conditions

Transformation of aragonite, a mineral phase metastable at Earth’s surface, to calcite widely occurs in both sedimentary and metamorphic systems with the presence of an aqueous phase. The transformation process can affect geochemical signatures of aragonite (a protolith). This study focused on quantification of the retention of Mg/Ca and Sr/Ca ratios, and δ18O during the transformation process as well as evaluation of the transformation rate. To investigate the effect of transformation from aragonite to calcite on elemental and stable isotope ratios, we conducted a series of experiments in NaCl solutions at temperatures between 120 and 184 °C. Two additional experiments at 250 °C were conducted to estimate the transformation rate of aragonite to calcite. Protolith materials consist of (1) synthetic (Mg; Sr-bearing or non-Mg; Sr bearing) needle-shaped microcrystals of aragonite (<5 µm in size) and (2) larger chips (>100 µm in size) of natural aragonite. X-ray diffraction (XRD) showed that microcrystals successfully transformed to calcite within 30 h and scanning electron microscopy (SEM) yielded a change in the crystal size to >10 µm in rhombohedral shape. Electron backscatter diffraction (EBSD) of the larger aragonite chips showed that transformation to randomly oriented calcite occurred at the rims and along the cracks while the core retained an aragonite crystal structure. Isotope-ratio mass spectrometry (IRMS) analyses showed that calcite δ18O was controlled by temperature and δ18O of the solution. The obtained calibration curve of isotope fractionation factor versus temperature is consistent with other studies. Inductively coupled plasma optical emission spectroscopy (ICP-OES) analyses showed that calcite partially or completely retained Mg/Ca and Sr/Ca ratios through the transformation.

58 GEOSCIENCES↗
DOE OSTI2020

Tuning martensitic transformations via coherent second phases in nanolaminates using free energy landscape engineering

In this work we explore the possibilities and limitations of using a coherent second phase to engineer the thermo-mechanical properties of a martensitic alloy by modifying the underlying free energy landscape that controls the transformation. We use molecular dynamics simulations of a model atomistic system where the properties of a coherent, nanoscale second phase can be varied systematically. With a base martensitic material that undergoes a temperature-induced transformation from a cubic austenite to a monoclinic martensite, simulations show significant ability to engineer the transformation temperatures, from a ~50% reduction to a ~200% increase, with 50 at.% of the cubic second phase. We establish correlations between the properties of the second phase, the transformation characteristics, and the microstructure via the free energy landscape of the twophase systems. Coherency stresses have a strong influence on the martensitic variants observed and can even cause the non-martensitic second phase to undergo a transformation. Reducing the stiffness of the second phase increases the transformation strain and modifies the martensitic microstructure, increasing the volume fraction of the transformed material. This increase in transformation strain is accompanied by a significant increase in Af and thermal hysteresis, while Ms remains unaltered. Our findings on the tunability of martensitic transformations can be used for informed searches of second phases to achieve desired material properties, such as achieving room temperature, lightweight shape memory alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

On the accuracy of compressibility transformations

This study highlights the importance of satisfying the eddy viscosity equivalence below the logarithmic layer, to deriving accurate compressibility transformations. First, we analyze the ability of known transformations to satisfy the eddy viscosity equivalence and show that the accuracy of these transformations is strongly dependent on this ability. Second, in a step-by-step manner, we devise new transformations that satisfy this hypothesis. An approach based on curve fitting of the incompressible Direct Numerical Simulation data for eddy viscosity profiles below the logarithmic layer provides an extremely accurate transformation, which motivates self-contained methods, making use of mixing length formulas in the inner region. It is shown that the accuracy of existing transformations can be significantly improved by applying these ideas, below the logarithmic layer. Motivated by the effectiveness of the formulations derived from eddy viscosity equivalence, we introduce a new integral transformation based on Reynolds number equivalence between compressible and incompressible flows. This approach is based on defining a new compressible velocity scale, which affects the accuracy of transformations. Several choices for the velocity scale are tested, and in each attempt, it is shown that the eddy viscosity equivalence plays a very important role for the accuracy of compressibility transformations.

42 ENGINEERING↗
DOE OSTI2024

Assessment of Current MACCS Capabilities for Modeling Atmospheric Physical and Chemical Transformations

The physical and chemical transformation during atmospheric transport of radionuclides released into the environment has the possibility of impacting consequence modeling results. Accordingly, this report identifies physical and chemical transformations that may occur following release of chemically reactive radioactive species, how those transformations may affect modeling of consequences of release to the atmosphere and identifies current capabilities – in both MACCS and other state-of-practice atmospheric transport and dispersions models– to model those transformations. It was found that the inclusion of physical and chemical transformations is currently very limited in current state-of-practice codes for atmospheric dispersion of radionuclides. State-of-practice atmospheric dispersion codes appear to be typically limited to simulating either physical-chemical transformations or radioactive transformations, but not both. A state-of-practice atmospheric dispersion code capable of performing parallel physical, chemical, and radioactive transformation was not identified. A few atmospheric dispersion codes capable of modeling physical and chemical transport of specific species such as tritium or uranium hexafluoride were identified. Consequently, there is currently no information available that clearly suggests updates to the MACCS code are needed to bring it up to state-of-practice. However, investigations concluded that the MACCS computational framework can currently accommodate multiple physical/chemical forms in one simulation. Additionally, with some major assumptions, the computational framework in MACCS can accommodate parallel physical-chemical and radioactive transformations.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Reconfigurable unitary transformations of optical beam arrays

Spatial transformations of light are ubiquitous in optics, with examples ranging from simple imaging with a lens to quantum and classical information processing in waveguide meshes. Multi-plane light converter (MPLC) systems have emerged as a platform that promises completely general spatial transformations, i.e., a universal unitary. However, until now, MPLC systems have demonstrated transformations that are far from general, e.g., converting from a Gaussian to Laguerre-Gauss mode. Here, we demonstrate the promise of an MLPC, the ability to impose an arbitrary unitary transformation that can be reconfigured dynamically. Specifically, we consider transformations on superpositions of parallel free-space beams arranged in an array, which is a common information encoding in photonics. We experimentally test the full gamut of unitary transformations for a system of two parallel beams and make a map of their fidelity. We obtain an average transformation fidelity of 0.85 ± 0.03. This high-fidelity suggests that MPLCs are a useful tool for implementing the unitary transformations that comprise quantum and classical information processing.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Uncovering the role of nanoscale precipitates on martensitic transformation and superelasticity

Here we characterize the role of coherent nanoscale B2 Ni 50 Al 50 precipitates on the temperature- and stress-induced martensitic phase transformation in nanocrystalline Ni 63 Al 37 shape memory alloys using multi-million-atoms molecular dynamics (MD) simulations. We studied two types of precipitates: one with single crystal precipitates (SXP) and a second where grain boundaries cut through precipitates (PXP). Simulations reveal that the presence of B2 precipitates stabilizes the cyclic flag-shaped stress-strain response, characteristic of superelasticity, and reduces remnant strain. In contrast, single-phase nanocrystalline Ni 63 Al 37 exhibits degradation of the reverse transformation during cyclic loading and, eventually, incomplete reversible transformation within a few cycles. This is consistent with previous experimental findings of ultra-low fatigue in Ni-Ti-Cu alloys with Ti 2 Cu precipitates. The simulations reveal that the presence of precipitates significantly improves the reversibility of the transformation by acting as elastic zones that partially shield the martensitic transformation and drive the reverse transformation. A detailed analysis of the MD trajectories reveals that the martensitic transformation of the matrix induces ultra-large elastic deformation in some of the B2 precipitates (approximately 12%) to the point of resulting in a martensite-like atomic structure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of laser scanning speed on the microstructure, phase transformation and mechanical property of NiTi alloys fabricated by $\mathrm{LPBF}$

This study investigated the effects of laser scanning speed on the microstructure, phase transformation and properties of NiTi alloys fabricated by laser powder bed fusion (LPBF). In this study, the contributions of metallurgical factors under different scanning speeds, such as Ni evaporation, Ni4Ti3 precipitation, dislocations and internal stress, to the transformation temperature and transformation latent heat were clarified through specially designed experiments. Ni evaporation is found to have the most profound effect, followed by precipitation. Increasing scanning speed is found to reduce Ni loss, thus cause less increase in the transformation temperature and transformation heat of the LPBF-NiTi alloys. Increasing scanning speed also increases the microstructure non-uniformity and thus widens the transformation temperature interval. The orientations of residual stress exhibit strong crystallographic stiffness dependence. The LPBF-NiTi alloys with different scanning speeds all exhibited high strains (>13.4%) and excellent shape memory effect. A LPBF-NiTi honeycomb structure exhibited 96% shape recovery rate after a 60% pre-compressive deformation. Besides, there is an optimum scanning speed for minimum porosity and smallest average pore size. However, the pore structure is found to have weak influence on the tensile behaviour of the LPBF-NiTi alloys, possibly due to the high defect tolerance of the martensitic transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Restoring permutational invariance in the Jordan–Wigner transformation

The Jordan–Wigner transformation is a powerful tool for converting systems of spins into systems of fermions, or vice versa. While this mapping is exact, the transformation itself depends on the labelling of the spins. One consequence of this dependence is that approximate solutions of a Jordan–Wigner-transformed Hamiltonian may depend on the (physically inconsequential) labelling of the spins. In this work, we turn to an extended Jordan–Wigner transformation which remedies this problem and which may also introduce some correlation atop the Hartree–Fock solution of a transformed spin Hamiltonian. We demonstrate that this extended Jordan–Wigner transformation can be thought of as arising from a unitary version of the Lie algebraic similarity transformation (LAST) theory. Here, we show how these ideas, particularly in combination with the standard (non-unitary) version of LAST, can provide a potentially powerful tool for the treatment of the XXZ and J 1 –J 2 Heisenberg Hamiltonians.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Thermally activated structural transformations in manganese oxide nanoparticles under air and argon atmospheres

The properties of manganese oxide nanomaterials are dictated by the structure and morphology of the particular phases they can adopt. The effects of post-synthesis heat treatments on amorphous monodisperse manganese oxide nanoparticles at ≤1300° under lab. air and argon atmospheres were investigated using X-ray diffraction, thermal analysis and electron microscopy techniques. During heat treatments in air, the nanoparticles undergo three transformations, resulting in: crystallization to cubic Mn 2 O 3 at ~500°, followed by the transformation to tetragonal Mn 3 O 4 at ~1010°, and to cubic Mn 3 O 4 at ~1190°. The first two transformations are irreversible, are associated with oxygen loss, and involve reductions. of the Mn ions. The latter transformation is polymorphic and spontaneously reversible, and so, tetragonal Mn 3 O 4 is observed at ambient temperature in samples heat-treated at >1000°. The samples heat treated in argon firstly crystallize to a mixt. of monoclinic Mn 2 O 3 and tetragonal Mn 3 O 4 at ~475°, followed by complete transformation to tetragonal Mn 3 O 4 at ~820°, and then to mostly cubic MnO at ~1145°; here again, the residual tetragonal Mn 3 O 4 undergoes a reversible polymorphic transformation at ~1180°, whereas the other transformations are irreversible. In both atmospheres, the amorphous material exhibits short-range cryptomelane-type order with a mixture of Mn 3+ and Mn 4+ prior to crystallization. Furthermore, these data indicate that most of the stable manganese oxide phases can be obtained from initially amorphous nanoparticles by heat treatment under appropriate conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

MnBi-based magnets prepared from melt-spun alloys: Effect of $α → β$ phase transformation during field annealing

The temperature of the annealing treatment applied to the MnBi alloys with the intention to stabilize the α -MnBi “low-temperature” phase – a promising material for the rare-earth-free permanent magnets – is usually kept below the range of the β -Mn 1.08 Bi “high-temperature” phase. This work is focused on the investigation of the effects of partial and complete α → β phase transformation in bulk magnetic-field-annealed magnets on their structure and magnetic properties. MnBi alloys modified with In, Mg and Sb were melt-spun, compacted to their full density and then heated in a magnetic field of 30 kOe to temperatures sufficiently high for the beginning of the α → β transformation. A heating of 15 °C/min was used which was immediately followed by cooling at the rate of 7.5 °C/min; the degree of the phase transformation was measured by in situ monitoring of changes in the sample magnetization. In all the studied alloys, the α → β transformation was found to improve the [0 0 1] fiber texture induced by the applied magnetic field, although it simultaneously decreased the coercivity. A partial transformation has resulted in a 11% increase of the maximum energy product for the Mn 50 Bi 49 Sb 0.5 In 0.5 magnet, to 8.3 MGOe, and a 3% increase for the Mn 50 Bi 46 Mg 3 Sb 0.5 In 0.5 magnet, to 12.8 MGOe. In the latter alloy, the α → β and reverse transformations were found to initially occur in well-defined pockets leading to clusters of large, highly textured α crystallites. In the Mn 50 Bi 48.5 Sb 1.5 magnet, only part of the α phase could be recovered after the transformation, which instead promoted the paramagnetic MnBi 0.9 Sb 0.1 phase.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Experimental determination of critical resolved shear stress for strain-induced phase transformation

The current investigation reports the first attempt to measure the critical resolved shear stress to initiates strain-induced phase transformation in a three-dimensional polycrystalline aggregate using high-energy diffraction microscopy (HEDM). In situ tensile testing was performed on a Fe38.5Mn20Co20Cr15Si5Cu1.5 metastable alloy exhibiting transformation-induced plasticity (TRIP). Grains with a higher propensity for strain-induced phase transformation were tracked using HEDM. A sharp drop in grain specific stress, coinciding with the appearance of a new ε-hcp grain oriented relative to the parent γ-fcc phase, was taken as evidence of grain-specific stress required to trigger phase transformation. The highest resolved shear stress on the potential transformation systems was identified as the critical resolved shear stress (CRSS) for strain-induced phase transformation. For the studied metastable alloy, CRSS for transformation was determined to be 86±3 MPa which was very close to theoretical CRSS value determined using Schmid factor (89±12 MPa) compared to the value determined using Taylor factor (62±7 MPa).

Jain, Roopam↗
DOE OSTI2023

Mapping the Complete Reaction Energy Landscape of a Metal–Organic Framework Phase Transformation

Crystalline materials undergo valuable phase transformations, and the energetic processes that underlie these transformations can be fully characterized through a combination of thermodynamic and kinetic studies. Here, we report the first complete reaction energy landscape of metal–organic framework (MOF) interpenetration, specifically in the phase transformation of NU-1200 to its doubly interpenetrated counterpart, STA-26. We characterized the thermodynamics of this phase transformation by pairing experiments with density functional theory (DFT) calculations. This analysis revealed that factors such as the increase in crystal density likely drive Zr- and Hf-NU-1200 to STA-26 interpenetration, while other chemical interactions such as steric repulsions prevent Th-NU-1200 from interpenetrating. Using time-resolved in situ X-ray diffraction, we monitored phase transformation reaction profiles and extracted quantitative kinetic information using the Avrami-Erofe’ev model. As a result, we obtained activation energies for the Zr- and Hf-NU-1200 transformations to Zr- and Hf-STA-26, respectively, revealing slower phase change kinetics for MOFs with stronger bonds. Finally, we paired the kinetic data with experimental observations to classify the mechanistic model of this phase transformation as partial dissolution. Here, we anticipate that this thermodynamic, kinetic, and mechanistic understanding will broadly inform further studies on the energetics of crystallization.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Size Transformation of the Au 22 (SG) 18 Nanocluster and Its Surface-Sensitive Kinetics

For many applications of well-defined gold nanoclusters, it is desirable to understand their structural evolution behavior under working conditions with molecular precision. Here we report the first systematic investigation of the size transformation products of the Au 22 (SG) 18 nanocluster under representative working conditions and highlight the surface effect on the transformation kinetics. Under thermal and aerobic conditions, the consecutive and pH-dependent transformation from Au 22 to both well-defined clusters and small Au(I)SR species was identified by ESI-MS and UV-vis spectroscopy. By introducing a perturbation onto the Au 22 surface, significant changes in the activation parameters were determined from the kinetic study of the Au 22 transformation. This indicates the sensitivity of the nanocluster transformation pathway to the cluster surface. Finally, the systematic study of cluster transformation and the sensitivity of cluster transformation to the surface revealed herein has significant implications for future attempts to design gold nanoparticles with adaptation to the working environment and the regeneration of active nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Local chemical fluctuation mediated ultra-sluggish martensitic transformation in high-entropy intermetallics

Superelasticity associated with martensitic transformation has found a broad range of engineering applications, such as in low-temperature devices in the aerospace industry. Nevertheless, the narrow working temperature range and strong temperature sensitivity of the first-order phase transformation significantly hinder the usage of smart metallic components in many critical areas. Here, we scrutinized the phase transformation behavior and mechanical properties of multicomponent B2-structured intermetallic compounds. Strikingly, the (TiZrHfCuNi) 83.3 Co 16.7 high-entropy intermetallics (HEIs) show superelasticity with high critical stress over 500 MPa, high fracture strength of over 2700 MPa, and small temperature sensitivity in a wide range of temperatures over 220 K. The complex sublattice occupation in these HEIs facilitates formation of nano-scaled local chemical fluctuation and then elastic confinement, which leads to an ultra-sluggish martensitic transformation. The thermal activation of the martensitic transformation was fully suppressed while the stress activation is severely retarded with an enhanced threshold stress over a wide temperature range. Moreover, the high configurational entropy also results in a small entropy change during phase transformation, consequently giving rise to the low temperature sensitivity of the superelasticity stress. Furthermore, our findings may provide a new paradigm for the development of advanced superelastic alloys, and shed new insights into understanding of martensitic transformation in general.

36 MATERIALS SCIENCE↗
DOE OSTI2020

No evidence for transient transformation via pollen magnetofection in several monocot species

The development of rapid and efficient transformation methods for many plant species remains an obstacle in both the basic and applied plant sciences. A novel method described by Zhao et al. (2017) used magnetic nanoparticles to deliver DNA into pollen grains of several dicot species, and one monocot (lily), to achieve transformation (“pollen magnetofection”). Using the published protocol, extensive trials by two independent research groups showed no indication of transient transformation success with pollen from two monocots, maize and sorghum. To further address the feasibility of magnetofection, lily pollen was used for side-by-side trials of magnetofection with a proven methodology for transient transformation, biolistics. Using a Green Fluorescent Protein reporter plasmid, transformation efficiency with the biolistic approach averaged 0.7% over three trials. However, the same plasmid produced no recognizable transformants via magnetofection, despite screening >3500 individual pollen grains. We conclude that pollen magnetofection is not effective for transient transformation of pollen for at least three species of monocots, and suggest that efforts to replicate the magnetofection protocol in dicot species would be useful to fully assess its potential. ARISING FROM Zhao et al. Nature Plants https://doi.org/10.1038/s41477-017-0063-z (2017)

Vejlupkova, Zuzana↗