Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “titanium alloys”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Grain reorientation and stress-state evolution during cyclic loading of an α -Ti alloy below the elastic limit

Here, high-energy synchrotron x-rays are used to track grain-averaged lattice reorientation and stress-state evolution in Ti–7Al as it is cyclically loaded to 90% of its macroscopic yield stress. This evolution provides clear indication of accumulating plastic strain even though the sample never exceeded the elastic limit. The largest changes in lattice orientation and stress state are observed following the first cycle then evolution continues at a lower rate with subsequent cycles. Variation of the axes about which lattice reorientation occurs is found to be highly dependent on the maximum resolved shear stress and corresponding activation of various families of slip systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A complete grain-level assessment of the stress-strain evolution and associated deformation response in polycrystalline alloys

Polycrystalline alloys are used pervasively across structural applications contingent upon extensive experimental testing. A statistically representative number of tests are required to expose the variability in the material's performance, as a result of non-uniform microstructures and associated micromechanical fields. In a more direct means of capturing this pertinent information, multi-modal experimental techniques are presented to measure and track the complete micromechanical state, evolving during loading, of each and every grain within the regions of interest. Specifically, a combination of high-energy X-ray diffraction microscopy and digital image correlation coupled with electron backscatter diffraction are conducted on a specimen for each of the alloys, Haynes 282 and Ti7Al. The results of the multi-modal analysis definitively demonstrate that the degree of heterogeneity increases with deformation level and is used to assess the number of grains necessary for a representative volume element description of the stress state for each of these materials. Moreover, higher resolution imaging is used for identification of the slip system activity and subsequently used to study slip transmission events. An accurate knowledge of the resolved shear stress in adjacent grains (grain interactions) is demonstrated to be a key descriptor of the slip transmission events.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Determination of α lamellae orientation in a β-Ti alloy using electron backscatter diffraction

The spatial orientation of α lamellae in a metastable β-Ti matrix of Timetal LCB (Ti–6.8 Mo–4.5 Fe–1.5 Al in wt%) was examined and the orientation of the hexagonal close-packed α lattice in the α lamella was determined. For this purpose, a combination of methods of small-angle X-ray scattering, scanning electron microscopy and electron backscatter diffraction was used. The habit planes of α laths are close to {111} β , which corresponds to (1$\bar3$20) α in the hexagonal coordinate system of the α phase. The longest α lamella direction lies approximately along one of the $\langle$110$\rangle$ β directions which are parallel to the specific habit plane. Taking into account the average lattice parameters of the β and α phases in aged conditions in Timetal LCB, it was possible to index all main axes and faces of an α lath not only in the cubic coordinate system of the parent β phase but also in the hexagonal system of the α phase.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-Situ Calibrated Digital Process Twin Models for Resource Efficient Manufacturing

The chief objective of manufacturing process improvement efforts is to significantly minimize process resources such as time, cost, waste, and consumed energy while improving product quality and process productivity. This paper presents a novel physics-informed optimization approach based on artificial intelligence (AI) to generate digital process twins (DPTs). The utility of the DPT approach is demonstrated in the case of finish machining of aerospace components made from gamma titanium aluminide alloy (γ-TiAl). This particular component has been plagued with persistent quality defects, including surface and sub-surface cracks, which adversely affect resource efficiency. Previous process improvement efforts have been restricted to anecdotal post-mortem investigation and empirical modeling, which fail to address the fundamental issue of how and when cracks occur during cutting. In this work, the integration of in-situ process characterization with modular physics-based models is presented, and machine learning algorithms are used to create a DPT capable of reducing environmental and energy impacts while significantly increasing yield and profitability. Based on the preliminary results presented here, we report an improvement in the overall embodied energy efficiency of over 84%, 93% in process queuing time, 2% in scrap cost, and 93% in queuing cost has been realized for γ-TiAl machining using our novel approach.

42 ENGINEERING↗
DOE OSTI2021

Mechanical Behavior Assessment of Ti-6Al-4V ELI Alloy Produced by Laser Powder Bed Fusion

The present work correlates the quasi-static, tensile mechanical properties of additively manufactured Ti-6Al-4V extra low interstitial (ELI, Grade 23) alloy to the phase constituents, microstructure, and fracture surface characteristics that changed with post-heat treatment of stress relief (670 °C for 5 h) and hot isostatic pressing (HIP with 100 MPa at 920 °C for 2 h under an Ar atmosphere). Ti-6Al-4V ELI alloy tensile specimens in both the horizontal (i.e., X and Y) and vertical (Z) directions were produced by the laser powder bed fusion (LPBF) technique. Higher yield strength (1141 MPa), higher tensile strength (1190 MPa), but lower elongation at fracture (6.9%), along with mechanical anisotropy were observed for as-stress-relieved (ASR) samples. However, after HIP, consistent and isotropic mechanical behaviors were observed with a slight reduction in yield strength (928 MPa) and tensile strength (1003 MPa), but with a significant improvement in elongation at fracture (16.1%). Phase constituents of acicular α' phase in ASR and lamellar α + β phases in HIP samples were observed and quantified to corroborate the reduction in strength and increase in ductility. The anisotropic variation in elongation at fracture observed for the ASR samples, particularly built in the build (Z) direction, was related to the presence of “keyhole” porosity.

42 ENGINEERING↗
DOE OSTI2021

Mechanisms of Ti 3 Al precipitation in hcp α -Ti

Here, nucleation and growth of Ti3Al α( 2 ) ordered domains in alpha-Ti-Al-X alloys were characterised using a combination of transmission electron microscopy, atom probe tomography and small angle X-ray scattering. Model alloys based on Ti-7Al (wt.%) and containing O, V and Mo were aged at 550 °C for times up to 120d and the resulting precipitate dispersions were observed at intermediate points. Precipitates grew to around 30nm in size, with a volume fraction of 6-10% depending on tertiary solutes. Interstitial O was found to increase the equilibrium volume fraction of α 2 , while V and Mo showed relatively little influence. Addition of any of the solutes in this study, but most prominently Mo, was found to increase nucleation density and decrease precipitate size and possibly coarsening rate. Coarsening can be described by the Lifshitz-Slyozov-Wagner model, suggesting a matrix diffusion-controlled coarsening mechanism (rather than control by interfacial coherency). Solutionising temperature was found to affect nucleation number density with an activation energy of E f = 1.5 +/- 0.4 eV, supporting the hypothesis that vacancy concentration affects α 2 nucleation. The observation that all solutes increase nucleation number density is also consistent with a vacancy-controlled nucleation mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Interplay of strain and phase evolution of laser powder bed fusion Ti–6Al–4V

While additive manufacturing (AM) provides a method of producing geometrically complex and highly detailed structures, the generation of residual strain in AM processes like laser powder bed fusion (L-PBF) can negatively impact performance-enabling properties. In applications such as orthopedic implants, specific performance windows require optimized microstructures in order to obtain desirable properties from multi-phase alloys like Ti–6Al–4V. This research aims to quantify the microscale origins of strain in L-PBF manufactured Ti–6Al–4V by understanding how strain is distributed at the grain and sub-grain scale, the interplay between phase evolution and strain, and examining post-processing strain relief strategies to control these features. Model spinal cage implants were manufactured from Ti–6Al–4V powder via L-PBF and then subjected to strain relieving heat treatment cycles above and below the Ti–6Al–4V β transus as a function of time and cooling rate. Residual strain was then studied via high resolution electron backscatter diffraction (HR-EBSD), and 2D strain maps with sub-micron resolution were generated for each post-processing state. It was found that macroscale thermal strains decreased with heat treatment time, but additional contributions from phase stabilizing residual strains retained primarily in the α' grains as lattice distortive strain remained. Additionally, the retention of β phase significantly changed the strain and dislocation distribution while reducing overall residual strain. In conclusion, these results were validated and reinforced with 3D mesoscopic micromechanical modeling of strain behavior across simulated microstructures, confirming that the local lattice dilation of α’ martensite is a primary contributor of microscale strain generation and retention in L-PBF Ti–6Al–4V.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microscale drivers and mechanisms of fracture in post-processed additively manufactured Ti–6Al– 4 V

Herein, we focus on understanding the microstructure-fracture correlations in a Ti–6Al– 4 V alloy additively manufactured via electron beam melting (EBM) and subjected to various post-process heat-treatments. Specifically, the as fabricated material is subjected to a sub-transus heat-treatment followed by air-cooling and a super-transus heat-treatment followed by either air- or furnace-cooling. Next, a series of in-situ single edge notch tension (SENT) tests are carried out under a high-resolution digital optical microscope. The panoramic high-resolution images captured during the in-situ tests are then used to characterize the planar deformation on the specimen surface using microstructure-based digital image correlation (DIC). Additionally, the results of the in-situ SENT tests together with DIC and post-mortem fractographic analyses provided us with a better understanding of the microstructure-fracture correlations in these materials. Our results show that the fracture mechanism of the as fabricated and sub-transus heat-treated materials is essentially the same, while the changes in the microstructure following the super-transus heat-treatments significantly affects the fracture mechanism. In this case, several microcracks of hundreds of microns in length first nucleate away from the deformed notch following extreme plastic deformation at discrete locations. Furthermore, the location of these microcracks in the super-transus heat-treated materials is extremely sensitive to the details of the underlying microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding Oxide–Metal Interactions During Hot Isostatic Pressing to Diffusion Bond Aluminum Alloy 6061 Plates

The interaction between Mg, Si, and Al 2 O 3 during hot isostatic pressing diffusion bonding of aluminum alloy 6061 (AA6061) plates was investigated through thermodynamic calculations and experimental microstructural characterization. Thermodynamic calculations as functions of temperature, pressure, and composition revealed that the interaction among Mg, Si, and Al 2 O 3 yields Mg 2 Si and either MgO + Al or MgAl 2 O 4 + Al, facilitating the reduction of Al 2 O 3 and allowing Al/Al metallic bonds to form. Total pressure variation had a negligible influence on the oxygen partial pressure, and consequently, the reaction product formation. Oxygen partial pressure variation as a function of temperature and initial amount of Al 2 O 3 determined the formation of either MgO or MgAl 2 O 4 . Experimental Hot Isostatic Pressure (HIP) bonding at 723 K and 833 K under a constant pressure of 1017 atm documented the cooling rate-dependent formation of β–Mg 2 Si precipitates. High-resolution transmission electron microscopy imaging and selected area electron diffraction patterns verified the formation of β–Mg 2 Si and MgO at the interface but did not detect MgAl 2 O 4 . In conclusion, findings from this study clarify the role of thermochemical interactions in oxide disruption and bonding mechanisms during HIP diffusion bonding of AA6061 and provide guidance for optimizing joining processes for monolithic nuclear fuel assemblies.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Corrosion evaluation of Ti–6Al–4V manufactured by electron beam melting in Ringer’s physiological solution: an in vitro study of the passive film

We report that electrochemical characteristics and semiconducting behavior of additively manufactured electron beam melted (EBM) and wrought (WR) Ti–6Al–4V (Ti-G5) are compared in Ringer’s physiological solution. X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM) confirmed the α+β structure of the tested materials, with two different microstructure types of “bimodal” and “basket-weave” for WR and EBM, respectively. Potentiodynamic polarization (PDP) revealed that the corrosion current density for EBM (i corr =0.27±0.06 μA cm -2 ) is less than the WR (i corr =0.70±0.05 μA cm -2 ). Moreover, potentiostatic polarization (PS) that was employed to form the passive layers at three different potentials of 300, 500, and 700 mV Ag/AgCl , showed that the passive films on the EBM sample are thinner. This finding was confirmed by electrochemical impedance spectroscopy (EIS). Furthermore, through Mott–Schottky (M–S) analysis, donor densities on WR passive films were found to be ~1.5 times larger than EBM. Although PS and EIS confirmed that the passive layer on EBM is thinner, it provides higher corrosion resistance than WR. The passive layer on both samples were found to have n-type characteristics with a duplex structure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Determining anisotropic slip system rate sensitivities of Ti-6Al-4V using high-energy X-ray diffraction microscopy

Variation of strain rate sensitivity among different families of slip systems in the hexagonal close-packed (α) phase of titanium (Ti) alloys has the potential to alter microscale load redistribution during both creep and dwell fatigue loading. However, existing literature contains conflicting reports regarding the degree of anisotropy present in the strain rate sensitives between α slip system families across Ti alloys. Here, we quantify the strain rate sensitivity of α slip system families in Ti-6Al-4V using high-energy X-ray diffraction microscopy (HEDM). We present a novel procedure in which we utilize the HEDM-measured grain-scale stress states during stress relaxation to determine the strain rate sensitivities of the basal $\langle a \rangle$ , prismatic $\langle a \rangle$, and first-order pyramidal $\langle c + a \rangle$ slip system families. In addition, we measure the strain rate sensitivity exponent of the macroscopic response and the α phase for comparison. We find rate sensitivities for the different slip system families to range from 0.02 to 0.04, which—while varied—are relatively isotropic in comparison with some values presented in the literature. We also demonstrate the effects of the measured anisotropic rate sensitivities using crystal plasticity finite element simulations.

Peterson, Kenneth M. [Pennsylvania State Univ., Un↗
DOE OSTI2023

Hydrogen-Aided Microstructural Engineering of Additively Manufactured Ti–6Al–4V

Electron beam melting (EBM) additive manufacturing of Ti–6Al–4V subjects the material to complex thermal cycles, resulting in a columnar morphology of the prior β grains (PBGs). While the columnar PBGs of EBM-processed Ti–6Al–4V can be transformed to an equiaxed morphology through a super-transus (i.e., above the β -transus temperature) heat treatment, this also leads to the formation of a coarse lamellar two-phase microstructure. Such a microstructure is prone to strain localization and premature fracture. In this study, we present a thermohydrogen post-process treatment that achieves equiaxed PBG morphology in EBM-processed Ti–6Al–4V without sacrificing mechanical properties. Our results show that a three-step thermohydrogen post-process treatment can transform the columnar PBG morphology to an equiaxed morphology with fine microstructure, and strength and ductility levels comparable to those of the most optimum as-fabricated samples. This three-step thermohydrogen post-process treatment involves hydrogenation and phase transformation treatment in a hydrogen atmosphere, and subsequent dehydrogenation treatment in vacuum. Notably, all these treatments are carried out at temperatures well below the β -transus temperature of hydrogen-free Ti–6Al–4V.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Grain-resolved temperature-dependent anisotropy in hexagonal Ti-7Al revealed by synchrotron X-ray diffraction

Hexagonal metals have anisotropic coefficients of thermal expansion causing grain-level internal stresses during heating. High energy x-ray diffraction microscopy, a non-destructive, in situ, micromechanical and microstructural characterization technique, has been used to determine the anisotropic coefficients of thermal expansion (CTEs) for Ti-7Al. Two samples of polycrystalline α-phase Ti-7Al were continuously heated from room temperature to 850 °C while far-field HEDM scans were collected. The results showed a change in the ratio of the CTEs in the ‘a’ and ‘c’ directions which explains discrepancies found in the literature. The CTE additionally appears to be affected by the dissolution of α 2 precipitates. Analysis of the grain-resolved micromechanical data also shows reconfiguration of the grain scale stresses likely due to anisotropic expansion driving crystallographic slip.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Clarifying the formation of equiaxed grains and microstructural refinement in the additive manufacturing of Ti-Cu

Controlling microstructural evolution in metallic additive manufacturing (AM) is difficult, especially in producing refined as-built grains instead of coarse, directional grains. Traditional solutions involve adding inoculants to AM feedstocks, but titanium (Ti) alloys cannot employ this approach without producing detrimental secondary phases. Ti-Cu (Ti-copper) alloys offer a solution through constitutional supercooling and/or solid state thermal cycling under AM conditions. This work analyzes a compositionally graded directed energy deposition (DED) Ti-Cu build, single-melt laser tracks, and dilatometric heat treatments to evaluate if, when, and by what mechanism(s) microstructural refinement occurs. Refinement by inoculation of unmelted powder particles was also considered. Constitutional supercooling produced no net microstructural refinement as any equiaxed dendrites which form are remelted with new deposition. This finding agreed with solidification modeling of powder bed fusion-laser beam (PBF-LB) and DED builds. Solid state thermal cycling refined microstructures only during ex-situ dilatometric heat treatments, suggesting build parameter optimization is needed to achieve refinement in-situ. Accidental heterogeneous nucleation on unmelted Ti powder, originating from the different thermophysical properties of Ti and Cu, provided the most significant microstructural refinement. This work systematically assesses the microstructural refinement mechanisms of Ti-Cu in AM builds and offers insights into microstructural control in eutectoid alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Implications of post-processing induced microstructural changes on the deformation and fracture response of additively manufactured Ti–6Al–4V

Ti–6Al–4V parts fabricated via electron beam melting (EBM) powder bed fusion are often subjected to hot isostatic pressing below the β-transus temperature to mitigate defects. During which the pressure aids in pore closure and the thermal exposure results in coarsening of α phase while retaining the columnar prior-β phase grain morphology present in the as-fabricated condition. The same post-processing treatment can also be carried out above β-transus temperature which is an effective way to modify both the grain morphology and the associated α textures. Here, the objective of this work is to correlate thermally induced microstructural changes to the deformation and fracture response of the EBM processed Ti–6Al–4V. To this end, we have carried out both sub-transus and super-transus heat-treatments of the as-fabricated material. The mechanical response of the as-fabricated and all heat-treated materials are characterized by in-situ tensile tests under a high-resolution digital optical microscope. This enabled us to capture large-scale panoramic images of the deforming microstructure, and overcome the trade-off between the image resolution and the field of view during in-situ experiments. The series of images captured throughout the imposed deformation are subsequently used to perform microstructure-based digital image correlation to measure microstructural-scale strains over a large area. The results of the in-situ tests together with detailed fractographic analyses are then used to elucidate how the heterogeneous deformation spanning over multiple microstructural length-scales, for example, at the scale of lamellae, colonies of lamellae and grain boundaries, affect the overall deformation and fracture response of the post-processed materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanistic basis of oxygen sensitivity in titanium

One of the most potent examples of interstitial solute strengthening in metal alloys is the extreme sensitivity of titanium to small amounts of oxygen. Unfortunately, these small amounts of oxygen also lead to a markedly decreased ductility, which in turn drives the increased cost to purify titanium to avoid this oxygen poisoning effect. Here, we report a systematic study on the oxygen sensitivity of titanium that provides a clear mechanistic view of how oxygen impurities affect the mechanical properties of titanium. The increased slip planarity of Ti-O alloys is caused by an interstitial shuffling mechanism, which is sensitive to temperature, strain rate, and oxygen content and leads to the subsequent alteration of deformation twinning behavior. The insights from our experimental and computational work provide a rationale for the design of titanium alloys with increased tolerance to variations in interstitial content, with notable implications for more widespread use of titanium alloys.

36 MATERIALS SCIENCE↗