Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermoplastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A thermoplastic polyimidesulfone

A polymer system has been prepared which has the excellent thermoplastic properties generally associated with polysulfones, and the solvent resistance and thermal stability of aromatic polyimides. This material, with improved processability over the base polyimide, can be processed in the 260-325 C range in such a manner as to yield high quality, tough unfilled moldings; strong, high-temperature-resistant adhesive bonds; and well consolidated, graphite-fiber-reinforced moldings (composites). The unfilled moldings have physical properties that are similar to aromatic polysulfones which demonstrates the potential as an engineering thermoplastic. The adhesive bonds exhibit excellent retention of initial strength levels even after thermal aging for 5000 hours at 232 C. The graphite-fiber-reinforced moldings have mechanical properties which makes this polymer attractive for the fabrication of structural composites.

St. Clair, T. L.↗
NASA NTRS1986

Effect of annealing history on free volume in thermoplastics

Two different types of thermoplastic glassy polymers have been investigated for the effects of thermal annealing on their free volumes. It has been observed that free volumes in glassy polymers decrease asymptotically to a steady level after about four thermal anneals lasting for 24 hours at a temperature about 50 C below their glass transition temperatures. These results indicate that composites incorporating properly annealed thermoplastic matrices may not experience any additional internal stresses due to subsequent thermal excursions experienced while in service.

Singh, J. J.↗
NASA NTRS1985

Process optimization of a thermoplastic polyimidesulphone

The detailed characterization of an experimental thermoplastic polyimidesulfane adhesive based on 3,3 prime-diaminodiphenylsulfone and 3,3 prime,4,4 prime-benzophenone tetracarboxylic dianhydride was studied. Model compounds were also examined. Thermal cyclization of the amide-acid to the imide was studied by a variety of techniques including DSC, TGA, MS, in situ diffuse reflectance-FTIR, and flow measurement. Characterizations were continued during the processing of adhesive tapes and the fabrication, bonding, and testing of lap shear specimens. Results provide fundamental insights into the role of cure chemistry, and the effects of residual solvent and volatile produces on processing and performance. These insights and the resulting chemical models should lead to more efficient processing cycles for these and other related thermoplastic adhesive systems.

Dezern, J. F.↗
NASA NTRS1987

Analyzing Nonisothermal Crystallization of Thermoplastics

Method developed for analysis of nonisothermal cold crystallization in thermoplastics. Does not require prior knowledge of isothermal kinetic parameters. Based upon observation: During nonisothermal crystallization at constant rate, relative crystallinity develops with time dependence sigmoidal at low degrees of conversion. Application for method is study of cold crystallization in advanced thermoplastics.

Cebe, Peggy↗
NASA NTRS1986

The crystallization of tough thermoplastic resins in the presence of carbon fibers

The crystallization kinetics of the thermoplastic resins poly(phenylene sulfide) (PPS) and poly(aryl-ether-ether-ketone) (PEEK) in the presence and in the abscence of carbon fibers was studied. How carbon fiber surfaces in composites affect the crystallization of tough thermoplastic polymers that may serve as matrix resins were determined. The crystallization kinetics of such substances can provide useful information about the crystallization mechanisms and, thus, indicate if the presence of carbon fibers cause any changes in such mechanisms.

Theil, M. H.↗
NASA NTRS1987

High performance thermoplastics: A review of neat resin and composite properties

A review was made of the principal thermoplastics used to fabricate high performance composites. Neat resin tensile and fracture toughness properties, glass transition temperatures (Tg), crystalline melt temperatures (Tm) and approximate processing conditions are presented. Mechanical properties of carbon fiber composites made from many of these thermoplastics are given, including flexural, longitudinal tensile, transverse tensile and in-plane shear properties as well as short beam shear and compressive strengths and interlaminar fracture toughness. Attractive features and problems involved in the use of thermo-plastics as matrices for high performance composites are discussed.

Johnston, Norman J.↗
NASA NTRS1988

Processable Aromatic Polyimide Thermoplastic Blends

Method developed for preparing readily-processable thermoplastic polyimides by blending linear, high-molecular-weight, polyimic acid solutions in ether solvents with ultrafine, semicrystalline, thermoplastic polyimide powders. Slurries formed used to make prepregs. Consolidation of prepregs into finsihed composites characterized by excellent melt flow during processing. Applied to film, fiber, fabric, metal, polymer, or composite surfaces. Used to make various stable slurries from which prepregs prepared.

Baucom, Robert M↗
NASA NTRS1987

High performance thermoplastics - A review of neat resin and composite properties

A review was made of the principal thermoplastics used to fabricate high performance composites. Neat resin tensile and fracture toughness properties, glass transition temperatures (Tg), crystalline melt temperatures (Tm) and approximate processing conditions are presented. Mechanical properties of carbon fiber composites made from many of these thermoplastics are given, including flexural, longitudinal tensile, transverse tensile and in-plane shear properties as well as short beam shear and compressive strengths and interlaminar fracture toughness.

Johnston, Norman J.↗
NASA NTRS1989

Thermoplastic coating of carbon fibers

A continuous powder coating system was developed for coating carbon fiber with LaRC-TPI (Langley Research Center-Thermoplastic Polyimide), a high-temperature thermoplastic polymide invented by NASA-Langley. The coating line developed used a pneumatic fiber spreader to separate the individual fibers. The polymer was applied within a recirculating powder coating chamber then melted using a combination of direct electrical resistance and convective heating to make it adhere to the fiber tow. The tension and speed of the line were controlled with a dancer arm and an electrically driven fiber wind-up and wind-off. The effects of heating during the coating process on the flexibility of the prepreg produced were investigated. The uniformity with which the fiber tow could be coated with polymer also was examined. Composite specimens were fabricated from the prepreg and tested to determine optimum process conditions. The study showed that a very uniform and flexible prepeg with up to 50 percent by volume polymer could be produced with this powder coating system. The coating line minimized powder loss and produced prepeg in lengths of up to 300 m. The fiber spreading was found to have a major effect on the coating uniformity and flexibility. Though test results showed low composite tensile strengths, analysis of fracture surfaces under scanning electron microscope indicated that fiber/matrix adhesion was adequate.

Edie, D. D.↗
NASA NTRS1988

Toughening of a thermoplastic matrix composite - Processing issues

The use of a rubber modified thermoplastic resin has been investigated as a method to improve the impact damage and the Mode I interlaminar fracture toughness of a unidirectional continuous carbon fiber composite. Test results show that the improvement in the fracture toughness is less than expected due to rubber particle agglomeration, poor fiber/matrix adhesion and the induced crystallization of the matrix. These restrictions must be eliminated in order to evaluate the maximum potential of a rubber toughened thermoplastic matrix on a composite's fracture toughness.

Parker, D. S.↗
NASA NTRS1988

Creep and creep-recovery of a thermoplastic resin and composite

The database on advanced thermoplastic composites, which is currently available to industry, contains little data on the creep and viscoelastic behavior. This behavior is nevertheless considered important, particularly for extended-service reliability in structural applications. The creep deformation of a specific thermoplastic resin and composite is reviewed. The problem to relate the data obtained on the resin to the data obtained on the composite is discussed.

Hiel, Clem↗
NASA NTRS1988

Pultrusion with thermoplastics for the fabrication of structures in space

The use of the pultrusion method to produce structures in space is proposed. This technique is based on transporting materials in coils or bundles and fabricating the structures in space. Two methods for thermoplastic impregnation of advanced composite are described. The properties of three pultruded thermoplastic matrix materials, polyphenylene sulfide, polyetherimide (PEI), and polyetheretherketone (PEEK) are discussed and evaluated. It is observed that the pultrusions containing PEI and PEEK reveal post-fabrication potential of lightweight, high strength advanced composites and this method of fabrication produces strength values comparable to those of conventional techniques. Earth-based and space-based planetary shelter models are developed and compared. It is noted that cargo storage volume is dependent on a combination of profiles, packaging, and manufacturing methods.

Wilson, Maywood L.↗
NASA NTRS1989

Pultrusion process development of a graphite reinforced polyetherimide thermoplastic composite

High performance thermoplastic polymers do not contain reactants and solvents able to react with a pultrusion die to yield polymerization; consolidation is therefore performed with a rigid or a boardy prepreg, and consolidation must occur with polymers whose viscosities are of the order of 1 million centipoises or more. Die temperatures are typically above 400 C, by comparison with the 150-200 C encountered in thermosets. A methodical approach is presented here for the development of a pultrusion process suitable for polyetherimide and other engineering thermoplastics, employing SEM, DSC, TGA, and ultrasonic C-scanning.

Wilson, Maywood L.↗
NASA NTRS1991

Tough, High-Performance, Thermoplastic Addition Polymers

Series of addition-type thermoplastics (ATT's) exhibit useful properties. Because of their addition curing and linear structure, ATT polymers have toughness, like thermoplastics, and easily processed, like thermosets. Work undertaken to develop chemical reaction forming stable aromatic rings in backbone of ATT polymer, combining high-temperature performance and thermo-oxidative stability with toughness and easy processibility, and minimizing or eliminating necessity for tradeoffs among properties often observed in conventional polymer syntheses.

Pater, Ruth H.↗
NASA NTRS1990

Supportability evaluation of thermoplastic and thermoset composites

Nearly 300 advanced composite components manufactured by Northrop Corporation are flying on U.S. Air Force and U.S. Navy supersonic aircraft as part of a three-year Air Force/Navy/Northrop supportability evaluation. Both thermoplastic and high-temperature thermoset composites were evaluated for their in-service performance on 48 USAF and Navy F-5E fighter and USAFT-38 trainer aircraft in the first large-scale, long-term maintenance evaluation of these advanced materials. Northrop manufactured four types of doors for the project-avionics bay access, oil fill, inlet duct inspection, and a main landing gear door. The doors are made of PEEK (polyetheretherketone) thermoplastic, which is tougher and potentially less expensive to manufacture than conventional composites; and 5250-3 BMI (bismaleimide) thermoset, which is manufactured like a conventional epoxy composite but can withstand higher service temperatures. Results obtained so far indicate that both the BMI and PEEK are durable with PEEK being somewhat better than BMI.

Chanani, G. R.↗
NASA NTRS1991

Characterization of elastic-viscoplastic properties of an AS4/PEEK thermoplastic composite

The elastic-viscoplastic properties of an AS4/PEEK (APC-2) thermoplastic composite were characterized at 24 C (75 F) and 121 C (250 F) by using a one-parameter viscoplasticity model. To determine the strain-rate effects, uniaxial tension tests were performed on unidirectional off-axis coupon specimens with different monotonic strain rates. A modified Bodner and Partom's model was also used to describe the viscoplasticity of the thermoplastic composite. The experimental results showed that viscoplastic behavior can be characterized quite well using the one-parameter overstress viscoplasticity model.

Yoon, K. J.↗
NASA NTRS1991

Design and manufacturing concepts for thermoplastic structures

Results to date on the application of two manufacturing techniques, fiber placement and single diaphragm/coconsolidation, to produce cost-effective, thermoplastic composite (TPC), primary fuselage structure are presented. Applications relative to fuselage upper cover structure indicate potential cost savings relative to conventional approaches. Progress is also presented on efforts concerned with other design details which take advantage of thermoplastic composites such as fastener less stiffener/frame attachments. In addition, results are presented on the development and verification testing of a composite lug analysis program which incorporates through-the-thickness effects.

Renieri, Michael P.↗