SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The performance of a gigabit pulse-code modulation fiber system has been investigated as a function of laser temperature. The bit error rate shows an improvement for temperature in the range of -15 C to -35 C. A tradeoff seems possible between relaxation oscillation, rise time, and signal-to-noise ratio.
The objective of the research is to expand the experimental study of the effect of strain rate on mechanical response (deformation and failure) of epoxy resins and carbon fibers/epoxy matrix composites, to include elevated temperature tests. The experimental data provide the information needed for NASA scientists for the development of a nonlinear, strain rate and temperature dependent deformation and strength models for composites that can subsequently be used in design. This year effort was directed into the development and testing of the epoxy resin at elevated temperatures. Two types of epoxy resins were tested in shear at high strain rates of about 700 per second and elevated temperatures of 50 and 80 C. The results show that the temperature significantly affects the response of epoxy.
This paper gives an overview of our current understanding of thermal phenomena in elastohydrodynamic contacts and suggests some avenues for fruitful research in the next decade. Typical measured temperatures are presented for representative conditions and ranges of operating parameters. Temperatures can range from bulk ambient temperature to several hundred degrees centigrade in fully separated elastohydrodynamic films. Although attention in the past decade has been on the full film for the purposes of understanding film thickness and traction phenomena, the more interesting conditions are in the mixed elastohydrodynamic films. These mixed conditions are both common in tribological systems and they are the conditions that border on unsuccessful run-in and failure of the elastohydrodynamic contact. In mixed film conditions local hotspots can have temperatures of the order of 1888 C which cause increased reactivity of the surfaces with surrounding materials as well as changes of the surface physical properties so important to the operation of concentrated contacts. An additional area discussed is that of the bulk system thermal transients which occur in tribological systems. These transients are frequently long in duration and have a direct bearing on the elastohydrodynamic film thickness and traction.
A time-dependent characterization study was performed on T300/934 graphite/epoxy in a simulated space environment. Creep tests on irradiated and nonirradiated graphite/epoxy and bulk resin specimens were carried out at temperatures of 72 and 250 F. Irradiated specimens were exposed to dosages of penetrating electron radiation equal to 30 years exposure at GEO-synchronous orbit. Radiation was shown to have little effect on the creep response of both the composite and bulk resin specimens at 72 F while radiation had a significant effect at 250 F. A healing process was shown to be present in the irradiated specimens where broken bonds in the epoxy due to radiation recombined over time to form cross-links in the 934 resin structure. An analytical micromechanical model was also developed to predict the viscoelastic response of fiber reinforced composite materials. The model was shown to correlate well with experimental results for linearly viscoelastic materials with relatively small creep strains.
An investigation was conducted at the National Transonic Facility (NTF) to document the change in sting-balance deflections from ambient to cryogenic temperatures. Space limitations in some NTF models do not allow the use of on-board angle of attack instrumentation. In order to obtain angle of attack data, pre-determined sting-balance bending data must be combined with arc sector angle measurements. Presently, obtaining pretest sting-balance data requires several cryogenic cycles and cold loadings over a period of several days. A method of reducing the calibration time required is to obtain only ambient temperature sting-balance bending data and correct for changes in material properties at cryogenic temperatures. To validate this method, two typical NTF sting-balance combinations were tested. The test results show excellent agreement with the predicted values and the repeatability of the data was 0.01 degree.
1. Neural activity was recorded in hippocampal slices from euthermic chipmunks, hamsters and rats. 2. While recording the evoked potentials, the temperature of the Ringer's solution bathing the slice was varied by controlling the temperature of an outer chamber jacketing the recording chamber. 3. The temperature just below that at which a population spike could be evoked, Tt, was 10.4 +/- 0.3 degrees C (mean +/- SEM) for chipmunk slices, 14.1 +/- 0.4 degrees C for rat slices and 14.8 +/- 0.4 degrees C for hamster slices. Tt was significantly lower in the chipmunk slices (P<0.01) than in the rat and hamster slices. 4. Data were interpreted as consistent with the hypothesis that chipmunk hippocampal neurons are intrinsically cold resistant.
UC1-xNx fuel kernels provided by Oak Ridge National Laboratory (ORNL) were irradiated by 84 MeV Xe ions at two different temperatures (450°C & 750°C) at the Argonne Tandem Linac Accelerator System (ATLAS) at Argonne National Laboratory, followed by post-irradiation examination. The primary goal of this study was to understand gas bubble formation (due to accumulation of Xe gas) and corresponding size evolution dependent upon net Xe deposition at the two different temperatures. From the post-irradiation examinations of the samples, it can be concluded at 750°C, with same amount of dose received, the Xe gas bubbles seems to coarsen much more easily compared to 450°C. The results generated for fission gas bubble evolution observed in this study can be used to support fuel performance models for UC1-xNx fuel kernels.
A unidirectional graphite epoxy material (AS4/3501-6) was characterized at strain rates ranging from 5 x 10(exp 6) s(exp -1) to 5(exp -1), at room temperature and at 128 C. Results are presented in the form of stress-strain curves to failure. The longitudinal properties remain nearly unchanged with strain rate and temperature. The transverse modulus increases with strain rate but decreases with temperature. The transverse strength and transverse ultimate tensile strain have a positive rate sensitivity at low rates, which changes to negative at intermediate rates and returns to positive rate sensitivity at the highest rates tested. A temperature-time equivalence principle was applied and master curves were obtained for the transverse mechanical properties. The in-plane shear modulus and in-plane shear strength have a positive rate sensitivity. The ultimate intralaminar shear strain has a positive rate sensitivity at low rates, which changes to negative at high rates. At the elevated temperature of 128 C, the ultimate shear strain is 25 to 30 percent higher than the room temperature value, but its strain rate dependence is moderate.
We have measured the amplitude of the 215 s pulsation of the pulsating DA white dwarf, or ZZ Ceti star, G117-B15A in six passbands with effective wavelengths from 1570 to 6730 A. We find that the index of the pulsation is l = 1 with a high degree of confidence, the first unambiguous determination of l for a pulsation of a ZZ Ceti star. We also find that log g and T(sub eff) are tightly correlated for model atmospheres that fit the data, such that at log g = 7.5 the temperature is 11,750 K and at log g = 8.0 the temperature is 12,375 K. Adopting log g = 7.97 +/- 0.06 from published observations of the optical spectrum of G117-B15A, the correlation yields T(sub eff) = 12,375 +/- 125 K. This temperature is free of flux calibration errors and should be substantially more reliable than temperatures derived for IUE spectra. Since G117-B15A is thought to lie close to the blue edge of the ZZ Ceti instability strip, this low temperature also implies a low temperature for the blue edge. Using pulsation models calculated by Fontaine et al. (1992) and Bradley (1994), we find that the mass of the hydrogen layer in G117-B15A lies between 1.0 x 10(exp -6) solar mass (for k = 1) and 8 x 10(exp -5) solar mass (for k = 2). This range of masses is (barely) consistent with the masses predicted by recent models for the ejection of planetary nebulae, (8-13) x 10(exp -5) solar mass. The mass is too large to be consistent with models invoking thin hydrogen layers to explain the spectral evolution of white dwarfs.
Results from post-irradiation examination (PIE) of U-10Mo binary metallic fuel irradiated by 84 MeV Xe ions at two different temperatures (450°C & 275°C) have been evaluated and reported. The main goal of this study was to understand gas bubble formation (due to accumulation of Xe gas) and corresponding size evolution dependent upon net Xe deposition at two different temperatures, for the U-10Mo fuel samples. From the post ion irradiation examination analysis, it can be concluded that at 450°C the Xe gas bubbles seems to coarsen more easily compared to 275°C. The results of ion irradiation testing can provide initial data that may be beneficial for fuel system down-selections, and for the development and validation of fuel performance models.
Degradation of low cobalt lithium-ion cathodes was tested using a full factorial combination of upper cut-off voltage (4.0 V and 4.3 V vs. Li/Li + ) and operating temperature (25 °C and 60 °C). Half-cell batteries were analyzed with electrochemical and microstructural characterization methods. Electrochemical performance was assessed with galvanostatic cycling, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) supported by distribution of relaxation times (DRT) analysis. Electrode microstructure was characterized with scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray absorption near edge structure (XANES) imaging. Higher cut-off voltage cycling shows presence of NiO x formation, a low diffusivity rock-salt phase, in both CV and XRD data. XRD patterns confirmed that the rock-salt phase was beginning to form at the low cut-off voltage at high temperature, but in much lower intensity than at the high cut-off voltage. Higher temperature accelerates degradation processes at both voltages. Degradation factors at high temperature include NiO x formation, cathode material dissolution, and electrolyte decomposition. SEM analysis suggests that supporting phases may isolate and disconnect active material particles reducing capacity retention and battery life cycle. DRT analysis and XANES imaging show that both high temperature samples revealed a NiO x phase based on an increased diffusive impedance and a visible shift in the XANES spectra. The low cut-off voltage, high temperature sample showed a split peak and shift to lower energies indicating early formation of the NiO x phase. The diffusive impedance, which hinders intercalation and deintercalation, is driven by the formation of the NiO x phase. While primarily driven by cut-off voltage, elevated temperature also contributes to this degradation mechanism.
This study examined the clustering behavior of monohydroxy alcohols, where hydrogen-bonded clusters of up to a hundred molecules on the nanoscale can form. By performing X-ray diffraction experiments at different temperatures and under high pressure, we investigated how these conditions affect the ability of alcohols to form clusters. The pioneering high-pressure experiment performed on liquid alcohols contributes to the emerging knowledge in this field. Implementation of molecular dynamics simulations yielded excellent agreement with the experimental results, enabling the analysis of theoretical models. Here we show that at the same global density achieved either by alteration of pressure or temperature, the local aggregation of molecules at the nanoscale may significantly differ. Surprisingly, high pressure not only promotes the formation of hydrogen-bonded clusters but also induces the serious reorganization of molecules. This research represents a milestone in understanding association under extreme thermodynamic conditions in other hydrogen bonding systems such as water.
Recently it has been argued based on theoretical calculations and experimental data that there is a universal form for the equation of state of solids. This observation was restricted to the range of temperatures and pressures such that there are no phase transitions. The use of this universal relation to estimate pressure-volume relations (i.e., isotherms) required three input parameters at each fixed temperature. It is shown that for many solids the input data needed to predict high temperature thermodynamical properties can be dramatically reduced. In particular, only four numbers are needed: (1) the zero pressure (P=0) isothermal bulk modulus; (2)it P=0 pressure derivative; (3) the P=0 volume; and (4) the P=0 thermal expansion; all evaluated at a single (reference) temperature. Explicit predictions are made for the high temperature isotherms, the thermal expansion as a function of temperature, and the temperature variation of the isothermal bulk modulus and its pressure derivative. These predictions are tested using experimental data for three representative solids: gold, sodium chloride, and xenon. Good agreement between theory and experiment is found.
Recently it has been argued based on theoretical calculations and experimental data that there is a universal form for the equation of state of solids. This observation was restricted to the range of temperatures and pressures such that there are no phase transitions. The use of this universal relation to estimate pressure-volume relations (i.e., isotherms) required three input parameters at each fixed temperature. It is shown that for many solids the input data needed to predict high temperature thermodynamical properties can be dramatically reduced. In particular, only four numbers are needed: (1) the zero pressure (P = 0) isothermal bulk modulus; (2) its P = 0 pressure derivative; (3) the P = 0 volume; and (4) the P = 0 thermal expansion; all evaluated at a single (reference) temperature. Explicit predictions are made for the high temperature isotherms, the thermal expansion as a function of temperature, and the temperature variation of the isothermal bulk modulus and its pressure derivative. These predictions are tested using experimental data for three representative solids: gold, sodium chloride, and xenon. Good agreement between theory and experiment is found.
Post-irradiation examination (PIE) results of microstructure in irradiated Al-UMo diffusion couples are reported here. These diffusion couples were irradiated by 60 MeV Xe ions at four different temperatures up to approximately 5.5 × 10 17 ions/cm 2 peak ion fluence. An Al-UMo interaction layer (IL) was found to form at all four investigated temperatures. The IL is homogeneously amorphous when formed up to 150 °C. At 215 °C, the (U,Mo)Al 3 nanocrystalline precipitates form within the amorphous IL matrix. Kirkendall voids with prominent temperature dependence were observed in both the Al layer and its interface with the IL. On the other hand, Xe bubbles were found to form in UMo and Al-UMo IL with different morphology. These microstructure features were quantitatively measured and are reported to provide valuable references for understanding the irradiation behavior of UMo/Al dispersion fuel.
Gaussian band-fitting analysis has been applied to the reflectance spectra of mafic silicates, which are of geologic importance throughout much of the solar system. Reflectance spectra obtained over a sample temperature range of about 80 to 448 K of olivine, clinopyroxene, and orthopyroxene were used in order to characterize the spectral changes in the 1-micron wavelength region of these minerals as a function of temperature. Four Gaussians are required to characterize the olivine, while two Gaussians are necessary to characterize both the orthopyroxene. The trends of the individual Gaussian parameters (integrated area, width, and center position) are presented as a function of temperature for each mineral. The characterization by Gaussian analysis of the 1-micron absorption feature of all minerals yields consistent trends in center position, integrated area, and width that may prove useful in quantitative determination of these minerals in mineral mixtures.
Bulk-sputtered OFHC Cu and Cu-0.15 Zr used as inner walls of advanced regeneratively cooled thrust chambers are evaluated as to microstructure, surface topography, and fractography. It is found that under conditions of low substrate temperature, crystallite size and openness of the structure increase with increasing deposition rate for both materials. At elevated temperatures, an equiaxed ductile structure of OFHC Cu is produced only at low deposition rates; at higher deposition rate, open structures are observed with recrystallized equiaxed grains within large poorly bonded crystallites. The Cu-0.15 Zr alloy sputtered from the hollow cathode using a diode discharge shows open-type structures for all conditions evaluated. The use of a triode discharge in generating a dense non-voided structure of Cu-0.15 Zr is discussed.
This paper will concentrate on results obtained from the Jet Propulsion Lab (JPL) Fiber Optics Long Duration Exposure Facility (LDEF) Experiment since the June 1991 Experimenters Workshop. Radiation darkening of the laboratory control samples will be compared with the LDEF flight samples. The results of laboratory temperature tests on the flight samples extending over a period of about nine years including the preflight and postflight analysis periods will be described.