Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface roughness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

An experimental investigation of silicon wafer surface roughness and its effect on the pull-strength of plated metals

Plated silicon wafers with surface roughness ranging from 0.4 to 130 microinches, subjected to tensile pull-strength tests, were analyzed. Results show that the measured pull-strength of plated metals decrease with increasing silicon surface roughness, effecting a weakening of the cohesive strength of the wafer, possibly caused by microcracks or 'etch pits' in the silicon surface. The mean value of pull-strength for all wafers plated with the Ni-Cu-Cu sequence exceeded the required 450 g/0.02 sq cm, and at Ra = 0.4 microinches, the mean pull-strength for the Ni-Cu-Cu and Ni-Cu wafers were 2290 and 850 g/0.02 sq cm, respectively. The development of standardized methods for measuring contact pull-strength is suggested. These results may have some bearing on solar cell arrays problems.

Spiers, G. D.↗
NASA NTRS1981

An experimental investigation of silicon wafer surface roughness and its effect on the full strength of plated metals

Plated silicon wafers with surface roughness ranging from 0.4 to 130 microinches were subjected to tensile pull strength tests. Electroless Ni/electroless Cu/electroplated Cu and electroless Ni/electroplated Cu were the two types of plate contacts tested. It was found that smoother surfaces had higher pull strength than rougher, chemically etched surfaces. The presence of the electroless Cu layer was found to be important to adhesion. The mode of fracture of the contact as it left the silicon was studied, and it was found that in almost all cases separation was due to fracture of the bulk silicon phase. The correlation between surface roughness and mode of contact failure is presented and interpreted.

Spiers, G. D.↗
NASA NTRS1984

Analysis and testing for rotordynamic coefficients of turbulent annular seals with different, directionally-homogeneous surface-roughness treatment for rotor and stator elements

A combined analytical-computational method has been developed to calculate the transient pressure field and rotordynamic coefficients for high-pressure annular seals. The solution procedure applies to constant-clearance or the convergent tapered geometries of multistage centrifugal pumps which may have different surface roughness conditions on the stator and rotor seal elements. In experimental calculations with the method, the turbulent equations of Hirs (1973) are modified slightly to account for different surface roughness conditions, and a perturbation analysis is employed to develop zeroth and first order perturbation equations. Zeroth equations are also used to define both the leakage and circumferential flow due to shear stresses around the stator and rotor surfaces. The solution to analytical equations for four different surface roughnesses confirm the predicted net damping for the seals. A round-holed stator pattern yielded the highest net damping and lowest leakage of all the seals tested.

Childs, D. W.↗
NASA NTRS2016

Radiative Transfer Simulations of the Two-Dimensional Ocean Glint Reflectance and Determination of the Sea Surface Roughness

An optimized discrete-ordinate radiative transfer model (DISORT3) with a pseudo-two-dimensional bidirectional reflectance distribution function (BRDF) is used to simulate and validate ocean glint reflectances at an infrared wavelength (1036 nm) by matching model results with a complete set of BRDF measurements obtained from the NASA cloud absorption radiometer (CAR) deployed on an aircraft. The surface roughness is then obtained through a retrieval algorithm and is used to extend the simulation into the visible spectral range where diffuse reflectance becomes important. In general, the simulated reflectances and surface roughness information are in good agreement with the measurements, and the diffuse reflectance in the visible, ignored in current glint algorithms, is shown to be important. The successful implementation of this new treatment of ocean glint reflectance and surface roughness in DISORT3 will help improve glint correction algorithms in current and future ocean color remote sensing applications.

glint↗
NASA NTRS1959

Boundary-Layer Transition on Hollow Cylinders in Supersonic Free Flight as Affected by Mach Number and a Screwthread Type of Surface Roughness

The effects of Mach number and surface-roughness variation on boundary-layer transition were studied using fin-stabilized hollow-tube models in free flight. The tests were conducted over the Mach number range from 2.8 to 7 at a nominally constant unit Reynolds number of 3 million per inch, and with heat transfer to the model surface. A screwthread type of distributed two-dimensional roughness was used. Nominal thread heights varied from 100 microinches to 2100 microinches. Transition Reynolds number was found to increase with increasing Mach number at a rate depending simultaneously on Mach number and roughness height. The laminar boundary layer was found to tolerate increasing amounts of roughness as Mach number increased. For a given Mach number an optimum roughness height was found which gave a maximum laminar run greater than was obtained with a smooth surface.

James, Carlton S.↗
NASA NTRS1965

Rough surface improves stability of air- sounding balloons

Aerodynamic stability of balloons used for measuring the intensity and direction of atmospheric winds at various elevations is improved by incorporating a rough surface on the balloons. The rough-surfaced balloon is useful for collecting wind profiles and other meteorological data.

Scoggins, J. R.↗
NASA NTRS1993

Polarimetric thermal emission from rough surfaces

Recent theoretical works have suggested the potential of passive polarimetry in the remote sensing of geophysical media. It was shown that the third Stokes parameter U of the thermal emission may become larger for azimuthally asymmetric fields of observation. In order to investigate the potential applicability of passive polarimetry to the remote sensing of ocean surface, measurements of the polarimetric thermal emission from a sinusoidal water surface and a numerical study of the polarimetric thermal emission from randomly rough ocean surfaces were performed. Measurements of sinusoidal water surface thermal emission were performed using a sinusoidal water surface which was created by placing a thin sheet of fiberglass with a sinusoidal profile in two dimensions extended infinitely in the third dimension onto a water surface. The theory of thermal emission from a 'two-layer' periodic surface is derived and the exact solution is performed using both the extended boundary condition method (EBC) and the method of moments (MOM). The theoretical predictions are found to be in good agreement with the experimental results once the effects of the radiometer antenna pattern are included and the contribution of background noise to the measurements is modeled. The experimental results show that the U parameter indicates the direction of periodicity of the water surface and can approach values of up to 30 K for the surface observed. Next, a numerical study of polarimetric thermal emission from randomly rough surfaces was performed. A Monte Carlo technique utilizing an exact method for calculating thermal emission was chosen for the study to avoid any of the limitations of the commonly used approximate methods in rough surface scattering. In this Monte Carlo technique, a set of finite rough surface profiles in two dimensions with desired statistics was generated and extended periodically. The polarimetric thermal emission from each surface of the set was then calculated using both the EBC and the MOM and the results were averaged. The surface statistics chosen were intended to model a wind perturbed ocean surface in the X to Ku band microwave region. The results indicate that the U parameter is sensitive to the azimuthal angle between the surface periodicity and the looking angle and to the rms height of the surface, and that the U parameter is fairly insensitive to variations in polar angle, permittivity, surface power law spectrum, and surface spectrum high frequency cutoff. These properties give further strength to the idea of using the U parameter to detect wind direction over the ocean.

Johnson, J. T.↗
NASA NTRS1976

Selection of remote sensing techniques - Surface roughness information from 3 cm wavelength SLAR images

The value of SLAR (Side-Looking Airborne Radar) image data for detecting and measuring small-scale surface roughness is examined, using as an example the Cottonball Basin in Death Valley National Monument, California. The SLAR image was obtained by an X-band (3 cm wavelength) synthetic aperture radar system operated at an altitude of 10,732 m above sea level. The polarization of the transmitted and received signals was horizontal. Film density values were used to produce color hypsometric maps of small-scale surface irregularities. It is shown that semi-quantitative surface roughness information, from uniquely flat surfaces such as the Cottonball Basin, can be obtained by analysis of 3 cm wavelength SLAR images calibrated by limited field measurements. Quantitative roughness data could be obtained with proper consideration of modifying surface and radar system parameters.

Schaber, G. G.↗
NASA NTRS1979

Rough surface wavelength measurement through self mixing of Doppler microwave backscatter

A microwave backscatter technique is presented that has the ability to sense the dominant surface wavelength of a random rough surface. The purpose of this technique is to perform this measurement from an aircraft or spacecraft, wherein the horizontal velocity of the radar is an important parameter of the measurement system. Attention will be directed at water surface conditions for which a dominant wavelength can be defined, then the spatial variations of reflectivity will have a two dimensional spectrum that is sufficiently close to that of waves to be useful. The measurement concept is based on the relative motion between the water waves and a nadir looking radar, and the fact that while the instantaneous Doppler frequency at the receiver returned by any elementary group of scatterers on a water wave is monotonically changing, the difference in the Doppler frequency between any two scattering 'patches' stays approximately constant as these waves travel parallel to the major axis of an elliptical antenna footprint. The results of a theoretical analysis and a laboratory experiment with a continuous wave (CW) radar that encompasses several of the largest waves in the illuminated area show how the structure in the Doppler spectrum of the backscattered signal is related to the surface spectrum and its parameters in an especially direct and simple way when an incoherent envelope detector is the receiver.

Weissman, D. E.↗
NASA NTRS1989

A numerical investigation of the influence of surface roughness on heat transfer in ice accretion

The flowfield and resulting heat transfer rate over a series of ice accretion shapes is obtained by solving the Navier-Stokes equations. The influence of surface roughness on surface heat transfer is examined by including blockage, form drag, and stagnation heating effects as source terms in the governing equations. The results indicate increases of a factor of three in cooling rates due to distributed roughness compared to smotth surfaces. In addition, droplet impingement efficiencies are studied for the same series of ice accretion shapes using a time-dependent solution procedure.

Scott, J. N.↗
NASA NTRS1961

Pressure Distributions and Wave Drag Due to Two-Dimensional Fabrication-Type Surface Roughness on an Ogive Cylinder at Mach Numbers of 1.61 and 2.01

An investigation has been made at Mach numbers of 1.61 and 2.01 and over a range of free-stream Reynolds number per foot from about 1.2 x 10(exp 6) to 8.3 x 10(exp 6) to determine the pressure distributions and wave drags due to two-dimensional fabrication-type surface roughness. Ten types of surface roughness, including step, wave, crease, and swept configurations were investigated. The tests were made on an ogive cylinder of fineness ratio 12.2, the roughness elements covering the cylindrical portion of the model. The results indicate that wave drag is the major component of the drag due to roughness at supersonic speeds. The pressure distributions over the roughness elements were generally found to be in good agreement with linearized two-dimensional theory except for regions of the elements affected by boundary-layer separation and shock detachment. There was little or no effect of Reynolds number except on the pressures within the regions influenced by separation or shock detachment. Inasmuch as most of the roughness configurations were affected by flow separation and shock detachment, there was generally an effect of Reynolds number on the roughness wave drag. This wave drag decreased as the free-stream Reynolds number was decreased.

Czarnecki, K. R.↗
NASA NTRS1997

Estimation of Bare Surface Soil Moisture and Surface Roughness Parameter Using L-Band SAR Image Data

An algorithm based on a fit of the single-scattering Integral Equation Method (IEM) was developed to provide estimation of soil moisture and surface roughness parameter (a combination of rms roughness height and surface power spectrum) from quasi-polarized synthetic aperture radar (SAR) measurements. This algorithm was applied to a series of measurements acquired at L-band (1.25 GHz) from both AIRSAR (Airborne Synthetic Aperture Radar operated by Jet Propulsion Laboratory) and SIR-C (Spaceborne Imaging Radar-C) over a well-managed watershed in southwest Oklahoma. It was found that the two co-polarized backscattering coefficients and their combinations would provide the best input to the algorithm for estimation of soil moisture and roughness parameter. Application of the inversion algorithm to the co-polarized measurements of both AIRSAR and SIR-C resulted in estimated values of soil moisture and roughness parameter for bare and short-vegetated fields that compared favorably with those sampled on the ground. The root-mean-square (rms) errors of the comparison were found to be 3.4% and 1.9 dB for soil moisture and surface roughness parameter, respectively.

Shi, Jian-Cheng↗