Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “structural modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

A Modern Load Relief Guidance Scheme for Space Launch Vehicles

Launch vehicle load relief algorithms are concerned with realizing a reduction of transient bending moments near maximum dynamic pressure. Traditional approaches to load relief typically use inner-loop acceleration feedback to reduce the wind-induced angle of attack. When implemented in the inner loop, load relief bandwidth is necessarily limited by the achievable stability margins, and when acceleration feedback is employed, by the uncertainty associated with structural modes that couple with the body-mounted accelerometer. The structure of inner loop load relief increases the dimensionality of the flight control gain and filter optimization problem. Most importantly, classical load relief laws do not take advantage of high-rate and high-accuracy GPS-aided inertial velocity data that is readily available from modern strap down IMUs. In this paper, a novel load relief guidance scheme is described that uses direct angle-of-attack feedback in a clever mechanization. The steering commands are determined by examining the wind-perturbed dynamics of a launch vehicle with respect to a gravity turn ascent trajectory. An angle of attack estimate is derived from GPS-aided inertial data and pre-launch range wind measurements, and it is shown that a reduction worst-case rigid-body loads can be realized without requiring air data. The algorithm also includes a high-rate navigation data preprocessing scheme that operates directly on the IMU delta-theta and delta-velocity measurements in order to produce a filtered acceleration estimate at the vehicle center of mass. The outer-loop guidance scheme simplifies the design process for the classical inner-loop autopilot. Algorithm performance is demonstrated using Monte Carlo analysis of a representative liquid booster in a production high fidelity launch vehicle simulation.

NESC↗

Effects of experimentally measured pressure oscillations on the vibration of a solid rocket motor

Results are presented of firing a Nike rocket against a backstop for the purpose of obtaining pressure fluctuations in the rocket case and determining their relationship to structural vibrations of the case. Special care was required to obtain these pressure fluctuations because of the much higher static pressure generated in the rocket. Very small pressure fluctuations within the rocket case can cause significant vibration levels. A previously observed high frequency was shown to decrease with time before completely disappearing at about 1 second of burning time. The vibration of the case itself is probably related to the longitudinal structural modes at frequencies below 500 Hz and is dependent on local structural conditions at frequencies above this value.

Schoenster, J. A.↗

Lanczos modes for reduced-order control of flexible structures

Lanczos mode models represent low-frequency forced response better than do normal mode models and can be developed for both continuous and finite element structural representations. It was recommended that Lanczos mode models for systems with multiple input and/or rigid body modes should be developed; numerical stability of the Lanczos algorithm should be assessed; and control system designs employing the Lanczos mode models should be attempted.

Craig, Roy R., Jr.↗

Buffet induced structural/flight-control system interaction of the X-29A aircraft

High-alpha flight creates unique aerodynamic phenomena which increase the level of structural mode excitation; in conjunction with high-gain digital control systems, this structural response may result in an aeroservoelastic interaction. One such interaction has been observed during high-alpha flight testing of the X-29A. Data are presented which demonstrate the enhanced modal power in this aircraft's structural accelerometers, the feedback sensors, and the command signals as a function of alpha value. The structural interaction is traced from the aerodynamic buffet to the flight-control surfaces.

Voracek, David F.↗

Flutter Analysis for Turbomachinery Using Volterra Series

The objective of this paper is to describe an accurate and efficient reduced order modeling method for aeroelastic (AE) analysis and for determining the flutter boundary. Without losing accuracy, we develop a reduced order model based on the Volterra series to achieve significant savings in computational cost. The aerodynamic force is provided by a high-fidelity solution from the Reynolds-averaged Navier-Stokes (RANS) equations; the structural mode shapes are determined from the finite element analysis. The fluid-structure coupling is then modeled by the state-space formulation with the structural displacement as input and the aerodynamic force as output, which in turn acts as an external force to the aeroelastic displacement equation for providing the structural deformation. NASA's rotor 67 blade is used to study its aeroelastic characteristics under the designated operating condition. First, the CFD results are validated against measured data available for the steady state condition. Then, the accuracy of the developed reduced order model is compared with the full-order solutions. Finally the aeroelastic solutions of the blade are computed and a flutter boundary is identified, suggesting that the rotor, with the material property chosen for the study, is structurally stable at the operating condition, free of encountering flutter.

computational fluid dynamics↗

Effect of control surface mass unbalance on the stability of a closed-loop active control system

The effects on stability of inertial forces arising from closed-loop activation of mass-unbalanced control surfaces are studied analytically using inertial energy approach, similar to the aerodynamic energy approach used for flutter suppression. The limitations of a single control surface like a leading-edge (LE) control or a trailing-edge (TE) control are demonstrated and compared to the superior combined LE-TE mass unbalanced system. It is shown that a spanwise section for sensor location can be determined which ensures minimum sensitivity to the mode shapes of the aircraft. It is shown that an LE control exhibits compatibility between inertial stabilization and aerodynamic stabilization, and that a TE control lacks such compatibility. The results of the present work should prove valuable, both for the purpose of flutter suppression using mass unbalanced control surfaces, or for the stabilization of structural modes of large space structures by means of inertial forces.

Nissim, E.↗

Space shuttle pogo active controller design using frequency domain optimization

A frequency domain parameter optimization technique was used to design active pogo suppression controls for the space shuttle. The technique uses a conjugate gradient search procedure and is well suited for designing low-order controllers for higher order systems. The shuttle model was a two-pump and six-structural-mode linear model representing a worst-case condition. A promising feedback controller structure was found to be a lead-lag design.

Seidel, R. C.↗

Forced magnetic reconnection in a plasma sheet with localized resistivity profile excited by lower hybrid drift type instability

A forced magnetic reconnection process with a temporal evolution of resistivity is studied for a plasma sheet with a nonuniform resistivity profile based on the nonlocal mode structure of the lower hybrid drift type instability. The growth rate of the mode found is almost independent of the resistivity at the neutral sheet, but depends on the resistivity of the region of maximum density gradient away from the neutral sheet. This is studied by using both a nonlinear numerical MHD simulation and a linear theory. The mode may be relevant to the prevalent theoretical concept of MHD reconnection and the localized anomalous resistivity profile based on the lower hybrid drift instability.

Hoshino, M.↗

Topological variation in the magnetic field line at the dayside magnetopause

This paper uses normal mode analysis to examine topological changes in magnetic field lines at the magnetopause. For a modified Harris sheet, the normal modes include a symmetric solution (tearing mode) and an antisymmetric solution (twisting mode). Both modes form flux ropes. The tearing mode in the presence of shear flow is studied. By modeling the external region plasma with drift kinetic formalism, the growth rate of the tearing mode is found to be reduced by shear flow. On the other hand, the shear flow generates a Kelvin-Helmholtz instability which makes the magnetic field perturbation a twisting mode structure. When magnetopause parameters are used, it is difficult to induce a tearing mode in the presence of shear flow, though a shear flow twisting mode did grow under these conditions.

Wang, Zhi↗

Amplitude Noise Reduction of Ion Lasers with Optical Feedback

A reduction in amplitude noise on the output of a multi-mode continuous-wave Ar-ion laser was previously demonstrated when a fraction of the output power was retroreflected back into the laser cavity. This result was reproduced in the present work and a Fabry-Perot etalon was used to monitor the longitudinal mode structure of the laser. A decrease in the number of operating longitudinal cavity modes was observed simultaneously with the introduction of the optical feedback and the onset of the amplitude noise reduction. The noise reduction is a result of a reduced number of lasing modes, resulting in less mode beating and amplitude fluctuations of the laser output power.

Herring, Gregory C.↗

Transformable Linkage-Based Gripper for Multi-Mode Grasping and Manipulation

Gripper hardware design often involves a trade-off between distinct and sometimes opposing goals (e.g., high grasping force vs. gentleness). To address this trade-off within a single device, we present a multi-mode gripper with fingers that are scissor linkages, that can actively transform between three distinct modes by varying the number and locations of mechanical singularities. Each of these modes has properties that are suitable for specific needs. Mode 1 provides high grip strength, using a short lever arm and rigid structure. Mode 2 allows precise finger positioning and in-hand manipulation, using two independently controlled DOFs per finger. Mode 3 provides underactuated grasping that can passively adapt to delicate or irregularly shaped objects, with four DOFs per finger. The kinematic relationships, joint torques, and fingertip forces are derived analytically for each of the three modes. Gripper performance and the kinematic model are verified experimentally.

Junghan Kwon↗

Observations of the 2-day wave in NMC stratospheric analyses

Observational characteristics of the 2-day wave, a westward-propagating zonal wave 3 oscillation in the summer subtropical upper stratosphere and mesosphere, are studied based on five years of National Meteorological Center (NMC) operational stratospheric analyses. These data show episodic occurrence of the 2-day wave in the upper stratosphere in January (centered near 20 deg S) and July - August (centered near 20 deg N). These episodes are strongly correlated with observed reversals of the zonal mean potential vorticity gradient near the core of the summer easterly jet, consistent with previous suggestions that the 2-day wave is generated by an in situ instability of this jet. On the other hand, the horizontal and vertical structure of the waves is very similar to that calculated by Salby for a global normal-mode Rossby wave. The combination of normal-mode structure and instability signature suggests that the 2-day wave is a near-resonant mode forced by dynamical instability.

Randel, William J.↗

Fixed- and Free-Mode Flutter Derivatives during Aeroelastic Optimization

Aeroelastic flutter design derivatives may be approximated by ignoring the sensitivity of the structural mode shapes. This “fixed-mode” derivative is less-expensive to compute than the exact “free-mode” derivative (which accommodates the mode shape dependency), but also may provide inaccurate sensitivities for optimization. This work formulates both fixed- and free-mode flutter derivatives, and demonstrates the conditions under which they are equivalent. Two different types of fixed-mode derivatives are also developed in this work. Using a cantilevered-plate demonstration problem with both shape and sizing design parameters, the accuracy of the free-mode derivative and the two fixed-mode derivatives, are all demonstrated via gradient-based optimization.

Bret K. Stanford↗

Interior noise control ground test studies for advanced turboprop aircraft applications

The measurement and analysis procedures are documented, and the results of interior noise control ground tests conducted on a DC-9 aircraft test section are summarized. The objectives of these tests were to study the fuselage response characteristics of treated and untreated aircraft with aft-mount advanced turboprop engines and to analyze the effectiveness of selected noise control treatments in reducing passenger cabin noise on these aircraft. The results of fuselage structural mode surveys, cabin cavity surveys and sound intensity surveys are presented. The performance of various structural and cabin sidewall treatments is assessed, based on measurements of the resulting interior noise levels under simulated advanced turboprop excitation.

Simpson, Myles A.↗

Control-structure interaction in precision pointing servo loops

The control-structure interaction problem is addressed via stability analysis of a generic linear servo loop model. With the plant described by the rigid body mode and a single elastic mode, structural flexibility is categorized into one of three types: (1) appendage, (2) in-the-loop minimum phase, and (3) in-the-loop nonminimum phase. Closing the loop with proportional-derivative (PD) control action and introducing sensor roll-off dynamics in the feedback path, stability conditions are obtained. Trade studies are conducted with modal frequency, modal participation, modal damping, loop bandwidth, and sensor bandwidth treated as free parameters. Results indicate that appendage modes are most likely to produce instability if they are near the sensor rolloff, whereas in-the-loop modes are most dangerous near the loop bandwidth. The main goal of this paper is to provide a fundamental understanding of the control-structure interaction problem so that it may benefit the design of complex spacecraft and pointing system servo loops. In this framework, the JPL Pathfinder gimbal pointer is considered as an example.

Spanos, John T.↗

Ground Vibration Testing at NASA Armstrong, Emphasizing on Passive Aeroelastic Tailored Wing Ground Vibration Test Using Fixed Base Correction Method

How does experimental mechanics contribute to aircraft aeroelastic airworthiness? The aviation community is always improving analysis and testing techniques to realize quicker, cheaper, reliable solutions. A ground vibration test (GVT) is conducted to identify structural mode shapes, frequencies, and damping values to validate analytical models used for flutter analysis, which shows whether a structure has acceptable aeroelastic flutter margins for airworthiness. The FLL recently conducted a GVT of the Passive Aeroelastic Tailored (PAT) Wing using an experimental modal technique called Fixed Base Correction (FBC). The GVT objective was to obtain the PAT wing modal characteristics to compare test results with finite element model (FEM) results for the tow-steered wingbox.

loads testing↗

Viscous damped space structure for reduced jitter

A technique to provide modal vibration damping in high performance space structures was developed which uses less than one once of incompressible fluid. Up to 50 percent damping can be achieved which can reduce the settling times of the lowest structural mode by as much as 50 to 1. This concept allows the designers to reduce the weight of the structure while improving its dynamic performance. Damping by this technique is purely viscous and has been shown by test to be linear over 5 orders of input magnitude. Amplitudes as low as 0.2 microinch were demonstrated. Damping in the system is independent of stiffness and relatively insensitive to temperature.

Wilson, James F.↗