Collective flow without hydrodynamics: simulation results for relativistic ion collisions
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
The Savannah River National Laboratory (SRNL) recently received a deposit sample from the Melter Primary Off Gas System (POG) of the Defense Waste Processing Facility (DWPF). This sample was composed of material that had been collected while the quencher was in operation January 27, 2011 through March 31, 2011. DWPF requested, through a technical assistance request, characterization of the melter off-gas deposits by x-ray diffraction (XRD), scanning electron microscopy (SEM), and chemical analysis. The purpose of the Melter Off-Gas System is to reduce the amount of radioactive particles and mercury in the gases vented to the atmosphere. Gases emitted from the melter pass through the primary film cooler, quencher, Off-Gas Condensate Tank (OGCT), Steam Atomized Scrubbers (SAS), a condenser, a high efficiency mist eliminator, and a high efficiency particulate air filter, before being vented to the Process Vessel Vent System. The film coolers cool the gases leaving the melter vapor space from {approx}750 C to {approx}375 C, by introducing air and steam to the flow. In the next step, the quencher cools the gas to about 60 C by bringing the condensate from the OGCT in contact with the effluent (Figure 1). Most of the steam in the effluent is then condensed and the melter vapor space pressure is reduced. The purpose of the OGCT is to collect and store the condensate formed during the melter operation. Condensate from the OGCT is circulated to the SAS and atomized with steam. This atomized condensate is mixed with the off-gas to wet and join the particulate which is then removed in the cyclone. The next stage incorporates a chilled water condenser which separates the vapors and elemental mercury from the off-gas steam. Primary off-gas deposit samples from the DWPF melter have previously been analyzed. In 2003, samples from just past the film cooler, from the inlet of the quencher and inside the quencher were analyzed at SRNL. It was determined that the samples were a mixture of sludge and glass frit. The major component was Si along with Fe, Al, and other elements in the radioactive waste being processed. The deposits analyzed also contained U-235 fission products and actinide elements. Prior to that, deposits in the off-gas system in the DWPF nonradioactive half scale melter and the one-tenth scale integrated DWPF melter system were analyzed and determined to be mixtures of alkali rich chlorides, sulfates, borates, and fluorides entrained with iron oxides, spinels and frit particles formed by vapor-phase transport and condensation. Additional work was performed in 2007 in which researchers similarly found the deposits to be a combination of sludge and frit particles.
This paper presents reduced-order modeling of thermal power dispatch (TPD) from a pressurized water reactor (PWR) for providing heat to nearby heat consuming industrial processes that seek to take advantage of nuclear heat to reduce carbon emissions. The reactor model includes the neutronics of the reactor core, thermal–hydraulics of the primary coolant cycle, and a three-lump model of the steam generator (SG). The secondary coolant cycle is represented with quasi-steady state mass and energy balance equations. The secondary cycle consists of a steam extraction system, high-pressure and low-pressure turbines, moisture separator and reheater, high-pressure and low-pressure feedwater heaters, deaerator, feedwater and condensate pumps, and a condenser. The steam produced by the SG is distributed between the turbines and the extraction steam line (XSL) that delivers steam to nearby industrial processes, such as production of clean hydrogen. The reduced-order simulator is verified by comparing predictions with results from separate validated steady-state and transient full-scope PWR simulators for TPD levels between 0% and 70% of the rated reactor power. All simulators indicate that the flow rate of steam in the main steam line and turbine systems decrease with increasing TPD, which causes a reduction in PWR electric power generation. The results are analyzed to assess the impact of TPD on system efficiency and feedwater flow control. Due to the simplicity of the proposed reduced-order model, it can be scaled to represent a PWR of any size with a few parametric changes. In the future, the proposed reduced-order model will be integrated into a power system model in a digital real-time simulator (DRTS) and physical hardware-in-the-loop simulations.
Best-Estimate plus Uncertainty (BEPU) methods are slowly supplanting the use of deterministic analysis methods for thermal-hydraulic analyses. As the uncertainty methodologies evolve it is expected that, where both experimental techniques allow and data are available, there will be a shift to quantifying the uncertainty in increasingly more fundamental parameters. For example, for annular flow in a three-field analysis environment (vapor, liquid film, droplet), the driving parameters would be: a) film interfacial shear stress, b) droplet drag, c) droplet entrainment rate and d) droplet deposition rate. An improved annular flow modeling package was recently developed and implemented in an in-house version of the COBRA-TF best-estimate subchannel analysis tool (Lane, 2009). Significant improvement was observed in the code-to-data predictions of several steam-water annular flow tests following the implementation of this modeling package; however, to apply this model set in formal BEPU analysis requires uncertainty distributions to be determined. The unique aspect of annular flow, and the topic of the present work, is the strong coupling between the interfacial drag, entrainment and deposition phenomena. Ideally the uncertainty in each phenomenon would be isolated; however, the situation is further complicated by an inability to experimentally isolate and measure the individual rate processes (particularly entrainment rate), which results in available experimental data that are inherently integral in nature. This paper presents a methodology for isolating the individual physical phenomena of interest, to the extent that the currently available experimental data allow, and developing the corresponding uncertainty distributions for annular flow. (authors)
Usually, the spacer grid decreases the flow area and then enhances the convective heat transfer due to the flow acceleration and the turbulence increases. Their phenomena is shown in both egg-crate style spacer grids and mixing vane grids. Also, the mixing vane swirls the flow and enhances the convective heat transfer. In this study, the effect of spacer grid model of TRACE was performed on RBHT (Rod Bundle Heat Transfer) reflood tests. The RBHT tests were designed to conduct several separate-effects tests such as single phase steam cooling, low flow boiling and dispersed flow film boiling heat transfer, which is very important during a large break loss of coolant accident (LOCA). This facility has a heated length of 3.66 m (12.0 ft), which is typical of a pressurized water reactor (PWR) fuel assembly. The test section consists of a 7 x 7 rod bundle with 45 heated electrical rods, and seven mixing vane grids. The electrical rods have a diameter of 9.5 mm and are arranged with a 12.6 mm pitch with 45 heater rods and four unheated rods. Tests 1096, 1108, 1170, 1196, 1285 and 1383, which are in the TRACE assessment manual , were selected to evaluate the effect of the spacer grid model of TRACE. (authors)
A high temperature gas reactor, HTGR, can produce industrial process steam, high-temperature heat-transfer gases, and/or electricity. In conventional industrial processes, these products are generated by the combustion of fossil fuels such as coal and natural gas, resulting in significant emissions of greenhouse gases such as carbon dioxide. Heat or electricity produced in an HTGR could be used to supply process heat or electricity to conventional processes without generating any greenhouse gases. Process heat from a reactor needs to be transported by a gas to the industrial process. Two such gases were considered in this study: helium and steam. For this analysis, it was assumed that steam was delivered at 17 MPa and 540 C and helium was delivered at 7 MPa and at a variety of temperatures. The temperature of the gas returning from the industrial process and going to the HTGR must be within certain temperature ranges to maintain the correct reactor inlet temperature for a particular reactor outlet temperature. The returning gas may be below the reactor inlet temperature, ROT, but not above. The optimal return temperature produces the maximum process heat gas flow rate. For steam, the delivered pressure sets an optimal reactor outlet temperature based on the condensation temperature of the steam. ROTs greater than 769.7 C produce no additional advantage for the production of steam.
Several supplemental technologies for treating and immobilizing Hanford low activity waste (LAW) are being evaluated. One such immobilization technology being considered is the Fluidized Bed Steam Reforming (FBSR) product, which is granular and will be monolithed into a final waste form. The granular component is composed of insoluble sodium aluminosilicate (NAS) feldspathoid minerals. Production of the FBSR mineral product has been demonstrated at the industrial, engineering, and laboratory scales. Single-Pass Flow-Through (SPFT) tests at various flow rates have been conducted with the granular products fabricated using the engineering- and laboratory-scale methods. Results show that the forward dissolution rate for the engineering-scale mineral product is 0.6 (±0.2)x10{sup -3} g/m{sup 2}d while the forward dissolution rate for the laboratory-scale mineral product is 1.3 (±0.5)x10{sup -3} g/m{sup 2}d. (authors)
In recent years, interest in increasing the efficiency of power plants based on steam generation has led to the need to develop and qualify materials capable of operating at steam temperatures and pressures significantly higher than those employed in current power plants. The overall focus of this international program is on using ferritic-martensitic steels to the maximum possible temperature, before switching to austenitic steels and/or Ni-based alloys. The relatively low Cr content of these alloys raises concerns regarding their resistance to steam oxidation at these higher temperatures. Earlier work in this collaboration addressed the reliability of data from atmospheric pressure, laboratory-based steam oxidation tests. This raised issues regarding how representative the laboratory-grown oxides were compared to those formed on service-exposed material and how the tests could be made more reliable by introducing added complexity. In general laboratory-scale exposures are conducted under isothermal conditions at ambient or slightly elevated pressure, using a relatively low flow rate of steam. The coupons used in these tests are normally flat cuboids which have been ground to homogenise the surface and remove any pre-existing features. However, there is a concern that these samples and exposures are not representative of service conditions, and so it is necessary to quantify the influence of transient conditions, such as heat flux, pressure and sample geometry/surface conditions. To address such concerns a new collaborative program of work was initiated to determine the influence of these added features on oxidation kinetics and oxide scale morphology. The overall aim was to improve the understanding of alloy performance in ultrasupercritical (USC) steam conditions and qualify suitable test procedures.
A challenge was posed to the criticality safety consultant to consider whether instrumentation identified by Plant Management in an existing facility could be claimed as appropriate safety measures to ensure compliance with moderator content limits in uranium dioxide (UO{sub 2}) powder. During processing of low enriched UO{sub 2}, trays of powder are heated in a steam and hydrogen environment in order to reduce fluoride levels. Whilst in the furnace environment criticality safety is ensured by the geometry of the furnace trays used to convey the powder; however, upon leaving the furnace the UO{sub 2} is bulked to a 210 litre drum subject to limited moderation control. Under fault conditions there is a potential that the powder may become wetted due to an imbalance in furnace gas flows resulting in steam condensing in the cooling section of the furnace. Therefore, the safety case methodology followed suggests that two independent and diverse safety measures are provided to terminate the progression of the fault(s) to criticality. The existing criticality safety case credits an infra-red moisture meter as one of two safety measures; however, the calibration procedure required to ensure this device remains suitable is a considerable challenge from a plant operability perspective. As an initial review failed to identify any suitable like-for-like replacement, the National Nuclear Laboratory (NNL) Nuclear Safety Section were requested by the customer to consider the existing criticality safety case and investigate whether any existing instrumentation could be used as an alternative method of detecting conditions in which excess moisture could be present within the furnace trays. A number of solutions were proposed and the benefits and challenges around each are discussed in this paper, concluding with the approach adopted by the project. (authors)
Hydrogen or hydrogen blend fuels are expected to replace natural gas in land-based industrial gas turbines (IGTs) to support a greener power economy. Silicon carbide (SiC) base ceramic matrix composites (CMCs) are considered for replacement of Ni-based superalloys to facilitate future efficiency improvements. SiC CMCs require environmental barrier coatings (EBCs) to mitigate volatilization from high-temperature steam, thus making the EBC lifetime critical information for identifying CMC component lifetimes. The goal of this project is to determine the maximum bond coating temperature underneath the EBC for achieving an IGT component lifetime goal of 25,000 h, which is far greater than current CMC component lifetime requirements for aero-turbine applications. To provide data for the lifetime model, laboratory testing used plasma-sprayed rare-earth silicate EBCs on monolithic SiC substrates with an intermediate Si bond coating. Specimens exposed to 1-h thermal cycles in flowing air-steam environments and reaction kinetics were assessed from 700°-1350°C by measuring the thickness of the thermally grown silica scales. The silica growth and phase transformation appear critical in predicting EBC lifetime and several strategies have been explored to reduce the oxide growth rate and improve EBC durability at elevated temperatures. Advanced characterization using Raman spectroscopy has helped clarify this system.
In CFD simulations of flow mixing in a steam generator (SG) during natural circulation, one is faced with the problem of representing the thousands of SG U-tubes. Typically simplifications are made to render the problem computationally tractable. In particular, one or a number of tubes are lumped in one volume which is treated as a single porous medium. This approach dramatically reduces the computational size of the problem and hence simulation time. In this work, we endeavor to investigate the adequacy of this approach by performing two separate simulations of flow in a mock-up with 262 U-tubes, i.e. one in which the porous media model is used for the tube bundle, and another in which the full geometry is represented. In both simulations, the Reynolds Stress (RMS) model of turbulence is used. We show that in steady state conditions, the porous media treatment yields results which are comparable to those of the full geometry representation (temperature distribution, recirculation ratio, hot plume spread, etc). Hence, the porous media approach can be extended with a good degree of confidence to the full scale SG. (authors)
The helically-coiled heat exchanger (HCSG) offers advantages over straight tubes such as compactness in geometry, increased heat transfer coefficients, and capability to absorb thermal expansion. In this study, the time-resolved velocity field data of shell-side crossflow over a five-layer helically coiled steam generator geometry was obtained using Particle Image Velocimetry (PIV) between adjacent rods in four regions with up to 5000 frames per second (5 kHz) at approximately Re u = 3600. The slant rod bundle created different flow patterns in different regions. Proper Orthogonal Decomposition (POD) revealed high-energy-mode flow structures. Due to the confined flow channel geometry, the large flow structures were not advected resulting in no strong POD mode paring. Continuous Wavelet Transform (CWT) visualized the characteristics of flow fluctuation in time and frequency domain simultaneously, which ranged in Strouhal number, S u , between 0.03 and 1.17. In the wake regions of the rods, flows changed in both pattern and magnitude over time. Once a pattern formed, it continued for relatively shorter than straight tube arrays, before changing the pattern again. The histograms of the POD time coefficients presented this multimodal flow characteristics. The current study focuses more on whole flow field analyses in the selected regions rather than local point-wise analyses. Finally, this study revealed that various Strouhal numbers can exist in the helically coiled heat exchanger geometry, which was not observed in straight tube arrays. In particular, Strouhal numbers smaller than 0.1 do not seem to be caused by vortex shedding but seem to be the result of the combination of complex geometry and possible multimodal trends. Based on the current observation, further works would involve intensive instantaneous point-wise analyses on the interactions between important locations such as separation points, stagnation points, shear layers, etc.
Several supplemental technologies for treating and immobilizing Hanford low activity waste (LAW) are being evaluated. One such immobilization technology being considered is the Fluidized Bed Steam Reforming (FBSR) granular product. The FBSR granular product is composed of insoluble sodium aluminosilicate (NAS) feldspathoid minerals. Production of the FBSR mineral product has been demonstrated both at the industrial and laboratory scale. Single-Pass Flow-Through (SPFT) tests at various flow rates have been conducted with the granular products fabricated using these two methods. Results show that the materials exhibit a relatively low forward dissolution rate on the order of 10-3 g/(m2d) with the material made in the laboratory giving slightly higher values.
Experiments to prepare activated carbon by microwave heating indicated that microwave energy can decrease reaction temperature, save the energy and shorten processing time remarkably compared to conventional heating, owing to its internal and volumetric heating effects. The above results were based on the laboratory-scale experiments. It is desirable to develop a pilot-scale microwave heating equipment and investigate the parameters with the aim of technological industrialization. In the present study, the components and features of the self-invented equipment were introduced. The temperature rise curves of the chars were obtained. Iodine numbers of the activated carbons all exceed the state standard of China under the following conditions: 25 kg/h charging rate, 0.42 rev/min turning rate of ceramic tube, flow rate of steam at pressure of 0.01 MPa and 40 kW microwave heating power after 60 kW pre-activation for 30 min. Pore structure of the sample obtained at a time point of 46 h, which contained BET surface area, and pore size distributions of micropores and total pores, was tested by nitrogen adsorption at 77 K.
This document details the computational fluid dynamic and system-level modeling, including a mechanistic representation of a Terry turbopump. Until this recent effort, data and modeling results show that a Terry turbine, flowing air (or steam) at a certain rate, can develop the same power at two very different speeds, and has large implications with respect to understanding how a boiling water reactor's reactor core isolation cooling system or a pressurized water reactor turbine driven auxiliary feedwater system would respond to a loss of electrical power for Terry turbine speed governing. This work has provided insights in modeling uncertainties and provides confirmation for experimental efforts for the Terry turbopump expanded operating band being conducted at Texas A&M University.
The conversion of biomass into energy and chemicals is a major research and technology challenge of this century, comparable to petroleum processing in the last century. Recently we have successfully transformed both volatile liquids and nonvolatile liquids and solids into syngas with no carbon formation in autothermal catalytic reactors with residence times of ~10 milliseconds. In the proposed research program we explore the mechanisms of these processes and their extensions to other biomass sources and applications by examining different feeds, catalysts, flow conditions, and steam addition to maximize production of either syngas or chemicals. We will systematically study the catalytic partial oxidation in millisecond autothermal reactors of solid biomass and the liquid products formed by pyrolysis of solid biomass. We will examine alcohols, polyols, esters, solid carbohydrates, and lignocellulose to try to maximize formation of either hydrogen and syngas or olefins and oxygenated chemicals. We will explore molecules and mixtures of practical interest as well as surrogate molecules that contain the functional groups of biofuels but are simpler to analyze and interpret. We will examine spatial profiles within the catalyst and transient and periodic operation of these reactors at pressures up to 10 atm to obtain data from which to explore more detailed mechanistic models and optimize performance to produce a specific desired product. New experiments will examine the conversion of syngas into biofuels such as methanol and dimethyl ether to explore the entire process of producing biofuels from biomass in small distributed systems. Experiments and modeling will be integrated to probe and understand detailed reaction kinetics and the processes by which solid biomass particles are transformed into syngas and chemicals by reactive flash volatilization.
A rotary moving bed and process for separating a carbon dioxide from a gas stream is disclosed. The rotary moving bed can have a rotational assembly rotating on a vertical axis, and a plurality of sorbent cells positioned horizontally to the axis of rotation that fills a vertical space in the moving bed, where the sorbent cells adsorb the carbon dioxide by concentration swing adsorption and adsorptive displacement. The sorbent can be regenerated and the carbon dioxide recaptured by desorbing the carbon dioxide from the sorbent using concentration swing adsorption and desorptive displacement with steam. The gas flows in the system flow in a direction horizontal to the axis of rotation and in a direction opposite the rotational movement of the sorbent cells.
Here, the design of the water-cooled ceramic breeder (WCCB) blanket includes beryllium multiplier layers. At elevated temperature, beryllium reacts with steam in an exothermic reaction producing beryllium oxide and hydrogen. Such situation may occur in WCCB in the case of the rupture of one of the cooling pipes in the blanket module. This process occurs locally in a complex 3-D geometry of the blanket containing several different granular levels and a network of cooling pipes and structural supports. The process is also inherently unsteady since reaction rate depends on concentration of steam and pure beryllium which changes in time. In order to perform the detailed analysis of the process, the model of the reacting flowthrough porous media was developed and introduced into 3-D computational fluid dynamics code. In this model, granular beds are introduced as porous solids simplifying the model geometry and reducing typical mesh size to manageable amount of tens of millions of elements. A reaction rate between solid beryllium and steam is obtained from experimental results, and depends on temperature and concentration of the reactants. The differential equation for beryllium oxide fraction is introduced, allowing obtaining distributions of beryllium oxide in space and time. Multicomponent flow consisting of a homogenous mixture of steam and hydrogen is considered flowing through the porous solid with variable properties. Sink and source terms for steam and hydrogen fractions are determined by local beryllium oxide mass fraction source according to the molar ratios of beryllium steam reaction. The conjugated heat transfer approach is applied to calculate heat transfer in support structures as well as coolant flow, simultaneously with the porous medium steam flow in a blanket's granular beds. The model is validated using experimental data on beryllium steam reaction for granular bed samples.