SEARCH · Engineering Papers

Results for “start-up”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Cathode phenomena in a low power, steady state MPD thruster

Mass loss and surface temperature measurements, filter photography and SEM surface characterization are used to study cathode phenomena in a steady state self-field MPD thruster operated at power levels between 15 and 30 kW. The equilibrium cathode temperature is found to be approximately 3200 K over most of its length, for which evaporation and thermionic emission adequately explain measured erosion rates and current levels. The start-up phase is characterized by spot current attachment with associated high erosion rates.

Kelly, A. J.↗

NASA NTRS1989

Neutron and high speed photogrammetric arcjet diagnosis

Two methods for real time internal diagnostics of arcjet engines are described. One method uses cold, thermal, or epithermal neutrons. Cold neutrons are used to detect the presence and location of hydrogenous propellants. Thermal neutrons are used to delineate the edge contours of anode and cathode surfaces and to measure stress/strain. Epithermal neutrons are used to measure temperatures on arcjet surfaces, bulk material temperatures, and point temperatures in bulk materials. It is found that this method, with an exposure time of 10 min, produces at temperature accuracy for W or Re of + or - 2.5 C. The other method uses visible-light high-speed photogrammetry to obtain images of the transient behavior of the arc during start-up and to relate this behavior to electrial supply characteristics such as voltage, current, and ripple.

Stewart, P. A. E.↗

NASA NTRS1989

Performance characterization and transient investigation of multipropellant resistojets

The multipropellant resistojet thruster design initially was characterized for performance in a vacuum tank using argon, carbon dioxide, nitrogen, and hydrogen, with gas inlet pressures ranging from 13.7 to 310 kPa (2 to 45 psia) over a heat exchanger temperature range of ambient to 1200 C (2200 F). Specific impulse, the measure of performance, had values ranging from 120 to 600 seconds for argon and hydrogen respectively, with a constant heat exchanger temperature of 1200 C (2200 F). When operated under ambient conditions typical specific impulse values obtained for argon and hydrogen ranged from 55 to 290 seconds, respectively. Performance measured with several mixtures of argon and nitrogen showed no significant deviation from predictions obtained by directly weighting the argon and nitrogen individual performance results. Another aspect of the program investigating transient behavior, showed responses depended heavily on the start-up scenario used. Steady state heater temperatures were achieved in 20 to 75 minutes for argon, and in 10 to 90 minutes for hydrogen. Steady state specific impulses were achieved in 25 to 60, and 20 to 60 minutes, respectively.

Braunscheidel, Edward P.↗

NASA NTRS1988

Tribological composition optimization of chromium-carbide-based solid lubricant coatings for foil gas bearings at temperatures to 650 C

The determination of the tribilogically optimum composition of chromium-carbide-based solid lubricant coatings using a foil gas bearing test apparatus is described. The coatings contain a wear resistant chromium carbide `base stock' with the lubricant additives silver and BaF2-CaF2 eutectic. The coating composition is optimized for air-lubricated foil gas bearings at temperatures ranging from 25 to 650 C. The various compositions were prepared by powder blending, then plasma sprayed onto Inconel 718 test journals and diamond ground to the desired coating thickness and surface finish. The journals were operated against preoxidized Ni-Cr alloy foils, and the test bearings were subjected to repeated start-stop cycles under a bearing unit of 14 kPa. Sliding contact between the coated journal and the smooth foil occurs during bearing start-up before lift-off or hydrodynamic lubrication by the air film and during bearing coast-down. The bearings were tested for 9000 start-stop cycles or until specimen reached a predetermined failure level.

Dellacorte, Christopher↗

NASA NTRS1989

The US National Transonic Facility, NTF

The construction of the National Transonic Facility was completed in September 1982 and the start-up and checkout of tunnel systems were performed over the next two years. In August 1984, the Operational Readiness Review (ORR) was conducted and the facility was declared operational for final checkout of cryogenic instrumentation and control systems, and for the aerodynamic calibration and testing to commence. Also, the model access system for the cryogenic mode of operation would be placed into operation along with tunnel testing. Since the ORR, a host of operating problems resulting from the cryogenic environment were identified and solved. These range from making mechanical and electrical systems functional to eliminating temperature induced model vibration to coping with the outgassing of moisture from the thermal insulation. Additionally, a series of aerodynamic tests have demonstrated data quality and provided research data on several configurations. Some of the more significant efforts are reviewed since the ORR and the NTF status concerning hardware, instrumentation and process controls systems, operating constraints imposed by the cryogenic environment, and data quality are summarized.

Bruce, Walter E., Jr.↗

NASA NTRS1989

Synesthetic art through 3-D projection: The requirements of a computer-based supermedium

A computer-based form of multimedia art is proposed that uses the computer to fuse aspects of painting, sculpture, dance, music, film, and other media into a one-to-one synthesia of image and sound for spatially synchronous 3-D projection. Called synesthetic art, this conversion of many varied media into an aesthetically unitary experience determines the character and requirements of the system and its software. During the start-up phase, computer stereographic systems are unsuitable for software development. Eventually, a new type of illusory-projective supermedium will be required to achieve the needed combination of large-format projection and convincing real life presence, and to handle the vast amount of 3-D visual and acoustic information required. The influence of the concept on the author's research and creative work is illustrated through two examples.

Mallary, Robert↗

NASA NTRS1990

NASA systems autonomy demonstration project: Advanced automation demonstration of Space Station Freedom thermal control system

The NASA Systems Autonomy Demonstration Project (SADP) was initiated in response to Congressional interest in Space station automation technology demonstration. The SADP is a joint cooperative effort between Ames Research Center (ARC) and Johnson Space Center (JSC) to demonstrate advanced automation technology feasibility using the Space Station Freedom Thermal Control System (TCS) test bed. A model-based expert system and its operator interface were developed by knowledge engineers, AI researchers, and human factors researchers at ARC working with the domain experts and system integration engineers at JSC. Its target application is a prototype heat acquisition and transport subsystem of a space station TCS. The demonstration is scheduled to be conducted at JSC in August, 1989. The demonstration will consist of a detailed test of the ability of the Thermal Expert System to conduct real time normal operations (start-up, set point changes, shut-down) and to conduct fault detection, isolation, and recovery (FDIR) on the test article. The FDIR will be conducted by injecting ten component level failures that will manifest themselves as seven different system level faults. Here, the SADP goals, are described as well as the Thermal Control Expert System that has been developed for demonstration.

Dominick, Jeffrey↗

NASA NTRS1988

Vacuum application of thermal barrier plasma coatings

Coatings are presently applied to Space Shuttle Main Engine (SSME) turbine blades for protection against the harsh environment realized in the engine during lift off-to-orbit. High performance nickel, chromium, aluminum, and yttrium (NiCrAlY) alloy coatings, which are applied by atmospheric plasma spraying, crack and spall off because of the severe thermal shock experienced during start-up and shut-down of the engine. Ceramic coatings of yttria stabilized zirconia (ZrO2-Y2O3) were applied initially as a thermal barrier over coating to the NiCrAlY but were removed because of even greater spalling. Utilizing a vacuum plasma spraying process, bond coatings of NiCrAlY were applied in a low pressure atmosphere of argon/helium, producing significantly improved coating-to-blade bonding. The improved coatings showed no spalling after 40 MSFC burner rig thermal shock cycles, cycling between 1700 and -423 F. The current atmospheric plasma NiCrAlY coatings spalled during 25 test cycles. Subsequently, a process was developed for applying a durable thermal barrier coating of ZrO2-Y2O3 to the turbine blades of first stage high-pressure fuel turbopumps utilizing the vacuum plasma process. The improved thermal barrier coating has successfully passed 40 burner rig thermal shock cycles without spalling. Hot firing in an SSME turbine engine is scheduled for the blades. Tooling was installed in preparation for vacuum plasma spray coating other SSME hardware, e.g., the titanium main fuel valve housing (MFVH) and the fuel turbopump nozzle/stator.

Holmes, R. R.↗

NASA NTRS1989

Some composite bearing and seal materials for gas turbine applications - A review

A review is made of the selection and tribological testing of materials for high-temperature bearings and seals. The goal is to achieve good tribological properties over a wide range of temperatures because bearings and seals must be functional from low temperature start-up conditions on up to the maximum temperatures encountered during engine operation. Plasma sprayed composite coatings with favorable tribological properties from 25 to 900 C are discussed. The performance of these coatings in simple tribological bench tests is described. Examples are also given of their performance in high-speed sliding contact seals and as Stirling cylinder liner materials, and as backup lubricants for compliant foil gas bearings.

Sliney, Harold E.↗

NASA NTRS1990

Preliminary analysis of SSME baseline plume emissions

A review of current efforts to establish baseline emission levels from the SSME plume is presented. Recent data obtained under the Optical Plume Anomaly Detector program at the Technology Test Bed at MSFC is examined with an emphasis on interpretation of spectral and temporal features observed during nominal motor operation. In particular, the repeated appearance of Cr, Fe, Mn, Ca, and Li at engine startup and shutdown is discussed, and broadband attenuation due to scattering from water vapor is seen to complicate characterization of baseline levels. Also, emission from the combustion related specie OH, the underlying broadband continuum, and the Na impurity is discussed in relation to changes in Rated Power Level (RPL). Results from a theoretical spectral analysis of engine start-up activity is presented.

Wallace, T. L.↗

NASA NTRS1980

Equipment Failure Analysis

Tennessee Eastman uses NASTRAN to minimize lost production by pinpointing the causes of equipment failures and preventing recurrences. An example of the program's utility involves a large centrifugal fan which developed cracks during start-ups and shutdowns. This information prompted redesign of the fan. Tennessee Eastman has made extensive use of NASTRAN, both as failure analysis tool and as an aid in redesigning production hardware.

Source record↗

NASA NTRS1983

Motor power factor controller with a reduced voltage starter

A power factor type motor controller in which the conventional power factor constant voltage command signal is replaced during a starting interval with a graduated control voltage. The present invention adds to the three-phase system of pending application Ser. No. 199,765, filed Oct. 23, 1980, means for modifying the operation of the system for a motor start-up interval of 5 to 30 seconds. The modification is that of providing via ramp generator 174 an initial ramp-like signal which replaces a constant power factor signal supplied by potentiometer 70. The ramp-like signal is applied to terminal 40 where it is summed with an operating power factor signal from phase detectors 32, 34, and 36 to thereby obtain a control signal for ultimately controlling SCR devices 12, 14, and 16 to effect a gradual turn-on of motor 10. The significant difference of the present invention over prior art is that the SCR devices are turned on at an advancing rate with time responsive to the combination signal described rather than simply a function of a ramp-like signal alone. The added signal, the operating power factor signal, enables the production of a control signal which effectively eliminates a prior problem with many motor starting circuits, which is that of accompanying motor instabilities.

Nola, Frank J.↗

DOE OSTI2024

GeoBridge: Connecting Communities to Geothermal Information and Opportunities: Preprint

The geothermal community is well established with long-standing events, organizations, and tools that are known across the geothermal community. But many of these tools and resources are located behind pay walls, require memberships, or are otherwise difficult to find, especially for people looking to join the geothermal community. These barriers to access can prevent outsiders from discovering valuable geothermal resources, limiting the geothermal community's potential for collaboration with other communities, such as clean energy entrepreneurs looking to expand into geothermal energy. The Department of Energy's (DOE) GeoBridge serves to bring these communities together by acting as a single, publicly accessible, searchable portal that facilitates easy access to available geothermal knowledge and information. It works to expand and diversify the pool of geothermal stakeholders by providing in-roads to geothermal information and community resources. It helps build a stronger geothermal community; one inclusive of individuals and groups from a variety of different backgrounds, including potential investors and start-up companies looking to accelerate innovation in geothermal technologies. By linking communities to geothermal information, analysis and expertise, GeoBridge serves as a launch point, directing interested parties to existing data and tools, events, educational resources, STEM programs, permitting and regulatory information, and other resources that can be used to evaluate, promote, and discover geothermal opportunities.

access↗

DOE OSTI2025

GeoBridge: Connecting Communities to Geothermal Information and Opportunities

access↗

DOE OSTI2025

Reactors Section Presentation - INL, HPS Society 2025

The ongoing Nuclear Renaissance includes many next generation reactor designs and testing, this means translates to increased demand for Health Physicists. These opportunities are not limited to just reactors but the entire fuel cycle from mining and extraction from existing tailings, R&D support efforts at new start-up companies, to shielding modeling and design, to Recycling and Reprocessing, and eventually Decommissioning.

Health Physics↗

DOE OSTI2025

Development of Biological and Electrochemical Technologies for the Clean Extraction of Copper and Critical Materials from Low Grade Ores

As we transition toward renewable energy resources and electrification, there will be an increasing demand for critical materials, including copper. While copper is currently mined in the US, processing capacity is not sufficient, and intermediate mining products are shipped to Asia for further processing. The goal of this research was to develop a transformative hydrometallurgical process for the production of copper from low-grade ores that would eliminate the need for smelting and would increase the domestic processing capacity in the US, The project initially focused on the electrochemical reduction of copper concentrate using vanadium, followed by the biological oxidation to produce a stream compatible with existing solvent extraction and electrowinning operations. We discovered an efficient electrochemical process that could produce copper salts from concentrate without the need for biological oxidation, and this technology has been licensed and spun-off into a start-up company. The microbes involved in the current state-of-the-art bioleaching processes were genetically modified to introduced a number of new traits, including increased sulfur oxidation, salt-tolerance, and binding of other critical metals such as cobalt, molybdenum, rhenium, and the rare earth elements. The project was extended to also explore the electrochemical oxidation of copper concentrate using cerium which would potentially eliminate production of hydrogen sulfide that occurs with the reductive leaching process. This technology was found to have slower kinetics, however could it still be developed as an alternative process for domestic copper production and has been found to be applicable to other critical minerals.

42 ENGINEERING↗

DOE OSTI2025

Initial steady-state core simulation capability or thermal and pool-type molten salt reactors, coupling reactor physics, thermal-hydraulics, and evolving chemistry

This report presents the development and validation of an initial steady-state multiphysics capability for molten salt reactors (MSRs) under the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program in Fiscal Year 2025. The framework integrates neutronics, thermal-hydraulics, species transport, and thermochemistry to capture the coupled dynamics of liquid-fueled systems. Implementation and testing were performed on two representative designs: the Molten Salt Reactor Experiment (MSRE), a thermal-spectrum, channeled-flow reactor, and the Lotus Molten Salt Reactor (L-MSR), a fast-spectrum, pool-type reactor. The modeling suite employs Griffin for reactor physics and depletion, Pronghorn and SAM for thermal-hydraulics, Thermochimica for chemistry, and Saline for thermophysical properties, with benchmarking and validation carried out against historical MSRE data, experimental flow-loop measurements, and reference depletion calculations from Monte Carlo codes. The framework demonstrated the ability to reproduce key reactor behaviors including temperature feedback, reactivity losses, delayed neutron precursor transport, xenon poisoning, and redox potential evolution. The results confirm the feasibility and accuracy of the coupled models in predicting steady-state and selected transient MSR behaviors. This latter ones are used in this report as a proxy indicating that the steady-state models from which the transient starts are accurate. For MSRE, validation showed good agreement with pump start-up and natural circulation tests, while for the L-MSR, benchmarking confirmed hydraulic calibration and consistency of neutronics–thermal coupling. The tools also provided new insights into species transport, noble metal deposition, and salt solidification dynamics. On the Xenon transport front, the code is validated against the steady state Xenon poisoining measurement and showed good agreement with the experimental value. Identified areas for future work include advanced void transport modeling, three-dimensional simulations, improved alloy corrosion models, and tighter integration with high-fidelity Monte Carlo codes. These developments provide a foundation for high-fidelity MSR simulations that can support reactor design optimization, safety assessments, and long-term operational strategies.

42 - ENGINEERING↗

DOE OSTI2025

ECAR-8823 Rev 0 Structural Evaluation of the MARVEL Support Frame in Dry Critical Configuration

The purpose of this ECAR is to structurally evaluate the MARVEL reactor support frame during the dry critical (DryCrit) start-up testing. The ECAR includes evaluation of the DryCrit configuration for tip-over of the frame during a seismic event, floor loading of the frame on the MFC-720 (TREAT) operating floor, stress analysis of the adapter ring, and stress analysis of the frame itself for gravity and seismic loads.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗