SEARCH · Engineering Papers
Results for “stabilization method”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low-Frequency Stability Analysis of Inverter-Based Islanded Multiple-Bus AC Microgrids Based on Terminal Characteristics
For system planning of three-phase inverter-based islanded ac microgrids, the low frequency instability issue caused by interactions of inverter droop controllers is a major concern. When internal control information of procured commercial inverters is unknown, impedance-based small-signal stability criteria facilitate prediction of resonances in medium and high frequency ranges, but they usually assume the grid fundamental frequency as constant and thus they are incapable of analyzing the low-frequency oscillation of the fundamental frequency in islanded microgrids. Aiming at solving this issue, this paper proposes two stability analysis methods based on terminal characteristics of inverters and passive connection network including the dynamics of the fundamental frequency for analysis of low-frequency stability in islanded multiple-bus microgrids. Based on the Component Connection Method (CCM) to systematically separate inverters from the passive connection network, a general approach is developed to model the microgrid as a multiple-input-multiple-output (MIMO) negative feedback system in the common system d-q reference frame. By applying the generalized Nyquist stability criterion (GNC) to the return-ratio and return-difference matrices of the MIMO system model, the low-frequency stability related to the fundamental frequency can be analyzed using the measured terminal characteristics of inverters. Finally, analysis and simulation of a 37-bus microgrid verify the effectiveness of the proposed stability analysis methods.
Improving Analytic Methods for Studying Strategic Stability.
Abstract not provided.
Method and system to maintain electrolyte stability for all-iron redox flow batteries
Methods and systems are provided which maintain the positive and negative electrolyte pH and stability of a redox flow battery through the use of electrochemical rebalancing cells. The electrochemical cells may be activated by applying an electrical load to affect changes to the pH of the electrolytes. The use of the electrochemical cells improves long term performance stability redox flow batteries by decreasing and/or eliminating Fe(OH)3 precipitation formation.
Method and system to maintain electrolyte stability for all-iron redox flow batteries
Methods and systems are provided which maintain the positive and negative electrolyte pH and stability of a redox flow battery through the use of electrochemical rebalancing cells. The electrochemical cells may be activated by applying an electrical load to affect changes to the pH of the electrolytes. The use of the electrochemical cells improves long term performance stability redox flow batteries by decreasing and/or eliminating Fe(OH)3 precipitation formation.
Optimization Stability in Excited-State-Specific Variational Monte Carlo
Here, we investigate the issue of optimization stability in variance-based state-specific variational Monte Carlo, discussing the roles of the objective function, the complexity of wave function ansatz, the amount of sampling effort, and the choice of minimization algorithm. Using a small cyanine dye molecule as a test case, we systematically perform minimizations using variants of the linear method as both a standalone algorithm and in a hybrid combination with accelerated descent. We demonstrate that adaptive step control is crucial for maintaining the linear method's stability when optimizing complicated wave functions and that the hybrid method enjoys both greater stability and minimization performance.
Nodal Admittance Matrix Based Area Partition Method for Small-Signal Stability Analysis of Large-Scale Power Electronics Based Power Systems
In power electronics-based power systems (PEPSs), small-signal stability is an important factor for system design and operation, where the impedance-based approach is often used. However, unlike small-scale PEPSs with simple and straightforward impedance models, it would take much more efforts to derive the large-scale PEPSs impedance model, which is very complicated and sometimes may get wrong results due to the elimination of right-half plane (RHP) poles during the impedance aggregation process. To simplify the derivation procedure and analyze the small-signal stability of large-scale PEPSs, this paper proposes a nodal admittance matrix (NAM) based area partition method. In this method, the large-scale PEPS is divided into several sub-areas, and the stability is analyzed within the sub-area first, and then the interconnection stability among these sub-areas is analyzed. The proposed method is scalable and can help to locate the weakest areas/converters that may cause instability in the whole system. In this paper, the concept of the proposed method and its application to an example system are introduced. Experimental results are also given to validate the effectiveness of the proposed method.
Influence of Joule Heating on the Stability of High Temperature Irradiation-resistant Thermocouples
Development of in-core instrumentation is driven by the pursuit of safer, more economic energy production from the perspective of both existing nuclear reactors and Generation IV reactor designs. Idaho National Laboratory has developed high-temperature irradiation-resistant thermocouples (HTIR-TCs) for temperature sensing inside Generation IV nuclear reactors. These thermocouples are composed of phosphorus-doped niobium (Nb-P) and lanthana-doped molybdenum (Mo-LaO) thermoelements, an alumina (Al2O3) insulation, and a niobium sheath. HTIR-TCs require an initial heat treatment exceeding the maximum service temperature to stabilize the generated electromotive force (EMF) signal. The mechanism behind the stabilization of the HTIR-TCs through traditional heat treatment methods is understood; however, the traditional heat treatment method is expensive, time consuming, and results in a heterogeneous microstructure. Therefore, we investigated a rapid method for stabilization and microstructure homogeneity, through Joule heating. This work evaluates the impact of Joule heating on the thermoelements’ microstructures, chemical stability, and mechanical properties so as to determine the mechanisms by which stabilization of the EMF signal occurs. Accordingly, during the Joule heat treatment, a secondary Nb3P phase coarsened along the length of the Nb-P thermoelement, along with the formation of an interaction region at the Al2O3/niobium interface. The interaction between the alumina insulation and the Nb-P thermoelement was also observed within the Mo-LaO thermoelement. Joule heating induced stability within the generated HTIR-TC EMF signal via the formation of secondary phases within the Nb-P and the interaction between the alumina insulation and the thermoelements.
Simulations of single- and two-phase shock tubes and gravity-driven wave problems with the RELAP-7 nuclear reactor system analysis code
Propagation of pressure waves in single and two-phase flows is of key interest for nuclear safety analyses, reactor design, construction and life extension of nuclear reactors. In this work, we assess the capabilities of RELAP-7, the next-generation nuclear reactor system code, to solve single- and two-phase flows developing pressure waves. RELAP-7 is based on a 7-equation, two-phase flow model, with distinct phasic pressures. It is well established that these hyperbolic conservation laws can develop shocks and discontinuities and thus, require a stabilization numerical method. The all-Mach flow Entropy Viscosity Method (EVM) is now employed in RELAP-7 as a viscous stabilization approach. In this paper, we briefly describe the implementation of the EVM and use open-literature test cases that exhibit pressure waves to show that the entropy viscosity method performs adequately for these single- and two-phase cases.
Stability boundary and optimal operating parameter identification in milling using Bayesian learning
Here, this paper describes a novel Bayesian learning approach for stability boundary and optimal parameter identification in milling without the knowledge of the underlying tool dynamics or material cutting force coefficients. The paper is divided into two parts. First, a Bayesian learning method for stability lobe identification using test results is described. Each axial depth and spindle speed combination is characterized by a probability of stability which is updated using Bayes’ rule when a test result (stable or unstable) is made available. A novel likelihood function is defined which incorporates knowledge of the stability behavior. Numerical results show convergence to the analytical stability lobe diagram. Second, an adaptive experimental strategy to identify optimal operating parameters that maximize material removal rate is described. Numerical evaluation shows convergence to the optimal operating point with error less than 15 % within ten tests on average. The approach is validated using experimental results. Results show that the proposed method is an efficient and robust learning method to identify the stability lobe diagram and optimal operating parameters with a limited number of tests/data points.
Strong Stability Preserving Integrating Factor Two-Step Runge-Kutta Methods
In this report, problems with components that feature significantly different time scales, where the stiff time-step restriction comes from a linear component, implicit-explicit (IMEX) methods alleviate this restriction if the concern is linear stability. However, when nonlinear non-inner-product stability properties are of interest, such as in the evolution of hyperbolic partial differential equations with shocks or sharp gradients, linear inner-product stability is no longer sufficient for convergence, and so strong stability preserving (SSP) methods are often needed. Where the SSP property is needed, IMEX SSP Runge-Kutta (SSP-IMEX) methods have very restrictive time-steps. An alternative to SSP-IMEX schemes is to adopt an integrating factor approach to handle the linear component exactly and step the transformed problem forward using some time-evolution method. The strong stability properties of integrating factor Runge-Kutta methods were established in Isherwood et al. (SIAM J Numer Anal 56(6):3276–3307, 2018), where it was shown that it is possible to define explicit integrating factor Runge-Kutta methods that preserve strong stability properties satisfied by each of the two components when coupled with forward Euler time-stepping. It was proved that the solution will be SSP if the transformed problem is stepped forward with an explicit SSP Runge-Kutta method that has non-decreasing abscissas. However, explicit SSP Runge-Kutta methods have an order barrier of p=4, and sometimes higher order is desired. In this work we consider explicit SSP two-step Runge-Kutta integrating factor methods to raise the order. We show that strong stability is ensured if the two-step Runge-Kutta method used to evolve the transformed problem is SSP and has non-decreasing abscissas. We find such methods up to eighth order and present their SSP coefficients. Adding a step allows us to break the fourth order barrier on explicit SSP Runge-Kutta methods; furthermore, our explicit SSP two-step Runge-Kutta methods with non-decreasing abscissas typically have larger SSP coefficients than the corresponding one-step methods. A selection of our methods are tested for convergence and demonstrate the design order. We also show, for selected methods, that the SSP time-step predicted by the theory is a lower bound of the allowable time-step for linear and nonlinear problems that satisfy the total variation diminishing (TVD) condition. We compare some of the non-decreasing abscissa SSP two-step Runge-Kutta methods to previously found methods that do not satisfy this criterion on linear and nonlinear TVD test cases to show that this non-decreasing abscissa condition is indeed necessary in practice as well as theory. We also compare these results to our SSP integrating factor Runge-Kutta methods designed in Isherwood et al. (2018).
Analytical small-signal stability analysis of low-inertia power system frequency response considering secondary frequency regulation
Modern power systems are increasingly vulnerable to frequency instability as inverter-based resources (IBRs) replace synchronous machines and reduce system rotational inertia. Existing small-signal frequency stability assessment methods are either computationally intensive, relying on simulation-driven approaches, or lack analytical stability regions that explicitly account for secondary frequency response (SFR). This paper introduces new analytical frameworks that enable evaluation small-signal frequency stability while explicitly incorporating tunable IBR and SFR parameters. Using Kharitonov’s theorem with an overbounding approach, explicit small-signal stability criteria are derived. In addition, based on Białas’ criterion and Hurwitz matrix, analytical stability regions are established to reveal feasible design spaces for SFR and IBR parameters tuning. Extensive Matlab/Simulink-based simulations validate the accuracy and computational efficiency of the proposed methods, demonstrating that coordinated tuning of SFR and IBR parameters can substantially enhance system resilience. By bridging analytical rigor with practical tunability, this work provides an analytical framework for assessing small-signal frequency stability in low-inertia grids, supporting the real-time, scalable, and resilient operation of sustainable power systems.
SUPG stabilization for the nonconforming virtual element method for advection–diffusion–reaction equations
We present here the design, convergence analysis and numerical investigations of the nonconforming virtual element method with Streamline Upwind/Petrov–Galerkin (VEM-SUPG) stabilization for the numerical resolution of convection–diffusion–reaction problems in the convective-dominated regime. According to the virtual discretization approach, the bilinear form is split as the sum of a consistency and a stability term. The consistency term is given by substituting the functions of the virtual space and their gradients with their polynomial projection in each term of the bilinear form (including the SUPG stabilization term). Polynomial projections can be computed exactly from the degrees of freedom. The stability term is also built from the degrees of freedom by ensuring the correct scalability properties with respect to the mesh size and the equation coefficients. The nonconforming formulation relaxes the continuity conditions at cell interfaces and a weaker regularity condition is considered involving polynomial moments of the solution jumps at cell interface. Optimal convergence properties of the method are proved in a suitable norm, which includes contribution from the advective stabilization terms. Experimental results confirm the theoretical convergence rates.
High-order gradients with the shifted boundary method: An embedded enriched mixed formulation for elliptic PDEs
Here, we propose an extension of the embedded boundary method known as “shifted boundary method” to elliptic diffusion equations in mixed form (e.g., Darcy flow, heat diffusion problems with rough coefficients, etc.). Our aim is to obtain an improved formulation that, for linear finite elements, is at least second-order accurate for both flux and primary variable, when either Dirichlet or Neumann boundary conditions are applied. Following previous work of Nishikawa and Mazaheri in the context of residual distribution methods, we consider the mixed form of the diffusion equation (i.e., with Darcy-type operators), and introduce an enrichment of the primary variable. This enrichment is obtained exploiting the relation between the primary variable and the flux variable, which is explicitly available at nodes in the mixed formulation. The proposed enrichment mimics a formally quadratic pressure approximation, although only nodal unknowns are stored, similar to a linear finite element approximation. We consider both continuous and discontinuous finite element approximations and present two approaches: a non-symmetric enrichment, which, as in the original references, only improves the consistency of the overall method; and a symmetric enrichment, which enables a full error analysis in the classical finite element context. Combined with the shifted boundary method, these two approaches are extended to high-order embedded computations, and enable the approximation of both primary and flux (gradient) variables with second-order accuracy, independently on the type of boundary conditions applied. We also show that the primary variable is third-order accurate, when pure Dirichlet boundary conditions are embedded.
Spectral broadening and pulse shaping in the deep ultraviolet
Here, we report the generation and shaping of ∼20 femtosecond pulses in the deep ultraviolet (DUV). Our approach combines spectral broadening in a stretched hollow-core fiber with compression and shaping via an acousto-optic modulator-based pulse shaper. The pulse shaper allows for automatic compression, useful for in-air delivery of pulses to two-dimensional (2D) spectroscopy and other time-resolved experiments. Unlike previous DUV pulse generation schemes that lack phase stability, our method enables programmable generation of phase-locked pulse-pairs with attosecond-level stability. We demonstrate pulse characterization via self-diffraction frequency-resolved optical gating and dispersion scan methods in the DUV and validate performance through a pump-probe experiment resolving electronic dynamics on attosecond timescales.
Feedback Control Strategy for Transient Stability Application
Power systems are subjected to a wide range of disturbances during daily operations. Severe disturbances, such as a loss of a large generator, a three-phase bolted fault on a generator bus, or a loss of a transmission line, can lead to the loss of synchronism of a generator or group of generators. The ability of a power system to maintain synchronism during the few seconds after being subjected to a severe disturbance is known as transient stability. Most of the modern methods of controlling transient stability involve special protection schemes or remedial action schemes. These special protection schemes sense predetermined system conditions and take corrective actions, such as generator tripping or generation re-dispatch, in real time to maintain transient stability. Another method is the use of a real-time feedback control system to modulate the output of an actuator in response to a signal. This paper provides a fundamental evaluation of the use of feedback control strategies to improve transient stability in a power system. An optimal feedback control strategy that modulates the real power injected and absorbed by distributed energy-storage devices is proposed. Its performance is evaluated on a four-machine power system and on a 34-machine reduced-order model of the Western North American Power System. The result shows that the feedback control strategy can increase the critical fault clearing time by 60%, thereby improving the transient stability of the power system.
Small-Signal Analysis of Current-Limiting Grid-Forming Inverters
Grid-forming (GFM) inverters are equipped with a current limiter to protect the device during grid disturbances. Because the intervention of the current limiter can compromise the transient stability of the GFM inverter, various types of current limiter designs and additional frequency-stabilization control methods have been proposed in recent literature to aid in transient GFM inverter stability; however, the small-signal stability implications of adding these additional control blocks during, in particular, off-nominal conditions are not fully understood. To address this challenge, this paper presents a generic small-signal model of a GFM inverter that incorporates various types of current limiters and frequency stability-enhancing controls. With the proposed model, we analyze the root causes of inverter instability, which reveals two critical design trade-offs. First, due to current-limiter engagement caused by a disturbance, the GFM inverter dynamics are altered, which can lead to voltage oscillations. Second, additional frequency-stabilization controls can improve the small-signal stability of the GFM inverter, but at the cost of reduced power and voltage support to the grid. Comprehensive hardware experiments validate the theoretical concept and analysis. The findings in this work underscore the importance of incorporating both transient-response and small-signal dynamics requirements into the design procedure of GFM current limiters and frequency-stabilization controls.