Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solar cell efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Towards a 20 percent efficient silicon solar cell

A project is underway at the University of New South Wales aimed at producing a 20 percent efficient silicon solar cell. A prerequisite for obtaining such a significant increase in cell efficiency is the improvement of the open circuit voltage of these cells. Two techniques are described which have produced experimental devices with open circuit voltages of 690 mV or higher. These high voltage techniques have been combined with other high efficiency design features to produce silicon cells with independently measured energy conversion efficiencies in excess of 19 percent under standard terrestrial test conditions (direct beam AM1.5 spectrum, 100 mW/sq cm, 28 C).

Green, M. A.↗
NASA NTRS1980

Characterization of deliberately nickel-doped silicon wafers and solar cells

Microstructural and electrical evaluation tests were performed on nickel-doped p-type silicon wafers before and after solar cell fabrication. The concentration levels of nickel in silicon were 5 x 10 to the 14th power, 4 x 10 to the 15th power, and 8 x 10 to the 15th power atoms/cu cm. It was found that nickel precipitated out during the growth process in all three ingots. Clumps of precipitates, some of which exhibited star shape, were present at different depths. If the clumps are distributed at depths approximately 20 micron apart and if they are larger than 10 micron in diameter, degradation occurs in solar cell electrical properties and cell conversion efficiency. The larger the size of the precipitate clump, the greater the degradation in solar cell efficiency. A large grain boundary around the cell effective area acted as a gettering center for the precipitates and impurities and caused improvement in solar cell efficiency. Details of the evaluation test results are given.

Salama, A. M.↗
NASA NTRS1985

Recombination phenomena in high efficiency silicon solar cells

The dominant recombination phenomena which limit the highest efficiency attainable in silicon solar cells under terrestrial sunlight are reviewed. The ultimate achievable efficiency is limited by the two intrinsic recombination mechanisms, the interband Auger recombination and interband Radiative recombination, both of which occur in the entire cell body but principally in the base layer. It is suggested that an optimum (26%) cell design is one with lowly doped 50 to 100 micron thick base, a perfect BSF, and zero extrinsic recombination such as the thermal mechanism at recombination centers the Shockley-Read-Hall process (SRH) in the bulk, on the surface and at the interfaces. The importance of recombination at the interfaces of a high-efficiency cell is demonstrated by the ohmic contact on the back surface whose interface recombination velocity is infinite. The importance of surface and interface recombination is demonstrated by representing the auger and radiative recombination losses by effective recombination velocities. It is demonstrated that the three highest efficiency cells may all be limited by the SRH recombination losses at recombination centers in the base layer.

Sah, C. T.↗
NASA NTRS1978

Production technology for high efficiency ion implanted solar cells

Ion implantation is being developed for high volume automated production of silicon solar cells. An implanter designed for solar cell processing and able to properly implant up to 300 4-inch wafers per hour is now operational. A machine to implant 180 sq m/hr of solar cell material has been designed. Implanted silicon solar cells with efficiencies exceeding 16% AM1 are now being produced and higher efficiencies are expected. Ion implantation and transient processing by pulsed electron beams are being integrated with electrostatic bonding to accomplish a simple method for large scale, low cost production of high efficiency solar cell arrays.

Kirkpatrick, A. R.↗
NASA NTRS1985

Proceedings of the Flat-plate Solar Array Project Research Forum on High-efficiency Crystalline Silicon Solar Cells

The high-efficiency crystalline silicon solar cells research forum addressed high-efficiency concepts, surface-interface effects, bulk effects, modeling and device processing. The topics were arranged into six interactive sessions, which focused on the state-of-the-art of device structures, identification of barriers to achieve high-efficiency cells and potential ways to overcome these barriers.

Kachare, R.↗
NASA NTRS1994

High Efficiency InP Solar Cells from Low Toxicity Tertiarybutylphosphine

Large scale manufacture of phosphide based semiconductor devices by organo-metallic vapor phase epitaxy (OMVPE) typically requires the use of highly toxic phosphine. Advancements in phosphine substitutes have identified tertiarybutylphosphine (TBP) as an excellent precursor for OMVPE of InP. High quality undoped and doped InP films were grown using TBP and trimethylindium. Impurity doped InP films were achieved utilizing diethylzinc and silane for p and n type respectively. 16 percent efficient solar cells under air mass zero, one sun intensity were demonstrated with Voc of 871 mV and fill factor of 82.6 percent. It was shown that TBP could replace phosphine, without adversely affecting device quality, in OMVPE deposition of InP thus significantly reducing toxic gas exposure risk.

Hoffman, Richard W., Jr.↗
NASA NTRS1984

High-purity silicon crystal growth

Crystal growth parameter effects on minority carrier lifetime and solar cell efficiencies were investigated using high purity techniques such as float zoning. Study objectives include the following: (1) optimize dopants and minority carrier lifetime in FZ material for high efficiency silicon solar cell applications; (2) improve the understanding of lifetime degradation mechanisms (point defects, impurities, thermal history, surface effects, etc.), and (3) crystallographic defect characterization of float zone and ribbon crystals via X-ray topography.

Ciszek, T.↗
DOE OSTI2024

Mitigating Band Tailing in Kesterite Solar Absorbers: Ab Initio Quantum Dynamics

Open-circuit voltage deficits are limiting factors in kesterite solar cells. Addressing this issue by suppressing band tailing and nonradiative charge recombination is essential for enhancing the performance. We employ ab initio nonadiabatic molecular dynamics to elucidate the origin of band tailing and charge losses and propose a mitigation strategy. The simulations show that Cu–Zn disorder, associated with antisite defect clusters [Cu Zn +Zn Cu ], is a significant source of band tailing in kesterites, as evidenced by the much larger Urbach energy in disordered than ordered kesterites. Cu–Zn disorder gives rise to new sulfur-centered coordination polyhedra, increases structural inhomogeneity, changes electrostatic potential at sulfur centers, and shifts the S(3p) orbital energy. Differences in the S(3p)/Cu(3d) and S(3p)/Sn(5s) hybridization strengths and the S(3p) orbital energy shift reduce the band gap by 0.37 eV. Furthermore, Cu–Zn disorder enhances vibrational motion of sulfur anions and surrounding cations, increasing band gap fluctuations by 15 meV. The stronger electron–phonon interactions reduce charge carrier lifetimes and limit the kesterite solar cell efficiency. Partial substitution of Zn with Cd facilitates structural ordering and significantly suppresses band tailing, particularly in disordered systems. The improvement can be attributed to the larger atomic radius and mass of Cd, which weakens bonding around the anion, suppresses S-related vibrations within the covalent tetrahedra, and reduces nonadiabatic coupling, thereby increasing charge carrier lifetimes. The reported results establish the key influence of cation disorder on band tailing and reduced charge carrier lifetimes in kesterites and highlight cation disorder engineering as a strategy to achieve high-efficiency kesterite solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1986

High-efficiency silicon solar cells - Development, current issues and future directions

This paper provides a review of material, process, and design considerations that are essential for achieving high-efficiency silicon solar cells. It describes an approach that resulted in 18.0-18.5-percent-efficient cells on low-resistivity float-zone silicon material. It is shown experimentally that a combination of surface passivation and double-layer antireflection coating can provide 2-3 percent (absolute) improvement in cell efficiency provided the material, process and cell design are carefully selected.

Rohatgi, A.↗
NASA NTRS1985

High-efficiency silicon solar cells

Fabrication and characterization of high-efficiency metal insulator, n-p (MINP) cells is described. Particular attention was paid to development of measurement methods for surface recombination and density of surface states. A modified Rosier test structure was used successfully for density of surface states. Silicon oxide and silicon nitride passivants were studied. Heat treatment after plasma enhanced chemical vapor deposition (CVD) of silicon nitride was shown to be beneficial. A more optimum emitter concentration profile was modeled.

Olsen, L. C.↗
NASA NTRS1993

Study of the Staebler-Wronski degradation effect in a-Si:H based p-i-n solar cell

Conversion of solar energy into electricity using environmentally safe and clean photovoltaic methods to supplement the ever increasing energy needs has been a cherished goal of many scientists and engineers around the world. Photovoltaic solar cells on the other hand, have been the power source for satellites ever since their introduction in the early sixties. For widespread terrestrial applications, however, the cost of photovoltaic systems must be reduced considerably. Much progress has been made in the recent past towards developing economically viable terrestrial systems, and the future looks highly promising. Thin film solar cells offer cost reductions mainly from their low processing cost, low material cost, and choice of low cost substrates. These are also very attractive for space applications because of their high power densities (power produced per kilogram of solar cell pay load) and high radiation resistance. Amorphous silicon based solar cells are amongst the top candidates for economically viable terrestrial and space based power generation. Despite very low federal funding during the eighties, amorphous silicon solar cell efficiencies have continually been improved - from a low 3 percent to over 13 percent now. Further improvements have been made by the use of multi-junction tandem solar cells. Efficiencies close to 15 percent have been achieved in several labs. In order to be competitive with fossil fuel generated electricity, it is believed that module efficiency of 15 percent or cell efficiency of 20 percent is required. Thus, further improvements in cell performance is imperative. One major problem that was discovered almost 15 years ago in amorphous silicon devices is the well known Staebler-Wronski Effect. Efficiency of amorphous silicon solar cells was found to degrade upon exposure to sunlight. Until now their is no consensus among the scientists on the mechanism for this degradation. Efficiency may degrade anywhere from 10 percent to almost 50 percent within the first few months of operation. In order to improve solar cell efficiencies, it is clear that the cause or causes of such degradation must be found and the processing conditions altered to minimize the loss in efficiency. This project was initiated in 1987 to investigate a possible link between metallic impurities, in particular, Ag, and this degradation. Such a link was established by one of the NASA scientists for the light induced degradation of n+/p crystalline silicon solar cells.

Naseem, H. A.↗
NASA NTRS2005

Recent Progress in CuInS2 Thin-Film Solar Cell Research at NASA Glenn

The National Aeronautics and Space Administration (NASA) is interested in developing low-cost highly efficient solar cells on light-weight flexible substrates, which will ultimately lower the mass-specific power (W/kg) of the cell allowing extra payload for missions in space as well as cost reduction. In addition, thin film cells are anticipated to have greater resistance to radiation damage in space, prolonging their lifetime. The flexibility of the substrate has the added benefit of enabling roll-to-roll processing. The first major thin film solar cell was the "CdS solar cell" - a heterojunction between p-type CuxS and n-type CdS. The research on CdS cells started in the late 1950s and the efficiency in the laboratory was up to about 10 % in the 1980s. Today, three different thin film materials are leading the field. They include amorphous Si, CdTe, and Cu(In,Ga)Se2 (CIGS). The best thin film solar cell efficiency of 19.2 % was recently set by CIGS on glass. Typical module efficiencies, however, remain below 15 %.

Jin, M. H.-C.↗
DOE OSTI2024

Halogenated Dibenzo[ f , h ]quinoxaline Units Constructed 2D‐Conjugated Guest Acceptors for 19% Efficiency Organic Solar Cells

Abstract Halogenation of Y‐series small‐molecule acceptors (Y‐SMAs) is identified as an effective strategy to optimize photoelectric properties for achieving improved power‐conversion‐efficiencies (PCEs) in binary organic solar cells (OSCs). However, the effect of different halogenation in the 2D‐structured large π‐fused core of guest Y‐SMAs on ternary OSCs has not yet been systematically studied. Herein, four 2D‐conjugated Y‐SMAs (X‐QTP‐4F, including halogen‐free H‐QTP‐4F, chlorinated Cl‐QTP‐4F, brominated Br‐QTP‐4F, and iodinated I‐QTP‐4F) by attaching different halogens into 2D‐conjugation extended dibenzo[ f , h ]quinoxaline core are developed. Among these X‐QTP‐4F, Cl‐QTP‐4F has a higher absorption coefficient, optimized molecular crystallinity and packing, suitable cascade energy levels, and complementary absorption with PM6:L8‐BO host. Moreover, among ternary PM6:L8‐BO:X‐QTP‐4F blends, PM6:L8‐BO:Cl‐QTP‐4F obtains a more uniform and size‐suitable fibrillary network morphology, improved molecular crystallinity and packing, as well as optimized vertical phase distribution, thus boosting charge generation, transport, extraction, and suppressing energy loss of OSCs. Consequently, the PM6:L8‐BO:Cl‐QTP‐4F‐based OSCs achieve a 19.0% efficiency, which is among the state‐of‐the‐art OSCs based on 2D‐conjugated Y‐SMAs and superior to these devices based on PM6:L8‐BO host (17.70%) and with guests of H‐QTP‐4F (18.23%), Br‐QTP‐4F (18.39%), and I‐QTP‐4F (17.62%). The work indicates that halogenation in 2D‐structured dibenzo[ f , h ]quinoxaline core of Y‐SMAs guests is a promising strategy to gain efficient ternary OSCs.

14 SOLAR ENERGY↗
NASA NTRS1995

Advanced solar panel designs

This paper describes solar cell panel designs that utilize new hgih efficiency solar cells along with lightweight rigid panel technology. The resulting designs push the W/kg and W/sq m parameters to new high levels. These new designs are well suited to meet the demand for higher performance small satellites. This paper reports on progress made on two SBIR Phase 1 contracts. One panel design involved the use of large area (5.5 cm x 6.5 cm) GaAs/Ge solar cells of 19% efficiency combined with a lightweight rigid graphite fiber epoxy isogrid substrate configuration. A coupon (38 cm x 38 cm) was fabricated and tested which demonstrated an array specific power level of 60 W/kg with a potential of reaching 80 W/kg. The second panel design involved the use of newly developed high efficiency (22%) dual junction GaInP2/GaAs/Ge solar cells combined with an advanced lightweight rigid substrate using aluminum honeycomb core with high strength graphite fiber mesh facesheets. A coupon (38 cm x 38 cm) was fabricated and tested which demonstrated an array specific power of 105 W/kg and 230 W/sq m. This paper will address the construction details of the panels and an a analysis of the component weights. A strawman array design suitable for a typical small-sat mission is described for each of the two panel design technologies being studied. Benefits in respect to weight reduction, area reduction, and system cost reduction are analyzed and compared to conventional arrays.

Ralph, E. L.↗
DOE OSTI2024

High-Efficiency Recycled Silicon Solar Cell

The project, High-Efficiency Recycled Silicon Solar Cell, addresses the critical challenge of end-of-life (EoL) photovoltaic (PV) waste, which is expected to reach 78 million tons by 2050. Traditional recycling methods for recovering valuable materials like silver from silicon solar cells are inefficient, environmentally harmful, and economically unfeasible. Therefore, presently waste solar cells end up as landfills. This project aimed to develop a green, scalable, laser-based method for silver recovery, avoiding hazardous chemicals and minimizing operational costs. This research contributes to the circular economy in the renewable energy sector by enhancing material recovery from PV waste.

14 SOLAR ENERGY↗
DOE OSTI2026

15.3% AM1.5G Efficiency GaAs Solar Cells Fabricated via an Epitaxy-Free Process

Here, we report simple and potentially low-cost techniques for creating high-quality n-type gallium arsenide (GaAs) and GaAs p/n junctions and fabricate GaAs p/n junction solar cells. Detailed-balance modeling suggests that 20% AM1.5G efficiency p/n homojunction devices may be possible if the surface doping concentration can be limited to values less than ∼ 5 × 10 19 cm −3 . Our process exploits an open-tube, vapor-phase, deposition-free, zinc diffusion technique for forming p-type layers in melt-grown n-GaAs substrates that results in sheet resistances less than 1 kΩ/$\square$. In addition, we have improved the minority carrier diffusion lengths of melt-grown GaAs from less than one micron to over five microns using an open-tube, vacuum-free, annealing process which reduces the density of EL2 midgap defects. Finally, we have combined these advances to fabricate epitaxy-free, GaAs solar cells with a validated AM1.5G efficiency of 15.3%.

14 SOLAR ENERGY↗
NASA NTRS1985

The status of silicon ribbon growth technology for high-efficiency silicon solar cells

More than a dozen methods have been applied to the growth of silicon ribbons, beginning as early as 1963. The ribbon geometry has been particularly intriguing for photovoltaic applications, because it might provide large area, damage free, nearly continuous substrates without the material loss or cost of ingot wafering. In general, the efficiency of silicon ribbon solar cells has been lower than that of ingot cells. The status of some ribbon growth techniques that have achieved laboratory efficiencies greater than 13.5% are reviewed, i.e., edge-defined, film-fed growth (EFG), edge-supported pulling (ESP), ribbon against a drop (RAD), and dendritic web growth (web).

Ciszek, T. F.↗