Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “renewables in mining”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Switching kinetics in ferroelectric zinc magnesium oxide thin films

The switching kinetics of RF-magnetron reactively sputtered ~200 nm thick Zn 1-x Mg x O (ZMO) ferroelectric thin films with x = 0.41 and x = 0.27 prepared on Pt/Ti/SiO 2 /Si substrates were studied at applied fields near the coercive fields, ranging from 3.4 to 5.1 MV cm -1 , and at temperatures ranging from room temperature to 100 °C. Polarization reversal in ZMO followss the Kolmogorov-Avrami-Ishibashi kinetics model for nucleation and growth at applied fields near the coercive field, and obeys an individual column switching (ICS) model at higher applied fields required to switch most of the spontaneous polarization. Switching in the high-applied field regime can be described using either the Gaussian or inverse gamma distribution functions depending on the mole fraction of magnesium in the film. The switching current transients of the high-Mg content ZMO film (x = 0.41) are always bi-modal, whereas the low Mg composition film (x = 0.27) is described by the Gaussian distribution initially following wake-up, and becomes bimodal with continued cycling. Rayleigh-like behavior of the dielectric constant revealed a simultaneous increase of the irreversible and decrease of the reversible contributions to the dielectric constant, which was ascribed to an increase in the density of mobile domain walls with cycling and resulted in faster switching.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

The dual role of iron in alkaline water electrolysis: A friend or a foe?

Trace iron (Fe) impurities pose a challenge in alkaline water electrolysis (AWE) and can significantly impact long-term performance, yet their comprehensive system-level effects remain poorly understood. Here, we present the mechanistic roles of Fe in AWE, using combined rotation disk electrode studies, zero-gap cell measurements, and durability tests up to 1,000 h. Fundamental electrochemistry shows that Fe deposition proceeds through a solution-mediated pathway, with dendritic growth triggered under specific mass-transport and potential conditions. In single-cell operation, Fe incorporation substantially enhances nickel (Ni)-based anode activity by forming highly active Ni-Fe oxyhydroxides, while cathodic Fe forms either thin films or dendrites, depending on potential, surface morphology, and electrolyte distribution. Although dendrites do not degrade hydrogen evolution performance up to 1,000 h, they reveal partial intrusion into the separator, indicating a potential durability risk. We identify five governing factors controlling Fe dendrite formation and provide design principles for impurity-resilient AWE systems.

Lyu, Xiang [ORNL] (ORCID:0000000208673248)↗
DOE OSTI2025

Scaling deep learning for material imaging with a pseudo 3D model for domain transfer

The recent introduction of deep learning methods for image processing has greatly advanced the characterization of materials using three-dimensional (3D) X-ray imaging techniques. However, deep learning models often have difficulty performing consistently across images owing to unavoidable variations in imaging conditions, which create inconsistencies even for the same material. As a result, networks must frequently be retrained for new datasets, limiting their applicability and generalization. Thus, it is critical to reduce the variations between images to enable a single model to process multiple datasets. Herein, we introduce P3T-Net, a pseudo-3D domain transfer network that transfers diverse 3D images into a uniform domain before processing using deep learning models. Remarkably, P3T-Net enables the reuse of previously trained networks for processing new images and considerably reduces the computational cost of transferring 3D images across domains. These unique capabilities were demonstrated in the following scenarios: (i) image enhancement of fast scans for geological rock and hydrogen fuel cells, (ii) enhancement of images to match the quality of multi-source imaging for lithium-ion batteries, (iii) accurate segmentation of images captured under different conditions, and (iv) tera-scale 3D transfer (10 11 voxels) on a single GPU. Overall, the proposed approach addresses cross-domain inconsistencies across various materials and conditions, thereby enabling more robust and generalizable deep learning solutions for a wide range of material imaging tasks.

25 ENERGY STORAGE↗
DOE OSTI2025

Mind the gap: Bridging the divide between AI aspirations and the reality of autonomous microscopy

What does materials science look like in the “Age of Artificial Intelligence?” Each material’s domain—synthesis, characterization, and modeling—has a different answer to this question, motivated by unique challenges and constraints. This work focuses on the tremendous potential of autonomous characterization within electron microscopy. We present our recent advancements in developing domain-aware, multimodal models for microscopy analysis capable of describing complex atomic systems. We then address the critical gap between the theoretical promise of autonomous microscopy and its current practical limitations, showcasing recent successes while highlighting the necessary developments to achieve robust, real-world autonomy.

2D materials↗
DOE OSTI2026

Generation of Rare Earth Metals from Rare Earth Oxide Using Microwave Plasmas

The overarching goal of the proposed project is to develop a simple, energy-saving, high-selectivity technology for efficiently converting rare-earth oxides (REOs) to rare-earth metals (RE-metals) using microwave plasma under low temperature and inexpensive H 2 and N 2 . The project was managed and led by Dr. Maohong Fan at the University of Wyoming. The collaborating institutions include Ames Lab and Colorado School of Mines. The industrial collaboration entity is Eutectix, LLC. The use of hydrogen to reduce rare earth oxides has many advantages, as it is renewable and does not produce harmful emissions during metal production. Also, it avoids the use of carbon and the emission of CO 2 . Nd 2 O 3 treated with hydrogen plasma shows new peaks alongside those of Nd 2 O 3 . Some of these peaks are close to (28.4, 29.4, 30.5, 32.3, 36.6, 42.1, 48.9, 50.08, 55.1, 59.05, 59.64, 60.68, 62.5, 63.25), which may be related to elemental Nd.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Materials for the Photoluminescence-Based Detection of Economically Critical Metals

Critical metals, such as rare earth elements (REEs), cobalt, lithium, aluminum, nickel, and others, are essential to advanced technologies and renewable energy in particular. Widespread global adoption of renewable energy technologies has spurred dramatic demand increases for these metals; however, the global supply of these metals is highly monopolistic and conventional mining poses economic and environmental challenges. As a result, there is increasing interest in domestic production from alternative resources such as coal and its utilization byproducts. Slow and expensive characterization costs remain a significant barrier for domestic production. Here, luminescent sensing materials and platforms are presented that provide an alternative to the current state-of-the-art characterization methods; highly sensitive and selective sensing materials for cobalt, aluminum, and rare earth elements are presented, as well as compact, inexpensive platforms capable of analyzing signal from these materials for rapid characterization of critical metal content.

Crawford, Scott↗
DOE OSTI2024

Materials for the Photoluminescence-Based Detection of Economically Critical Metals

Critical metals, such as rare earth elements (REEs), cobalt, lithium, aluminum, nickel, and others, are essential to advanced technologies and renewable energy in particular. Widespread global adoption of renewable energy technologies has spurred dramatic demand increases for these metals; however, the global supply of these metals is highly monopolistic and conventional mining poses economic and environmental challenges. As a result, there is increasing interest in domestic production from alternative resources such as coal and its utilization byproducts. Slow and expensive characterization costs remain a significant barrier for domestic production. Here, luminescent sensing materials and platforms are presented that provide an alternative to the current state-of-the-art characterization methods; highly sensitive and selective sensing materials for cobalt, aluminum, and rare earth elements are presented, as well as compact, inexpensive platforms capable of analyzing signal from these materials for rapid characterization of critical metal content.

Crawford, Scott↗
DOE OSTI2023

Urban mining from biomass, brine, sewage sludge, phosphogypsum and e-waste for reducing the environmental pollution: Current status of availability, potential, and technologies with a focus on LCA and TEA

We discuss how rapid industrialization, improved standards of living, growing economies and ever-increasing population has led to the unprecedented exploitation of the finite and non-renewable resources of minerals in past years. It was observed that out of 100 BMT of raw materials processed annually only 10% is recycled back. This has resulted in a strenuous burden on natural or primary resources of minerals (such as ores) having limited availability. Moreover, severe environmental concerns have been raised by the huge piles of waste generated at landfill sites. To resolve these issues, ‘Urban Mining’ from waste or secondary resources in a Circular Economy’ concept is the only sustainable solution. The objective of this review is to critically examine the availability, elemental composition, and the market potential of the selected secondary resources such as lignocellulosic/algal biomass, desalination water, sewage sludge, phosphogypsum, and e-waste for minerals sequestration. This review showed that, secondary resources have potential to partially replace the minerals required in different sectors such as macro and microelements in agriculture, rare earth elements (REEs) in electrical and electronics industry, metals in manufacturing sector and precious elements such as gold and platinum in ornamental industry. Further, inputs from the selected life cycle analysis (LCA) & techno economic analysis (TEA) were discussed which showed that although, urban mining has a potential to reduce the greenhouse gaseous (GHG) emissions in a sustainable manner however, process improvements through innovative, novel and cost-effective pathways are essentially required for its large-scale deployment at industrial scale in future.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Supercritical preparation of doped (111) facetted nickel oxide for the oxygen evolution reaction

Green hydrogen is of great interest as a replacement for traditional fossil fuels in a variety of energy applications. However, due to the poor kinetics present in the oxygen evolution reaction (OER) half-reaction, nanostructured catalysts are needed to reduce the reaction overpotential. Nickel oxide has previously been shown to be a promising alternative to expensive Pt-group based catalysts for the OER in alkaline media. Herein, facetted NiO nanosheets have been doped with Fe, Mn, or Co to reduce its catalytic overpotential for the OER. A supercritical synthesis process was used to promote the mass transport of the reactants while preserving catalytic surface area. Microscopy, diffraction, spectroscopy, and adsorption techniques were used to understand the morphological changes resulting from the inclusion of each dopant, as well as characterize the surface chemistry presented by the doped (111) facet. The pH was found to affect the properties of mixing due to difference in hydrolysis rates and catalysis of the hydrolysis/condensation. The dopants exhibited distinct effects on OER activity: Mn increased the overpotential to 742 mV vs. RHE, while Co and Fe reduced it to 502 mV and 457 mV, respectively. In summary, a straightforward and novel synthesis method is presented to prepare doped NiO(111) nanosheets, and their surface characteristics are explored to understand their varied electrochemical performances.

08 HYDROGEN↗
DOE OSTI2025

Component Identification of Solid Biomass Fuels Using Reflected Light Microscopy: Interlaboratory Study 2

As nations transition toward sustainable energy systems, biomass has become a vital component of global energy portfolios. Derived from organic materials such as wood, agricultural residues, forestry byproducts, and organic waste, biomass is a renewable energy source with significant environmental and economic benefits. Responsible biomass energy production can improve waste management, reduce emissions of greenhouse gases, and mitigate environmental pollution. However, as the diversity of biomass-derived fuels increases, robust quality assessment methods are essential to ensure their efficiency, safety, and minimal environmental impact. Reflected light microscopy (RLM) is one such technique with the potential to complement conventional physico-chemical analyses by enabling a rapid identification of material constituents and impurities. To refine this methodology and evaluate the reproducibility of solid biomass component identification using RLM, an interlaboratory study (ILS) was conducted. The study involved the recognition of 58 components across 45 photomicrographs, with the participation of 65 scientists and students from 25 countries. The participants faced high difficulty identifying some of the marked components, and as a result, the percentage of correct answers ranged from 19.0 % to 98.3 %, with an average correct identification rate of 62.7 %. The most challenging aspects of the identification process included distinguishing between woody and non-woody (agro) biomass, accurately identifying petroleum-derived materials, and differentiating agro biomass from inorganic matter. The results suggest that while RLM is an important tool for characterizing solid biomass, further development of methodology guidelines and training are necessary to enhance its effectiveness. Future research should prioritize preparing detailed, image-rich, microscopic morphological descriptions of biomass fuel components, which could improve the accuracy and reliability of using RLM in biomass fuel characterization.

09 BIOMASS FUELS↗
DOE OSTI2022

A portable fiber optic sensor for the luminescent sensing of cobalt ions using carbon dots

Cobalt is critical to energy-relevant technologies, and demand for cobalt will increase significantly with growing global adoption of renewables. However, supply chain stability is threatened by economic and geopolitical factors, incentivizing domestic cobalt production from alternative resources such as coal, coal utilization byproducts (e.g., ash, acid mine drainage) and electronic waste. Rapid, inexpensive, and portable characterization techniques are needed to reduce production costs associated with cobalt prospecting and process monitoring. Here, in this research, we develop a compact, portable fiber optic luminescent probe for cobalt using phosphorus and nitrogen co-doped carbon dots as the sensing material. The carbon dot emission overlaps well with the cobalt absorption band at ~510 nm, leading to a selective decrease in emission as a function of cobalt concentration. The system responds nearly instantly to the presence of cobalt, with detection limits of 0.7 and 3.5 ppm in water and pH 1.68 buffer, respectively, providing comparable performance to a commercial spectrometer at a significantly lower cost. Moreover, the sensor is selective for cobalt in the presence of 13 of the most common metal ions encountered in coal utilization byproducts and is responsive to cobalt when spiked into an acid mine drainage leachate sample, highlighting the sensor's potential for real-world deployment in challenging matrices. In addition, integrating the carbon dots with a filter paper substrate produced ‘test strip’ sensors that exhibited a selective and sensitive visual response to cobalt using a handheld UV lamp. Taken together, the sensing system represents a significant step forward in the development of low-cost practical sensors for high-value metals in complex streams.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Assessment of Technoeconomic Opportunities in Automation for Nuclear Microreactors

Achieving full decarbonization of all economic sectors remains a challenge, especially in niche markets. For example, remote communities and industrial or mining activities detached from the main electric grid heavily rely on fossil fuels, similar to urban and industrial microgrids with combined heat and power needs. A combination of renewables and energy storage is often not suitable due to cost, reliability, intermittency, and large storage requirements. Small nuclear reactors with a flexible purpose could serve these applications. Microreactors (MR) are a class of reactors that are compact, factory manufactured, transportable, and self-regulating. Typically, they generate much less power than their large reactor counterparts. The main advantages of microreactors include the versatile nature of the energy produced, the reliability of supply, and freedom from having to transport and store large quantities of fuels on-site, coupled with the absence of dependence on an electrical grid. A strong business case is needed to move from the microreactor prototype to the commercialization phase. In fact, fossil fuels are still relatively inexpensive, and in the near term, carbon credits will be available to virtually compensate for emissions. For microreactors, one of the main costs in operation and maintenance (O&M) is their staffing levels. In this study, we investigate how to optimize the number (and thus the cost) of workers, moving from a traditional, fully manned, on-site personnel approach to an unmanned, remote personnel approach. We examine four different staffing models that can be implemented as the technology matures and evolves. We estimate the staffing needs of each model and build a business case to justify the substitution of on-site personnel with adequate technologies. To do so, we propose a cost model to quantify potential cost reductions from automating O&M activities. The model accounts for both the reduction in cost derived from the reduced number of full-time-equivalent (FTE) employees and the increase in cost derived from the need to buy new control hardware as needed. Applying the cost model that we created to different scenarios, an on-site O&M cost reduction exceeding 80% can be expected. Additionally, we found that it is more impactful to focus on automating routine O&M tasks rather than attempting to automate transient management (shutdowns, restarts, monitoring condition deviations). In fact, transients typically account for less than 1% of the total FTE time spent on the reactors.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

PACE: Producing Algae for Co-Products and Energy (Final Report)

The PACE (Producing Algae for Co-Products and Energy) consortium was comprised of scientists from national laboratories (Los Alamos National Laboratory, Pacific Northwest National Laboratory), research institutions (New Mexico Consortium), academic institutions (Arizona State University, Colorado School of Mines, Colorado State University, Washington State University) and private companies (Reliance Industries, PanPacific, Genifuel and Sonosop) dedicated to making process improvements in algal biotechnology, with an emphasis on renewable fuels and co-products from biomass. The scope of work was focused on improving algal cultivation and processing to achieve an overall energy return on investment (EROI) >3, a carbon index less than 55 grams carbon dioxide per megajoule (gCO2/MJ) and a nearly two-fold reduction in fuel cost to ≤$5 per gallon of gasoline equivalent (gge). The PACE project was originally focused on using two strains of Chlorella sorokiniana (Cs1412 and Cs1230), but later grew to encompass marine strains of Nannochloropsis and algal production strains from Reliance Industries Limited (RIL).

09 BIOMASS FUELS↗
DOE OSTI2024

Enhanced Resistance Pines for Improved Renewable Biofuel and Chemical Production (Technical Report)

We completed phenotyping constitutive and inducible oleoresin flow across two seasons, constitutive resin canal number and density and wood terpene content in our ADEPT2 and CCLONES populations. We completed genetic association between 19 oleoresin phenotypes and a total of 523,192 SNP markers from ADEPT2 and 13,883 SNP markers in CCLONES using four mixed linear models. A total of 293 significant SNPs (FDR = 0.20) were identified. We used the MENTOR tool to mine mechanistic connections from a multiplex network constructed from poplar multi-omic data to construct a conceptual model for a subset of these significant SNPs. Our model contains 6 transcriptional regulators in addition to 3 monoterpene synthases. To generate more lines of evidence for these significant SNPs, we completed a time course RNAseq experiment after inducing vascular zone cells to differentiate into new resin canals with a methyl jasmonate treatment, a single nuclei RNAseq that identified differentiating resin canal epithelial cells and are completing analysis for a QTL study in a hybrid pine population. The time course identified 4634 significantly down and 1890 significantly up regulated transcripts after treatment with methyl jasmonate, an inducer of new resin canal formation in the vascular cambial meristem. To analyze this large set of differentially regulated genes, we created a predictive expression network and analyzed it with random walk restart using 6 seed genes coding for transcription factors regulating xylem differentiation in poplar. Of the top ranked 200 transcripts, 119 transcripts were significant differentially expressed supporting these transcripts as potential candidates regulating resin canal formation. Analysis of single nuclei sequencing of shoot tips that contain differentiating resin canals, identified 10 clusters. One cluster was highly enriched in transcripts coding for 9 of the enzymes in the MEP pathway 3 prenyl synthetases, and 3 monoterpene synthases strongly suggesting that this cluster represents resin canal epithelial cells. We are mining the additional transcripts to create a trajectory analysis. In summary, we have identified > 10 novel genes that are strongly supported candidates for further analysis in breeding lines and for genetic engineering over- and under- expressing lines to increase wood terpene content to improve resistance to insect and fungal pathogens while simultaneously increasing terpene supplies for renewable chemicals and biofuels.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Development of Luminescent Materials and Instrumentation for Critical Mineral Discovery and Monitoring

Presentation discussing career paths in chemistry as well as how chemical research is applied to address real-world problems. Here, a variety of different materials (metal-organic frameworks, carbon dots, thin films, etc.) are used as luminescent sensors to detect trace quantities of economically critical metals, which are used in applications ranging from renewable energy to national defense. In an application particularly relevant to Western Pennsylvania, the sensor technologies are deployed in coal utilization byproducts including fly ash leachates and acid mine drainage. Taken together, this research presents an exciting path towards reducing the characterization costs associated with metals prospecting and process monitoring, facilitating domestic production of these metals.

analytical chemistry↗
DOE OSTI2022

Accelerating manufacturing for biomass conversion via integrated process and bench digitalization: a perspective

We present a perspective for accelerating biomass manufacturing via digitalization. We summarize the challenges for manufacturing and identify areas where digitalization can help. A profound potential in using lignocellulosic biomass and renewable feedstocks, in general, is to produce new molecules and products with unmatched properties that have no analog in traditional refineries. Discovering such performance-advantaged molecules and the paths and processes to make them rapidly and systematically can transform manufacturing practices. Furthermore, we discuss retrosynthetic approaches, text mining, natural language processing, and modern machine learning methods to enable digitalization. Laboratory and multiscale computation automation via active learning are crucial to complement existing literature and expedite discovery and valuable data collection without a human in the loop. Such data can help process simulation and optimization select the most promising processes and molecules according to economic, environmental, and societal metrics. We propose the close integration between bench and process scale models and data to exploit the low dimensionality of the data and transform the manufacturing for renewable feedstocks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

UNrealized Critical Lanthanide Extraction from Sea Algae Mining (UNCLE SAM)

The UNCLE-SAM project, under the Biotechnologies to Ensure a Robust Supply of Critical Materials for Clean Energy program, examined the biomining applications of seaweeds for sustainable, domestic production of critical mineral feedstocks. The ocean is a vast reserve of mineralogical wealth including rare earth elements (REEs) and platinum group metal (PGMs). These elements, categorized as “critical minerals”, are used in telecommunication devices, lasers, LED lighting, turbine generators, electric car motors, jet engine alloys, and many other applications. These critical elements are increasingly vital to a thriving, efficient and sustainable society. However, only a few countries in the global market currently produce and export REEs, leading to potential geopolitical supply disruptions. Marine macroalgae, often referred to as seaweeds, bioconcentrate critical minerals from seawater, including REEs and PGMs. Marine algae cultivation can generate a significant amount of biomass with minimal freshwater, fertilizer, and land requirements. In summary, the UNCLE-SAM project successfully evaluated the technological feasibility for marine macroalgal cultivation as a feedstock for critical minerals, explored the biological capacity of different seaweeds to provide economically relevant domestic mineral production, assessed processing techniques for thermal co-conversion of seaweeds into renewable fuel and mineral feedstocks, and executed techno-economic and lifecycle assessments for identifying the most critical gaps in our current understanding to move the technology into commercially relevant deployment. Further development of this technology could transform the bioproduct and REE mining industries and catalyze the development of a more sustainable future.

09 BIOMASS FUELS↗
DOE OSTI2023

Unrealized Critical Lanthanide Extraction from Sea Algae Mining (UNCLE SAM): Domestic production of critical minerals from seawater

The UNCLE-SAM project, under the Biotechnologies to Ensure a Robust Supply of Critical Materials for Clean Energy program, examined the biomining applications of seaweeds for sustainable, domestic production of critical mineral feedstocks. The ocean is a vast reserve of mineralogical wealth including rare earth elements (REEs) and platinum group metal (PGMs). These elements, categorized as “critical minerals”, are used in telecommunication devices, lasers, LED lighting, turbine generators, electric car motors, jet engine alloys, and many other applications. These critical elements are increasingly vital to a thriving, efficient and sustainable society. However, only a few countries in the global market currently produce and export REEs, leading to potential geopolitical supply disruptions. Marine macroalgae, often referred to as seaweeds, bioconcentrate critical minerals from seawater, including REEs and PGMs. Marine algae cultivation can generate a significant amount of biomass with minimal freshwater, fertilizer, and land requirements. In summary, the UNCLE-SAM project successfully evaluated the technological feasibility for marine macroalgal cultivation as a feedstock for critical minerals, explored the biological capacity of different seaweeds to provide economically relevant domestic mineral production, assessed processing techniques for thermal co-conversion of seaweeds into renewable fuel and mineral feedstocks, and executed techno-economic and lifecycle assessments for identifying the most critical gaps in our current understanding to move the technology into commercially relevant deployment. Further development of this technology could transform the bioproduct and REE mining industries and catalyze the development of a more sustainable future.

58 GEOSCIENCES↗