Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power boost”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

A High Efficiency DC Bus Regulator/RPC for Spacecraft Applications

DC bus voltage regulation may be required in future high powered spacecraft due to the length of the busses or because they are not generated at precise voltage levels. In these cases the regulation range is often only a few percent increase or decrease, but conventional DC voltage regulators switch all the power passing through them, and this level of power switched determines the size and losses in the regulator. A recently developed concept used a low power DC-DC converter in series with the bs to raise or lower the bus voltage over a small range. This partial power processing technique combines the small size and power losses of the low power converter with the ability to regulate, (over a small range) a high power bus. The Series Connected Buck Boost Regulator (SCBBR) described herein provides bus regulation with an efficiency of 98%. The circuit also provides bus switching and overcurrent limiting functions of a Remote Power Controller (RPC). This paper described the circuit design and performance of a breadboard SCBBR configured as a bus voltage regulator providing plus of minus 40% voltage regulation range, bus switching, and overload limiting.

Birchenough, Arthur G.↗
DOE OSTI2026

Solar-powered self-descaling seesaw extractor for lithium production from seawater

The low Li + concentration and the abundance of competing ions limit the efficiency of lithium extraction from seawater. Here, in this work, we report a solar-powered seesaw extractor (SPSE) to boost Li + adsorption while minimizing scaling caused by competing ions during photothermal evaporation. The SPSE features a sandwich architecture, with a hydrophilic adsorbent layer placed between two hydrophobic photothermal layers. The seesaw configuration enables Li + to be elevated and concentrated through evaporation to overcome sluggish adsorption kinetics, while the associated salt scaling is removed by the seesawing motion. As a demonstration, we assembled 60 SPSEs into a 3 × 20 array that achieved a 15.5-fold increase in local Li + concentration and a 69.1% improvement in Li + uptake over 120 h, with a Li + /Na + separation factor exceeding 370,000.

localized enrichment↗
NASA NTRS1998

A Modular PMAD System for Small Spacecraft

Current trends in satellite design are focused on developing small, reliable, and inexpensive spacecraft. To that end, a modular power management and distribution system (PMAD) is proposed which will help transition the aerospace industry towards an assembly line approach to building spacecraft. The modular system is based on an innovative DC voltage boost converter called the Series Connected Boost Regulator (SCBR). The SCBR uses existing DC-DC converters and adds a unique series connection. This simple modification provides the SCBR topology with many advantages over existing boost converters. Efficiencies of 94-98%, power densities above 1,000 We/kg, and inherent fault tolerance are just a few of the characteristics presented. Limitations of the SCBR technology are presented, and it is shown that the SCBR makes an ideal photovoltaic array regulator. A modular design based on the series connected boost unit is outlined and functional descriptions of the components are given.

Button, Robert M.↗
NASA NTRS1982

Analysis of transistor and snubber turn-off dynamics in high-frequency high-voltage high-power converters

Dc to dc converters which operate reliably and efficiently at switching frequencies high enough to effect substantial reductions in the size and weight of converter energy storage elements are studied. A two winding current or voltage stepup (buck boost) dc-to-dc converter power stage submodule designed to operate in the 2.5-kW range, with an input voltage range of 110 to 180 V dc, and an output voltage of 250 V dc is emphasized. In order to assess the limitations of present day component and circuit technologies, a design goal switching frequency of 10 kHz was maintained. The converter design requirements represent a unique combination of high frequency, high voltage, and high power operation. The turn off dynamics of the primary circuit power switching transistor and its associated turn off snubber circuitry are investigated.

Wilson, P. M.↗
DOE OSTI2025

Evaluating system responses to electric vehicle charging infrastructure expansion through data-driven simulation

Understanding the system responses to electric vehicle (EV) charging infrastructure expansion, including vehicle charging needs, station utilization, and energy consumption, is critical for effective planning to meet growing charging demand without unnecessary resource investment. This study evaluates the system responses to EV charging infrastructure expansion, focusing on charging needs, station utilization, and energy consumption. Using trip data from the National Household Travel Survey and origin–destination patterns, we simulated trip chains in downtown Atlanta with 10 % EV penetration. We assessed 32 scenarios involving different charging port power levels and siting strategies. Furthermore, we found that higher-power ports were more sensitive to placement, with concentrated expansion boosting station utilization more than uniform expansion. Adding high-power ports did not always increase peak energy consumption; in some cases, a few 400 kW ports reduced overall consumption compared to 150 kW ports by enabling faster charging and higher vehicle turnover.

Electric vehicle↗
DOE OSTI2021

Bidirectional interconversion of microwave and light with thin-film lithium niobate

Abstract Superconducting cavity electro-optics presents a promising route to coherently convert microwave and optical photons and distribute quantum entanglement between superconducting circuits over long-distance. Strong Pockels nonlinearity and high-performance optical cavity are the prerequisites for high conversion efficiency. Thin-film lithium niobate (TFLN) offers these desired characteristics. Despite significant recent progresses, only unidirectional conversion with efficiencies on the order of 10 −5 has been realized. In this article, we demonstrate the bidirectional electro-optic conversion in TFLN-superconductor hybrid system, with conversion efficiency improved by more than three orders of magnitude. Our air-clad device architecture boosts the sustainable intracavity pump power at cryogenic temperatures by suppressing the prominent photorefractive effect that limits cryogenic performance of TFLN, and reaches an efficiency of 1.02% (internal efficiency of 15.2%). This work firmly establishes the TFLN-superconductor hybrid EO system as a highly competitive transduction platform for future quantum network applications.

42 ENGINEERING↗
NASA NTRS1984

Design considerations for remotely piloted, high-altitude airplanes powered by microwave energy

Several types of systems have been considered in a design study of unmanned, microwave-powered, long-endurance, high-altitude airplanes. The study includes vehicles that use power from a continuously transmitted beam and other aircraft that receive intermittent power during cycles of boost-glide flight. Simple design algorithms are presented. Examples of sizing and performance analyses are used to suggest design-procedure guidelines.

Morris, C. E. K., Jr.↗
NASA NTRS1991

Self-Oscillating Inductive Boost Regulator

Improved voltage regulator designed for use in solar photovoltaic dc power system utilizing flywheel for energy storage. Includes self-oscillating inductive voltage-boosting circuit, which regulates withdrawal of energy from flywheel and motor/generator when output of solar cells insufficient to maintain load voltage at specified level of 150 Vdc. Features include optical coupling and rapid response.

Paulkovich, John↗
DOE OSTI2022

3.5 kW/in3 Planar Coupled Inductor Design and Optimization for a 50 kW 3-level Four-Switch Buck-Boost (3L-FSBB) Converter

Planar magnetics design has been widely used in power electronics field because of the low profile, ease of manufacturability, and high power density. This paper first proposes a 3-level four-switch buck-boost (3L-FSBB) converter for the dc-dc applications where the zero common-mode (CM) voltage emissions, step-up and step-down are all required. With the consideration of power density, efficiency, and cost, a 15oz heavy copper coupled inductor for 3-level FSBB converter was designed and optimized with the low-cost commercial core and planar windings. According to the soft-switching quadrangle modulation for 3-L FSBB, the turns number and stacked core number are optimized first. And then, a two-board design is proposed to reduce the fringing effect and improve the thermal performance. Finally, a 75 kVA two-stage ac-dc-dc converter including a 3-level FSBB converter was built to verify the electrical design.

Cao, Yuliang↗
DOE OSTI2022

Cooperative fault management for resilient integration of renewable energy

Cooperative fault management (CFM) is designed herein to control different types of renewable energy resources cooperatively during electrical faults. This paper studies systems with a high penetration of photovoltaic (PV) energy and wind energy. First, CFM leverages power converters of PV farms to boost the ride-through capability of nearby doubly-fed induction generators (DFIGs). By controlling PV farms’ output voltages to change smoothly during both fault initiation and fault clearance, the widely used crowbar in DFIGs is less likely to be activated. Crowbar activation adversely makes DFIGs lose controllability and absorb reactive power. The second contribution is the development of a software-defined CFM controller and a controller in-the-loop demonstration of the real-time performance of this optimization-based CFM. CFM capitalizes on distributed optimization formulation to enable flexibility, plug-and-play, and privacy-preserving. Computation time, however, is a major concern for optimization-based dynamics control. Here, real-time controller-in-the-loop simulation results show optimization-based CFM can output reference values around 60 ms and is quick enough for dynamic control.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

Enhancing Synchronous Condenser Operation of Hydrogenerators

Hydropower plants are sometimes dispatched below capacity or even shut down to meet water regulations. These can temporarily be repurposed to operate as synchronous condensers. To enable this capability, this paper proposes a design that allows hydrogenerators to safely operate as synchronous condensers, providing fast voltage and reactive power support under both normal and boost conditions. The proposed design integrates capability curves with hydrogenerators’ excitation systems through modifications using proposed MVA-field current curve, current controller, and limiter. The design is implemented locally at the machine for rapid response. Simulation results demonstrate the effectiveness of the proposed design and using hydrogenerators as synchronous condensers in power grids.

24 - POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1999

Lightweight Battery Charge Regulator Used to Track Solar Array Peak Power

A battery charge regulator based on the series-connected boost regulator (SCBR) technology has been developed for high-voltage spacecraft applications. The SCBR regulates the solar array power during insolation to prevent battery overcharge or undercharge conditions. It can also be used to provide regulated battery output voltage to spacecraft loads if necessary. This technology uses industry-standard dc-dc converters and a unique interconnection to provide size, weight, efficiency, fault tolerance, and modularity benefits over existing systems. The high-voltage SCBR shown in the photograph has demonstrated power densities of over 1000 watts per kilogram (W/kg). Using four 150-W dc-dc converter modules, it can process 2500 W of power at 120 Vdc with a minimum input voltage of 90 Vdc. Efficiency of the SCBR was 94 to 98 percent over the entire operational range. Internally, the unit is made of two separate SCBR s, each with its own analog control circuitry, to demonstrate the modularity of the technology. The analog controllers regulate the output current and incorporate the output voltage limit with active current sharing between the two units. They also include voltage and current telemetry, on/off control, and baseplate temperature sensors. For peak power tracking, the SCBR was connected to a LabView-based data acquisition system for telemetry and control. A digital control algorithm for tracking the peak power point of a solar array was developed using the principle of matching the source impedance with the load impedance for maximum energy transfer. The algorithm was successfully demonstrated in a simulated spacecraft electrical system at the Boeing PhantomWorks High Voltage Test Facility in Seattle, Washington. The system consists of a 42-string, high-voltage solar array simulator, a 77-cell, 80-ampere-hour (A-hr) nickel-hydrogen battery, and a constant power-load module. The SCBR and the LabView control algorithm successfully tracked the solar array peak power point through various load transients, including sunlight discharge transients when the total load exceeded the maximum solar array output power.

Soeder, James F.↗
NASA NTRS2013

Electric Machine with Boosted Inductance to Stabilize Current Control

High-powered motors typically have very low resistance and inductance (R and L) in their windings. This makes the pulse-width modulated (PWM) control of the current very difficult, especially when the bus voltage (V) is high. These R and L values are dictated by the motor size, torque (Kt), and back-emf (Kb) constants. These constants are in turn set by the voltage and the actuation torque-speed requirements. This problem is often addressed by placing inductive chokes within the controller. This approach is undesirable in that space is taken and heat is added to the controller. By keeping the same motor frame, reducing the wire size, and placing a correspondingly larger number of turns in each slot, the resistance, inductance, torque constant, and back-emf constant are all increased. The increased inductance aids the current control but ruins the Kt and Kb selections. If, however, a fraction of the turns is moved from their "correct slot" to an "incorrect slot," the increased R and L values are retained, but the Kt and Kb values are restored to the desired values. This approach assumes that increased resistance is acceptable to a degree. In effect, the heat allocated to the added inductance has been moved from the controller to the motor body, which in some cases is preferred.

Abel, Steve↗
DOE OSTI2021

Design Space Exploration of Emerging Memory Technologies for Machine Learning Applications

Memory design space exploration methods study memory systems’ performances and limitations before implementation. The computer memory design space has grown exponentially because of the enormous growth of memory types, memory controllers, and application software. Computer simulators are commonly used for memory design space exploration. However, complex memory simulations take an enormous amount of time. Hence, in this paper, we proposed a machine learning-based design space exploration method for dynamic random-access memory and non-volatile memory systems. We applied our method to the CosmoGAN and LeNet applications to predict the following six memory response parameters: (i) bandwidth, (ii) power, (iii) average latency, (iv) average total latency, (v) memory reads, and (vi) memory writes. Our experimental results show that machine learning models can predict memory response parameter values faster than simulations. We used support vector machine, random forest, and gradient boosting machine learning models. We observed that the support vector machine provides better performance for bandwidth, average latency, and average total latency. The random forest model works better for memory reads and writes. The gradient boosting model provides superior prediction performance for power. We provide a detailed discussion on learning curve characteristics, error analysis, and memory type recommendation.

Hasan, S M Shamimul↗
DOE OSTI2021

Assessment of sulfur trioxide formation due to enhanced interaction of nitrogen oxides and sulfur oxides in pressurized oxy-combustion

Pressurized oxy-combustion is emerging to be one of the best technologies for significantly decreasing the energy penalty for CO 2 capture in coal-fired power plants. However, the higher pressure boosts the formation of acid gases, including SO 3 and NO 2 , which could increase the risk of corrosion. The synergistic promotion of SO 3 and NO 2 formation in pressurized oxy-combustion is kinetically evaluated under representative conditions (1 ~ 30 atm, 600 ~ 1200 °C, NO/SO 2 = 0.1 ~ 5). We begin with a comprehensive mechanism (72 species and 428 reactions), covering nitrogen and sulfur chemistry, relying on GRI-Mech 3.0. This analysis shows that the interaction of SO X and NO X enhances the conversion rates of SO 2 → SO 3 , and this effect is more apparent at elevated pressures and lower temperatures. Mechanism analyses indicate that at elevated pressures, the formation pathways of SO 3 through HOSO 2 + O 2 = SO 3 + HO 2 , and NO 2 through HO 2 + NO = NO 2 + OH, are promoted due to the strong interaction between SO X and NO X . The intermediate between these two reactions is SO 2 + OH + M = HOSO 2 + M, resulting in a strong cycle, that can be expressed by the global reaction NO + SO 2 + O 2 = NO 2 + SO 3 . Finally, a nine-step reduced chemistry is developed and validated to accurately predict the formation of SO 3 in the post-flame region at elevated pressures.

42 ENGINEERING↗
DOE OSTI2021

Non-degenerate parametric mixing and Q-enhancement in ALN Lamb wave resonator

In this Letter, we explore a non-degenerate phase independent parametric quality factor (Q)-enhancement technique for aluminum nitride (AlN) Lamb wave resonators. Unlike other active Q-enhancement techniques which require precise phase control of the electronic feedback loop, this technique is implemented by parametrically pumping AlN material stiffness to realize a negative resistance seen at the signal path. The negative resistance is dependent on the nonlinear material modulation and multi-resonance coupling in the device. A nonlinear circuit model is developed to simulate the parametric coupling of each resonance and extract the nonlinearity of AlN from experimental data. With proper pump frequency and pump power, the device quality factor is boosted in both simulation and experiment. The demonstrated Q-enhancement method is simple to implement and can be applied to other types of resonators that have nonlinear behavior and support multi-resonance operation.

42 ENGINEERING↗
NASA NTRS1976

Investigation of TC-1 flight failure using power spectral analysis

During the Titan Centaur 1 test flight a failure involving at least one of the Centaur propellant boost pumps occurred. Also, neither of the boost pump speed instruments indicated pump rotation. Accelerometer data from the Titan Centaur 1 flight failure were analyzed using power spectral density methods to determine boost pump speed during attempted starts of the Centaur. The technique was demonstrated on a reference flight. The hydrogen boost pump speed transient was determined for the TC-1 flight. Other trends are seen in the data. However, these are not believed to be the oxygen boost pump. Discussion of data enhancement techniques is also presented.

Lorenzo, C. F.↗