Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “powders”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Initial results from boron powder injection experiments in WEST lower single null L-mode plasmas

Using a recently installed impurity powder dropper (IPD), boron powder (<150 μm) was injected into lower single null (LSN) L-mode discharges in WEST. IPDs possibly enable real-time wall conditioning of the plasma-facing components and may help to facilitate H-mode access in the full-tungsten environment of WEST. The discharges in this experiment featured I p = 0.5 MA, B T = 3.7 T, q 95 = 4.3, t pulse = 12–30 s, n e,0 ~ 4 × 10 19 m –2 , and P LHCD ~ 4.5 MW. Estimates of the deuterium and impurity particle fluxes, derived from a combination of visible spectroscopy measurements and their corresponding S/XB coefficients, showed decreases of ~50% in O + , N + , and C + populations during powder injection and a moderate reduction of these low-Z impurities (~50%) and W (~10%) in the discharges that followed powder injection. Along with the improved wall conditions, WEST discharges with B powder injection observed improved confinement, as the stored energy W MHD , neutron rate, and electron temperature T e increased significantly (10%–25% for W MHD and 60%–200% for the neutron rate) at constant input power. Notably, these increases in confinement scale up with the powder drop rate and are likely due to the suppression of ion temperature gradient (ITG) turbulence from changes in Z eff and/or modifications to the electron density profile.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Mitigation of plasma–wall interactions with low-Z powders in DIII-D high confinement plasmas

Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in H-mode plasmas (I p = 1 MA, B t = 2 T, P NB = 6 MW, < n e > = 3.6–5.0 · 10 19 m –3 ) into the upper small-angle slot divertor for 2 s intervals at constant rates of 3–204 mg s –1 . The multi-species BN powders at a rate of 54 mg s –1 showed the most substantial increase in divertor neutral compression by more than an order of magnitude and lasting detachment with minor degradation of the stored magnetic energy W mhd by 5%. Rates of 204 mg s –1 of boron nitride powder further reduce edge localized mode-fluxes on the divertor but also cause a drop in confinement performance by 24% due to the onset of an n = 2 tearing mode. The application of powders also showed a substantial improvement of wall conditions manifesting in reduced wall fueling source and intrinsic carbon and oxygen content in response to the cumulative injection of non-recycling materials. Furthermore, the results suggest that low-Z powder injection, including mixed element compounds, is a promising new core-edge compatible technique that simultaneously enables divertor detachment and improves wall conditions during high confinement operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Initial Results from Boron Powder Injection Experiments in WEST Lower Single Null L-mode Plasmas

Using a recently installed impurity powder dropper (IPD), boron powder (< 150 μm) was injected into lower single null (LSN) L-mode discharges in WEST. IPDs possibly enable real-time wall conditioning of the plasma-facing components and may help to facilitate H-mode access in the full-tungsten environment of WEST. The discharges in this experiment featured Ip = 0.5 MA, BT = 3.7 T, q95 = 4.3, tpulse = 12–30 s, ne,0 ~ 4×1019 m-2, and PLHCD ~ 4.5 MW. Estimates of the deuterium and impurity particle fluxes, derived from a combination of visible spectroscopy measurements and their corresponding S/XB coefficients, showed decreases of ~ 50% in O+, N+, and C+ populations during powder injection and a moderate reduction of these low-Z impurities (~ 50%) and W (~ 10%) in the discharges that followed powder injection. Along with the improved wall conditions, WEST discharges with B powder injection observed improved confinement, as the stored energy WMHD, neutron rate, and electron temperature Te increased significantly (10–25% for WMHD and 60–200% for the neutron rate) at constant input power. These increases in confinement scale up with the powder drop rate and are likely due to the suppression of ion temperature gradient (ITG) turbulence from changes in Zeff and/or modifications to the electron density profile.

Boronization↗
DOE OSTI2022

An Easy‐to‐Use Custom‐Built Cell for Neutron Powder Diffraction Studies of Rechargeable Batteries

Abstract In operando powder diffraction remains one of the most powerful tools for non‐destructive investigation of battery electrode materials. While in operando X‐ray, especially synchrotron radiation, powder diffraction is by now a routine experimental technique, in operando neutron powder diffraction is still less established. We present a new electrochemical cell for in operando neutron powder diffraction, which is, first and foremost, easy to use, but can also cycle electrode materials under electrochemical conditions close to those achieved using standard laboratory cells. The cell has been designed in multiple sizes, and high‐quality electrochemical and neutron powder diffraction data is presented for sample sizes as low as 48 mg total active material. The cell handles lithium‐ion and sodium‐ion materials equally well, with no difference in how the cell is prepared and assembled. The cell is intended to be used as sample environment at powder diffractometers at the neutron facilities MLZ, ORNL and ACNS.

25 ENERGY STORAGE↗
DOE OSTI2023

First of Their Kind: Solar Cells with a Dry-Processed Perovskite Absorber Layer via Powder Aerosol Deposition and Hot-Pressing

Preparing halide perovskite films by solvent-free, powder-based processing approaches currently attracts more and more attention. However, working solar cells employing dry, powder-based halide perovskite thin films, have not been demonstrated so far. Herein, perovskite solar cells are presented where the absorber layer is prepared by transferring readily synthesized perovskite powders into a compact thin film using a fully dry-powder-processing concept. Compact thin films are deposited via an optimized powder aerosol deposition (PAD) process. Pressing at 120 °C further improves the morphology and the optoelectronic film properties. Integrating the perovskite films in a solar cell configuration results in fully working devices, with champion power conversion efficiencies of >6%. While the (optoelectronic) properties of the PAD-processed films are found to be comparable with their solution-processed counterparts, investigations of the solar cell stack suggest deterioration of the electron-transport layer properties due to the PAD process, and the presence of hydrates at the perovskite surface to be important factors that contribute to the limited solar cell efficiency. Herein, perspectives to overcome the identified limitations are outlined, emphasizing the high potential and realizability of efficient perovskite solar cells based on dry-powder-processing approaches in the future.

14 SOLAR ENERGY↗
DOE OSTI2024

Integrated modeling of boron powder injection for real-time plasma-facing component conditioning

An integrated modeling framework for investigating the application of solid boron (B) powder injection for real-time surface conditioning of plasma-facing components (PFCs) in tokamak environments is presented. Utilizing the DIII-D impurity powder dropper (IPD) setup, this study simulates B powder injection scenarios ranging from milligrams to tens of milligrams per second, corresponding to boron flux rates of 10 20 –10 21 B/s in standard L-mode conditions. The comprehensive modeling approach combines EMC3-EIRENE for simulating the deuterium plasma background and the Dust Injection Simulator (DIS) for the ablation and transport of the boron powder particles. EMC3 trace impurity fluid modeling results show substantial boron transport to the inboard lower divertor, predominantly influenced by the main ion plasma flow. The dependency on powder particle size (5-250 µm) was found to be insignificant for the scenario considered. The effects of erosion and redeposition were considered to reconcile the discrepancies with experimental observations, which saw substantial deposition on the outer divertor plasma-facing components. For this purpose, the WallDYN3D code was updated to include boron sources within the plasma domain and integrated into the modeling framework. The mixed-material migration modeling shows evolving boron deposition patterns, suggesting the formation of mixed B-C layers or predominantly B coverage depending on the powder mass flow rate. While the modeling outcomes at lower B injection rates tend to align with DIII-D experimental observations, the prediction of near-pure boron layers at higher rates has yet to be experimentally verified in the carbon environment of the DIII-D tokamak. The extensive reach of boron layers found in the modeling suggests the need for modeling that encompasses the entire wall geometry for more accurate experimental correlations. This integrated approach sets a precedent for analyzing and applying real-time in-situ boron coating techniques in advanced tokamak scenarios, potentially extendable to ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

A Prediction Method for Catchment Efficiency Loss due to Coaxial Nozzle Wear in Powder Fed Directed Energy Deposition Systems

Abstract Powder fed laser directed energy deposition systems show significant promise and their widespread adoption could greatly advance manufacturing technology; however, a significant amount of gas atomized metal powder is wasted during material deposition. As contaminated powder must be collected and disposed of as hazardous waste, this process is often criticized for its low catchment efficiency. This presents potential implementation and scaling issues, as widespread use of this technology would directly increase the amount of contaminated powder in need of safe disposal. A direct contribution to this waste issue was identified in past work as wearing exterior and interior surfaces on a replaceable nozzle component within the additive head of such a system integrated into a hybrid manufacturing machine tool. A computational fluid dynamics simulation is developed specifically for use within the manufacturing process by predicting catchment efficiency losses before a deposition operation is performed. The model is robust enough to calculate a catchment efficiency estimate within a reasonable transition time before deposition and is designed to replace visual estimation of nozzle deterioration by the machine operator. Both of two previously identified wear modes are represented in the simulation. Their effects on powder stream geometry are discussed in detail and the results are compared with in-situ measurements of powder stream geometry and concentrations. The resulting work contributes to the growing understanding of using prediction and prevention methods on catchment efficiency related part defects within these systems.

DeWitte, Lisa↗
NASA NTRS1983

Surface characterization of Ti and Ti (6 percent, Al-4 percent, V) metal powders and interaction with primer solutions

The interaction of Ti and Ti 6-4 powders with water and primer solutions was investigated experimentally by measuring the heats of immersion. Similar comparative studies were made on anatase and rutile TiO2 powders. The surface oxide layers of Ti and Ti 6-4 cracked on heating in vacuum between 300 and 400 C as evidenced by high heats of immersion in both water and primer solutions. Polyimide and polyphenylquinoxaline interacted preferentially, compared with the solvents with both metal powders after outgassing at room temperature. The heats of immersion of Ti 6-4 in water, solvents, and primer solutions increased significantly after pretreatment of the powder by an alkaline etch and a phosphate-fluoride process. The TiO2 powders were not satisfactory models for the surface oxide layer on either Ti or Ti 6-4 powder.

Siriwardane, R. V.↗
NASA NTRS1989

Nitriding kinetics of Si-SiC powder mixtures as simulations of reaction bonded Si3N4-SiC composites

The nitriding kinetics of Si and Si plus SiC powder mixtures were studied to simulate the fabrication of RBSN-SiC ceramic matrix composites. Very clean, assynthesized, and solvent-exposed powders were studied; C-rich and Si-rich SiC 0.04-0.05 micron diameter powders were mixed in varying concentrations with SiH4-derived 0.2-0.3 micron diameter Si powder. Complete nitridation is achieved with C-rich SiC powders in 140 min at 1250 C, and in the centers of Si-rich SiC powders in 15 min. The effects on the incubation periods, fast reaction periods, and slow reaction periods that characterize these nitriding processes were studied to explain unusual reverse reaction gradients and other effects of contamination.

Lightfoot, A.↗
NASA NTRS1990

The development of an alternative thermoplastic powder prepregging technique

Discussed is a novel powder prepregging technique that is based on the deposition of the powder onto fibers that have been moistened using an ultrasonic humidifier. The moisture acts as an initial binding agent for the powder until the powder can be melted onto the fiber in a subsequent heating step. LaRC-TPI powder, produced by Mitsui Toastsu, and Hercules AS-4 fiber served as the process development material system. The influence of powder particle size on this process, and the quality of the resulting composite are discussed.

Ogden, A. L.↗
NASA NTRS1995

Powder-Coated Towpreg: Avenues to Near Net Shape Fabrication of High Performance Composites

Near net shape parts were fabricated from powder-coated preforms. Key issues including powder loss during weaving and tow/tow friction during braiding were addressed, respectively, by fusing the powder to the fiber prior to weaving and applying a water-based gel to the towpreg prior to braiding. A 4:1 debulking of a complex 3-D woven powder-coated preform was achieved in a single step utilizing expansion rubber molding. Also, a process was developed for using powder-coated towpreg to fabricate consolidated ribbon having good dimensional integrity and low voids. Such ribbon will be required for in situ fabrication of structural components via heated head advanced tow placement. To implement process control and ensure high quality ribbon, the ribbonizer heat transfer and pulling force were modeled from fundamental principles. Most of the new ribbons were fabricated from dry polyarylene ether and polymide powders.

Johnston, N. J.↗
NASA NTRS2005

Pods: a Powder Delivery System for Mars In-situ Organic, Mineralogic and Isotopic Analysis Instruments

Many Mars in situ instruments require fine-grained high-fidelity samples of rocks or soil. Included are instruments for the determination of mineralogy as well as organic and isotopic chemistry. Powder can be obtained as a primary objective of a sample collection system (e.g., by collecting powder as a surface is abraded by a rotary abrasion tool (RAT)), or as a secondary objective (e.g, by collecting drill powder as a core is drilled). In the latter case, a properly designed system could be used to monitor drilling in real time as well as to deliver powder to analytical instruments which would perform complementary analyses to those later performed on the intact core. In addition, once a core or other sample is collected, a system that could transfer intelligently collected subsamples of power from the intact core to a suite of analytical instruments would be highly desirable. We have conceptualized, developed and tested a breadboard Powder Delivery System (PoDS) intended to satisfy the collection, processing and distribution requirements of powder samples for Mars in-situ mineralogic, organic and isotopic measurement instruments.

Saha, C. P.↗
NASA NTRSDate not supplied

Quick and Correlative TOF-SIMS Analysis of Dispersoid Content in Powder Feedstock and Printed Oxide Dispersion Strengthened Alloys

Oxide dispersion strengthening (ODS) of metal alloys, when combined with additive manufacturing (AM), can be used to solve high-temperature material application problems. The performance of ODS materials is dependent on nano-scale oxide being distributed uniformly throughout the metal matrix; a homogenous distribution is critical to the creep and yield strength. Therefore, quantifying and analyzing these oxide nanoparticles is essential for ODS alloy development. Assessing the chemistry and morphology of dispersoids in a material can be conducted using a variety of X-ray and electron-based methods. Time of Flight Secondary Ion Mass Spectrometry (TOF-SIMS), which assesses chemical concentrations from ion masses, provides the necessary spatial resolution and avoids potential spectral overlap of all elements present. In this work, preparing ODS powder feedstock and Laser Powder Bed Fusion AM was conducted with a NiCoCr alloy and yttria dispersoid, mixed with a Resodyn resonance mixer and printed on an EOS M100 3D printer at NASA Glenn. TOF-SIMS was performed on a Physical Electronics NanoTOF TRIFT V TOF-SIMS at Case Western Reserve University. The TOF-SIMS results collected on the feedstock powder samples correspond to the qualitative interpretation of the homogeneity of the oxide coating on the metal powder from SEM images. This provides quantitative support to the qualitative microscopy images collected earlier in the process design phase. The variance in the yttrium distribution on the powder feedstock samples also correlated with the variance of the yttrium distribution detected in the printed samples. This correlation supported the hypothesis that an even coating of yttria on the metal powders contributes to an even distribution of yttria in the printed material.

Laura G. Wilson↗
DOE OSTI2022

Method for nano powder loading into micro-capillary mold

A method loading powder into a mold can include immersing the mold comprising one or more microchannels into a suspension comprising the powder and a surfactant suspended in a dispersant, wherein the powder comprises particles having an average particle size of less than 100 μm, wherein the mold is substantially entirely covered by the suspension; heating the suspension having the mold immersed therein under a temperature condition suitable to lower the stability of the particles of the powder in the suspension such that the particles settle out of solution and into the one or more microchannels; and applying an ultrasonic wave to the heated suspension to further settle the particles of the powder into the one or more microchannels thereby filling the one or more microchannels of the mold with the powder.

Yacout, Abdellatif M.↗
DOE OSTI2023

Tailored particles for powder-based additive manufacturing

The present disclosure relates to a plurality of powder particles configured to be joined in an additive manufacturing process to form a part. Each one of the powder particles has a determined three dimensional, non-spherical shape. The plurality of powder particles are further of dimensions enabling fitting individual ones of the powder particles in abutting relationship with one another. At least a subplurality of the powder particles each have a functionalized surface feature to enhance at least one of clustering or separation of the subplurality of powder particles.

Watts, Seth Evan↗
DOE OSTI2021

Comparison of active impurity control between lithium and boron powder real-time injection in EAST

The lithium and boron powder have been successfully real-time injected into Experimental Advanced Superconducting Tokamak (EAST) high-confinement (H-) mode discharges, showing good wall conditioning effects, especially on the impurities control. Both of lithium and boron powder particles are gravitationally accelerated into the upper edge of a upper single null discharge. The lithium powder real-time injection effectively reduced the tungsten impurity content both in the plasma edge and core. Contrary to the lithium injection, the boron injection mainly reduced the impurities content in the plasma core, while the impurities increased in the edge. Furthermore, this mainly due to that there was an edge harmonic mode stimulated by boron injection, providing sufficient particles transport. Moreover, the impurities control through boron injection has much wider operation windows than lithium powder injection. Furthermore, there was accumulative wall conditioning effects after sequential boron powder injection discharges.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Revealing mechanisms of processing defect mitigation in laser powder bed fusion via shaped beams using high-speed X-ray imaging

The laser powder bed fusion (LPBF) process utilizing a focused Gaussian-shaped beam faces challenges, including pore formation, melt pool fluctuation and liquid spattering. While beam shaping technology has been explored as a potential approach for defect mitigation, the beam-matter interaction dynamics during melting with shaped beams remain unclear. Here, we report the direct observation of ring-shaped beam-matter interaction dynamics, including pore formation, melt pool fluctuation and liquid spattering, and unveil defect mitigation mechanisms in ring-shaped beam laser powder bed fusion process. Here, we find that, by spatially manipulating incident laser rays, the ring-shaped beam controls keyhole morphology, thereby managing the distribution of the reflected rays. This manipulation can effectively eliminate the formation of an unstable cavity at the keyhole tip, stabilizing the keyhole and mitigating keyhole pores. This enhanced keyhole stability effectively reduces the melt pool fluctuation, the formation of liquid breakup induced spatters and liquid droplet colliding induced large spatters in the laser powder bed fusion process. Additionally, the high-energy forefront of the ring-shaped beam effectively melts the powder bed, reducing agglomeration liquid spatter in the laser powder bed fusion process. The discovered defect mitigation mechanisms may guide the design of beam shaping strategies for simultaneously increasing the quality and productivity of metal additive manufacturing.

Beam shaping↗
DOE OSTI2022

Manufacture aluminum alloy tube from powder with a single-step extrusion via ShAPE

Mechanical performance of aluminum in terms of strength, wear and corrosion resistance, especially high-temperature strength has been shown to improve with the addition of transition metal (TM) elements of Fe, Cr, and Ti. However, these feedstock materials occur as powders. As such, the traditional fabrication process is complex and expensive because it requires multiple procedures and consumes considerable energy. This study developed Shear Assisted Processing and Extrusion (ShAPE) as a single-step process that manufactures tubes directly from Al-TM powders obtained via gas atomization. Meter-long Al-TM alloy tubes are extruded from powders with different processing conditions. The ShAPE tubes have very low porosity and the average density is 2.94 kg/cm 3 , which is equal to or higher than parts fabricated by hot extrusion and sintering. The powder-to-tube fabrication process was revealed and discussed by examining the microstructural evolution. The Vickers hardness of ShAPE tubes ranges from 110 to 140 HV through wall thickness and at different extrusion speeds. The variation in hardness was correlated with the extent of refinement of intermetallics and attributed to the shear deformation per unit extrusion length. Energy cost analysis shows that ShAPE save ~60% energy compared to the conventional sintering and extrusion processes. Results indicate ShAPE is a low-cost, high-efficiency manufacturing process for producing tubes from metallic powders.

36 MATERIALS SCIENCE↗