Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polycrystalline”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Kinetics of the luminescence decay of Fe{sup 2+} impurity centres in polycrystalline ZnSe upon excitation by an electron beam

The kinetics of the decay of the luminescence of Fe{sup 2+} ions is measured at nitrogen temperature in polycrystalline ZnSe excited by a short pulse of accelerated electrons. The time dependence of the luminescence intensity differs from the exponential one, observed upon excitation of luminescence by a short light pulse. The obtained nonexponential dependence is theoretically described. The explanation is based on the quenching effect of the excited state of the Fe{sup 2+} ion by free electrons of the volume charge of the current of accelerated electrons in the sample (Auger effect). It was shown that the relaxation of the volume charge after the electron-accelerating voltage is removed makes a significant contribution to the decay kinetics of the impurity luminescence. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

High pressure phase transition and strength estimate in polycrystalline alumina during laser-driven shock compression

Alumina (Al 2 O 3 ) is an important ceramic material notable for its compressive strength and hardness. It represents one of the major oxide components of the Earth's mantle. Static compression experiments have reported evidence for phase transformations from the trigonal α-corundum phase to the orthorhombic Rh 2 O 3 (II)-type structure at ~90 GPa, and then to the post-perovskite structure at ~130 GPa, but these phases have yet to be directly observed under shock compression. In this work, we describe laser-driven shock compression experiments on polycrystalline alumina conducted at the Matter in Extreme Conditions endstation of the Linac Coherent Light Source. Ultrafast x-ray pulses (50 fs, 10 12 photons/pulse) were used to probe the atomic-level response at different times during shock propagation and subsequent pressure release. At 107 ± 8 GPa on the Hugoniot, we observe diffraction peaks that match the orthorhombic Rh 2 O 3 (II) phase with a density of 5.16 ± 0.03 g cm –3 . Upon unloading, the material transforms back to the α-corundum structure. Upon release to ambient pressure, densities are lower than predicted assuming isentropic release, indicating additional lattice expansion due to plastic work heating. Furthermore, using temperature values calculated from density measurements, we provide an estimate of alumina's strength on release from shock compression.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Dislocation dynamics in polycrystalline materials

An extension of the dislocation dynamics method to polycrystalline materials is presented with emphasis on handling interactions between dislocations and grain boundaries. The key new features of the method include: (1) a grain boundary detection algorithm, (2) new dislocation emission criteria based on power dissipation and area growth, (3) mobility of dislocations at grain boundaries, and (4) extension of topological operations e.g. mesh adaption, collision, and dissociation to handle dislocations interacting with grain boundaries. Furthermore, verification and validation examples are executed to compare our calculations with existing analytic methods, molecular dynamics simulations, and experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A density-wave-like transition in the polycrystalline V 3 Sb 2 sample with bilayer kagome lattice

Recently, transition-metal-based kagome metals have aroused much research interest as a novel platform to explore exotic topological quantum phenomena. Here we report on the synthesis, structure, and physical properties of a bilayer kagome lattice compound V 3 Sb 2 . The polycrystalline V 3 Sb 2 samples were synthesized by conventional solid-state-reaction method in a sealed quartz tube at temperatures below 850 °C. Measurements of magnetic susceptibility and resistivity revealed consistently a density-wave-like transition at T dw ≈ 160 K with a large thermal hysteresis, even though some sample-dependent behaviors were observed presumably due to the different preparation conditions. Upon cooling through T dw , no strong anomaly in lattice parameters and no indication of symmetry lowering were detected in powder x-ray diffraction measurements. This transition can be suppressed completely by applying hydrostatic pressures of about 1.8 GPa, around which no sign of superconductivity was observed down to 1.5 K. Specific-heat measurements revealed a relatively large Sommerfeld coefficient γ = 18.5 mJ∙mol –1 ∙K –2 , confirming the metallic ground state with moderate electronic correlations. Density functional theory calculations indicate that V 3 Sb 2 shows a non-trivial topological crystalline property. Furthermore, our study makes V 3 Sb 2 a new candidate of metallic kagome compound to study the interplay between density-wave-order, nontrivial band topology, and possible superconductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Magnetic Damping in Polycrystalline Thin-Film Fe-V Alloys

Here, we report on the magnetic damping properties of polycrystalline Fe-V alloy thin films that are deposited at room temperature. By varying the concentration of V in the alloy, the saturation magnetization can be adjusted from that of Fe to near zero.We show that exceptionally low values of the damping parameter can be maintained over the majority of this range, with a minimum damping at approximately 15%–20% V concentration. Such a minimum is qualitatively reproduced with ab initio calculations of the damping parameter, although at a concentration closer to 10% V. The measured intrinsic damping has a minimum value of (1.53±0.08)×10 –3 , which is approximately a factor of 3 higher than our calculated value of 0.48×10 –3 . From first-principles theory, we outline the factors that are mainly responsible for the trend of the damping parameter in these alloys. In particular, the band structure and resulting damping mechanism is shown to change at V concentrations greater than approximately 35% V content.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Temperature-dependent lattice dynamics in polycrystalline ZrN

Zirconium nitride holds promise for improving nuclear reactor components, where thermal conductivity is important, highlighting the need for a detailed understanding of its phonons. However, the phonon dispersion derived from previous inelastic neutron scattering data is in disagreement with modern theoretical calculations, pointing to the necessity for further experimental validation. Here, in this study, we use inelastic neutron scattering experiments on polycrystalline ZrN at 6, 100, 300, 400, and 600 K, and density functional theory (DFT) calculations to study the momentum-resolved scattering and the phonon density of states. Both experimental and theoretical results reveal a phonon cutoff energy near 65 meV, in stark disagreement with previous single-crystal neutron scattering measurements indicating a cutoff near 75 meV. The 65 meV cutoff energy is, however, in reasonable agreement with previous measurements on ZrN 0.9 . Consistency between our theoretical and experimental results confirms that ZrN is a wide phonon band gap system and that DFT provides a reliable description of its phonons.

DFT↗
DOE OSTI2021

Imaging CdCl 2 defect passivation and formation in polycrystalline CdTe films by cathodoluminescence

Polycrystalline thin-film solar cells are attractive for low-cost photovoltaics, but their efficiencies are hindered by material quality issues. State-of-the-art CdTe solar cells use CdCl 2 annealing treatments whose effects are still being discovered at a fundamental level. Here, a series of CdTe samples with different annealing temperatures is investigated with high-resolution hyperspectral cathodoluminescence mapping measured at both room temperature and low temperature on the same microscopic areas. A statistical analysis over a large number of grains is combined with a local analysis at grain boundaries. The results elucidate the dynamic interplay between grain boundary and intragrain defect passivation and formation, in the midst of grain growth. The CdCl 2 annealing initially contributes to an increase of the grain size and the passivation of both grain boundaries and grain interiors, increasing the overall luminescence and diffusion length. For higher annealing temperatures, a further increase of grain size is counterbalanced by the rise of bulk defects. The results illustrate the tradeoffs that lead to an optimal annealing temperature, as well as new methods for understanding defect passivation and creation in thin film solar cells.

14 SOLAR ENERGY↗
DOE OSTI2024

In situ coherent x-ray scattering reveals polycrystalline structure and discrete annealing events in strongly coupled nanocrystal superlattices

Solution-phase bottom up self-assembly of nanocrystals into superstructures such as ordered superlattices is an attractive strategy to generate functional materials of increasing complexity, including very recent advances that incorporate strong interparticle electronic coupling. While the self-assembly kinetics in these systems have been elucidated and related to the product characteristics, the weak interparticle bonding interactions suggest the superstructures formed could continue to order within the solution long after the primary nucleation and growth have occurred, even though the mechanism of annealing remains to be elucidated. Here, we use a combination of Bragg coherent diffractive imaging and x-ray photon correlation spectroscopy to create real-space maps of supercrystalline order along with a real-time view of the strain fluctuations in aging strongly coupled nanocrystal superlattices while they remain suspended and immobilized in solution. By combining the results, we deduce that the self-assembled superstructures are polycrystalline, initially comprising multiple nucleation sites, and that shear avalanches at grain boundaries continue to increase crystallinity long after growth has substantially slowed. This multimodal approach should be generalizable to characterize a breadth of materials in their native chemical environments, thus extending the reach of high-resolution coherent x-ray characterization to the benefit of a much wider range of physical systems. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evolution of texture and internal stresses within polycrystalline rock salt using in situ 3D synchrotron computed tomography and 3D X-ray diffraction

Over time rock salt caverns have been extensively used as reliable repositories for hazardous waste such as nuclear waste, oil or compressed gases. Undisturbed rock salt deposits in nature are usually impermeable and have very low porosity. However, rock salt formations under excavation stresses can develop crack networks, which increase their porosities; and in the case of a connected crack network within the media, rock salt may become permeable. Although the relationship between the permeability of rock salt and the applied stresses has been reported in the literature, a microscopic study that investigates the properties influencing this relationship, such as the evolution of texture and internal stresses, has yet to be conducted. This study employs in situ 3D synchrotron micro-computed tomography and 3D X-ray diffraction (3DXRD) on two small-scale polycrystalline rock salt specimens to investigate the evolution of the texture and internal stresses within the specimens. The 3DXRD technique measures the 3D crystal structure and lattice strains within rock salt grains. The specimens were prepared under 1D compression conditions and have shown an initial {111} preferred texture, a dominant {110}$\langle1\bar{1}0\rangle$ slip system and no fully connected crack network. The {111} preferred texture under the unconfined compression experiment became stronger, while the {111}$\langle1\bar{1}0\rangle$ slip system became more prominent. The specimens did not have a fully connected crack network until applied axial stresses reached about 30 MPa, at a point where the impermeability of the material becomes compromised due to the development of multiple major cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The T 2 structure of polycrystalline cubic human insulin

The polymorphism of human insulin upon pH variation was characterized via X-ray powder diffraction, employing a crystallization protocol previously established for co-crystallization with phenolic derivatives. Two distinct rhombohedral ( R 3) polymorphs and one cubic ( I 2 1 3) polymorph were identified with increasing pH, corresponding to the T 6 , T 3 R 3 f and T 2 conformations of insulin, respectively. The structure of the cubic T 2 polymorph was determined via multi-profile stereochemically restrained Rietveld refinement at 2.7 Å resolution. This constitutes the first cubic insulin structure to be determined from crystals grown in the presence of zinc ions, although no zinc binding was observed. The differences of the polycrystalline variant from other cubic insulin structures, as well as the nature of the pH-driven phase transitions, are discussed in detail.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Voltage Loss Comparison in CdSe/CdTe Solar Cells and Polycrystalline CdSeTe Heterostructures

Cd(Se)Te solar cells have considerable headroom to increase voltage. Voltage losses occur due to incomplete absorption above bandgap E_g and band tail absorption below E_g; such losses are quantified using radiative voltage. The largest voltage losses are attributed to nonradiative recombination, which is quantified via carrier lifetime and radiative efficiency. We compare radiative voltage, radiative efficiency, and carrier lifetime for Cu-doped CdSe/CdTe solar cells and for undoped polycrystalline CdSeTe heterostructures passivated with Al_2O_3. Using external quantum efficiency spectrum and a CdSeTe absorption spectrum obtained from absolute photoluminescence (PL), we show that the radiative voltage is greater than 1.1 V. Time-resolved PL experiments and modeling show that a major part of voltage losses can be attributed to recombination in the absorber bulk. The front interface recombination makes a larger impact within the first few nanoseconds after pulsed excitation, and the comparison of time-gated and time-integrated PL can be used to assess relative contributions of front interface and bulk recombination rates.

14 SOLAR ENERGY↗
DOE OSTI2025

High-Throughput In-Line Deposition of Silicon Oxide for Polycrystalline Silicon Passivating Contacts

Polycrystalline silicon passivating contacts rely on an ultrathin (1–2 nm) silicon oxide layer to minimize recombination at the wafer/oxide interface and regulate dopant diffusion. Traditionally formed by thermal or chemical oxidation, this oxide is herein replaced by silicon oxide deposited via aerosol impact-driven assembly (AIDA), enabling high wafer-per-hour throughput and precise thickness control. In this study, we show that AIDA coatings conformally cover planar or textured substrates and achieve a SiO x /poly-Si(n) structure with an implied open-circuit voltage (iV oc = 726 mV) and contact saturation current density (J 0 = 8.8 fA/cm 2 ). Furthermore, annealing AIDA SiO x films at elevated temperatures desorbs hydroxyl groups while the stoichiometry transitions toward SiO 2 , improving passivation quality. Together, these results highlight AIDA’s potential for scalable, high-throughput manufacturing of advanced passivating contacts, offering a cost-effective alternative to conventional low-pressure chemical vapor deposition and plasma-enhanced chemical vapor deposition-based silicon and oxide processes.

TOPcon↗
DOE OSTI2020

Enhancing Photocarrier Bulk Lifetime with Defect Engineering of Polycrystalline Passivated-Contact n-Cz Photovoltaic Devices

We study the photocarrier lifetime evolution of n-Cz Si material throughout the processing sequence for polycrystalline passivated contact devices. We show that a high temperature annealing pretreatment (known as Tabula Rasa) has a clear effect on enhancing bulk lifetimes of n-Cz Si. We further this development by integrating such defect engineering into the lower-temperature annealing of passivated contact. By applying oxidizing ambient gases during these anneals we report a photocarrier lifetime enhancement over an N 2 environment. This enhancement is exhibited in a 1-sun iV OC of 735 mV when annealed in O 2 rather than 708 mV in N 2.

14 SOLAR ENERGY↗
DOE OSTI2020

Arsenic Doping of Polycrystalline CdSeTe Devices for Microsecond Life-times with High Carrier Concentrations

We report seminal advances in fabrication and understanding of group V (As) doped thin-film polycrystalline CdTe-based solar cells. The devices are fabricated using a novel approach, by sublimating layers of CdSeTe and CdSeTe:As. This new method allowed us to achieve minority carrier lifetime of over 1 μs, carrier concentration of more than 5×l0 15 cc -1 and external radiative efficiency of over 2 % in a device configuration. We find an increase in open-circuit voltage when comparing As-doped, Cu-doped and undoped devices. The choice of CdSeTe instead of a CdTe-only absorber has been explained using first-principle density functional theory model. A SCAPS device model is used to analyze the potential causes for lower open-circuit voltage.

Munshi, Amit H.↗
DOE OSTI2022

High grain boundary recombination velocity in polycrystalline metal halide perovskites

Understanding carrier recombination processes in metal halide perovskites is fundamentally important to further improving the efficiency of perovskite solar cells, yet the accurate recombination velocity at grain boundaries (GBs) has not been determined. Here, we report the determination of carrier recombination velocities at GBs (S GB ) of polycrystalline perovskites by mapping the transient photoluminescence pattern change induced by the nonradiative recombination of carriers at GBs. Charge recombination at GBs is revealed to be even stronger than at surfaces of unpassivated films, with average S GB reaching 2200 to 3300 cm/s. Regular surface treatments do not passivate GBs because of the absence of contact at GBs. We find a surface treatment using tributyl(methyl)phosphonium dimethyl phosphate that can penetrate into GBs by partially dissolving GBs and converting it into one-dimensional perovskites. It reduces the average S GB by four times, with the lowest SGB of 410 cm/s, which is comparable to surface recombination velocities after passivation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Diffuse-Interface Model for Predicting the Evolution of Metallic Negative Electrodes and Interfacial Voids in Solid-State Batteries with Homogeneous and Polycrystalline Solid Electrolyte Separators

Here, this paper presents a novel diffuse-interface electrochemical model that simultaneously simulates the evolution of the metallic negative electrode and interfacial voids during the stripping and plating processes in solid-state batteries. The utility and validity of this model are demonstrated for the first time on a cell with a sodium (Na) negative electrode and a Na-β″-alumina ceramic solid electrolyte (SE) separator. Three examples are simulated. First, stripping and plating with a perfect electrode/electrolyte interface; second, stripping and plating with a single interfacial void at the electrode/electrolyte interface; third, stripping with multiple interfacial voids. Both homogeneous and polycrystalline SEs with low and high-conductivity grain boundaries (GBs) are considered for all three examples. Heterogeneous GB conductivity marginally impacts the thickness of the Na electrode in cases with a perfect electrode/electrolyte interface. Moreover, it results in local changes to void growth due to the interactions between the void edge and the GBs. The void growth rate is a linear function of the flux of Na atoms at the void edge, which in turn depends on the applied current density. We also show that the void coalescence rate increases with applied current density and can be marginally influenced by GB conductivity.

batteries↗
DOE OSTI2024

Self-Organized Stress Distributions in Polycrystalline Materials [Dissertation]

Understanding stress distributions in solid materials is complicated by the fact that most materials are polycrystalline in nature, with each crystal having an elastically anisotropic reaction to force. This study is to gain a better understanding on how external forces placed on a polycrystal are related to internal reactions within and between the grains. The hypothesis is that the stress distribution in porous to fully dense materials are self-organized based on strong contacts between and within the individual grains created by force chains. Force chains, commonly known in loaded granular materials, and could be the phenomenon that connect micro to macro deformation. Scale bridging measurements conducted through Raman spectroscopy, Atomic Force Microscopy, and Digital Image Correlation will be used to create stress maps, modulus maps, and elastic strain maps across a variety of geological and pharmaceutical polycrystals. When possible, the resulting maps will be compared to current homogenization schemes and a full field models. Finite element modeling will be used to assess whether the patterning seen in the experimental map is a reasonable approximation based on the orientation data of the samples used. A minimum of three publications is projected to be accomplished focusing each on a different method to experimentally test and analyze stress distributions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Development of Polycrystalline Photoelectrodes with Optimum Compositions and Morphologies for Solar Fuel Production via Electrochemical Synthesis (Final Technical Report)

Photoelectrochemical cells (PECs) can utilize solar energy for water splitting to produce H 2 as a clean fuel. The most critical components of a water-splitting PEC are semiconductor electrodes (photoelectrodes) that absorb solar energy to generate photoexcited charge carriers and transport them to the electrode/electrolyte interface for water reduction and oxidation reactions. While efficient PEC hydrogen production has been successfully demonstrated on the laboratory scale, the commercial viability of PECs depends critically on the cost of H 2 produced by the PECs, which is affected by the cost of PEC construction. Therefore, identifying promising inexpensive semiconductor electrodes is important. The goal of this project was to bring an advancement in the synthesis and understanding of inexpensive polycrystalline photoelectrodes based on oxides. Oxide-based semiconductors are inexpensive, easy to fabricate, and relatively more stable in aqueous media compared to other types of semiconductors. This project developed new electrodeposition methods to produce a variety of oxide-based semiconductor electrodes with precisely controlled compositions and morphologies to enhance photon absorption, electron-hole separation, and the use of electrons and holes for desired chemical reactions. The resulting high-quality photoelectrodes were investigated to establish the structure-composition-morphology-photoelectrochemical property relationships to identify the advantages and limitations of each oxide semiconductor system.

14 SOLAR ENERGY↗