Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pointing control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

End-point control of a two-link manipulator with a very flexible forearm - Issues and experiments

For mechanical manipulators, a logical sensor location is at the manipulator end-point where tasks are performed. Unfortunately, when bending flexibility exists between an end-point sensor and a joint actuator, stability and performance are achieved only through sophisticated control design. Some of the issues involved in utilizing end-point sensing for two-link flexible manipulators are addressed. A modeling technique that properly represents the foreshortening of a flexible link undergoing deflections is presented. In order to realize fully the advantages of the assumed-modes modeling method, mode shapes are selected that allow a low-order model to be used effectively for simulation and control purposes. A nonlinear controller, incorporating state feedback and a constant-gain extended Kalman filter driven by end-point measurements, is designed and compared to a conventional proportional-plus-derivative controller that uses collocated sensors. Results from implementing these controllers on the experimental Stanford multilink flexible manipulator are given.

Oakley, Celia M.↗
NASA NTRS2005

Terrestrial Planet Finder coronagraph pointing control system design and evaluation for flight baseline 1.

The Terrestrial Planet Finder mission will search for Earth-like, extrasolar planets. The Coronagraph architecture option (TPF-C) will use contrast imaging to suppress the bright starlight in order to detect reflected visible light from the planet. To achieve the required contrast ratio stability of 2e-11, the payload pointing stability must be maintained to better than 4 milli-asec (1σ). The passive TPF-C pointing architecture uses a 3-stage control system combined with a 2- stage passive isolation system to achieve the required pointing accuracy. The active pointing stage includes reaction wheels used for coarse pointing of the spacecraft, a position controlled secondary mirror that provides intermediate alignment, and a Fine Guidance Mirror that provides fine steering control.

Dewell, Larry↗
NASA NTRS1991

A vision-based end-point control for a two-link flexible manipulator

The measurement and control of the end-effector position of a large two-link flexible manipulator are investigated. The system implementation is described and an initial algorithm for static end-point positioning is discussed. Most existing robots are controlled through independent joint controllers, while the end-effector position is estimated from the joint positions using a kinematic relation. End-point position feedback can be used to compensate for uncertainty and structural deflections. Such feedback is especially important for flexible robots. Computer vision is utilized to obtain end-point position measurements. A look-and-move control structure alleviates the disadvantages of the slow and variable computer vision sampling frequency. This control structure consists of an inner joint-based loop and an outer vision-based loop. A static positioning algorithm was implemented and experimentally verified. This algorithm utilizes the manipulator Jacobian to transform a tip position error to a joint error. The joint error is then used to give a new reference input to the joint controller. The convergence of the algorithm is demonstrated experimentally under payload variation. A Landmark Tracking System (Dickerson, et al 1990) is used for vision-based end-point measurements. This system was modified and tested. A real-time control system was implemented on a PC and interfaced with the vision system and the robot.

Obergfell, Klaus↗
NASA NTRS1992

Solar dynamic modules for Space Station Freedom: The relationship between fine-pointing control and thermal loading of the aperture plate

Dynamic simulations of Space Station Freedom (SSF) configured with solar dynamic (SD) power modules were performed. The structure was subjected to Space Shuttle docking disturbances, while being controlled with a 'natural' vibration and tracking control approach. Three control cases were investigated for the purpose of investigating the relationship between actuator effort, SD pointing, and thermal loading on the receiver aperture plate. Transient, one-dimensional heat transfer analyses were performed to conservatively predict temperatures of the multi-layered receiver aperture plate assembly and thermal stresses in its shield layer. Results indicate that the proposed aperture plate is tolerant of concentrated flux impingement during short-lived structural disturbances. Pointing requirements may be loosened and the requirement control torques lessened from that previously specified. Downsizing and simplifying the joint drive system should result in a considerable savings mass.

Quinn, Roger D.↗
NASA NTRS1978

On attitude estimation schemes for fine-pointing control

This paper studies single-axis equations of motion that are applicable to a spacecraft or to a space experiment pointing assembly whose motion has been perfectly isolated from the carrier vehicle. It considers four state estimators for implementation in the control loop for a stellar observation experiment. The first three estimators are very general and do not make use of input torque in their prediction models, while the proposed fourth estimator utilizes this information. It is shown via closed-loop covariance analysis that the best achievable pointing performance with the best of the first three estimators is limited to about 0.125 arc-sec (rms) with the given rate-gyro and star-tracker inaccuracies. It is also shown that the fourth estimator has the capability of achieving a pointing performance far superior to the performance achievable using the first three estimators. The fourth estimator relies on the ability to accurately generate the desired control torque (i.e., low input noise).

Joshi, S. M.↗
NASA NTRS1972

Improvement of a geodetic triangulation through control points established by means of satellite or precision traversing

Whether any significant increment to accuracy could be transferred from a super-control continental net (continental satellite net or super-transcontinental traverse) to the fundamental geodetic net (first-order triangulation) is discussed. This objective was accomplished by evaluating the positional accuracy improvement for a triangulation station, which is near the middle of the investigated geodetic triangulation net, by using various station constraints over its geodetic position. This investigation on a 1858 kilometer long triangulation chain shows that the super-control net can provide a useful constraint to the investigated geodetic triangulation net, and thus can improve it only when the accuracy of super-control net is at least 1 part in 500,000.

Saxena, N. K.↗
DOE OSTI2023

Lower and upper threshold limit for artificial neural network based chilled and condenser water temperatures set-point control in a chilled water system

In this study, an ANN (artificial neural network) based real-time optimized control algorithm for a chilled water cooling system was developed and applied in an actual building to analyze its cooling energy saving effects through in-situ application and actual measurements. For this purpose, the cooling tower’s CndWT (condenser water temperature) and the chiller’s ChWT (chilled water temperature) were set as system control variables. To evaluate algorithm performance, the electric consumption and the COP (coefficient of performance) were compared and analyzed when ChWT and CndWTs were controlled conventionally and controlled based on the ANN. During the analysis, unexpected abnormal data was observed due to insufficient training data and limited consideration of OWBT (outdoor air wet-bulb temperature) when determining the CndWT set-point. Therefore, it is necessary to further build training data from a wider range of conditions and to set the lower limit of CndWT set-point to at least +3.6 °C above OWBT when the OWBT is higher than 23 °C, so that further energy savings can be achieved.

42 ENGINEERING↗
NASA NTRS1973

Fine pointing control, OAO-3

The fine error sensor located within the Princeton Experiment Package (PEP) is designed to aquire a star within its field of view to hold the spacecraft within plus or minus one-tenth of an arc second in pitch, and plus or minus three-arc seconds about the yaw axis. Pointing accuracy and stability tests of the fine error sensor exceeded the plus or minus 0.1 arc second requirement.

Moore, J. V.↗
NASA NTRS1988

Pointing control for LDR

One important aspect of the LDR control problem is the possible excitations of structural modes due to random disturbances, mirror chopping, and slewing maneuvers. An analysis was performed to yield a first order estimate of the effects of such dynamic excitations. The analysis involved a study of slewing jitters, chopping jitters, disturbance responses, and pointing errors, making use of a simplified planar LDR model which describes the LDR dynamics on a plane perpendicular to the primary reflector. Briefly, the results indicate that the command slewing profile plays an important role in minimizing the resultant jitter, even to a level acceptable without any control action. An optimal profile should therefore be studied.

Yam, Y.↗
NASA NTRS1990

Multiple task point control of a redundant manipulator

The kinematic control of a redundant arm based on multiple tasks assigned to different locations of the manipulator is presented. This is equivalent to decomposing a redundant arm into two (or more) nonredundant local arms, the basearm and the forearm, at an intermediate arm location or task point called the elbow. A redundant arm is transformed into a serially cooperating dual-arm system, with the cooperation between the local arms being carried out at the elbow. Then, a manipulator end-effector motion specified by a given task is decomposed into motions of individual local arms as well as an end-effector free motion based on achieving maximum efficiency in task execution. To consider global optimization, elbow control is applied to reshaping and reorientation of a manipulability ellipsoid at the end effector during task execution. The resolved rate control of elbow in the end-effector null and free motion space is used to maximize arm homogeneity and to match the forearm motion space with the task space. Simulation results are shown.

Lee, Sukhan↗
NASA NTRS1981

Pinhole/coronograph pointing control system integration and noise reduction analysis

The Pinhole Occulter Facility (P/OF) is a Space Shuttle based experiment for the production of solar coronographics and hard X-ray images. The system is basically pinhole camera utilizing a deployable 50-m flexible boom for separating the pinholes and coronograph shields from the recording devices located in the Shuttle bay. At the distal end of the boom from the Shuttle is a 25 kg mask containing pinholes and coronograph shields. At the proximal end the detectors are located and mounted, along with the deployable boom, to the ASPS gimbal pointing system (AGS). The mask must be pointed at the Sun with a high degree of pointing stability and accuracy to align the axes of the detectors with the pinholes and shields. Failure to do so will result in a blurring of the images on the detectors and a loss of resolution. Being a Shuttle based experiment, the system will be subjected to the disturbances of the Shuttle. The worst of these is thruster firing for orbit correction; the Shuttle uses a bang-bang thruster control system to maintain orbit to within preset limits. Other disturbances include man motion, motion induced by other systems, and gravity gradient torques.

Greene, M.↗
NASA NTRS1986

Space infrared telescope pointing control system. Infrared telescope tracking in the presence of target motion

The use of charge-coupled-devices, or CCD's, has been documented by a number of sources as an effective means of providing a measurement of spacecraft attitude with respect to the stars. A method exists of defocussing and interpolation of the resulting shape of a star image over a small subsection of a large CCD array. This yields an increase in the accuracy of the device by better than an order of magnitude over the case when the star image is focussed upon a single CCD pixel. This research examines the effect that image motion has upon the overall precision of this star sensor when applied to an orbiting infrared observatory. While CCD's collect energy within the visible spectrum of light, the targets of scientific interest may well have no appreciable visible emissions. Image motion has the effect of smearing the image of the star in the direction of motion during a particular sampling interval. The presence of image motion is incorporated into a Kalman filter for the system, and it is shown that the addition of a gyro command term is adequate to compensate for the effect of image motion in the measurement. The updated gyro model is included in this analysis, but has natural frequencies faster than the projected star tracker sample rate for dim stars. The system state equations are reduced by modelling gyro drift as a white noise process. There exists a tradeoff in selected star tracker sample time between the CCD, which has improved noise characteristics as sample time increases, and the gyro, which will potentially drift further between long attitude updates. A sample time which minimizes pointing estimation error exists for the random drift gyro model as well as for a random walk gyro model.

Powell, J. D.↗
DOE OSTI2024

Data for: A Synoptic System for Capturing Ecosystem Control Points Across Terrestrial-Aquatic Interfaces

The investigation of how climate change and water level fluctuations impact variable and interconnected ecosystems, like the interfaces between terrestrial and aquatic environments, requires the collection and integration of many data types. We describe an integrative and autonomous environmental monitoring approach that uses environmental sensors and data loggers to monitor surface water, groundwater, soil, and vegetation changes and generate essential data for predictive models. We established the network at seven sites along the Chesapeake Bay and Lake Erie coastlines, including a large-scale flood manipulation experiment, collectively generating over three million observations per month. Such sensor networks hold great promise for tracking and comprehending environmental changes where land and water intersect. The sensor system and overall approach to sensor management that we have designed is intended to be widely accessible for research teams spanning in size from an individual investigator to large multi-institution projects. This dataset shows example data generated by the sensor network described above. Data output for data loggers connected to groundwater water quality sondes measuring dissolved oxygen, pH, oxidative redox potential (ORP), groundwater elevation, groundwater salinity and temperature, and groundwater elevation; replicate soil moisture and conductivity probes installed at 10 and 30 cm below the ground surface; rainfall and solar radiation; and mean sap flow from 8 replicate probes. Sensors are installed at upland forest (UP), wetlands (W), and transitional locations between these ecosystems (TR). Example datasets are from Goodwin Islands in the Chesapeake Bay and Portage River along the Lake Erie coastline.

54 ENVIRONMENTAL SCIENCES↗