SEARCH · Engineering Papers

Results for “particle cracking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Effects of short-term over-discharge cycling on the performance of commercial 21,700 lithium-ion cells and the identification of degradation modes

In this paper, short-term over-discharge cycling was performed on commercially available 21,700 lithium-ion cells to investigate its effects on cell performance; the degradation modes were also identified and analyzed in detail using both in-situ and ex-situ methods. Results show that observable capacity loss occurs when the cell is over-discharged to 112.5% depth of discharge. Moreover, the negative impact of the depth of discharge on cell performance (or cell aging) is more serious than the number of cycles, and continuous over-discharge cycling will accumulate such impact. The loss of Li inventory related to the decomposition and reformation of solid electrolyte interphase film is an important cause of the irreversible capacity loss/degradation of Li-ion cells during over-discharge cycling testing. Furthermore, the dissolution of copper current collector can greatly reduce the mechanical stability of the anode, and further, the deposition of Cu, the exfoliation and the cracking of active material particles can influence the transfer of ions and lead to the loss of Li inventory and the loss of active material within Li-ion cells. Additionally, when the depth of discharge exceeds 108.3%, deposition of Cu is observed on the ceramic-covered side of separators.

25 ENERGY STORAGE↗

DOE OSTI2020

Influence of copper content on the high temperature tensile and low cycle fatigue behavior of cast Al-Cu-Mn-Zr alloys

The relationship between low cycle fatigue (LCF) and monotonic tensile fracture strain was investigated for cast Al-Cu-Mn-Zr alloys containing 6 and 9 wt% Cu at 250 °C. The 9% Cu alloy consisted of larger size and volume fraction of brittle intermetallic grain boundary particles that fractured during tensile tests to reduce the fracture strain by 50% compared to the 6% Cu alloy. We found that LCF life was similar between the two alloys and weakly influenced by the particles. LCF life and fracture strain were poorly correlated due to the dominant influence of particles on monotonic tensile crack but not on fatigue crack.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Methods—Kintsugi Imaging of Battery Electrodes: Distinguishing Pores from the Carbon Binder Domain using Pt Deposition

The mesostructure of porous electrodes used in lithium-ion batteries strongly influences cell performance. Accurate imaging of the distribution of phases in these electrodes would allow this relationship to be better understood through simulation. However, imaging the nanoscale features in these components is challenging. While scanning electron microscopy is able to achieve the required resolution, it has well established difficulties imaging porous media. This is because the flat imaging planes prepared using focused ion beam milling will intersect with the pores, which makes the images hard to interpret as the inside walls of the pores are observed. It is common to infiltrate porous media with resin prior to imaging to help resolve this issue, but both the nanoscale porosity and the chemical similarity of the resins to the battery materials undermine the utility of this approach for most electrodes. In this study, a technique is demonstrated which uses in situ infiltration of platinum to fill the pores and thus enhance their contrast during imaging. Reminiscent of the Japanese art of repairing cracked ceramics with precious metals, this technique is referred to as the kintsugi method. The images resulting from applying this technique to a conventional porous cathode are presented and then segmented using a multi-channel convolutional method. We show that while some cracks in active material particles were empty, others appear to be filled (perhaps with the carbon binder phase), which will have implications for the rate performance of the cell. Energy dispersive X-ray spectroscopy was used to validate the distribution of phases resulting from image analysis, which also suggested a graded distribution of the binder relative to the carbon additive. The equipment required to use the kintsugi method is commonly available in major research facilities and so we hope that this method will be rapidly adopted to improve the imaging of electrode materials and porous media in general.

25 ENERGY STORAGE↗

NASA NTRS1986

Interfaces and failure mechanisms in Al-SiC composites

Aluminum alloys reinforced with silicon carbide whiskers exhibit significantly higher strength and modulus than the unreinforced alloys. However, the composites also exhibit low ductility and poor fracture toughness for reasons which are not well-understood. In this study, high resolution and conventional TEM techniques are used to analyze interface microstructure and failure mechanisms in P/M 2124 and 6061 aluminum alloys reinforced with silicon carbide whiskers. Interfacial oxides are typical of both composite materials, often distributed in clusters or in a discrete layer 2-5 nm thick along the whisker-matrix interface. Highly deformed regions beneath bulk tensile fracture surfaces reveal possible fracture nucleation centers as well as sites of stress concentration where intense plastic strain has occurred. Observations of such highly deformed regions include (1) void initiation at whisker ends, (2) interface decohesion involving the thin oxide layer, (3) transverse cracks in whiskers, and (4) cracks in large constituent particles. TEM results are presented and discussed in relation to mechanisms of composite failure.

Nutt, S. R.↗

DOE OSTI2022

Exposed Kernel Heating Tests

Presentation on cracked AGR-2 TRISO particles and AGR-3/4 compacts subjected to FACS tests with and without prior reirradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

A hydride model for solid and liquid cerium ejecta particles

Cerium ejecta particles form after a shock wave impacts a cerium plate with a rough surface or prescribed surface perturbation. When these particles are ejected into hydrogen or deuterium gas the material reacts exothermically and raises the temperature of the particle. Two models are developed to capture the heat and mass transfer that occurs during this process. One model assumes that for larger solid ejecta particles, the loss of mass is negligible while for smaller liquid ejecta particles, the loss of mass during reaction is accounted for. The loss of mass is assumed to occur from the hydride layer being extremely brittle and the fact that it will be relatively easy for the hydride material on the outside of the particle to go into tension, crack and flake off. The model is tested by performing simulations similar to the original experiments that motivated the development of these models and comparing the particle temperatures. While the model is able to capture some general features of the flowfield, inaccuracies clearly exist that must be addressed and the results underscore the need for more isolated experiments where fewer assumptions and physical processes are present simultaneously.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2014

Progress of a Cross-Correlation Based Optical Strain Measurement Technique for Detecting Radial Growth on a Rotating Disk

The Aeronautical Sciences Project under NASA's Fundamental Aeronautics Program is interested in the development of novel measurement technologies, such as optical surface measurements for the in situ health monitoring of critical constituents of the internal flow path. In situ health monitoring has the potential to detect flaws, i.e. cracks in key components, such as engine turbine disks, before the flaws lead to catastrophic failure. The present study, aims to further validate and develop an optical strain measurement technique to measure the radial growth and strain field of an already cracked disk, mimicking the geometry of a sub-scale turbine engine disk, under loaded conditions in the NASA Glenn Research Center's High Precision Rotordynamics Laboratory. The technique offers potential fault detection by imaging an applied high-contrast random speckle pattern under unloaded and loaded conditions with a CCD camera. Spinning the cracked disk at high speeds (loaded conditions) induces an external load, resulting in a radial growth of the disk of approximately 50.0-μm in the flawed region and hence, a localized strain field. When imaging the cracked disk under static conditions, the disk will be undistorted; however, during rotation the cracked region will grow radially, thus causing the applied particle pattern to be 'shifted'. The resulting particle displacements between the two images is measured using the two-dimensional cross-correlation algorithms implemented in standard Particle Image Velocimetry (PIV) software to track the disk growth, which facilitates calculation of the localized strain field. A random particle distribution is adhered onto the surface of the cracked disk and two bench top experiments are carried out to evaluate the technique's ability to measure the induced particle displacements. The disk is shifted manually using a translation stage equipped with a fine micrometer and a hotplate is used to induce thermal growth of the disk, causing the particles to become shifted. For both experiments, reference and test images are acquired before and after the induced shifts, respectively, and then processed using PIV software. The controlled manual translation of the disk resulted in detection of the particle displacements accurate to ~1.75% of full scale and the thermal expansion experiment resulted in successful detection of the disk's thermal growth as compared to the calculated thermal expansion results. After validation of the technique through the induced shift experiments, the technique is implemented in the Rotordynamics Lab for preliminary assessment in a simulated engine environment. The discussion of the findings and plans for future work to improve upon the results are addressed in the paper.

rotordynamics↗

NASA NTRS1990

Elevated temperature crack growth in advanced powder metallurgy aluminum alloys

Rapidly solidified Al-Fe-V-Si powder metallurgy alloy FVS0812 is among the most promising of the elevated temperature aluminum alloys developed in recent years. The ultra fine grain size and high volume fraction of thermally stable dispersoids enable the alloy to maintain tensile properties at elevated temperatures. In contrast, this alloy displays complex and potentially deleterious damage tolerant and time dependent fracture behavior that varies with temperature. J-Integral fracture mechanics were used to determine fracture toughness (K sub IC) and crack growth resistance (tearing modulus, T) of extruded FVS0812 as a function of temperature. The alloy exhibits high fracture properties at room temperature when tested in the LT orientation, due to extensive delamination of prior ribbon particle boundaries perpendicular to the crack front. Delamination results in a loss of through thickness constraint along the crack front, raising the critical stress intensity necessary for precrack initiation. The fracture toughness and tensile ductility of this alloy decrease with increasing temperature, with minima observed at 200 C. This behavior results from minima in the intrinsic toughness of the material, due to dynamic strain aging, and in the extent of prior particle boundary delaminations. At 200 C FVS0812 fails at K levels that are insufficient to cause through thickness delamination. As temperature increases beyond the minimum, strain aging is reduced and delamination returns. For the TL orientation, K (sub IC) decreased and T increased slightly with increasing temperature from 25 to 316 C. Fracture in the TL orientation is governed by prior particle boundary toughness; increased strain localization at these boundaries may result in lower toughness with increasing temperature. Preliminary results demonstrate a complex effect of loading rate on K (sub IC) and T at 175 C, and indicate that the combined effects of time dependent deformation, environment, and strain aging may play a role. Fractography showed that microvoid coalescence was the microscopic mode of fracture in FVS0812 under all testing conditions. However, the nature of the microvoids varied with test temperature and loading rate, and is complex for the fine grain and dipersoid sizes of FVS0812.

Porr, William C., Jr.↗

NASA NTRS1997

Analytical Modeling of Pressure Wall Hole Size and Maximum Tip-to-Tip Crack Length for Perforating Normal and Oblique Orbital Debris Impacts

This report presents the results of a study whose objective was to develop first-principles-based models of hole size and maximum tip-to-tip crack length for a spacecraft module pressure wall that has been perforated in an orbital debris particle impact. The hole size and crack length models are developed by sequentially characterizing the phenomena comprising the orbital debris impact event, including the initial impact, the creation and motion of a debris cloud within the dual-wall system, the impact of the debris cloud on the pressure wall, the deformation of the pressure wall due to debris cloud impact loading prior to crack formation, pressure wall crack initiation, propagation, and arrest, and finally pressure wall deformation following crack initiation and growth. The model development has been accomplished through the application of elementary shock physics and thermodynamic theory, as well as the principles of mass, momentum, and energy conservation. The predictions of the model developed herein are compared against the predictions of empirically-based equations for hole diameters and maximum tip-to-tip crack length for three International Space Station wall configurations. The ISS wall systems considered are the baseline U.S. Lab Cylinder, the enhanced U.S. Lab Cylinder, and the U.S. Lab Endcone. The empirical predictor equations were derived from experimentally obtained hole diameters and crack length data. The original model predictions did not compare favorably with the experimental data, especially for cases in which pressure wall petalling did not occur. Several modifications were made to the original model to bring its predictions closer in line with the experimental results. Following the adjustment of several empirical constants, the predictions of the modified analytical model were in much closer agreement with the experimental results.

Schonberg, William P.↗

DOE OSTI2025

Microstructure Scale Lithium-Ion Battery Modeling: Part III. When and Where Lithium Plating Occurs and its Correlation with the Electrode Microstructure

Li-ion battery performance and degradation are closely related to the cell’s underlying electrode microstructure. Electrode microstructures are typically characterized with volume-averaged properties that neglect the impact of local heterogeneities. However, local heterogeneities create hot spots that can trigger degradation onset. Herein, a microstructure scale electrochemical model is used to investigate the impact of microstructure heterogeneity on lithium plating. The model predicts lithium plating is not uniform, even when considering a relatively small portion of the electrode (a cross-sectional area of 154×144 µm 2 ), preferring to plate on larger particles as compared to smaller particles. While local heterogeneities control where plating occurs, the model predicts that volume-averaged properties control when plating occurs. Additionally, the model predicts that the active material specific surface area has a linear relationship with the plating onset. However, the linear relationship between increased active material surface area and delayed plating response appears to be sensitive to the microstructure feature used to increase the active interface area. Here, a comparative case-study is explored where the specific surface area is increased by either reducing the active material particle diameter, adding open-porosity cracks, or increasing the active material surface roughness. The model predicts that increasing the specific surface area by reducing the active material particle diameter is the most effective strategy for delaying lithium plating. At 6C, reducing particle size is shown to be 3 and 20 times more effective than, respectively, adding open-porosity cracks and increasing surface roughness. A dual-layer electrode architecture combining gradations both for average properties and uniformities is eventually proposed to improve homogeneous material utilization and reduce degradation at high charge rates.

25 ENERGY STORAGE↗

NASA NTRS1972

Ductile-brittle transition of thoriated chromium.

Unalloyed chromium and chromium containing approximately 3 wt % ThO2 were prepared from powder produced by a chemical vapor deposition process. When rolled to sheet and tested in tension, it was found that the thoriated material had a lower ductile-to-brittle transition temperature (DBTT) than unalloyed chromium. This ductilizing was evident both in the as-rolled condition and after the materials had been annealed for 1 hour at 1200 C. The improved ductility in thoriated chromium may be associated with several possible mechanisms: (1) particles may disperse slip, such that critical stress or strain concentrations for crack nucleation are more difficult to achieve; (2) particles may act as dislocation sources, thus providing mobile dislocations in this normally source-poor material, in a manner similar to prestraining; and (3) particles in grain boundaries may help to transmit slip across the boundaries, thus relieving stress concentrations and inhibiting crack nucleation.

Wilcox, B. A.↗

DOE OSTI2024

Image-Based Digital Twin for Assessing the Coupled Electro-Chemo-Mechanical Behavior of Li-Ion Batteries

In energy storage materials, strong electrochemical-mechanical coupling and highly anisotropic material properties contribute to the formation and propagation of micro-cracking during charge/discharge cycling, resulting in reduced performance and service life. In this work, a digital twin is created to investigate the performance of a Li-ion battery cathode and simulate degradation accumulation. Pixel-based model construction is used to represent the complex material geometries from microstructural images supplied by the National Renewable Energy Laboratory (NREL). Because of the expected large deformation and crack opening, the reproducing kernel particle method (RKPM), a meshfree method with discretization at the image pixels, is used to approximate the field variables: electrostatic potential, concentration, and displacement. An interface modified reproducing kernel (IM-RK) is constructed by scaling a smooth kernel function with an interface-distance function to achieve strategic discontinuity types (i.e. weak discontinuities for strain discontinuities and strong discontinuities for cracks) and alleviate Gibbs oscillations near these transition zones. The discrete nature of the images' pixel points is employed throughout the model and approximation construction. The mechanical model is verified using an image-based microstructure under tensile loading. A transient electro-chemo-mechanical coupled simulation is performed to evaluate the potential micro-cracking induced degradation of the battery cathode material subjected to charge/discharge cycling.

battery degradation↗

DOE OSTI2024

Image-Based Failure Assessment of Li-Ion Batteries

In energy storage materials, strong electrochemical-mechanical coupling and highly anisotropic material properties contribute to the formation and propagation of micro-cracking during charge/discharge cycling, resulting in reduced performance and service life. In this work, a digital twin is created to investigate the performance of a heterogeneous Li-ion battery cathode and simulate degradation accumulation. Pixel-based model construction is used to represent the complex material geometries from microstructural images supplied by the National Renewable Energy Laboratory (NREL). Because of the expected large deformation and crack opening, the reproducing kernel particle method (RKPM), a meshfree method with discretization at the image pixels, is used to approximate the field variables: electrostatic potential, concentration, and displacement. An interface modified reproducing kernel (IM-RK) is constructed by scaling a smooth kernel function with an interface-distance function to achieve strategic discontinuity types (i.e. weak discontinuities for strain discontinuities and strong discontinuities for cracks) and alleviate Gibbs oscillations near these transition zones. Applications to the heterogeneous microstructures of Li-ion battery cathodes will be presented to demonstrate the effectiveness of the proposed methods. IM-RK is additionally used to inform how crack evolution in turn affects the coupled electro-chemo-mechanical behavior of the Li-ion battery cathode.

image-based modeling↗

NASA NTRS2007

Automated Eddy Current Inspection on Space Shuttle Hardware

Over the life time of the Space Shuttle program, metal parts used for the Reusable Solid Rocket Motors (RSRMs) have been nondestructively inspected for cracks and surface breaking discontinuities using magnetic particle (steel) and penetrant methods. Although these inspections adequately screened for critical sized cracks in most regions of the hardware, it became apparent after detection of several sub-critical flaws that the processes were very dependent on operator attentiveness and training. Throughout the 1990's, eddy current inspections were added to areas that had either limited visual access or were more fracture critical. In the late 1990's. a project was initiated to upgrade NDE inspections with the overall objective of improving inspection reliability and control. An automated eddy current inspection system was installed in 2001. A figure shows one of the inspection bays with the robotic axis of the system highlighted. The system was programmed to inspect the various case, nozzle, and igniter metal components that make up an RSRM. both steel and aluminum. For the past few years, the automated inspection system has been a part of the baseline inspection process for steel components. Although the majority of the RSRM metal part inventory ts free of detectable surface flaws, a few small, sub-critical manufacturing defects have been detected with the automated system. This paper will summarize the benefits that have been realized with the current automated eddy current system, as well as the flaws that have been detected.

Hartmann, John↗

DOE OSTI2023

Meshfree Multiphysics Damage Modeling of Li-ion Battery Materials

Through repeated charging and discharging cycles, the electrodes of a Li-ion battery experience significant swelling and contraction due to the movement of lithium, also known as intercalation. This research focuses specifically on the chemo-mechanical cracking in the cathode. Because cathode particles are comprised of many randomly-oriented grains, which have highly anisotropic material properties, the expansion and contraction is very non-uniform. As a result, stress concentrations tend to form between grains, which necessitates the modeling of crack propagation largely along grain boundaries and material interfaces. Chemo-mechanical damage models are generally simulated by one of two methods: the cohesive zone model (CZM) and the continuous damage model (CDM). The CZM is more accurate at capturing the sharp discontinuities of a crack but is very computationally expensive and intractable for large-scale models as a result. Conversely, the CDM is easily computed but not well-suited to easily allow for discontinuous field variables, which are inherent across a crack. This study aims to improve the CDM's ability to capture discontinuous cracks. Current versions of the CDM use the finite element method (FEM), which is one of the most widely used approaches for spatial discretization. This research investigates the use of the Reproducing Kernel Particle Method (RKPM), a meshfree method, for spatial discretization and aims to achieve a coupled chemo-mechanical crack propagation model that enhances accuracy while maintaining high computational efficiency. This model features a fully coupled, iterative electrochemistry solution, which informs the meshfree damage model of impending crack formation. To gain a better understanding of how the meshfree model compares to the current FEM model in capturing cathode crack propagation, further investigation is needed.

damage modeling↗

DOE OSTI2023

Ultrafine-grained Fe-TiB 2 high-modulus nanocomposite steel with high strength and isotropic mechanical properties by laser powder bed fusion

Fe-TiB 2 metal matrix composite, also called high-modulus steels (HMSs), are of great interest for applications in fuel-efficient transportation infrastructure, aerospace, and wear industries due to their high specific stiffness and yield strength. However, conventional cast Fe-TiB 2 HMSs often contain coarse and sharp-edged TiB 2 particles which easily trigger premature cracking during loading. Here, we synthesized a Fe-TiB 2 nanocomposite HMS via laser powder bed fusion (LPBF) additive manufacturing of mixed micro-sized powders of Fe, Ti, and Fe 2 B. We investigated the microstructure formation and mechanical behavior of the Fe-TiB 2 HMS. We found that in situ chemical reaction of Ti and Fe 2 B enables the formation of TiB 2 particles at nanoscale during rapid solidification of LPBF. These nanoscale TiB 2 particles can serve as heterogeneous nucleation sites and promote the formation of ultrafine and equiaxed α-Fe grains with random crystallographic textures, which differ from many other additively manufactured (AM) metal alloys characteristic of strong crystallographic textures. As such, isotropic mechanical properties were achieved in the AM Fe-TiB 2 nanocomposite HMS with a high elastic modulus of ~ 240 GPa, an exceptional yield strength of ~ 1450 MPa, and a large plasticity of ~ 20% under compression. Quantitative analysis reveals that the high yield strength primarily originates from strengthening contributions of the ultrafine grains with an average grain size of ~450 nm, the nanoscale TiB 2 reinforcing particles of 20–180 nm, and a high density of printing-induced dislocations of the order of 10 15 m –2 . In situ synchrotron high-energy X-ray diffraction unveils the load partitioning from the softer α-Fe matrix to the stiffer and stronger TiB 2 nanoparticles, contributing to the sustained strain hardening during compression. Our work not only provides a general pathway for achieving high-performance metal matrix nanocomposites by in situ chemical reaction and precipitation of ceramic nanoparticles during additive manufacturing, but also offers mechanistic insights into the deformation mechanism of nanoparticle-reinforced HMS composites.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Meshfree Methods for Modeling Chemo-Mechanical Cathode Cracking in Li-Ion Batteries

Through repeated charging and discharging, the electrodes of a Li-ion battery experience cyclic loading causing swelling and contraction due to the movement of lithium, also known as intercalation. This research focuses specifically on the chemo-mechanical cracking in the cathode. Because cathode particles are comprised of many randomly-oriented grains, which have highly anisotropic material properties, the expansion and contraction is very non-uniform. As a result, stress concentrations tend to form between grains, which necessitates the modeling of crack propagation largely along grain boundaries. Chemo-mechanical models are simulated mainly by two methods: the cohesive zone model (CZM) and the continuous damage model (CDM). The CZM is more accurate at capturing the sharp discontinuities of a crack but is very computationally expensive and intractable for large-scale models as a result. Conversely, the CDM is easily computed but not well-suited to easily allow for discontinuous field variables, which are inherent across a crack. This study aims to improve the CDM's ability to capture discontinuous cracks. Current versions of the CDM use the finite element method (FEM), which is one of the most widely used approaches for spatial discretization. This research investigates the use of the Reproducing Kernel Particle Method (RKPM), a meshfree method, for spatial discretization and aims to achieve a chemo-mechanical crack propagation model that achieves both intermediate accuracy and computational time between a CDM and CZM. To gain a better understanding of how the meshfree model compares to the current FEM model in capturing cathode crack propagation, further investigation is needed.

cathode cracking↗

NASA NTRS1994

Corrosion and corrosion fatigue of airframe aluminum alloys

Localized corrosion and corrosion fatigue crack nucleation and growth are recognized as degradation mechanisms that effect the durability and integrity of commercial transport aircraft. Mechanically based understanding is needed to aid the development of effective methodologies for assessing durability and integrity of airframe components. As a part of the methodology development, experiments on pitting corrosion, and on corrosion fatigue crack nucleation and early growth from these pits were conducted. Pitting was found to be associated with constituent particles in the alloys and pit growth often involved coalescence of individual particle-nucleated pits, both laterally and in depth. Fatigue cracks typically nucleated from one of the larger pits that formed by a cluster of particles. The size of pit at which fatigue crack nucleates is a function of stress level and fatigue loading frequency. The experimental results are summarized, and their implications on service performance and life prediction are discussed.

Chen, G. S.↗