Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parameter compensation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Modulation and synchronization technique for MF-TDMA system

This report addresses modulation and synchronization techniques for a multi-frequency time division multiple access (MF-TDMA) system with onboard baseband processing. The types of synchronization techniques analyzed are asynchronous (conventional) TDMA, preambleless asynchronous TDMA, bit synchronous timing with a preamble, and preambleless bit synchronous timing. Among these alternatives, preambleless bit synchronous timing simplifies onboard multicarrier demultiplexer/demodulator designs (about 2:1 reduction in mass and power), requires smaller onboard buffers (10:1 to approximately 3:1 reduction in size), and provides better frame efficiency as well as lower onboard processing delay. Analysis and computer simulation illustrate that this technique can support a bit rate of up to 10 Mbit/s (or higher) with proper selection of design parameters. High bit rate transmission may require Doppler compensation and multiple phase error measurements. The recommended modulation technique for bit synchronous timing is coherent QPSK with differential encoding for the uplink and coherent QPSK for the downlink.

Faris, Faris↗
NASA NTRS2006

Development of Laser Fabricated Ti-6Al-4V

Laser Engineered Net Shaping (LENS) depositions with Ti-6Al-4V gas-atomized powder were accomplished at five different temperatures, ranging from 30 to 400 C, imposed on the base plate. These base plate temperatures were employed in an effort to relieve stresses which develop during the deposition. Warpage of the base plate was monitored. Only a slight decline in warpage was observed as the base plate temperature was increased. Results indicate that substrate temperatures closer to the stress relief minimum of 480 C would relieve deposition stresses, though process parameters would likely need to be modified to compensate for the higher base plate temperature. The compositions of the as-received powder and the LENS deposited material were chemically analyzed. The oxygen content of the LENS material was 0.154 wt.% which is less than the maximum impurity limit of 0.2 percent for commercial Ti-6Al-4V alloys, but is over the limit allowed in ELI grade (0.13 percent). The level of oxygen in the commercial base plate used was only 0.0635 percent. Tensile specimens were machined from the LENS deposited material and tested in tension at room temperature. The ultimate and yield tensile stresses of the LENS material were about 1200 and 1150 MPa respectively, which is about 20 percent higher than the strengths of wrought Ti-6Al-4V. The higher strength of the LENS material was due to its fine structure and high oxygen content. The LENS deposits were not fully dense; voids were frequent at the interfaces between deposited layers. These dispersed sheets of voids were parallel to the longitudinal axis of the resulting tensile specimens. Apparently there was sufficient continuous, fully dense material longitudinally to enable the high strengths. Ductility was low in the LENS material. Percent elongation at failure in the LENS material was near 4 percent, which is less than half of what is usually expected from Ti-6Al-4V. The low ductility was caused by high oxygen levels, and the presence of voids. It is likely that the relatively high scan speeds used in our depositions contributed to the lack of full density in our LENS material.

deGroh, Henry C., III↗
NASA NTRS2009

Pitch-Axis Aerodynamic Parameter Identification for NASA's F-15B

As part of NASA s Intelligent Flight Control Systems program, parameter identification experiments were carried out with NASA Dryden s F-15B TN 837 aircraft. The canard control surfaces, whose movement is highly correlated with aircraft angle of attack, and the aircraft s aerodynamic instability in the pitch axis contribute to making parameter identification challenging. The equation-error method of analysis is applied to several longitudinal parameter identification maneuvers and a new approach for compensating for flight-data signal time lags is developed, which improves the accuracy and consistency of the results.

Woodruff, Stephen L.↗
DOE OSTI2024

Photosynthetic responses of switchgrass to light and CO 2 under different precipitation treatments

Switchgrass ( Panicum virgatum L .) is a prominent bioenergy crop with robust resilience to environmental stresses. However, our knowledge regarding how precipitation changes affect switchgrass photosynthesis and its responses to light and CO 2 remains limited. To address this knowledge gap, we conducted a field precipitation experiment with five different treatments, including −50%, −33%, 0%, +33%, and +50% of ambient precipitation. To determine the responses of leaf photosynthesis to CO 2 concentration and light, we measured leaf net photosynthesis of switchgrass under different CO 2 concentrations and light levels in 2020 and 2021 for each of the five precipitation treatments. We first evaluated four light and CO 2 response models (i.e., rectangular hyperbola model, nonrectangular hyperbola model, exponential model, and the modified rectangular hyperbola model) using the measurements in the ambient precipitation treatment. Based on the fitting criteria, we selected the nonrectangular hyperbola model as the optimal model and applied it to all precipitation treatments, and estimated model parameters. Overall, the model fit field measurements well for the light and CO 2 response curves. Precipitation change did not influence the maximum net photosynthetic rate ( P max ) but influenced other model parameters including quantum yield ( α ), convexity ( θ ), dark respiration ( Rd ), light compensation point ( LCP ), and saturated light point ( LSP ). Specifically, the mean P max of five precipitation treatments was 17.6 μmol CO 2 m −2 s −1 , and the ambient treatment tended to have a higher P max . The +33% treatment had the highest α , and the ambient treatment had lower θ and LCP , higher Rd , and relatively lower LSP . Furthermore, precipitation significantly influenced all model parameters of CO 2 response. The ambient treatment had the highest P max , largest α , and lowest θ , R d , and CO 2 compensation point LCP . Overall, this study improved our understanding of how switchgrass leaf photosynthesis responds to diverse environmental factors, providing valuable insights for accurately modeling switchgrass ecophysiology and productivity.

09 BIOMASS FUELS↗
NASA NTRS1993

Tetravalent chromium (Cr(4+)) as laser-active ion for tunable solid-state lasers

Major accomplishments under NASA grant NAG-1-1346 are summarized. (1) numerical modeling of the four mirror astigmatically compensated, Z-fold cavity was performed and several design parameters to be used for the construction of a femtosecond forsterite laser were revealed by simulation. (2) femtosecond pulses from a continuous wave mode-locked chromium doped forsterite laser were generated. The forsterite laser was actively mode-locked using an acousto-optic modulator operating at 78 MHz with two Brewster high dispersion glass prisms for intra-cavity chirp compensation. Transform-limited sub-100-fs pulses were routinely generated in the TEM(sub 00) mode with 85 mW of continuous power tunable over 1230-1280 nm. The shortest pulses of 60-fs pulsewidth were measured. (3) Self-mode-locked operation of the Cr:forsterite laser was achieved. Synchronous pumping was used to mode lock the forsterite laser resulting in picosecond pulses, which in turn provided the starting mechanism for self-mode-locking. The pulses generated had an FWHM of 105 fs and were tunable between 1230-1270 nm. (4) Numerical calculations indicated that the pair of SF 14 prisms used in the cavity compensated for quadratic phase but introduced a large cubic phase term. Further calculations of other optical glasses indicated that a pair of SFN 64 prisms can introduce the same amount of quadratic phase as SF 14 prisms but introduce a smaller cubic phase. When the SF 14 prisms were replaced by SFN 64 prisms the pulsewidth was reduced to 50 fs. Great improvement was observed in the stability of the self mode-locked forsterite laser and in the ease of achieving mode locking. Using the same experimental arrangement and a new forsterite crystal with improved FOM the pulse width was reduced to 36 fs.

Seas, A.↗
NASA NTRS1971

Optimal limited state variable feedback controllers for linear systems.

Optimized static and dynamic linear system compensator designs with a priori fixed dimensions are discussed. Expressions are derived to determine the parameters of these designs, including the fixed-gain output feedback, the time-varying output feedback, and time-invariant compensation. A relevant deterministic off-line optimization problem is formulated, and the properties of a solution to the problem are analyzed. A unified design philosophy for limited state-variable control problems of essentially deterministic systems is developed. The philosophy incorporates design constraints, a careful selection of performance criteria, and interpretation of the results.

Levine, W. S.↗
NASA NTRS1998

Assessment Study of the State of the Art in Adaptive Control and its Applications to Aircraft Control

Many papers relevant to reconfigurable flight control have appeared over the past fifteen years. In general these have consisted of theoretical issues, simulation experiments, and in some cases, actual flight tests. Results indicate that reconfiguration of flight controls is certainly feasible for a wide class of failures. However many of the proposed procedures although quite attractive, need further analytical and experimental studies for meaningful validation. Many procedures assume the availability of failure detection and identification logic that will supply adequately fast, the dynamics corresponding to the failed aircraft. This in general implies that the failure detection and fault identification logic must have access to all possible anticipated faults and the corresponding dynamical equations of motion. Unless some sort of explicit on line parameter identification is included, the computational demands could possibly be too excessive. This suggests the need for some form of adaptive control, either by itself as the prime procedure for control reconfiguration or in conjunction with the failure detection logic. If explicit or indirect adaptive control is used, then it is important that the identified models be such that the corresponding computed controls deliver adequate performance to the actual aircraft. Unknown changes in trim should be modelled, and parameter identification needs to be adequately insensitive to noise and at the same time capable of tracking abrupt changes. If however, both failure detection and system parameter identification turn out to be too time consuming in an emergency situation, then the concepts of direct adaptive control should be considered. If direct model reference adaptive control is to be used (on a linear model) with stability assurances, then a positive real or passivity condition needs to be satisfied for all possible configurations. This condition is often satisfied with a feedforward compensator around the plant. This compensator must be robustly designed such that the compensated plant satisfies the required positive real conditions over all expected parameter values. Furthermore, with the feedforward only around the plant, a nonzero (but bounded error) will exist in steady state between the plant and model outputs. This error can be removed by placing the compensator also in the reference model. Design of such a compensator should not be too difficult a problem since for flight control it is generally possible to feedback all the system states.

Kaufman, Howard↗
NASA NTRS1955

Analog Study of Interacting and Noninteracting Multiple-loop Control Systems for Turbojet Engines

The results of an analog investigation of several turbojet-engine control configurations is presented in this report. Both proportional and proportional-plus-integral controllers were studied, and compensating terms for engine interaction were added to the control system. Data were obtained on the stability limits and the transient responses of these various configurations. Analytical expressions in terms of the component transfer functions were developed for the configurations studied, and the optimum form for the compensation terms was determined. It was found that the addition of the integral term, while making the system slower and more oscillatory, was desirable in that it made the final values of the system parameters independent of source of disturbance and also eliminated droop in these parameters. Definite improvement in system characteristics resulted from the use of proper compensation terms. At comparable gain points the compensated system was faster and more stable. Complete compensation eliminated engine interaction, permitting each loop to be developed to an optimum point independently.

Pack, George J↗
DOE OSTI2020

Filtering adaptive output feedback control for multivariable nonlinear systems with mismatched uncertainties and unmodeled dynamics

This article synthesizes a filtering adaptive output feedback controller for multivariable nonlinear systems with mismatched uncertainties and unmodeled dynamics. The multivariable nonlinear systems under consideration have both matched and mismatched uncertainties, which satisfy the semiglobal Lipschitz condition. The unmodeled dynamics are bounded-input bounded-output stable. By adopting an estimation/cancellation strategy, a piecewise constant adaptive law drives the estimation error to zero at every time instant, which yields the adaptive parameters; a disturbance rejection control law is designed to compensate the nonlinear uncertainties within the bandwidth of low-pass filters. The matched uncertainties are cancelled directly by adopting their opposite in the control signal, while a dynamic inversion of the system is required to eliminate the effect of the mismatched uncertainties on the output. A feedforward control law is designed to track a given command. Since the virtual reference system defines the best performance that can be achieved by the closed-loop system, the uniform performance bounds are derived for the states and control signals via comparison. Both numerical and practical examples are provided to illustrate the effectiveness of the proposed filtering adaptive output feedback control architecture, comparisons with the model reference adaptive control demonstrates the superiority of the proposed control method.

filtering adaptive control, mismatched uncertainit↗
NASA NTRS1975

Boost navigation and guidance

The verification that the boost mode portion of the flight program correctly provides navigation and guidance functions for the vehicle during periods when significant, measurable accelerations exist was described. Many test cases and performance cases are made, testing the ability of the navigation and guidance routines to properly compensate for several perturbations. Various plots of special interest parameters are made on all performance cases, facilitating a check on each calculation (each boost major loop) of these parameters.

Source record↗
NASA NTRS1993

Optimal fixed-finite-dimensional compensator for Burgers' equation with unbounded input/output operators

The problem of using reduced order dynamic compensators to control a class of nonlinear parabolic distributed parameter systems was considered. Concentration was on a system with unbounded input and output operators governed by Burgers' equation. A linearized model was used to compute low-order-finite-dimensional control laws by minimizing certain energy functionals. Then these laws were applied to the nonlinear model. Standard approaches to this problem employ model/controller reduction techniques in conjunction with linear quadratic Gaussian (LQG) theory. The approach used is based on the finite dimensional Bernstein/Hyland optimal projection theory which yields a fixed-finite-order controller.

Burns, John A.↗
NASA NTRS1990

Formulation of a minimum variance deconvolution technique for compensation of pneumatic distortion in pressure sensing devices

Increasingly, aircraft system designs require that aerodynamic parameters derived from pneumatic measurements be employed as control-system feedbacks. Such high frequency pressure measurements' accuracy is compromised by pressure distortion due to frictional attenuation and pneumatic resonance within the sensing system. A pneumatic distortion model is here formulated and reduced to a low-order state-variable model which retains most of the full model's dynamic characteristics. This reduced-order model is coupled with standard results from minimum variance estimation theory to develop an algorithm to compensate for pneumatic-distortion effects.

Whitmore, Stephen A.↗
NASA NTRS2003

LPV Antiwindup Compensation for Enhanced Flight Control Performance

In this paper, we propose a saturation control scheme for linear parameter-varying (LPV) systems from an antiwindup control perspective. The proposed control approach is advantageous because it can be thought of as an augmented control algorithm from the existing control system. Moreover, the synthesis condition for an antiwindup compensator is formulated as a linear matrix inequality (LMI) optimization problem and can be solved efficiently. We have applied the LPV antiwindup controller to an F-16 longitudinal autopilot control system design to enhance aircraft safety and improve flight quality in a high angle of attack region.

Lu, Bei↗
DOE OSTI2021

On the possibility of footprint compression with one lens in nonlinear accelerator lattice

Electromagnetic interaction of colliding beams along with other nonlinear fields often limits the beams' lifetimes and luminosities. Nonlinearities result in the spread of betatron frequencies (footprint) and, thus, may enhance dynamic diffusion of particles due to high order resonances. One of the possible ways to eliminate nonlinearities and overcome the corresponding difficulties is compensation of nonlinear forces, but, in practice, it is hardly possible to obtain exact linearity of the system. The compensation with a single nonlinear lens cannot cope with distributed nonlinearities, nonlinearities due to parasitic crossings, etc. Here, we present a method to compute parameters of nonlinear element (lens) that eliminates both the footprint and resonance strength without achieving full compensation.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Multicationic interactions mitigating lattice strain in sodium layered cathodes

Transition-metal (TM) layered oxides have emerged as the primary cathode choice for sodium-ion batteries (SIBs) due to their high energy density and sustainable chemistry using non-critical elements. However, their anisotropic lattice strain and stress accumulation during (de)sodiation lead to severe structural degradation, yet an intrinsic strain-depressant approach remains elusive. Herein, we propose entropy regulation with zero Li/Co usage to mitigate harmful lattice displacements and enhance the electrochemical performance of sodium layered cathodes. Our findings demonstrate that high entropy design effectively inhibits TMO 6 octahedra distortions upon cycling, as evidenced by hard X-ray absorption spectroscopy, greatly reducing near-surface structural deconstruction and interface side reactions. Furthermore, multicationic interactions driven by configurational entropy thermodynamically mitigate the formation of oxygen defects and strengthen ligand-to-metal coordination. The complementarity inherent in charge compensation within complex systems is unveiled and the restrained lattice parameters deviations without interior volume residuals are successfully achieved. As a result, the multicationic cathode exhibits improved cycling stability and Na + diffusion kinetics in both half and full cells. The cathode chemistries outlined here broaden the prospects for lattice engineering to alleviate bulk fatigue and open up the possibility to develop an economically viable layered oxides with long durability.

Wang, Haoji [Central South University, Changsha (C↗
NASA NTRS1974

Sunspot models with Alfven wave emission

Sunspot models have been computed on the assumption that the missing flux is transported by undissipated Alfven waves. In order to estimate the flux of these waves, we propose an extension of Opik's cellular model of convection to include the effects of a vertical magnetic field on horizontal gas flow. Horizontal motions, not vertical motions, are impeded more or less severely depending on the electrical conductivity, and this reduces the convective flux. These motions, however, shake the field lines; this is assumed to be a source of Alfven waves, compensating for the reduction in the convective flux. The free parameter D/H (ratio of cell diameter to cell depth) is adjusted such that the total sum of radiative, convective, and Alfven wave fluxes remains constant at all depths and equals the undisturbed solar flux entering the spot from below. Our treatment is speculative to some extent, but it leads to a unique spot model for a given field strength.

Mullan, D. J.↗