Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “n-Type Doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Intersubband absorption in Si(1-x)Ge(x/Si superlattices for long wavelength infrared detectors

Researchers calculated the absorption strengths for intersubband transitions in n-type Si(1-x)Ge(x)/Si superlattices. These transitions can be used for the detection of long-wavelength infrared radiation. A significant advantage in Si(1-x)Ge(x)/Si supperlattice detectors is the ability to detect normally incident light; in Ga(1-x)Al(x)As/GaAs superlattices, intersubband absorption is possible only if the incident light contains a polarization component in the growth direction of the superlattice. Researchers present detailed calculation of absorption coefficients, and peak absorption wavelengths for (100), (111) and (110) Si(1-x)Ge(x)/Si superlattices. Peak absorption strengths of about 2000 to 6000 cm(exp -1) were obtained for typical sheet doping concentrations (approx. equals 10(exp 12)cm(exp -2)). Absorption comparable to that in Ga(1-x)Al(x)As/GaAs superlattice detectors, compatibility with existing Si technology, and the ability to detect normally incident light make these devices promising for future applications.

Rajakarunanayake, Yasantha↗
NASA NTRS1988

Improvements in InP solar cells

Indium phosphide solar cells with very thin n-type emitters have been made by both ion implantation and metal-organic chemical vapor deposition. Air mass zero efficiencies as high as 18.8 percent (NASA measurement) have been achieved. The best cells, which were those made by ion implantation, show an open-circuit voltage of 873 mV, short-circuit current of 35.7 mA/sq cm, and fill factor of 0.829. Improvements are anticipated in all three of these parameters. Internal quantum efficiency peaks at over 90 percent in the red end of the spectrum, but drops to 54 percent in the blue end. Other cells have achieved 74 percent in the blue end. A preliminary investigation of InP solar cells on foreign substrates has been carried out. Although problems have been encountered with doping of the InP by the substrate, cells of 7.1 percent efficiency on silicon and cells of 9.4 percent, efficiency on GaAs have been made.

Keavney, Christopher↗
DOE OSTI2026

Bandgap Engineering of Ga 2 O 3 by MOCVD Through Alloying with Indium

Ga 2 O 3 and In 2 O 3 are vital semiconductors with current and future electronic device applications. Here, we study the alloying of In 2 O 3 and Ga 2 O 3 (IGO) and the associated changes in structure, morphology, band gap, and electrical transport properties. Undoped films of IGO were deposited on sapphire substrates with varying indium (In) percentage from zero to 100% by metal-organic chemical vapor deposition (MOCVD). Some films were annealed in H 2 to induce electrical conductivity. The measurements showed the optical band gap decreased by adding In; this was confirmed by density functional (DFT) calculations, which revealed that the nature of the valence band maximum and conduction band minimum strongly relate to the chemistry and that the band gap drops by adding In. The as-grown films were highly resistive except for pure In 2 O 3 , which possesses p-type conductivity, likely arising from In vacancy-related acceptor states. N-type conductivity was induced in all films after H-anneal. DFT calculations revealed that the presence of In decreases the electron effective mass, which is consistent with the electrical transport measurements that showed higher electron mobility for higher In percentage. The work revealed the successful band gap engineering of IGO and the modification of its band structure while maintaining high-quality films by MOCVD.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Evidence for Ga clusters in β-Ga 2 O 3 from Raman spectroscopy and density functional theory

Monoclinic gallium oxide (β-Ga 2 O 3 ) single crystals have a Raman mode at ∼250 cm −1 that is strongly correlated with free-electron density. Prior work attributed this peak to an electronic excitation of a shallow donor impurity band. However, heavily n-type thin films grown by metalorganic chemical vapor deposition or molecular beam epitaxy do not have the peak. In the present work, an alternate model is proposed: the 250 cm −1 Raman peak arises from Ga clusters, defined as two or more Ga atoms that form Ga–Ga bonds. Raman mapping reveals variations in the frequency that are consistent with a distribution of cluster sizes. The intensity of the peak decreases as the temperature is raised, attributed to melting of the Ga clusters. First-principles calculations indicate that the 250 cm −1 mode is due to Ga–Ga bond-stretching vibrations. As the Fermi energy is raised, the formation of Ga–Ga dimers becomes energetically favorable, explaining the correlation between n-type conductivity and the appearance of the Raman peak.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Local p‐ and n‐Type Doping of an Oxide Semiconductor via Electric‐Field‐Driven Defect Migration

Layered oxides exhibit high ionic mobility and chemical flexibility, attracting interest as cathode materials for lithium-ion batteries and the pairing of hydrogen production and carbon capture. Recently, layered oxides emerged as highly tunable semiconductors. For example, by introducing anti-Frenkel defects, the electronic hopping conductance in hexagonal manganites is increased locally by orders of magnitude. Here, local acceptor and donor doping in Er(Mn,Ti)O3 is demonstrated, facilitated by the controlled splitting of anti-Frenkel defects under applied d.c. voltage. By combining density functional theory calculations, scanning probe microscopy, atom probe tomography, and scanning transmission electron microscopy, it is shown that the oxygen defects can readily be moved through the layered crystal structure, leading to nano-sized interstitial-rich (p-type) and vacancy-rich (n-type) regions. The resulting pattern is comparable to dipolar npn-junctions and stable on the timescale of days. These findings reveal the possibility of temporarily functionalizing oxide semiconductors at the nanoscale, giving additional opportunities for the field of oxide electronics and the development of transient electronics in general.

He, Jiali↗
DOE OSTI2025

p-Type BiVO 4 for Solar O 2 Reduction to H 2 O 2

Photoelectrochemical cells (PECs) can directly utilize solar energy to drive chemical reactions to produce fuels and chemicals. Oxide-based photoelectrodes in general exhibit enhanced stability against photocorrosion, which is a critical advantage for building a sustainable PEC. However, most oxide-based semiconductors are n-type, and p-type oxides that can be used as photocathodes are limited. In this study, we report the synthesis, characterization, and application of p-type BiVO 4 with a monoclinic scheelite (ms) structure. ms-BiVO 4 is inherently n-type, and it has been investigated only as a photoanode to date. In this study, we prepared p-type ms-BiVO 4 (bandgap of 2.4 eV) via atomic doping of Ca 2+ at the Bi 3+ site under an O 2 -rich environment and examined its performance as a photocathode. We then demonstrated that the Ca-doped ms-BiVO 4 photocathode can be used for solar O 2 reduction to H 2 O 2 when coupled with appropriate catalysts. Our computational investigation using hybrid density functional theory revealed that holes are stable as polarons in ms-BiVO 4 and have a low self-trapping energy, that may lead to free carriers in the valence band at finite temperature. Our calculations also show that Ca is an effective shallow acceptor dopant with low formation energy and thermal ionization energy leading to p-type conductivity. In conclusion, our joint experimental and computational results provide critical insights into the design of p-type ms-BiVO 4 , enabling its use as a polaronic oxide photocathode.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Point defects and doping in wurtzite LaN

Wurtzite LaN (wz-LaN) is a semiconducting nitride that has piezoelectric and ferroelectric properties, making it promising for applications in electronics, either as a binary compound or in alloys such as LaAlN. The prospects for wz-LaN in devices are influenced by the properties of point defects and impurities; here, we use first-principles density functional theory with a hybrid functional to calculate their formation energies, as well as their atomic and electronic structures. Among native point defects, we find that nitrogen-related defects, both vacancies ($V^+_N$) and interstitials ($N^-_i$), are energetically most favorable under most relevant chemical potentials and positions of the Fermi level; $V^0_N$ may additionally be observed under N-poor conditions, and $N^0_i$ may be prominent under N-rich conditions. We also investigate the incorporation of oxygen and hydrogen, which will likely be present as unintentional impurities. We find that the $O^+_N$ substitutional species readily forms, but oxygen will not lead to n-type conductivity due to formation of DX centers and compensation by interstitial defects. Similarly, substitutional HN and interstitial H i can compensate both p- and n-type dopants. Our results provide detailed, microscopic guidance for the development of electronic devices based on wz-LaN.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Impact of 12-nm FinFET Technology Variations on TID Effects: A Comparative Study of GF 12LP and 12LP+ at the Transistor Level

Here, this article presents a comparative analysis of total ionizing dose (TID) response in GlobalFoundries’ (GF) 12 low-power (LP) and 12LP+12-nm bulk fin field effect transistor (FinFET) technologies using 10-keV X-rays. Our findings show that 12LP+ n-type transistors demonstrate higher sensitivity to TID degradation of the off-state leakage drain current compared to 12LP. Data indicate that for both 12LP and 12LP+, transistors with higher threshold voltages (VTs) exhibit lower off-state drain-source leakage postirradiation compared to transistors with lower VTs. Data consistently show that transistors with fewer fins per transistor show superior TID tolerance, in both 12LP and 12LP+ technologies. Lower VT transistors in both technologies display similar preirradiation leakage currents. On the other hand, higher VT transistors in 12LP+ show lower preirradiation leakage currents than those in 12LP, highlighting that the front-end-of-line of 12LP+ technology has been modified compared to 12LP. p-type devices in 12LP+ presented negligible degradation. Larger TID sensitivity in 12LP+ might be attributed to the implementation of dual-metal gate work functions, reduced halo doping, deeper source/drain (S/D) doping profiles, and/or 12LP+ having narrower fins compared to 12LP.

Dual-metal gate work functions↗
DOE OSTI2024

Investigation of Contact Properties and Device Performance for Bifacial Double-Side Textured Silicon Solar Cells With Polysilicon Based Passivating Contacts

We investigate the impact of the surface morphology on the contact properties of phosphorus doped poly-Si layers. If the poly-Si layer on a textured surface remains intact after high-temperature metallization using a fire-through (FT) silver (Ag) paste, the J0,metal is not expected to increase significantly while the specific contact resistivity can improve with a textured surface. The contact properties of the FT Ag contacts to n+ poly-Si deposited on both textured and planar surfaces are investigated by measuring and evaluating ρc and J0,metal. The reasons for differences in contact resistance and recombination are further investigated with SEM imaging. Solar cells with n-type polysilicon based passivating contacts on the rear side are fabricated and characterized. The scientific approach used, and the insights presented in this work, help to understand the mechanisms and behavior of screen-printed and fired-through contacts to polysilicon layers deposited onto textured silicon surfaces.

Padhamnath, Pradeep (ORCID:0000000202510624)↗
NASA NTRS1979

Titanium in silicon as a deep level impurity

Titanium inserted in silicon by diffusion or during Czochralski ingot growth is electrically active to a concentration level of about 4 x 10 to the 14th per cu cm. It is reported that Hall measurements after diffusion show conversion of lightly doped p-type Si to n-type due to a Ti donor level at E sub c -0.22 eV. In addition, in DLTS measurements of n(+)p structures this level shows as an electron (minority carrier) trap at E sub c -0.26 eV with an electron capture cross section of about 3 x 10 to the -15th per sq cm at 300 K. Finally, a Ti electrically active concentration of about 1.35 x 10 to the 13th per cu cm in p type Si results in a minority carrier (electron) lifetime of 50 nsec at 300 K.

Chen, J.-W.↗
NASA NTRS1981

Ohmic contacts to GaAs for high-temperature device applications

Ohmic contacts to n-type GaAs were developed for high temperature device applications up to 300 C. Refractory metallizations were used with epitaxial Ge layers to form the contacts: TiW/Ge/GaAs, Ta/Ge/GaAs, Mo/Ge/GaAs, and Ni/Ge/GaAs. Contacts with high dose Si or Se ion implantation of the Ge/GaAs interface were also investigated. The contacts were fabricated on epitaxial GaAs layer grown on N+ or semi-insulating GaAs substrates. Ohmic contact was formed by both thermal annealing (at temperatures up to 700 C) and laser annealing (pulsed Ruby). Examination of the Ge/GaAs interface revealed Ge migration into GaAs to form an N+ doping layer. The specific contact resistances of specimens annealed by both methods are given.

Anderson, W. T., Jr.↗
NASA NTRS1984

Flat-plate solar array project process development area, process research of non-CZ silicon material

The program is designed to investigate the fabrication of solar cells on N-type base material by a simultaneous diffusion of N-type and P-type dopants to form an P(+)NN(+) structure. The results of simultaneous diffusion experiments are being compared to cells fabricated using sequential diffusion of dopants into N-base material in the same resistivity range. The process used for the fabrication of the simultaneously diffused P(+)NN(+) cells follows the standard Westinghouse baseline sequence for P-base material except that the two diffusion processes (boron and phosphorus) are replaced by a single diffusion step. All experiments are carried out on N-type dendritic web grown in the Westinghouse pre-pilot facility. The resistivities vary from 0.5 (UC OMEGA)cm to 5 (UC OMEGA)cm. The dopant sources used for both the simultaneous and sequential diffusion experiments are commercial metallorganic solutions with phosphorus or boron components. After these liquids are applied to the web surface, they are baked to form a hard glass which acts as a diffusion source at elevated temperatures. In experiments performed thus far, cells produced in sequential diffusion tests have properties essentially equal to the baseline N(+)PP(+) cells. However, the simultaneous diffusions have produced cells with much lower IV characteristics mainly due to cross-doping of the sources at the diffusion temperature. This cross-doping is due to the high vapor pressure phosphorus (applied as a metallorganic to the back surface) diffusion through the SiO2 mask and then acting as a diffusant source for the front surface.

Campbell, R. B.↗
NASA NTRS1984

Fermi energy control of vacancy coalescence and dislocation density in melt-grown GaAs

A striking effect of the Fermi energy on the dislocation density in melt-grown GaAs has been discovered. Thus, a shift of the Fermi energy from 0.1 eV above to 0.2 eV below its intrinsic value (at high temperature, i.e., near 1100 K) increases the dislocation density by as much as five orders of magnitude. The Fermi energy shift was brought about by n-type and p-type doping at a level of about 10 to the 17th per cu cm (under conditions of optimum partial pressure of As, i.e., under optimum melt stoichiometry). This effect must be associated with the fact that the Fermi energy controls the charge state of vacancies (i.e., the occupancy of the associated electronic states) which in turn must control their tendency to coalesce and thus the dislocation density. It appears most likely that gallium vacancies are the critical species.

Lagowski, J.↗
NASA NTRS1985

Flat-plate solar array project process development area process research of non-CZ silicon material

Three sets of samples were laser processed and then cell processed. The laser processing was carried out on P-type and N-type web at laser power levels from 0.5 joule/sq cm to 2.5 joule/sq cm. Six different liquid dopants were tested (3 phosphorus dopants, 2 boron dopants, 1 aluminum dopant). The laser processed web strips were fabricated into solar cells immediately after laser processing and after various annealing cycles. Spreading resistance measurements made on a number of these samples indicate that the N(+)P (phosphorus doped) junction is approx. 0.2 micrometers deep and suitable for solar cells. However, the P(+)N (or P(+)P) junction is very shallow ( 0.1 micrometers) with a low surface concentration and resulting high resistance. Due to this effect, the fabricated cells are of low efficiency. The maximum efficiency attained was 9.6% on P-type web after a 700 C anneal. The main reason for the low efficiency was a high series resistance in the cell due to a high resistance back contact.

Source record↗
NASA NTRS1991

Tunnel junctions for InP-on-Si solar cells

Growing, by metalorganic chemical vapor deposition, a tunnel junction is described, which makes possible and ohmic back contact in an n-on-p InP solar cell on a silicon substrate. The junction between heavily doped layers of p-type InGaAs and n-type InP shows resistance low enough not to affect the performance of these cells. InP solar cells made on n-type Si substrates with this structure were measured with an efficiency of 9.9 percent. Controls using p-type GaAs substrates showed no significant difference in cell performance, indicating that the resistance associated with the tunnel junction is less than about 0.1 ohm/sq cm.

Keavney, C.↗
NASA NTRS1995

Site-Competition Epitaxy for N-Type and P-Type Dopant Control in CVD Sic Epilayers

The use of site-competition epitaxy, which is based on intentional variation of the Si/C ratio during epitaxy, has now been reproduced in numerous national and international laboratories. However, previous reports have only considered dopant incorporation control for epitaxy on the Si-face 6H-SiC(OOO1) substrates. Presented in this paper is the extension of this technique for control of phosphorous incorporation and also a comparison of controlled doping on C-face 6H-SiC(OOO1) versus Si-face 6H-SiC(OOO1) substrates for aluminum, boron, nitrogen, and phosphorous.

Larkin, D. J.↗