SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Research projects concerned with developing a theory of fracture of materials are discussed. The effects of the geometry of the structure and the loads acting on the structure as they influence the failure process are analyzed. The effects of the viscoelastic deformation characteristics of the bulk elastomer on failure behavior are examined. Additional material parameters which control the fracture process are identified.
Interlaminar fracture mechanics has proven useful for characterizing the onset of delaminations in composites and has been used successfully primarily to investigate onset in fracture toughness specimens and laboratory size coupon type specimens. Future acceptance of the methodology by industry and certification authorities, however, requires the successful demonstration of the methodology on the structural level. For this purpose, a panel was selected that is reinforced with stiffeners. Shear loading causes the panel to buckle, and the resulting out-of-plane deformations initiate skin/stiffener separation at the location of an embedded defect. A small section of the stiffener foot, web and noodle as well as the panel skin in the vicinity of the delamination front were modeled with a local 3D solid model. Across the width of the stiffener foot, the mixedmode strain energy release rates were calculated using the virtual crack closure technique. A failure index was calculated by correlating the results with a mixed-mode failure criterion of the graphite/epoxy material. Computed failure indices were compared to corresponding results where the entire web was modeled with shell elements and only a small section of the stiffener foot and panel were modeled locally with solid elements. Including the stiffener web in the local 3D solid model increased the computed failure index. Further including the noodle and transition radius in the local 3D solid model changed the local distribution across the width. The magnitude of the failure index decreased with increasing transition radius and noodle area. For the transition radii modeled, the material properties used for the noodle area had a negligible effect on the results. The results of this study are intended to be used as a guide for conducting finite element and fracture mechanics analyses of delamination and debonding in complex structures such as integrally stiffened panels.
It is well known that failure of a material is a locally driven event. In the case of ceramic matrix composites (CMCs), significant variations in the microstructure of the composite exist and their significance on both deformation and life response need to be assessed. Examples of these variations include changes in the fiber tow shape, tow shifting/nesting and voids within and between tows. In the present work, the effects of many of these architectural parameters and material scatter of woven ceramic composite properties at the macroscale (woven RUC) will be studied to assess their sensitivity. The recently developed Multiscale Generalized Method of Cells methodology is used to determine the overall deformation response, proportional elastic limit (first matrix cracking), and failure under tensile loading conditions. The macroscale responses investigated illustrate the effect of architectural and material parameters on a single RUC representing a five harness satin weave fabric. Results shows that the most critical architectural parameter is weave void shape and content with other parameters being less in severity. Variation of the matrix material properties was also studied to illustrate the influence of the material variability on the overall features of the composite stress-strain response.
Erosion resistance and failure mechanisms of nozzle materials in small solid-propellant rocket engine
Dynamic simulation of the lunar outpost habitat life support was undertaken to investigate the impact of life support failures and to investigate responses. Some preparatory static analysis for the Lunar Outpost life support model, an earlier version of the model, and an investigation into the impact of Extravehicular Activity (EVA) were reported previously. (Jones, 2008-01-2184, 2008-01-2017) The earlier model was modified to include possible resupply delays, power failures, recycling system failures, and atmosphere and other material storage failures. Most failures impact the lunar outpost water balance and can be mitigated by reducing water usage. Food solids, nitrogen can be obtained only by resupply from Earth. The most time urgent failure is a lass of carbon dioxide removal capability. Life support failures might be survivable if effective operational solutions are provided in the system design.
Lunar dust known as regolith is a huge challenge for lunar exploration missions. Formed over millennia by a complex process involving impacts of meteoroids and micrometeoroids on the lunar surface, lunar dust is porous, highly abrasive with sharp jagged edges, chemically reactive, electrostatically charged and sometimes magnetic. The chemical composition and thickness of the dust layer also varies in different regions of the lunar surface. From samples obtained by previous lunar missions, the average particle size is below 100 microns. This dust has the tendency to strongly adhere to any exposed surfaces, and often degrades the material functionality to eventually cause failure. Any material on the lunar surface is also subject to harsh temperature cycles ranging from -178 ̊C to + 123 ̊C and extreme ultraviolet radiation. While on the lunar surface, different classes of materials would be required for different applications. Advanced materials have been and will be used throughout the lunar lander, habitat, and mission equipment. Examples include: polymeric materials for astronaut protective clothing; metals and ceramics for the lunar lander legs and habitats, and excavating equipment; and semiconductors for solar panels and on-board electronics. In all these applications, the surfaces of the materials are expected or understood to be exposed to the extreme lunar environment condition that includes the regolith dust. During the Apollo missions, the dust clung to and abraded the astronaut’s suits, degraded seals, optics, clogged sensors and reduced performance of thermal radiators. The lunar dust adheres to the surface by various mechanisms, which include electrostatic and Coulombic interactions, Van-der-Waals forces, magnetic forces, mechanical interlocking, chemical bonding and donor-acceptor interactions. There are three primary strategies for developing technologies to minimize the lunar dust adhesion: active, passive and a combination of active and passive. In the active approach, an external energy is needed to prevent or remove particles from collecting on the surface. Mechanically powered brushes and electrodynamic dust screens are two examples. In the passive approach, no external power is needed, and the material surface properties are able to mitigate dust adhesion. A well-known example of this strategy is the low work function coatings for non-stick surfaces. In most cases a combination of active and passive methods might be needed to optimally manage the lunar regolith. The passive method is significantly more attractive as it does not require any external power or an additional control subsystem. These approaches optimize the mission payload and reduce risk. Surface modification to minimize the dust adhesion is thus very important to lunar missions. Here, naturally evolved surface structures might provide guidance for solutions. There are several factors that have to be considered for minimizing particle adhesion to a surface. These include the substrate material properties, surface topography, chemistry, and the characteristics of the adhering particles. When engineering a surface, the substrate material chosen would be dependent on the needs of the application. Tailoring the surface microstructure or chemistry opens up more possibilities for its optimal utilization
One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the FAA William J. Hughes Technical Center. Unique features of this set of data are that all material property data and impact test data are obtained using identical material, the test methods and procedures are extensively documented and all of the raw data is available. Four parallel efforts are currently underway: Measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles conducted by The Ohio State University; development of improved numerical modeling techniques for deformation and failure conducted by The George Washington University; impact testing of flat panels and substructures conducted by NASA Glenn Research Center. This report describes impact testing which has been done on aluminum (Al) 2024 and titanium (Ti) 6Al-4vanadium (V) sheet and plate samples of different thicknesses and with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.
One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain-rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition, there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data, and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration (FAA) William J. Hughes Technical Center. Unique features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all of the raw data is available. Four parallel efforts are currently underway. The Ohio State University conducts both measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles. The George Mason University conducts the development of improved numerical modeling techniques for deformation and failure. Glenn conducts the impact testing of flat panels and substructures. This report describes impact testing performed on Inconel 718 sheet and plate samples of different thicknesses with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.
The reliability of brittle materials under a generalized state of stress is analyzed using the Batdorf model. The model is modified to include the reduction in shear due to the effect of the compressive stress on the microscopic crack faces. The combined effect of both surface and volume flaws is included. Due to the nature of fracture of brittle materials under compressive loading, the component is modeled as a series system in order to establish bounds on the probability of failure. A computer program was written to determine the probability of failure employing data from a finite element analysis. The analysis showed that for tensile loading a single crack will be the cause of total failure but under compressive loading a series of microscopic cracks must join together to form a dominant crack.
Balloons fabricated of thin polyethylene materials have provided relatively inexpensive and reliable scientific research platforms for approximately three decades. Reliability of the modern day balloon, as launched by the U.S.A. National Scientific Balloon Facility (NSBF), has been approximately 85 percent. Recent balloon failures, coupled with an increased ocurrence of catastrophic failures, created grave concern over the integrity of the present balloon inventory of the U.S.A. National Aeronautics and Space Administration (NASA). An investigative team was established by NASA to review the circumstances surrounding the catastrophic balloon failures, determine the cause and to make recommendations to correct the problem and to prevent its reoccurrence. The most probable cause of failure as determined by the investigation was the polyethylene balloon film, although the film had passsed the established standard quality control measures of the film manufacturer. The approach, findings, and conclusions of the investigation are presented along with planned procedures to assure future quality balloon film for NASA balloons.
A material model which incorporates several key capabilities which have been identified by the aerospace community as lacking in state-of-the art composite impact models is under development. In particular, a next generation composite impact material model, jointly developed by the FAA and NASA, is being implemented into the commercial transient dynamic finite element code LS-DYNA. The material model, which incorporates plasticity, damage, and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters (such as modulus and strength). The plasticity portion of the orthotropic, three-dimensional, macroscopic composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function with a non-associative flow rule. For the damage model, a strain equivalent formulation is utilized to allow for the uncoupling of the deformation and damage analyses. In the damage model, a semi-coupled approach is employed where the overall damage in a particular coordinate direction is assumed to be a multiplicative combination of the damage in that direction resulting from the applied loads in the various coordinate directions. Due to the fact that the plasticity and damage models are uncoupled, test procedures and methods to both characterize the damage model and to covert the material stress-strain curves from the true (damaged) stress space to the effective (undamaged) stress space have been developed. A methodology has been developed to input the experimentally determined composite failure surface in a tabulated manner. An analytical approach is then utilized to track how close the current stress state is to the failure surface.
A brief description is given of the modifications implemented in the PAFAC finite element program for the simulation of progressive failure in fibrous composite materials and structures. Details of the memory allocation, input data, and the new subroutines are given. Also, built-in failure criteria for homogeneous and fibrous composite materials are described.
A primary focus of the Entry Systems and Technology Division at NASA Ames is design, development, qualification and certification of Thermal Protection Systems for current NASA missions. Another primary focus is the development of new thermal protection systems for upcoming missions that address shortfalls in the existing suite of TPS. Examples of such shortfalls include performance at higher capability and reduction in mass. NASA is also investing in TPS sustainability ensuring the long term availability of TPS solutions for future missions. The specific TPS selection, for a given mission , depends on a number of parameters including the missions risk posture. For all missions the goal for TPS is efficient and reliable performance and to achieve these goals an understanding of the materials (composition and architecture) is required for proper design and use of the chosen TPS. Analytic tools are used to inform on a material (systems) response to a given environment and the response itself depends on the materials properties which are driven by its composition and architecture. This presentation will review the different generic ablative TPS architectures and anticipated corresponding failure modes.
Historical data collection on nuclear fuel cladding materials has focused on generating a statistically significant amount of data to assess the material and its failure behavior. Furthermore, data generated to support material model and failure criteria development were previously posttest evaluations, so a large number of tests was required to gain new understanding. A way to expedite this process is to develop techniques capable of generating large, high-fidelity data sets from a single test with lower uncertainty or quantified uncertainty. One such example of this approach is Oak Ridge National Laboratory’s use of modified burst tests (MBTs) to analyze the mechanical behavior and failure conditions of cladding during a simulated reactivity-initiated accident (RIA). Each test incorporates digital image correlation (DIC) analysis techniques that are used to assess the accumulated strain in situ, as well as eventual cladding failure. This work has been fruitful in defining strain-to-failure conditions for materials like silicon carbide (SiC) fiber–reinforced/SiC matrix composite tubes (SiC/SiC), iron-chromium-aluminum (FeCrAl) alloy tubes, and chromium-coated Zircaloy-4 tubes. However, there are numerous DIC software available, including open-source and proprietary software. The different DIC software use various algorithms to process images and calculate displacement values. Using these different software and algorithms can lead to varying results, and perhaps larger-than-expected uncertainties. In the present study, previously published MBT data encompassing a variety of test conditions were reanalyzed with two different DIC software to assess the variance in the calculated strain results. The data consisted of SiC/SiC, FeCrAl, and chromium-coated Zircaloy-4 tubes. Plots of the calculated strains during the transient revealed good agreement between the two DIC software. The average root-mean-square errors between the two software was 0.20% strain, which is slightly larger than a previously reported error value for these tests. In conclusion, this variance in results is low enough that this analysis method can be used for code validation.
A phenomenological description of microfailure under monotonic and cyclic loading is presented, emphasizing the significance of material inhomogeneity for the analysis. Failure in unnotched unidirectional laminates is reviewed for the cases of tension, compression, shear, transverse normal, and combined loads. The failure of notched composite laminates is then studied, with particular attention paid to the effect of material heterogeneity on load concentration factors in circular holes in such laminates, and a 'materials engineering' shear-lay type model is presented. The fatigue of notched composites is discussed with the application of 'mechanistic wearout' model for determining crack propagation as a function of the number of fatigue cycles.-
In April 2004 a Space Shuttle Orbiter Reaction Control System (RCS) thruster was found to be cracked while undergoing a nozzle (niobium/C103 alloy) retrofit. As a failure resulting from an in-flight RCS thruster burn-through (initiated from a crack) could be catastrophic, an official Space Shuttle Program flight constraint was issued until flight safety could be adequately demonstrated. This paper describes the laboratory test program which was undertaken to reproduce the cracking in order to fully understand and bound the driving environments. The associated rationale developed to justify continued safe flight of the Orbiter RCS system is also described. The laboratory testing successfully reproduced the niobium cracking, and established specific bounding conditions necessary to cause cracking in the C103 thruster injectors. Each of the following conditions is necessary in combination together: 1) a mechanically disturbed / cold-worked free surface, 2) an externally applied sustained tensile stress near yield strength, 3) presence of fluorine-containing fluids on exposed tensile / cold-worked free surfaces, and 4) sustained exposure to temperatures greater than 400 F. As a result of this work, it was concluded that fluorine-containing materials (e.g. HF acid, Krytox , Brayco etc.) should be carefully controlled or altogether eliminated during processing of niobium and its alloys.
Fracture mechanisms for viscoelastic materials
Fracture mechanics in linearly viscoelastic materials