Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “load forecasting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Recommendations for a wind profiling network to support Space Shuttle launches

The feasibility is examined of a network of clear air radar wind profilers to forecast wind conditions before Space Shuttle launches during winter. Currently, winds are measured only in the vicinity of the shuttle launch site and wind loads on the launch vehicle are estimated using these measurements. Wind conditions upstream of the Cape are not monitored. Since large changes in the wind shear profile can be associated with weather systems moving over the Cape, it may be possible to improve wind forecasts over the launch site if wind measurements are made upstream. A radar wind profiling system is in use at the Space Shuttle launch site. This system can monitor the wind profile continuously. The existing profiler could be combined with a number of radars located upstream of the launch site. Thus, continuous wind measurements would be available upstream and at the Cape. NASA-Marshall representatives have set the requirements for radar wind profiling network. The minimum vertical resolution of the network must be set so that the wind shears over the depths greater than or = 1 km will be detected. The network should allow scientists and engineers to predict the wind profile over the Cape 6 hours before a Space Shuttle launch.

Zamora, R. J.↗
DOE OSTI2026

Machine learning-enhanced MPC for demand flexibility in small commercial buildings: An experimental study

Small- and medium-sized commercial buildings (SMCBs) represent the majority of U.S. commercial building stock and a significant share of peak electricity demand, yet they often lack centralized building automation systems, representing a significant untapped resource for urban energy management. This infrastructure gap makes advanced control implementation challenging, limiting the potential for widespread demand flexibility. Model Predictive Control (MPC) has shown strong potential for load shifting, peak demand reduction, and cost savings, but its effectiveness is hindered by unmeasured disturbances such as internal heat gains. This paper presents a Hybrid MPC framework that integrates a physics-based gray-box building thermal model, identified using a lumped disturbance (LD) approach, with a machine learning (ML) model for forecasting unmeasured disturbances. The hybrid approach is designed for buildings with multiple individually controlled heat pump and thermostat pairs, common in SMCBs, and aims to optimize coordinated scheduling of multiple heat pumps under dynamic electricity pricing while respecting comfort constraints. The methodology is validated through both simulations of case study buildings and experimental studies at a highly-instrumented test facility. Simulation results show that the Hybrid MPC achieves substantial load shifting and peak demand reduction, approaching the performance of an ideal MPC with perfect disturbance knowledge, and outperforming a conventional MPC without disturbance forecasting. In experiments, the Hybrid MPC reduced daily HVAC energy costs by 8.7%, peak-price time load (load shifting) by 41.7%, and peak demand by 29.2% compared to baseline control, demonstrating comparable benefits to the 11.6% cost savings, 42.9% load shifting, and 23.2% peak reduction of the ideal MPC. These results demonstrate that the proposed hybrid modeling approach can significantly improve MPC performance in real-world SMCB applications without requiring additional disturbance measurements.

Demand Flexibility↗
NASA NTRS1998

A Table-Driven Control Method to Meet Continuous, Near-Real-Time Observation Requirements for the Solar X-Ray Imager

The design of the Solar X-Ray Imager (SXI) for the Geostationary Operational Environmental Satellite (GOES) presents an unusual scenario for controlling the observing sequences. The SXI is an operational instrument, designed not primarily for scientific research, but for providing "operational" data used by the National Oceanic and Atmospheric Administration (NOAA) to forecast the near-term space weather. To this end, a sequence of images selected to cover the full dynamic range of the sun will be executed routinely. As the dynamics of the sun have differing temporal cadences, the frequency of various images will differ. These images must be routinely received at the forecast center in near real-time, 24-hours a day, with a minimum of interruptions. While these requirements clearly lead to a 'routine patrol' of images, the parameters for each do not form a static set. The dynamics of the sun will change with the I 1-year solar cycle. The performance of the imaging will vary with on-orbit conditions and time. And while the SXI is not intended as a research instrument, forecasting techniques may change with time, which in turn will further alter the imaging sequences. An additional complication is the highly restricted commanding window, and a very slow commanding rate. To fulfill these requirements, the SXI was designed to utilize a table-driven approach. Sequences are defined using structured loops, with nested repetitions and delays. These sequences reference combinations of imaging parameters which in turn reference tables of parameters than can be loaded by ground commands. Multiple sequences can be built and stored in preparation for execution when determined appropriate by the NOAA forecasters. The result is an approach that can be used to provide a flexible, yet autonomous SXI capable of meeting both arbitrary forecasting requirements, and operating within the commanding constraints.

Wallace, Shawn↗
NASA NTRS2022

A Multimodel Investigation of Asian Summer Monsoon UTLS Transport Over the Western Pacific

The Asian summer monsoon (ASM) as a chemical transport system is investigated using a suite of models in preparation for an airborne field campaign over the Western Pacific. Results show that the dynamical process of anticyclone eddy shedding in the upper troposphere rapidly transports convectively uplifted Asian boundary layer air masses to the upper troposphere and lower stratosphere over the Western Pacific. The models show that the transported air masses contain significantly enhanced aerosol loading and a complex chemical mixture of trace gases that are relevant to ozone chemistry. The chemical forecast models consistently predict the occurrence of the shedding events, but the predicted concentrations of transported trace gases and aerosols often differ between models. The airborne measurements to be obtained in the field campaign are expected to help reduce the model uncertainties. Furthermore, the large-scale seasonal chemical structure of the monsoon system is obtained from modeled carbon monoxide, a tracer of the convective transport of pollutants, which provides a new perspective of the ASM circulation, complementing the dynamical characterization of the monsoon.

Laura L. Pan↗
NASA NTRS1981

Technology development of the Space Transportation System mission and terrestrial applications of satellite technology

The Space Transportation System (STS) is discussed, including the launch processing system, the thermal protection subsystem, meteorological research, sound supression water system, rotating service structure, improved hypergol or removal systems, fiber optics research, precision positioning, remote controlled solid rocket booster nozzle plugs, ground operations for Centaur orbital transfer vehicle, parachute drying, STS hazardous waste disposal and recycle, toxic waste technology and control concepts, fast analytical densitometry study, shuttle inventory management system, operational intercommunications system improvement, and protective garment ensemble. Terrestrial applications are also covered, including LANDSAT applications to water resources, satellite freeze forecast system, application of ground penetrating radar to soil survey, turtle tracking, evaluating computer drawn ground cover maps, sparkless load pulsar, and coupling a microcomputer and computing integrator with a gas chromatograph.

Source record↗
DOE OSTI2024

A Test of Functional Balance Theory for Wetland Biomass Allocation in a Global Change Experiment

Abstract Forecasts of root growth and carbon sequestration under global change are compromised by uncertainty in how plants will allocate biomass between above and belowground pools. Here, we develop a simple model to assess whether functional balance theory can explain a complex biomass allocation response observed in a brackish marsh under experimental warming and elevated CO 2 . Our model shows how treatment‐driven changes in nitrogen supply and demand can explain divergent observations of root growth (i.e., maximum responses under intermediate warming and elevated CO 2 ). The model also reveals a surprising interaction between warming and eutrophication, where enhanced N loading to coastal marshes may reduce adverse impacts of warming on root growth. Our findings provide a mechanistic basis for incorporating biomass allocation into forecast models of marsh evolution. They also provide a general example of using ecological theory to decompose complex net responses observed in multi‐factor global change experiments into constituent processes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Design considerations for a Digital Twin built to improve nitrification performance at a water resource recovery facility

A Digital Twin built around Activated Sludge Model No. 1 was deployed at a full-scale water resource recovery facility. Its design included a waste rate recommender system based on automatic scenario analyses, where influent loads and waste rates are varied to determine their impact on nitrification. At the same frequency as these scenario analyses, scheduled auto-calibrations allow for nitrifier maximum specific growth rate (μmax-NITO) soft sensing, the only kinetic parameter shown to require adjustment if the objective is aeration tank effluent ammonia forecasting accuracy. By integrating temperature forecasting over the next three sludge ages, this Digital Twin approach creates opportunities for advancing waste rate decisions in anticipation of seasonal temperature changes, optimizing ammonia control authority under varying influent loads, and furnishing valuable insights for future capital projects requiring nitrifier kinetic understanding and modelling.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1997

A Study of the Use of Contact Loading to Simulate Low Velocity Impact

Although numerous studies on the impact response of laminated composites have been conducted, there is as yet no agreement within the composites community on what parameter or parameters are adequate for quantifying the severity of an impact event. One of the more interesting approaches that has been proposed uses the maximum contact force during impact to "quantify" the severity of the impact event, provided that the impact velocity is sufficiently low. A significant advantage of this approach, should it prove to be reliable, is that quasi-static contact loading could be used to simulate low velocity impact. In principle, a single specimen, loaded quasi-statically to successively increasing contact loads could be used to map the entire spectrum of damage as a function of maximum contact force. The present study had as its objective assessing whether or not the maximum contact force during impact is a suitable parameter for characterizing an impact. The response of [+/-60/0(sub 4)/+/-60/0(sub 2)](sub s) laminates fabricated from Fiberite T300/934 graphite epoxy and subjected to quasi-static contact loading and to low velocity impact was studied. Three quasi-static contact load levels - 525 lb., 600 lb., and 675 lb. - were selected. Three impact energy levels - 1.14 ft.-lb., 2.0 ft.-lb., and 2.60 ft.-lb. - were chosen in an effort to produce impact events in which the maximum contact forces during the impact events were 525 lb., 600 lb., and 625 lb., respectively. Damage development was documented using dye-penetrant enhanced x-ray radiography. A digital image processing technique was used to obtain quantitative information about the damage zone. Although it was intended that the impact load levels produce maximum contact forces equal to those used in the quasi-static contact experiments, larger contact forces were developed during impact loading. In spite of this, the damage zones developed in impacted specimens were smaller than the damage zones developed in specimens subjected to the corresponding quasi-static contact loading. The impacted specimens may have a greater tendency to develop fiber fracture, but, at present, a quantitative assessment of fiber fracture is not available. In addressing whether or not contact force is an adequate metric for describing the severity of an impact event, the results of this study suggest that it is not. In cases where the quasi-static load level and the maximum contact force during impact were comparable, the quasi-statically loaded specimens consistently developed larger damage zones. It should be noted, however, that using quasi-static damage data to forecast the behavior of impacted material may give conservative estimates of the residual strength of impacted composites.

Highsmith, Alton L.↗
DOE OSTI2026

Assessing shellfish water exposure to fecal bacteria pollution in Salish Sea: three-dimensional modeling and implications for monitoring

Fecal bacteria (FB) contamination poses significant risks to shellfish safety and management in coastal and estuarine waters. Despite extensive pollution identification and correction efforts, FB contamination in shellfish-growing areas persists in the Salish Sea, highlighting the need to identify overlooked sources and better understand FB transport from riverine and shoreline inputs to shellfish beds. To address this, a high-resolution three-dimensional hydrodynamic model coupled with FB kinetics was developed and applied to a case study site in Salish Sea—Portage Bay—to simulate freshwater plume circulation, flushing dynamics, and bacterial transport. Daily FB loading from the major freshwater inflow—Nooksack River was generated by both linear interpolation and integrating a machine learning approach (XGBoost), trained on historical hydrological and meteorological data. The model successfully reproduced both the magnitude and seasonal variation of FB concentrations in Portage Bay for the year of 2021, demonstrating that simplified FB kinetics with first-order decay due to mortality was effective in this dynamic coastal environment with short flushing time. Model results identified the Nooksack River as the dominant far-field FB source, while scenario simulations showed that near-field coastal stormwater outfalls elevated local FB levels following rainfall, particularly under low-flow conditions. The XGBoost prediction provided comparable or superior accuracy to linear interpolation, particularly during periods of missing observational data, by capturing short-term variability and event-driven loading more effectively. Integrating data-driven riverine FB inputs with mechanistic coastal numerical modeling provides a robust framework for operational forecasting of shellfish bed exposure risk and supports adaptive monitoring and management of shellfish growing areas in the Salish Sea and similar coastal systems.

Salish Sea↗
NASA NTRS1975

Survey of projected growth and problems facing air transportation, 1975 - 1985

Results are presented of a survey conducted to determine the current opinion of people working in air transportation demand forecasting on the future of air transportation over the next ten years. In particular, the survey included questions on future demand growth, load factor, fuel prices, introduction date for the next new aircraft, the priorities of problems facing air transportation, and the probability of a substantial change in air transportation regulation. The survey participants included: airlines, manufacturers, universities, government agencies, and other organizations (financial institutions, private research companies, etc.). The results are shown for the average responses within the organization represented as well as the overall averages.

Williams, L. J.↗
NASA NTRSDate not supplied

Emissions Characterization and Smoke Transport of A Prescribed Fire

Under the background of climate change, vast regions of the world will face a hotter and probably drier future that favors ignition and spread of wildfires. This poses additional challenges to the communities who are fighting the ever-larger wildfires. Fire and smoke models are valuable tools to fire managers and decision-makers to mitigate the impact of fires. Existing fire modeling systems bear large uncertainties due to the difficulty in collecting data to characterize fire behavior and smoke transport. More observations are urgently needed for improvement of fire modeling and reduction in model uncertainty. The coordinated prescribed burn experiment, such as the Fire and Smoke Model and Measurement Evaluation Experiment (FSMMEE), will allow the concurrent collection of critical measurements of fuel, fire behavior, smoke, and meteorology to better understand and model fires. In this preliminary investigation, we employed the data from the prescribed burn experiment at Langdon Mountain, Utah, in November 2019, to reconstruct the fire emissions and characterize the smoke transport. The NASA Unified Weather Research and Forecasting Model (NU-WRF) was utilized to assist in identifying the potential pre-fire remote sensing capabilities, such as fuel load, moisture, and fire radiative power, which are helpful to model development and advancement. Along the way, two sets of NU-WRF experiments would be done by applying either a default fire emissions inventory (i.e., NASA’s Quick Fire Emissions Dataset, QFED) or reconstructed fire emissions using the data collected from the prescribed fire. The results would help answer the questions such as “How do reconstructed emissions compare to QFED emissions and their impact on plume transport”.

NU-WRF↗
NASA NTRS1976

The promise of air cargo: System aspects and vehicle design

The current operation of the air cargo system is reviewed. An assessment of the future of air cargo is provided by: (1) analyzing statistics and trends, (2) by noting system problems and inefficiencies, (3) by analyzing characteristics of 'air eligible' commodities, and (4) by showing the promise of new technology for future cargo aircraft with significant improvements in costs and efficiency. The following topics are discussed: (1) air cargo demand forecasts; (2) economics of air cargo transport; (3) the integrated air cargo system; (4) evolution of airfreighter design; and (5) the span distributed load concept.

Whitehead, A. H., Jr.↗
NASA NTRS1980

Application of Advanced Technologies to Small, Short-haul Air Transports

A study was conducted of the application of advanced technologies to small, short-haul transport aircraft. A three abreast, 30 passenger design for flights of approximately 100 nautical miles was evaluated. Higher wing loading, active flight control, and a gust alleviation system results in improved ride quality. Substantial savings in fuel and direct operating cost are forecast. An aircraft of this configuration also has significant benefits in forms of reliability and operability which should enable it to sell a total of 450 units through 1990, of which 80% are for airline use.

Adcock, C.↗
NASA NTRS1985

A review of fracture mechanics life technology

Current lifetime prediction technology for structural components subjected to cyclic loads was reviewed. The central objectives of the project were to report the current state of and recommend future development of fracture mechanics-based analytical tools for modeling and forecasting subcritical fatigue crack growth in structures. Of special interest to NASA was the ability to apply these tools to practical engineering problems and the developmental steps necessary to bring vital technologies to this stage. A survey of published literature and numerous discussions with experts in the field of fracture mechanics life technology were conducted. One of the key points made is that fracture mechanics analyses of crack growth often involve consideration of fatigue and fracture under extreme conditions. Therefore, inaccuracies in predicting component lifetime will be dominated by inaccuracies in environment and fatigue crack growth relations, stress intensity factor solutions, and methods used to model given loads and stresses. Suggestions made for reducing these inaccuracies include: development of improved models of subcritical crack growth, research efforts aimed at better characterizing residual and assembly stresses that can be introduced during fabrication, and more widespread and uniform use of the best existing methods.

Thomas, J. M.↗
NASA NTRS2016

C/NOFS Remote Sensing of Ionospheric Reflectance

Alfvn waves play critical roles in the electrodynamic coupling of plasmas at magnetically conjugate regions in near-Earth space. Associated electric (E*) and magnetic (dec B*) field perturbations sampled by sensors on satellites in low-Earth orbits are generally super positions of incident and reflected waves. However, lack of knowledge about ionospheric reflection coefficients (alpha) hinders understanding of generator outputs and load absorption of Alfvn wave energies. Here we demonstrate a new method for estimating using satellite measurements of ambient E* and dec B* then apply it to a case in which the Communication Navigation Outage Forecasting System (CNOFS) satellite flew conjugate to the field of view of a 630.0 nm all-sky imager at El Leoncito, Argentina, while medium-scale traveling ionosphere disturbances were detected in its field of view. In regions of relatively large amplitudes of E* and B*,calculated values ranged between 0.67 and 0.88. This implies that due to impedance mismatches, the generator ionosphere puts out significantly more electromagnetic energy than the load can absorb. Our analysis also uncovered caveats concerning the methods range of applicability in regions of low E* and B*. The method can be validated in future satellite-based auroral studies where energetic particle precipitation fluxes can be used to make independent estimates of alpha.

Burke, W. J.↗
DOE OSTI2025

Forecasting Battery Electrode Performance via Electrochemical Fluorescence Microscopy and Machine-Learning

Predicting lithium-ion battery performance is hindered by microscale electrode heterogeneities invisible to conventional diagnostics. Here, we combine electrochemical fluorescence microscopy (EFM), which maps electronic connectivity by visualizing an electrofluorophore reaction distribution, with a multitask ElasticNet regression to forecast discharge capacity from spatial heterogeneity. Analyzing 196 images from six pilot-scale LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathodes with varying carbon loadings, we extract 62 descriptors that capture morphology and texture. A compact five-feature model predicts capacity across eight discharge rates, achieving a per-target R 2 of up to 0.63 and an overall R 2 of 0.92, with a mean absolute percentage error of less than 2%. This performance rivals impedance-based approaches while avoiding their reliance on postformation data and incomplete electronic network information. Our facile and rapid, image-driven method may enable electrode quality control upstream of costly cell assembly to offer a transformative tool for data-driven battery research and manufacturing.

battery electrodes↗
NASA NTRS1981

Economic evaluation of a solar hot-water-system

Analysis shows economic benefits at six representative sites using actual data from Tempe, Arizona and San Diego, California installations. Model is two-tank cascade water heater with flat-plate collector array for single-family residences. Performances are forecast for Albuquerque, New Mexico; Fort Worth, Texas; Madison, Wisconsin; and Washington, D.C. Costs are compared to net energy savings using variables for each site's environmental conditions, loads, fuel costs, and other economic factors; uncertainty analysis is included.

Source record↗
NASA NTRS1996

Project Galileo at Jupiter

Galileo made a highly successful arrival at Jupiter on December 7, 1995. The Galileo Atmospheric Entry Probe transmitted the first-ever direct measurements of an outer planet to the Orbiter mothership for nearly one hour while decsending to a pressure depth of 23 bar-far beyond the 10 bar mission requirements...This paper will summarize: 1) the Probe mission results, both engineering and scientific, 2) the problems with the Orbiter tape recorder and its recovery, 3) the Orbiter engineering operations including the loading and performance of the new flight software, and 4) early science results from the arrival and first two orbits and Ganymede encounters. Overall, mission status and the forecast for the remainder of the Orbiter's two-year primary mission will also be provided.

Galileo↗