Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Enhanced copper–carbon nanotube hybrid conductors with titanium adhesion layer

Cu–carbon nanotube (CNT) hybrids combine the advantages of the high electrical conductivity of Cu with the low temperature coefficient of resistance for CNTs, but require enhanced interfacing to improve the electrical performance when exposed to elevated temperatures. In this work, Ti and Ni were investigated as adhesion metals by thermally evaporating 10 nm layers onto a CNT conductor. SEM analysis shows Ni deposits as discrete nanoscale crystallites which coalesce after annealing to 400 °C in H 2 /Ar. Ti deposits uniformly along the CNT surface and is stable over such temperatures. A 100 nm deposition of Cu is shown to delaminate from the CNTs after annealing, and the resistance per length (R/L) increases by 40%. The Cu–Ni–CNT exhibits a 125% increase, while the Cu–Ti–CNT achieves a 12% decrease in R/L, for similar annealing conditions. Thus, Ti emerges as an effective adhesion metal, warranting its use in metal–CNT wire technologies for elevated temperature operation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

AlGaN/GaN metal–insulator–semiconductor high electron mobility transistors (MISHEMTs) using plasma deposited BN as gate dielectric

AlGaN/GaN metal–insulator–semiconductor high electron mobility transistors (MISHEMTs) were fabricated on Si substrates with a 10 nm boron nitride (BN) layer as a gate dielectric deposited by electron cyclotron resonance microwave plasma chemical vapor deposition. The material characterization of the BN/GaN interface was investigated by X-ray photoelectric spectroscopy (XPS) and UV photoelectron spectroscopy. The BN bandgap from the B1s XPS energy loss is ~5 eV consistent with sp2 bonding. The MISHEMTs exhibit a low off-state current of 1 × 10 –8 mA/mm, a high on/off current ratio of 10 9 , a threshold voltage of –2.76 V, a maximum transconductance of 32 mS/mm at a gate voltage of –2.1 V and a drain voltage of 1 V, a subthreshold swing of 69.1 mV/dec, and an on-resistance of 12.75 Ω·mm. The interface state density (D it ) is estimated to be less than 8.49 × 10 11 cm –2 eV –1 . Gate leakage current mechanisms were investigated by temperature-dependent current–voltage measurements from 300 K to 500 K. The maximum breakdown electric field is no less than 8.4 MV/cm. Poole–Frenkel emission and Fowler–Nordheim tunneling are indicated as the dominant mechanisms of the gate leakage through the BN gate dielectric at low and high electric fields, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Heterostructured nano-catalysts with efficient metal-oxide interfaces unlock high-performance direct methanol protonic ceramic fuel cells

Direct methanol protonic ceramic fuel cells (PCFCs) are attractive due to their low cost, convenient storage, and high volumetric energy density, as well as their suitability for transportation. However, the poor coking tolerance of conventional nickel-based anodes leads to their susceptibility to severe carbon deposition and significant deactivation after long-term exposure to hydrocarbons. Herein, we report a nano-catalyst of Ce 0.6 Ni 0.2 Cu 0.2 O 2 with a heterogeneous structure that is spontaneously reduced into a Ce 0.6 Ni 0.2-x Cu 0.2-x O 2-δ (CeNCO) oxide framework interfaced with a nano NiCu alloy (denoted as NC/CeNCO) under operating conditions, as confirmed by analyses of X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. A Ni-BaCe 0.7 Y 0.06 Yb 0.06 Zr 0.06 Hf 0.06 Gd 0.06 O 3-δ anode-supported PCFC employing the NC/CeNCO metal-oxide catalyst achieved a peak power density of 1.11 W cm −2 and operational stability of about 100 h at 700 °C when fueled by 35 % CH 3 OH-15 % H 2 O-50 % N 2 . In conclusion, the enhanced performance and coking resistance are attributed to the efficient interfaces of Ni, Cu, and ceria-based oxide in NC/CeNCO for CH 3 OH reforming, as confirmed by analyses of electrochemical performance and Raman spectroscopy with density functional theory calculations, revealing that these interfaces can enhance CH 3 OH activation and promote efficient OH-mediated carbon removal via COH intermediates.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Electrical conductivity of multilayered Cu/Nb composites fabricated by accumulative roll bonding

The electrical conductivity of nanolayered copper/niobium composites fabricated using accumulative roll bonding was investigated as a function of layer thickness. Cu/Nb was used as a model system to evaluate the processing-structure–property relationship stemming from the accumulative roll bonding process. The physical properties were compared against samples of individual average layer heights ranging from 193 to 25 nm. The electrical resistivity was measured over a temperature range of ~3–300 K. Analysis on the role of interfaces on temperature dependence is conducted including the residual resistivity ratio and temperature coefficient of resistivity. It was found that electrical resistivity increases with decreasing layer height.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure Experiments-Enabled MARMOT Simulations of SiC/SiC-based Accident Tolerant Nuclear Fuel System

We have undertaken an experimental-computational project that addresses a few key technology gaps associated with the use of SiC/SiC composites for light water reactor fuel cladding. Two principal endeavors in this project are to assess the irradiation-induced microstructural changes and swelling in SiC/SiC composites, and to characterize and model the porous oxide surface layer (when exposed to steam) along SiC recession that is detrimental to the clad integrity under accident conditions. The project tasks are: (i) ion irradiation and characterization (University of Tennessee, Knoxville), (ii) mechanical tests and analysis (University of South Carolina), (iii) steam exposure tests (Oak Ridge National Laboratory), (iv) electron microscopy and spectroscopic characterization (NC State University), (v) x-ray microscopy and reconstruction (University of South Carolina and NC State University), (vi) phase field modeling and simulations (NC State University and Idaho National Laboratory). The effects of 10 MeV Au ion irradiation at 350°C on the microstructure evolution in SiC/SiC composites are investigated at doses up to 400 displacements per atom (dpa) at the University of Tennessee, Knoxville. Atomic force microscopy and optical profilometry reveal irradiation induced axial and radial shrinkage of the fibers for doses greater than 10 dpa. Based on detailed electron microscopy characterization, the primary cause of the fiber shrinkage is attributed to irradiation-induced loss of carbon packets. Additionally, the multilayer PyC interface is observed to portray high resistance to irradiation damage. The mechanical response and failure mechanisms of un-irradiated samples is also assessed through loading tests and X-ray imaging at the University of South Carolina. Steam exposure tests are performed at the Oak Ridge National Laboratory in a facility that represents a reactor pressure vessel under a loss-of-coolant-accident scenario. The samples that are analyzed methodically in this report are tested for 32/31 hours at 1200°C with a velocity of 0.25 cm/s for the pressures: 0.1 MPa, 0.45 MPa, 0.92 MPa and 1.38 MPa. Scanning/transmission electron microscopy analysis conducted at the NC State University (NCSU) shows that the oxide layer thickness increases with the steam pressure. While the oxide layer is crystalline (α- cristobalite) for the pressures 0.45 MPa, 0.92 MPa and 1.38 MPa, the layer is amorphous at 0.1 MPa. Results from Raman spectroscopy have also confirmed the formation of α-cristobalite phase of SiO₂. The abrupt increase in the integrated Raman intensity ratio between steam pressures 0.1 and 0.45 MPa suggests the onset of accelerated crystallization. Non-destructive three dimensional X-ray microscopy/tomography (XCT) and computational image processing techniques are employed by the University of South Carolina to probe the porous oxidation features on SiC samples at varying pressures. Interestingly, most pores are observed to be located away from the surface as well as the oxide-SiC interface. The average oxide layer thickness assessed from the XCT analysis is seen to be in excellent agreement with the values determined through scanning electron microscopy analysis for the highest pressures where the oxide layer is relatively more uniform. A phase-field model developed by the NC State University and Idaho National Laboratory for simulating oxidation of SiC by steam captures the paralinear kinetics of SiC oxidation with a high degree of fidelity. Results from quasi-one-dimensional and two dimensional simulations show that the pores with oxidizing species lead to a higher volatilization rate. These simulations indicate that the enhanced apparent volatilization rates at higher pressures observed in experiments can be rationalized by the increased volatilization from the pores. The project team has also successfully developed the capability to import images from experiments for realistic evolution of the oxidizing microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

A Hybrid Quantum–Classical Study of Ion Adsorption at the Copper Electrode

Here, we present a set of computational studies that surveys the molecular structure and thermodynamics of simple ions at the electrode–electrolyte interface. A hybrid quantum–classical approach is used to obtain free energy profiles and solvent structure as a function of the ion’s position relative to the electrochemical liquid/solid interface and system potential. Model systems consist of a copper electrode and single halide or alkali metal ion in contact with an implicit solvent and reveal new insights into the interplay of forces that drive or resist ion absorption at the electrode/ electrolyte interface. We also expand on subtleties of absorption site preference and describe the complex relationship between the energetic barrier to absorption and the ion–electrode binding energy as a function of electrode potential.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect of Propagating Dopant Reactivity on Lattice Oxygen Loss in LLZO Solid Electrolyte Contacted with Lithium Metal

Lithium lanthanum zirconium oxide (LLZO) is widely known as the most stable solid electrolyte against lithium metal electrodes. This thermodynamic stability can be lost by the presence of dopants which are required to stabilize the cubic phase of LLZO and can be reduced by lithium metal. However, the role of oxygen in such reactions is taken for granted. In this work, the reduction of Nb-substituted LLZO (Nb-LLZO) is explored by Li metal and shows that interfacial reactions propagate and lead to the decomposition with substantial Nb 5+ reduction deep into the bulk electrolyte. Scanning Transmission Electron Microscopy with Energy Dispersive X-ray Spectroscopy and thermogravimetric analyses show much of the reduction is due to oxygen vacancies formed, leading to increased electronic conductivity mapped with conductive Atomic Force Microscopy. Density functional theory calculations indicate oxygen release is favored by increased excess lithiation of Nb-LLZO. Electrochemical impedance of polycrystalline Nb-LLZO shows the continuous evolution of ionically resistive interphases near the lithium metal interface with Nb-LLZO while single crystals show little reactivity at room temperature and self-limiting reduction at 60°C. This work underlines the role of grain boundaries in propagating destructive solid electrolyte reactions and highlights previously unseen mechanisms involving lattice oxygen in LLZO.

Li metal, solid-state electrolytes↗
DOE OSTI2020

Interfacial toughness: dependence on surface roughness and test temperature

Interfacial toughness quantifies resistance to crack growth along an interface and in this investigation the toughness of an aluminum/epoxy interface was measured as a function of surface roughness and test temperature. The large strain response of the relatively ductile epoxy adhesive used in this study was also characterized. This epoxy adhesive exhibits intrinsic strain-softening after initial compressive yield and then deforms plastically at a roughly constant flow stress until it rapidly hardens at large compressive strains. Here, we find that interface toughness scales as the product of the temperature dependent epoxy yield strength and a length scale that characterizes surface roughness. The proposed scaling is based upon dimensional considerations of a model problem that assumes that the characteristic length scale of both the roughness and the crack-tip yield zone is small relative to the region dominated by the linear elastic asymptotic crack-tip stress field. Furthermore, the model assumes that interfacial failure occurs only after the epoxy begins to harden at large strains. The proposed relationship is validated by our interfacial toughness measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fabrication of high-performance gas-diffusion-electrode based membrane-electrode assemblies

This paper demonstrates the fabrication and processing steps required to produce high performance fuel cell membrane electrode assemblies (MEAs) based on spray-coated gas-diffusion electrodes (GDEs). It is demonstrated that coating the catalyst layer with a thin layer of ionomer and then hot pressing the GDEs to the membrane is required to achieve comparable catalyst activity and air performance to catalyst-coated-membrane MEAs. We show that there is a critical amount of ionomer required to achieve maximized performance. Using electron microscopy, we show that the combination of the ionomer overlayer and hot-pressing bonds the catalyst layer to the membrane, increasing the interfacial contact area and quality of this interface. We also find that the ionomer overlayer smooths the surface of the GDE and provides increased contact area between the GDE and the membrane. Additionally, we demonstrate that much less ionomer is required for high-performance than has been previously reported. Through model fitting of electrochemical impedance spectroscopy, we show that this improvement in the catalyst layer - membrane interface reduces the effective catalyst layer resistance, which reduces Ohmic losses and increases catalyst utilization.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Macroscale superlubricity by a sacrificial carbon nanotube coating

Superlubricity, i.e., coefficient of friction (COF) below 0.01, was earlier limited to microscale in controlled environments in the earlier literature and more recently realized for macroscale sliding of ceramic or carbon surfaces lubricated by water or other polar fluids. However, there is lack of report of superlubricity for the most common bearing system, i.e., steel-steel contact in non-polar oil lubrication. Here, in this work, we present ultra-low COF of 0.001–0.007 by using a sacrificial coating composed of vertically-aligned carbon nanotubes (CNTs) for macroscale steel-steel sliding under minimum quantity lubrication (MQL) of a polyalphaolefin (PAO) oil in the ambient environment. Raman spectroscopy and electron microscopy analyses detected graphene-containing tribofilms on both the steel surfaces, which was produced by the fractured CNT flakes and metallic wear debris during running-in. The in situ formed graphene-graphene contact interface presumably possesses a low shear resistance leading to superlubricity. The presence of oil, despite as little as one droplet, has proven to be crucial. Such a superlubricity performance has shown good sustainability in extended testing of more than 500,000 cycles and strong ability of accommodating changes in sliding conditions. Results here demonstrate feasibility with fundamental insights for achieving ambient environment macroscale superlubricity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coulomb blockade effects in a topological insulator grown on a high- T c cuprate superconductor

The evidence for proximity-induced superconductivity in heterostructures of topological insulators and high- T c cuprates has been intensely debated. We use molecular-beam epitaxy to grow thin films of topological insulator Bi 2 Te 3 on a cuprate Bi 2 Sr 2 CaCu 2 O 8+x , and study the surface of Bi 2 Te 3 using low-temperature scanning tunneling microscopy and spectroscopy. In few unit-cell thick Bi 2 Te 3 films, we find a V-shaped gap-like feature at the Fermi energy in d I /d V spectra. By reducing the coverage of Bi 2 Te 3 films to create nanoscale islands, we discover that this spectral feature dramatically evolves into a much larger hard gap, which can be understood as a Coulomb blockade gap. This conclusion is supported by the evolution of d I /d V spectra with the lateral size of Bi 2 Te 3 islands, as well as by topographic measurements that show an additional barrier separating Bi 2 Te 3 and Bi 2 Sr 2 CaCu 2 O 8+x . We conclude that the prominent gap-like feature in d I /d V spectra in Bi 2 Te 3 films is not a proximity-induced superconducting gap. Instead, it can be explained by Coulomb blockade effects, which take into account additional resistive and capacitive coupling at the interface. Our experiments provide a fresh insight into the tunneling measurements of complex heterostructures with buried interfaces.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Ion irradiation induced crystalline disorder accelerates interfacial phonon conversion and reduces thermal boundary resistance

Traditional understanding of the thermal boundary resistance (TBR) across solid-solid interfaces posits that the vibrational densities of states overlap between materials dictates interfacial energy transport, with phonon scattering occurring at the interface. Using atomistic simulations, we show a mechanism for control of TBR; point defects near an interface can lead to both short- and midrange disorder, accelerating the conversion of vibrational energy between bulk and interfacial modes, ultimately reducing the TBR. In conclusion, we experimentally demonstrate this reduction through ion irradiation of gallium nitride and subsequently measuring the TBR across Al/GaN interfaces.

Pfeifer, Thomas W.↗
DOE OSTI2021

Towards replacing physical testing of granular materials with a Topology-based Model

In the study of packed granular materials, the performance of a sample (e.g., the detonation of a high-energy explosive) often correlates to measurements of a fluid flowing through it. The “effective surface area,” the surface area accessible to the airflow, is typically measured using a permeametry apparatus that relates the flow conductance to the permeable surface area via the Carman-Kozeny equation. This equation allows calculating the flow rate of a fluid flowing through the granules packed in the sample for a given pressure drop. However, Carman-Kozeny makes inherent assumptions about tunnel shapes and flow paths that may not accurately hold in situations where the particles possess a wide distribution in shapes, sizes, and aspect ratios, as is true with many powdered systems of technological and commercial interest. To address this challenge, we replicate these measurements virtually on micro-CT images of the powdered material, introducing a new Pore Network Model based on the skeleton of the Morse-Smale complex. Pores are identified as basins of the complex, their incidence encodes adjacency, and the conductivity of the capillary between them is computed from the cross-section at their interface. We build and solve a resistive network to compute an approximate laminar fluid flow through the pore structure. Here, we provide two means of estimating flow-permeable surface area: (i) by direct computation of conductivity, and (ii) by identifying dead-ends in the flow coupled with isosurface extraction and the application of the Carman-Kozeny equation, with the aim of establishing consistency over a range of particle shapes, sizes, porosity levels, and void distribution patterns.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synthesis and characterization of electron beam irradiation-induced damage in polycrystalline metal thin films

High-energy physics research, industrial sterilizing, and material processing depend extensively on electron beam accelerators. Exit windows are crucial components of such electron accelerator systems, maintaining vacuum integrity inside the machine while providing mechanical strength, thermal stability, and radiation resistance at the beam-target interface. In this study, thin metallic films of Ni, Ti, Cr, and V were explored for use in electron beam exit windows, and their properties were compared with the properties of their bulk counterparts. Simulation results of metal foils predicted Ti to exhibit less beam power dissipation compared to Ni. However, Ni possesses superior mechanical and structural properties compared to Ti. The performance of these films under electron beam irradiation was examined by depositing thin layers of these films on silicon and metallic substrates using magnetron sputtering and exposing them to e-beam irradiation in a controlled setup. The deposited films were subjected to a dose of approximately 66 kGy at a beam energy of 10 MeV and characterized prior to and postexposure to the beam using field emission scanning electron microscopy, atomic force microscopy, x-ray diffraction (XRD), and nanoindentation. Particular emphasis was given to characteristics like the grain structure, surface morphology, dislocation density, and hardness. XRD patterns revealed irradiation-induced changes in peak intensities, while the crystallinity remained largely unchanged. Nanoindentation results showed that the pristine and irradiated Ti and Ni films were twice as hard when compared to bulk Ti and Ni samples, regardless of the substrate type used (Si or bulk Ti, or Ni). These results emphasize the superior mechanical properties of thin metal films compared to their bulk counterparts. In conclusion, this study advances the optimization of thin film materials for robust and efficient e-beam applications, ensuring improved durability and operational reliability.

AFM↗
DOE OSTI2021

3D Printed, Low Tortuosity Garnet Framework For Beyond 500 Wh/kg Batteries

In this project, we developed LLZO garnet ink recipes and processes for 3D-printing highly ordered ionically conductive garnet porous structures on dense garnet separators. Using this technique, we are able to fabricate controlled architecture LLZO garnet solid-state electrolyte (SSE) trilayers for application in solid-state lithium batteries. The trilayer comprises a thin dense center layer sandwiched between a 3D-printed patterned porous layer and a random porous layer. The dense layer functions as the ionic separator between the anode and cathode. The random porous layer hosts the lithium-metal anode and provides the structural support. The 3D-printed SSE patterned porous layer hosts the cathode, providing continuous, low tortuosity pathways for fast 3D Li+ transport through the cell while increasing the electrode/electrolyte interface area to decrease the interfacial resistance. Compared to the random porous structure, this ordered patterned structure possesses more vacant space for higher cathode loading without sacrificing ionically conducting capability, thus potentially greatly increasing the cell energy density. For demonstration purposes, we developed two patterns for the 3D-printed porous layer: grids and columns, for hosting sulfur and NMC cathode, respectively. The corresponding two types of cells were fabricated and tested, and have demonstrated achievement of theoretical discharge capacity without cathode calendaring. In addition, we developed a fundamental solid-state ionic and electronic transport model to optimize the 3D-printed structures for maximum energy and power density. The model was validated by experiment and provides the critical design criteria for achieving the >500 Wh/kg energy goal as function of C-rate.

25 ENERGY STORAGE↗
DOE OSTI2024

Robust Dissimilar Metal Friction Welded Spool for Enhanced Capability for Steam Power Components (Final Program Report)

This project successfully demonstrated the feasibility and advantages of producing durable, friction-welded dissimilar-metal spools, both with and without transition pieces, as well as the use of advanced oxidation-protective coatings for steam power applications. The work encompassed the optimization and full-scale production of NFA tubing, overcoming manufacturing and processing challenges to achieve enhanced strength, creep, and fatigue properties validated by extensive microstructural characterization. Optimized welding techniques were developed and refined for joining dissimilar materials, resulting in defect-free welds optimized for both low- and high-pressure boiler circuits. Systematic evaluation of welding parameters, coupled with heat treatments, ensured reliable performance and minimized weld defects such as banding and cracking. Comprehensive mechanical and non-destructive testing, including tensile, bend, fatigue, and CT scanning, confirmed the superior integrity and durability of the friction-welded joints under representative service conditions. To address oxidation-related degradation, a range of protective alloy coatings—such as IN625, APMT, Duplex 2507, and FeCrAlY—were selected and evaluated for their ability to counteract oxide notch formation at dissimilar metal interfaces. These coatings demonstrated improved oxidation resistance and long-term stability under thermal cycling, thereby extending weld service life. Thermal cyclic testing and long-term studies captured the phase stability and diffusion behavior of coated and uncoated configurations. Validated models for low-cycle fatigue (LCF), creep, and thermal mechanical fatigue (TMF) were developed to predict component life and failure modes. These models confirmed that friction-welded configurations exhibited significantly enhanced performance compared to conventional gas-tungsten arc welding (GTAW), with up to 7× improvement in creep resistance and at least 2× enhancement in fatigue properties. The introduction of a tailored transition piece further reduced thermally induced strains, enhancing fatigue life. The results demonstrate a robust pathway for retrofitting existing steam fleet components and upgrading future equipment to deliver substantially improved cold-start cycling behavior and reduction of unplanned outages due to premature weld failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Intrinsic Photoconductivity of few-layered ZrS 2 Phototransistors via Multiterminal Measurements

We report intrinsic photoconductivity studies on one of the least examined layered compounds, ZrS 2 .Few-atomic layer ZrS 2 field-effect transistors were fabricated on the Si/SiO 2 substrate and photoconductivity measurements were performed using both two- and four-terminal configurations under the illumination of 532 nm laser source. We measured photocurrent as a function of the incident optical power at several source-drain (bias) voltages. We observe a significantly large photoconductivity when measured in the multiterminal (four-terminal) configuration compared to that in the two-terminal configuration. For an incident optical power of 90 nW, the estimated photosensitivity and the external quantum efficiency (EQE) measured in two-terminal configuration are 0.5 A/W and 120%, respectively, under a bias voltage of 650 mV. Under the same conditions, the four-terminal measurements result in much higher values for both the photoresponsivity (R) and EQE to 6 A/W and 1400%, respectively. This significant improvement in photoresponsivity and EQE in the four-terminal configuration may have been influenced by the reduction of contact resistance at the metal-semiconductor interface, which greatly impacts the carrier mobility of low conducting materials. This suggests that photoconductivity measurements performed through the two-terminal configuration in previous studies on ZrS 2 and other 2D materials have severely underestimated the true intrinsic properties of transition metal dichalcogenides and their remarkable potential for optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Measurement of shunt resistance and conduction band offset in Cu(In,Ga)Se 2 solar cells through joint analysis of temperature and intensity dependence of open-circuit voltage and photoluminescence

Joint analysis studies of open-circuit voltage and photoluminescence intensity (PL-I) are reported for CuIn 1-x GaxSe 2 (CIGSe) solar cells. A range of compositions are investigated, including constant x=0.35 and x=0.55 as well as a graded composition profile having a minimum of x=0.25. Both the open circuit voltage and PL-I are measured as functions of temperature and illumination intensity. With these two measurements, a full model-based fitting of the temperature and illumination dependence allows extraction of the effects of window layer band offset and shunt resistance, in addition to bulk and interface recombination parameters. Finally, to quantitatively analyze the two distinct measurements jointly, the absolute PL-I is measured to obtain quasi-Fermi-level splitting.

14 SOLAR ENERGY↗