Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interdigitated”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Assessing UV-Induced Degradation in Bifacial Modules of Different Cell Technologies

Bifacial technology enables solar cells to offer higher power output and lower levelized cost of energy compared to their monofacial counterparts. Here, we examined the adverse effects of ultraviolet-induced degradation (UVID) on a variety of high-efficiency silicon wafer-based bifacial cell technologies, including silicon heterojunction (SHJ), interdigitated back contact (IBC), passivated emitter rear contact (PERC), and passivated emitter rear totally-diffused (PERT). Both the front and rear sides of bifacial cells without any encapsulation were exposed to an artificially accelerated UV exposure test. After 2000 h of UV irradiation, the bifacial cells exhibited greater power loss with backside exposure indicating potential sensitivity of the rear passivation to UV. The highest power degradation is observed in SHJ cells, followed by p-PERC and n-PERT cell technologies. The degradation in SHJ cells is attributed to the reduction in V oc and FF, while the degradation in p-PERC and n-PERT cells is correlated with a significant drop in I sc . This suggests that each cell type/make degrades via different degradation pathways.

bifacial cells↗
DOE OSTI2021

UV-Induced Degradation of High-Efficiency Solar Cells with Different Architectures

The ultraviolet-induced degradation (UVID) of solar panels is associated with the deterioration of cell performance and reduced reliability of packaging materials. Here we examine the UV stability of different architectures of high-efficiency solar cells without any encapsulation. Identical UV exposure tests were performed at two different labs using UVA-340 fluorescent lamps under different electrical bias configurations (open- or short-circuit) and irradiated cell surfaces (for bifacial technologies). Cell technologies, including heterojunction (HJ), interdigitated back-contact cells (IBC), passivated emitter rear contact (PERC), passivated emitter rear totally-diffused (PERT), are found to be more susceptible to UVID, leading to significant Isc loss (up to 4%) and P max loss (up to 15%) as compared to the conventional back surface field (Al-BSF) cells after exposure to UV irradiation of 8.92 MJ-m -2 -nm -1 at 340 nm. Additionally, the bifacial cells when irradiated from the backside exhibited greater photocurrent loss compared to the front side exposure, indicating potential sensitivity of rear surface passivation to UV radiation.

crystalline silicon↗
DOE OSTI2023

Quasiparticle Generation-Recombination Noise in the Limit of Low Detector Volume

We have measured the quasiparticle generation-recombination (GR) noise in aluminium lumped element kinetic inductors with a wide range of detector volumes at various temperatures. The basic detector consists of meandering inductor and interdigitated capacitor fingers. The inductor volume is varied from 2 to 153 mu m(3) by changing the inductor width and length to maintain a constant inductance. We started with measuring the power spectrum density (PSD) of the detectors frequency noise which is a function of GR noise and we clearly observed the spectrum roll off at 10 kHz which corresponds to the quasiparticle lifetime. Using data from a temperature sweep of the resonator frequency we convert the frequency fluctuation to quasiparticle fluctuation and observe its strong dependence on detector volume: detectors with smaller volume display less quasiparticle noise amplitude. Meanwhile we observe a saturated quasiparticle density at low temperature from all detectors as the quasiparticle life time tqp approaches a constant value at low temperature.

Li, Juliang↗
DOE OSTI2024

Development of an MKID frequency-to-pixel LED mapper for SPT-3G+

SPT-3G+ is the next-generation camera for the South Pole Telescope (SPT). SPT is designed to measure the cosmic microwave background (CMB) and the mm/sub-mm sky. The planned focal plane consists of 34,000 microwave kinetic inductance detectors (MKIDs), divided among three observing bands centered at 220, 285, and 345 GHz. Each readout line is designed to measure 800 MKIDs over a 500 MHz bandwidth, which places stringent constraints on the accuracy of the frequency placement required to limit resonator collisions that reduce the overall detector yield. To meet this constraint, we are developing a two-step process that first optically maps the resonance to a physical pixel location, and then next trims the interdigitated capacitor (IDC) to adjust the resonator frequency. We present a cryogenic LED apparatus operable at 300 mK for the optical illumination of SPT-3G+ detector arrays. We demonstrate integration of the LED controls with the GHz readout electronics (RF-ICE) to take data on an array of prototype SPT-3G+ detectors. We show that this technique is useful for characterizing defects in the resonator frequency across the detector array and will allow for improvements in the detector yield.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Remote sensing of cytotype and its consequences for canopy damage in quaking aspen

Abstract Mapping geographic mosaics of genetic variation and their consequences via genotype x environment interactions at large extents and high resolution has been limited by the scalability of DNA sequencing. Here, we address this challenge for cytotype (chromosome copy number) variation in quaking aspen, a drought‐impacted foundation tree species. We integrate airborne imaging spectroscopy data with ground‐based DNA sequencing data and canopy damage data in 391 km 2 of southwestern Colorado. We show that (1) aspen cover and cytotype can be remotely sensed at 1 m spatial resolution, (2) the geographic mosaic of cytotypes is heterogeneous and interdigitated, (3) triploids have higher leaf nitrogen, canopy water content, and carbon isotope shifts (δ 13 C) than diploids, and (4) canopy damage varies among cytotypes and depends on interactions with topography, canopy height, and trait variables. Triploids are at higher risk in hotter and drier conditions.

Blonder, Benjamin↗
DOE OSTI2021

Transition to Online Cable Insulation Condition Monitoring

Nuclear power plant cables were originally qualified for 40 year life and generally have not required specific test verification to assure service availability through the initial plant qualification period. However, license renewals to 60 and 80 years of operation require a cable aging management program that depends on some form of test and verification to assure fitness for service. Environmental stress (temperature, radiation, chemicals, water, and mechanical) varies dramatically within a nuclear power plant and, in some cases, cables have degraded and required repair or replacement before their qualified end-of-life period. In other cases, cable conditions have been mild and dependable cable performance confirmed to extend well beyond the initial qualified life. Most offline performance-based testing requires cables to be de-coupled and de-energized for specially trained technicians to perform testing. These offline tests constitute an expensive operational burden that limits the economic viability of nuclear power plants. Although initial investment may be higher, new online test practices are emerging as options or complements to offline testing that avoid or minimize the regularly scheduled offline test burden. These online methods include electrical and fiber-optic partial discharge measurement, spread spectrum time or frequency domain reflectometry, distributed temperature profile measurements, and local interdigital capacitance measurement of insulation characteristics. Introduction of these methods must be supported by research to confirm efficacy plus either publicly financed or market driven investment to support the start-up expense of cost-effective instrumentation to monitor cable condition and assure reliable operation. This work summarizes various online cable assessment technologies plus introduces a new cable motor test bed to assess some of these technologies in a controlled test environment.

Glass, Samuel W.↗
DOE OSTI2020

Ultrahigh areal number density solid-state on-chip microsupercapacitors via electrohydrodynamic jet printing

Microsupercapacitors (MSCs) have garnered considerable attention as a promising power source for microelectronics and miniaturized portable/wearable devices. However, their practical application has been hindered by the manufacturing complexity and dimensional limits. Here, we develop a new class of ultrahigh areal number density solid-state MSCs (UHD SS–MSCs) on a chip via electrohydrodynamic (EHD) jet printing. This is, to the best of our knowledge, the first study to exploit EHD jet printing in the MSCs. The activated carbon-based electrode inks are EHD jet-printed, creating interdigitated electrodes with fine feature sizes. Subsequently, a drying-free, ultraviolet-cured solid-state gel electrolyte is introduced to ensure electrochemical isolation between the SS–MSCs, enabling dense SS–MSC integration with on-demand (in-series/in-parallel) cell connection on a chip. The resulting on-chip UHD SS–MSCs exhibit exceptional areal number density [36 unit cells integrated on a chip (area = 8.0 mm x 8.2 mm), 54.9 cells cm -2 ] and areal operating voltage (65.9 V cm -2 ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Characterization of Electrochemical Behavior for Aqueous Organic Redox Flow Batteries

Use of aqueous redox flow batteries with organic redox-active materials holds great promise for large-scale and sustainable energy storage. The development of low-cost, highly efficient aqueous redox flow batteries lies in a comprehensive understanding of the electrochemical behaviors of redox-active compounds. In this work, an alkaline redox battery with organic dihydroxyphenazine sulfonate (DHPS) anolyte and ferro-/ferricyanide (Fe(CN) 6 ) catholyte is investigated as a typical example of aqueous redox flow batteries using organic redox-active materials. The electrochemical kinetics of DHPS and Fe(CN) 6 are separately characterized using the symmetrical cell design. The resistance components are calculated directly from the experimental measurement. The key kinetic parameters are extracted and compared for DHPS and Fe(CN) 6 electrolytes. The extracted parameters are validated with symmetrical and full flow cell simulations at different operating conditions. Key parameters and internal loss are also compared with all-vanadium redox flow batteries, representing current state of the art. In addition, our extracted key parameters from a symmetrical flow cell are compared with the measured key parameters by cyclic voltammetry, a widely deployed electroanalytical technique. The cell performance prediction of DHPS anolyte on a 780 cm 2 interdigitated cell is made and found the power density is peaked at 475 mW cm -2 at our measurement condition.

25 ENERGY STORAGE↗
DOE OSTI2023

Electrochemical Residence Time Distribution as a Diagnostic Tool for Redox Flow Batteries

The fluid dynamic and electrochemical performance of redox flow batteries (RFBs) stems from the relationship between the flow field and the porous electrode, whose interplay determines how active species move and react during device operation. While characterization techniques, such as residence time distribution, offer insights into species mobility within a reactive volume for a traditional chemical reactor, electrochemical reactors also enable simultaneous measurement of the redox reactions, unlocking another dimension of analysis. Herein, we demonstrate how potentiodynamic measurements, using injections of electrolyte examined through moment analysis, can provide electrode-specific performance scaling relationships across a matrix of carbon paper and cloth electrodes with flow through and interdigitated flow fields. We further combine experimental campaigns with multiphysics simulations to demonstrate how electrode surface area can be estimated with this technique, which we then validate with activated and unactivated commercial carbon cloth electrodes. These studies reveal the multiscale observations that potentiodynamic measurements afford, augmenting existing electrochemical techniques for holistic electrochemical reactor diagnostics.

Electrochemistry↗
DOE OSTI2024

Topology Optimization for Full-Cell Electrochemical Energy Storage Device

This code is used to conduct topology optimization of a general full cell energy storage device. The anode and cathode designs are optimized simultaneously, allowing possibility for interdigitation. The charging mechanism can consist of both electric double layer charging (EDLC) typically observed in capacitors and redox reaction typically observed in batteries.

Roy, Thomas↗
DOE OSTI2021

Effect of micron-scale manufacturing flaws on the tensile response of centimeter sized two-photon polymerization microlattices

Two-photon polymerization (TPP) is a unique fabrication technique that enables sub-micron scale resolution. Herein, we report on uniaxial tensile tests on millimeter-sized TPP log-pile structures that were fabricated using a recently developed interdigitated stitching strategy. As expected, the Young’s modulus increased with laser intensity, however elastic modulus, ultimate strength and strain-at-failure varied widely, even for nominally identical samples. Post-mortem analysis revealed a series of print defects resulting from various sources including misalignments, resin shrinkage, laser beam shadowing, and local depletion of the oxygen inhibitor. While some of the defects can be eliminated, such as misalignments due to insufficient precision of the mechanical stage, others are more intrinsic to TPP and thus more difficult to address.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Rapid Patterning and Advanced Device Structures for Low Cost Manufacturable Crystalline Si IBC Cells

Recent record efficiency Si cells have had an interdigitated back contact (IBC) design where both positive and negative contacts are fabricated on the back side of the Si wafer. Many industry groups have investigated IBC cells but used photolithography to pattern the rear contacts although it is considered impractical for low cost, high volume manufacturing. Alternative patterning methods using lasers and mechanical masking have been utilized in fabrication of patterned regions in IBC Si solar cells to replace photolithography. Another exciting advance in Si solar cell technology has been replacing the high temperature diffusion of doped regions inside the crystalline Si wafer with low temperature deposition of very thin layers of doped amorphous hydrogenated Si (a-Si:H) on the Si wafer. This is called a Si heterojunction (HJ) device. The a-Si:H provides excellent passivation of surface defects and has produced the highest open circuit voltages (VOC) of any Si solar cell device structure. The Institute of Energy Conversion (IEC) demonstrated the first IBC-HJ solar cell combining these two strategies in 2007 and has fabricated IBC-HJ cells with 20% efficiency using three photolithography steps. Despite the demonstrated efficiency potential of this device by industry groups (>26%) there is no commercial production because of the challenges of patterning and processing the structure in an industrial environment. Our work sought to address that challenge. The objective of this 3 year project was to develop the processing for the IBC-HJ Si solar cell using lasers for patterning and contact formation instead of photolithography. Laser patterning enables rapid, contactless manufacturing of patterned regions. We intensively studied laser fired contacts, laser patterning of the a-Si multi-layer stacks and metal layers and the use of plasma shadow masks. After an exhaustive focus in the first year on the laser fired emitter (LFE) and contact (LFC), we were unable to achieve VOC greater than 660 mV, compared to the 720 mV required to meet our milestones. We discovered that an additional issue with our original IBC structure was the presence of an inversion layer at the back surface connecting the p and n regions which reduced the VOC and fill factor (FF). We developed innovative methods for characterizing the inversion layer. These two limitations in the original design lead to development of a new IBC-HJ process sequence and device structure which we called Plasma Masked Laser Processed (PMLP). It retained the original high efficiency features including manufacturability. The LFC was replaced with a standard n-type a-Si HJ contact. The inversion layer was eliminated by replacing the previous p-type stack in the gap with an n-type or SiN stack. The PMLP used laser ablation of a multi-layer a-Si stack followed by chemical etching to open the n-contact. It required deposition of a patterned stack through a mask in the plasma deposition chamber. This turned out to be a source of significant problems due to inevitable unwanted deposition ‘leakage’ under the mask. This formed a blocking contact on the emitter which significantly reduced Voc and FF. Several iterations in PMLP device structure and chemical etching steps resulted in a large improvements, e.g. the efficiency increasing from 3 to 15% and Voc from 450 to 660 mV but they were unable to completely eliminate it. The best IBC-HJ device we fabricated had only 15% efficiency. For perspective, our standard FHJ devices had 20% efficiency.

14 SOLAR ENERGY↗
DOE OSTI2020

Impact of undoped substrates on high performance silicon solar cells

Today's highest-efficiency silicon solar cells typically operate near the threshold between low-level and high-level injection. It is not well understood if pushing further into a regime in which the cell operating point is solidly in high-level injection at all times of the day has further benefits for the solar cell performance. From a reliability perspective, cells fabricated on lower doped silicon have a larger breakdown voltage. This advantage can affect the design of modules allowing higher voltages and a relaxation of the number of bypass diodes needed. In this project, we present a comprehensive assessment, both experimental and using simulation, of how bulk resistivity, light intensity, and operation temperature impact the performance of the silicon solar cell. This work incorporates a comprehensive device physics analysis assisted by numerical simulation. The source code is now available under General Public License (GPL3), and to further leverage the findings of this project and outreach people outside of the scientific community, we are working with www.pveducation.org (which receives >1 million visitors a year) to create interactive content using our simulation results. The simulation results indicate that high bulk resistivity wafers (>>10 Ωcm) require bulk Shockley-Read-Hall (SRH) lifetimes in the millisecond range to outperform wafers with standard bulk resistivities (<10 Ωcm). Additionally, above bulk resistivities of 10 Ωcm (the exact value depends on the bulk characteristics of the wafer), the cell efficiency is weakly dependent on the bulk resistivity. As a result, ingot manufactures may have an opportunity to further reduce wafer cost by growing higher resistivity ingots that are more tolerant to resistivity variations. This project is particularly relevant today, as solar cell architectures with improved surface passivation and milliseconds lifetimes wafers are commercially available, leveraging potential benefits of using higher bulk resistivities. Outside of interdigitated back contact (IBC) cell, reported studies on high resistivity silicon (>100 Ωcm) are very limited. To the best of our knowledge, this project provides for the first-time experimental insight on solar cells fabricated on wafers with bulk resistivities up to several thousand Ωcm, delivering a comprehensive vision of their performance under real-world temperature and light intensity operation conditions. We manufactured and characterized solar cells with bulk resistivities in the range of 1 Ωcm to >15k Ωcm. Under standard testing conditions (STC), we measured solar cells efficiencies over 20% over the entire range of bulk resistivities, using our baseline cell processing. To evaluate the cell performance in real-world operation conditions, the solar cells were measured at different temperatures (25-80°C) and at different light intensities (0.1-1 suns). The measurements show that the bulk resistivity does not impact the solar cell response to temperature and light intensity. Similar thermal coefficients (TC) were measured for standard and high bulk resistivities, and they are comparable with the TC values reported in the literature for standard bulk resistivities <10 Ωcm. After light soaking, the solar cell didn’t show signs of light-induced degradation (LID). This result was expected since n-type float zone (FZ) wafers were used in this work, i.e. low traces of boron and low concentration of oxygen (oxygen is typically found in the seed end of Czochralski (CZ) ingots). We measured for high bulk resistivities (>10 Ωcm) extremely high breakdown voltages (>1000V). In conclusion, the insight provided by this project can positively impact the levelized cost of energy (LCOE) of the photovoltaic systems through its effect on cell and ingot manufacturing yield, silicon cell power output, and module reliability.

14 SOLAR ENERGY↗
DOE OSTI2021

VTO_2021_APR_LLNL_Ye

Traditional batteries are composed of two-dimensional films that are stacked and/or rolled. Thin film batteries display high power density while their thick film counterparts show good energy density, but it has proven difficult to concurrently achieve both within these planar form factors. In addition, conventional Li-ion batteries based on liquid organic electrolytes or gel polymer electrolytes have raised severe safety concerns due to the intrinsic flammable properties of the organic electrolytes. They are also not ideal for the use of high energy density metallic lithium (Li) anodes due to Li dendrite growth, or sulfur cathodes due to shuttling effects that result in fast capacity fade. There is an urgent need to develop safe, high-performance solid-state batteries (SSBs) with advanced electrolyte and separator technologies. Although in recent years a series of superionic conductors have been developed for electrolytes and separators, their performance does not satisfy demanding criteria due to large impedance from poor solid electrolyte-electrode contact and questionable electrochemical and mechanical stability. Unlike the well-established roll-to-roll fabrication of conventional Li-ion batteries, the processing of SSBs is unique due to the brittleness of solid-state electrolytes (SSEs). The commercially available or lab-developed SSE discs are usually very thick (hundreds of micrometers to millimeters) to overcome their brittle nature, which unfortunately increases the cell impedance and accounts for the majority of the overall cell weight and volume, leading to dramatically decreased power and energy densities. In this project, we will investigate 3D printing techniques to overcome safety, fabrication, mechanical, and electrochemical issues in SSBs. 3D printing builds complex structures in a layer-by-layer fashion, which allows rapid production of hierarchical architectures, gradient and multi-material structures, and multi-component assemblies. 3D printing is an emerging area that could fundamentally transform energy storage devices. For example, 3D printing can produce batteries with arbitrary form factors to fit a product’s specific volume requirements and can create interwoven electrode arrangements over a wide range of length scales to improve transport and increase power density for a given energy density. For SSBs, 3D printing may dramatically reduce the separator thickness from ~1 mm (by hydraulic pressing) to tens of micrometers or less. In addition, the interfacial contact area between the electrolyte and the electrode may be increased via 3D interdigitated designs. Hence, we expect a significant reduction of the overall cell impedance and enhancement of both energy and power densities of SSBs by harnessing an array of 3D printing technologies being developed at Lawrence Livermore National Laboratory (LLNL).

25 ENERGY STORAGE↗
DOE OSTI2021

Surface Acoustic Wave Sensors for Refrigerant Leak Detection: Compact, Inexpensive, Selective and Sensitive Sensors

Pacific Northwest National Laboratory (PNNL), in collaboration with Parker and Hannifin, is developing a compact, inexpensive, and highly sensitive and selective surface acoustic wave sensor coated with fluorophillic sorbent for detecting fluorocarbon leaks from HVAC systems. Having a highly effective sorbent sensitive to fluorocarbon refrigerant vapors provides a means to develop a sensing device for leak detection. Surface acoustic wave (SAW) sensors with a gas sensing film deposited between the delay lines or on the interdigital transducer have been used to detect gas and vapor molecules in harsh environments with high sensitivity. As part of this project, PNNL screened several sorbent materials that are shown to be selective towards fluorocarbon refrigerant (R32) molecule. The identified sorbent materials were synthesized, characterized, and tested towards R32 using various spectroscopic technique. Next, the sorbent material was coated on a SAW sensor as a thin film using vapor deposition and drop coating methods. The coated thin film was further characterized and tested towards the detection of pure R32 and R32 in ambient air at room temperature to demonstrate the SAW response towards R32 in presence of other competing gases and vapors in air.

42 ENGINEERING↗
DOE OSTI2023

Hybrid Tandem Photovoltaics

Tandem solar cell structures are the only strategy demonstrated to surpass the detailed balance efficiency limit of high-quality single-junction solar cells. To continue to improve the efficiencies of cost-effective terrestrial solar power, hybrid tandems of dissimilar subcells are being considered by many around the world, especially designs that incorporate silicon solar cells as a bottom subcell. In this project, we studied a wide variety of tandem design possibilities including those with three-terminal (3T) and four-terminal (4T) configurations. The use of 3T and 4T designs could be useful for efficient and economical hybrid tandem designs that utilize the best available subcell materials such as emerging perovskite materials. Three-terminal configurations, in particular, have not been sufficiently studied previously. We have laid the foundational groundwork in this project for understanding the operation of 3T tandems: developing a taxonomy for naming, a methodology for measuring and interconnecting, and models for simply characterizing 3T tandems. Electrical and optical subcell coupling between the subcells was also measured and modeled. An important part of this work was the fabrication of novel example tandem structures, including 4T GaAs/Si, 3T GaInP/Si, 3T GaAs/Si, and 3T GaInP/GaAs devices. Using these high-quality tandem cells, we have been able to clearly demonstrate the achievability of high-efficiencies, and subtle physical effects such as photon recycling and luminescent coupling. We have developed and demonstrated essential building-block tools such as transparent conductive adhesives (TCA) and 3T silicon bottom cells with interdigitated back contacts (IBC) that can also be used in many other tandem designs. We have tested the reliability of these tools and devices under standardized testing and outdoor measurements. We have found 4T GaAs/Si tandems to be relatively straightforward to fabricate and robust in real-world outdoor conditions. While we have demonstrated working hybrid 3T III-V/TCA/Si IBC tandems, we experienced low yields even with our best process flows yet. Further work is still needed to improve the processing yield of these devices. We therefore also created tandem cells using an all-III-V 3T tandem process which was very robust with high yields, allowing for the creation of voltage-matched strings in many different configurations using 8 nearly identical 3T tandems. Using these robust 3T tandem examples, we were able measure and precisely characterize 3T tandem behaviors to predict their operation under changing spectrum and temperature. The optoelectronic equivalent-circuit model was shown to be very general and applicable to hybrid tandems, and encompassed the operation 3T Si IBC cells. This general model has been distributed to the public in as open-source Python-based software called PVcircuit. We have calculated the implications of these new tandem device designs on the real-world energy production and shown how the relative performance of different tandem configurations is situational and can be engineered using the tools developed here.

14 SOLAR ENERGY↗
DOE OSTI2026

Towards Spatial Control of Reaction Selectivity on Photocatalysts using Area Selective Atomic Layer Deposition on Model Dual Site Electrocatalyst Platform

Photocatalytic water splitting is a promising route to low-cost H2; however, this approach is currently limited by solar-to-hydrogen (STH) conversion efficiencies in the sub-10% range. Z-scheme water splitting, in which H2 and O2 evolving particles are operated in separate compartments and electronically coupled by a soluble redox mediator, offers improvements in STH efficiency but introduces high rates of undesired side and back reactions. Nanoscopic oxide coatings (e.g., CrOx, and SiOx) have previously been used to selectively block undesired reactants from reaching active sites; however, a coating encapsulating the entire photocatalyst particle limits activity as the particle can no longer facilitate both half reactions. In contrast to photodeposition, which may produce non-uniform overlayers due to the difficulty of controlling local electrochemical reactivity on the surface, area-selective atomic layer deposition (AS-ALD) can be used to deposit conformal ultrathin oxide coatings while preserving access to non-growth areas of a substrate surface. To develop this technique for Z-scheme photocatalysts, we performed AS-ALD of TiO2 on a dual site planar electrocatalyst based on interdigitated arrays of Pt and Au. Self-assembled monolayers of 1-octadecanethiol (ODT) were used to block growth on the Au array, resulting in a patterned surface in which only the Pt sites were encapsulated with TiO2. These electrocatalysts demonstrated localized reaction selectivity for hydrogen evolution reaction (HER) over the TiO2/Pt sites, while the uncoated Au sites retained activity towards Fe(II)/Fe(III) redox (FeRR). Under independent potential control, these microelectrodes showed that selectively deposited TiO2 coatings can suppress the rate of back reactions on neighboring active sites by an order of magnitude compared to uncoated control samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Determination of Thermal Damage Threshold in THz Photomixers Using Raman Spectroscopy

The increase of device lifetime and reliability of THz photomixers will play an essential role in their possible future application. Therefore, their optimal work conditions/operation range, i.e., the maximal incident optical power should be experimentally estimated. We fabricated and tested THz photomixer devices based on nitrogen-implanted GaAs integrated with a Bragg reflector. Raman spectroscopy was applied to investigate the material properties and to disclose any reversible or irreversible material changes. The results indicate that degradation effects in the photomixer structures/material could be avoided if the total optical power density does not exceed levels of about 0.7 mW/µm 2 for 100 min of operation. Furthermore, the investigations performed during 1000 min of optical exposure on the photomixer devices’ central region comprising interdigitated metal-semiconductor-metal (MSM) structures suggest a reversible “curing” mechanism if the power density level of ~0.58 mW/µm 2 is not exceeded. Long-term operation (up to 1000 h) reveals that the photomixer structures can withstand an average optical power density of up to ~0.4 mW/µm 2 without degradation when biased at 10 V. Besides the decrease of the position of the A1g (LO) Raman mode from ~291 cm -1 down to ~288 cm -1 with increasing optical power density and operation time, broad Raman modes evolve at about 210 cm -1 , which can be attributed to degradation effects in the active photomixer/MSM area. In addition, the performed carrier lifetime and photomixer experiments demonstrated that these structures generated continuous wave sub-THz radiation efficiently as long as their optimal work conditions/operation range were within the limits established by our Raman studies.

36 MATERIALS SCIENCE↗