Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hardening rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Link statistics of dislocation network during strain hardening

Dislocations are line defects in crystals that multiply and self-organize into a complex network during strain hardening. The length of dislocation links, connecting neighboring nodes within this network, contains crucial information about the evolving dislocation microstructure. By analyzing data from Discrete Dislocation Dynamics (DDD) simulations in face-centered cubic (fcc) Cu, we characterize the statistical distribution of link lengths of dislocation networks during strain hardening on individual slip systems. Here, our analysis reveals that link lengths on active slip systems follow a double-exponential distribution, while those on inactive slip systems conform to a single-exponential distribution. The distinctive long tail observed in the double-exponential distribution is attributed to the stress-induced bowing out of long links on active slip systems, a feature that disappears upon removal of the applied stress. We further demonstrate that both observed link length distributions can be explained by extending a one-dimensional Poisson process to include different growth functions. Specifically, the double-exponential distribution emerges when the growth rate for links exceeding a critical length becomes super-linear, which aligns with the physical phenomenon of long links bowing out under stress. This work advances our understanding of dislocation microstructure evolution during strain hardening and elucidates the underlying physical mechanisms governing its formation.

Crystal plasticity↗
DOE OSTI2023

Role of Fe in long-range ordered Ni 2 Cr precipitates in Ni-Cr-Fe model alloys during isothermal aging

The precipitation of new phases during long-term service at elevated temperatures is a concern for the thermal stability of engineering alloys. In Ni-Cr-based alloys, e.g., Alloy 690, the formation of long-range ordered Ni 2 Cr causes embrittlement and may impact the lifetime of nuclear power plant components. In this work, we quantify the formation and evolution of Ni 2 Cr precipitation in eleven Ni-Cr-Fe model alloys with 0, 5, 7, and 10wt % Fe contents, and with Ni/Cr atomic ratios of 1.8, 2.0, 2.2, 2.4. These alloys were isothermally aged up to 10,000h at temperatures between 330 and 475°C. The alloys were characterized by synchrotron-based x-ray diffraction and Vickers hardness testing to quantify Ni 2 Cr precipitate size, and the impact of precipitate size on the mechanical properties as a function of Fe content. After 10,000 h of aging at 475°C and 418°C, the formation of Ni 2 Cr was observed in all alloys with 0 and 5wt % Fe. After 10,000h of aging at 418°C, Ni 2 Cr precipitates were also observed in the 7wt % Fe containing Ni/Cr=2.0 sample. Further, no clear evidence of Ni 2 Cr was observed in any of the 10wt % Fe samples at any time and temperature combination. We find that the face-centered cubic matrix lattice contraction and Vickers hardness are correlated with the Ni 2 Cr formation. The greatest change in hardness and lattice contraction occurs in stoichiometric alloys (Ni/Cr=2.0) with 0wt % Fe at 475°C. The rate of change in the material properties for the 5wt % Fe alloys is reduced, however the magnitude of changes is similar to 0wt % Fe alloys. A precipitation hardening model developed for Ni-Cr alloys based on critical resolved shear stress with weakly coupled dislocations shows a clear link between Ni 2 Cr precipitate size and hardness. This trend held across all alloys with Ni 2 Cr formation regardless of Fe concentration. This important structure-property relationship can potentially help define Ni-Cr-Fe-based component lifetimes directly through an understanding of how Ni 2 Cr formation impacts mechanical properties as a function of Fe content.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strain rate sensitivity, microstructure variations, and stress-assisted β → α" phase transformation investigation on the mechanical behavior of dual-phase titanium alloys

In this study, the microstructures of three widely used dual-phase titanium alloys: Ti-6Al-4V, Ti-6Al-2Sn-4Zr-2Mo, and Ti-6Al-2Sn-4Zr-6Mo are characterized using backscatter electron imaging and the deformation behaviors in their individual α and β phases are investigated using in situ high-energy X-ray diffraction during uniaxial tension experiments. This is accompanied by calculation of the strain rate sensitivity (SRS) in these alloys, as a function of applied loading. The results of the calculated SRS and the mechanical response (in terms of lattice strains and hardening behaviors) are rationalized based on the local microstructure, composition, and texture of the alloy. A stress-induced β (BCC) to α" (orthorhombic) phase transformation is observed during the in-situ diffraction experiment, which permitted analysis of the lattice strain evolution during the phase transformation. Results from this study provide insights into the relationship between microstructure, composition, applied loading, and the deformation behavior, including effects on loading with time holds. Specifically, the results show that the microstructure, and not necessarily the chemical composition (Mo content), along with the applied loading have a dominant role in the observed SRS variation in titanium alloys. Further, the evolution of the α" (orthorhombic) phase is observed for the first time during deformation of an industrially relevant titanium alloy, Ti-6246.

36 MATERIALS SCIENCE↗
DOE OSTI2024

ASSESSMENT OF HIGH-VOLUME HARVESTED FLY ASH BLENDS FOR USE IN PRECAST CONSTRUCTION

Declining supplies of fresh fly ashes in some regions have further driven the importance of using harvested fly ash as a supplementary cementitious material and thus replacement for more energy-intensive ordinary Portland cement (OPC). Higher replacement rates of OPC with fly ash in general has traditionally been limited in precast operations due to stringent early-age strength requirements necessitated by initial prestress and lifting/handling of hardened components – often well within 24 hours after fresh concrete placement. Therefore, a series of mix designs were developed, as part of a larger framework for reassessing high-volume fly ash (HVFA) use in the context of precast construction, to demonstrate the feasibility of using larger fractions of harvested fly ash in concrete formulations suitable for precast fabrication demands. More specifically, a target minimum 24-hour compressive strength of 24.1 MPa (3500 psi) was set, in accordance with conventional precast structural design checks, while increasing the fly ash content to 40% replacement of OPC – at least a 15% increase above the traditional limit of 25%. The effect of using more sustainable Type IL cement in contrast to conventional Type III Portland cement (the traditional standard for precast use) – both in conjunction with HVFA use – was also examined. Early-age mechanical properties including compressive strength, modulus of rupture, and modulus of elasticity were evaluated within the aforementioned early-age window. Lastly, corresponding design equations were then reassessed for their applicability with respect to the high-early strength HVFA mixes examined herein.

Gombeda, Matthew J.↗
DOE OSTI2024

Calibration of Al7075 with Plate-Puncture Predictions

The following details calibration of a material model for Al7075-T6511. This aluminum alloy is commonly used across a host of engineering applications. Owing to its widespread prevalence, there is great benefit in improving simulation predictions for this alloy. In the present effort, a calibration is performed of its elastic-plastic response accounting for both rate and temperature dependence. The calibration is informed by a series of tests that include specimens of different geometries tested at different rates and temperatures. All specimens are derived from the same barstock, 3.5 inches in diameter. The fitted model itself uses an anisotropic, Hill yield surface coupled with a Johnson-Cook hardening model. Failure predictions are had by means of a modified Wilkins failure criterion. Following calibration of the material model, a validation exercise is performed against platepuncture experiments. These experiments include multiple probe shapes, probe diameters, and plate thicknesses. The puncture experiments are replicated in simulation with mesh studies performed to assess uncertainty. Key quantities of interest, notably the absorbed energy up to failure, are compared between simulation and experiment providing a means to assess the suitability of the calibration in puncture simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Fast Neutron Irradiation of a Multichannel JFET-Based Optical Encoder

Modern electrical components are susceptible to damage from high levels of radiation and extreme temperatures found near reactors in terrestrial nuclear power plants and in aerospace applications. Radiation-hardened electronics are being developed, largely for the aerospace industry, but they sometimes rely on application-specific, small-batch semiconductor fabrication processes. These processes tend to be prohibitively expensive to develop and maintain outside major industrial facilities or governmental agencies. Recently, commercially available, nonradiation-rated junction-gate field-effect transistors (JFETs) were shown to maintain their functionality at gamma doses exceeding 1 MGy, suggesting that nonrated, commercially available electrical components could be used to develop systems that are tolerant to ionizing radiation. However, gamma ray survival is not indicative of neutron dose survival, and few studies characterize JFETs under neutron irradiation. To address this knowledge gap, a JFET-based analog multiplexer and optical pulsewidth modulation (PWM) encoder was developed and irradiated using a 252 Cf source to 1.6×10 13 n/cm 2 . The multiplexed optical encoder (MOE) system maintained functionality throughout testing and showed little evidence of radiation effects. These results indicate that circuitry tolerant to fast neutron damage can be developed using low-cost, nonradiation-rated, commercially available JFETs, which could provide a lower production cost alternative to specialized semiconductor processes when designing and building electronics better able to survive neutron irradiation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Multifunctional application of nanoscratch technique to characterize cementitious materials

This study aims to further explore the multifunctional applicability of nanoscratch technique to cementitious materials for comprehensive characterization. Based on the investigation of deformation, applied force, and fracture toughness of hardened cement paste during scratching, the methods of phase identification, fracture toughness of individual phase, and the interfacial transition zone (ITZ) thickness quantification were proposed and discussed. After redefining the vertical loading rate of scratching, the slope of the square scratching depth vs. scratching length is recognized as a reliable parameter to distinguish the individual phases for the first time. A fracture toughness-based method is proposed to quantify the thickness of ITZ between clinker and hydrates. Meanwhile, the applicability of phase identification by the scratch method is discussed for different transverse scratching speeds and the vertical loading rates. The findings will benefit the investigation and mechanism understanding of cementitious materials at the microscale by utilizing nanoscratch technique.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experimental Investigation on the Performance Loss of Cross-Linked Polymers During Photo-Oxidative Aging

Abstract Polymeric substances have seen an unprecedented integration in countless applications and fields of life, subjecting them to a broad range of environmental conditions, which can cause a form of damage to the structural and mechanical properties of these components known as aging. In this study we investigate the effects of the degradation of polymeric materials due to the extended exposure to sunlight, which can be simulated through controlled photo-oxidative aging using ultraviolet (UV) radiation as the main catalyst of this phenomenon. The effects on mechanical behavior and chemical properties of four polymeric materials with different mechanical characteristics was accordingly monitored throughout the study. The materials range in hardness with the polyurethane adhesive being the hardest and acting plastically, followed by an acrylic which exhibits greater hardening with time, a polyurethane sealant, which behaves in an elastomeric manner, and a silicon sealant, which is the softest of the set. Samples were prepared and subjected to UV radiation at three different temperatures namely 45, 60 and 80°C, for different aging periods ranging from 1 day for higher temperatures to 150 days for lower ones. The samples were then subjected to the Fourier transform Infrared spectroscopy (FTIR) test to monitor the change in the chemical composition of the materials along the aging durations and conditions. The materials were then subjected to mechanical testing along two modes of mechanical loading, which are a simple tension until failure and a double-cyclic test with progressively increasing strain limits after every two successful cycles until the sample reaches failure. The samples are loaded at constant strain rates throughout both tests. These tests revealed the change of behavior of our materials along the aging periods and conditions. The changes in mechanical behavior vary across each individual material depending on the aging temperature and period, with the changes ranging from hardening to softening, embrittlement or an increase in the maximum strain the material can endure before failure. A general trend would be that most materials become harder after photo-oxidation, however due to the range of temperatures in the aging conditions, thermo-oxidation, which causes softening in some of the polymers, has an increasingly notable effect at higher temperatures. A visible correlation can be noted between the change in mechanical behavior and a change in absorbance of Infrared Radiation (IR) in the FTIR spectrum, as the greater the crosslinking throughout the polymer matrix, the lower the absorbance of IR radiation due to the increased stiffness of the overall macro-molecular structure.

Korayem, Abd-Elrahman↗
DOE OSTI2023

High-pressure response of vibrational properties of b-As x P 1– x : in situ Raman studies

The structural evolution of black arsenic-phosphorous (b-As x P 1–x ) alloys with varying arsenic concentrations was investigated under hydrostatic pressure using in situ Raman spectroscopy. High-pressure experiments were conducted using a diamond anvil cell, which revealed pressure-induced shifts in vibrational modes associated with P–P bonds (A 1 g , A 2 g , ${B}_{2g}$), As–As bonds (A 1 g , A 2 g , ${{B}}_{2g}$), and As–P bonds in b-As x P 1–x alloys. Two distinct pressure regimes were observed. In the first regime (region I), all vibrational modes exhibited a monotonic upshift, indicating phonon hardening due to hydrostatic pressure. In the second regime (region II), As 0.4 P 0.6 and As 0.6 P 0.4 alloys displayed a linear blueshift (or negligible change in some modes) at a reduced rate, suggesting local structural reorganization with less compression on the bonds. Notably, the alloy with the highest As concentration, As 0.8 P 0.2 , exhibited anomalous behavior in the second pressure regime, with a downward shift observed in all As–As and As–P Raman modes (and some P–P modes). Interestingly, the emergence of new peaks corresponding to the E g mode and A 1g mode of the gray-As phase was observed in this pressure range, indicating compressive strain-induced structural changes. The anomalous change in region II confirms the formation of a new local structure, characterized by elongation of the P–P, As–As, and As–P bonds along the zigzag direction within the b-As x P 1–x phase, possibly near the grain boundary. Additionally, a gray-As phase undergoes compressive structural changes. This study underscores the significance of pressure in inducing structural transformations and exploring novel phases in two-dimensional materials, including b-As x P 1–x alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure effects on high velocity microparticle impacts of copper

Constitutive models can fail to predict high-rate deformation behavior due to their inability to account for microstructural effects. In part, this is because of a dearth of experimental benchmarking data in the high strain-rate, low pressure regime, since many high-rate experiments also probe a region of strong shockwaves, at which point microstructure effects no longer play a primary role. This work uses laser-induced particle impact testing to quantitatively study high velocity impacts of small, rigid alumina microspheres on flat copper substrates with varying amounts of initial cold work in the weak shock regime, but at very high strain rates up to ~10 7 s –1 . Through paired experiments and numerical simulations, this work shows that the initial microstructure condition can have significant influence on dynamical mechanical properties in this range. Specifically, prior work hardening of the copper substrate leads to increased rebounding of the microparticles (i.e., less plastic dissipation in the impact) as well as smaller craters. Each of these experimental measurables can be converted into a strength measure, i.e., the dynamic yield strength or dynamic hardness, respectively, neither of which is well predicted consistently by existing constitutive laws. The general trend of hardening can be captured by such models by incorporating an existing “pre-strain,” suggesting that future calibration of the materials parameters may yield a good fit over a broader range of conditions. Our results emphasize the importance of reporting the microstructural condition in dynamic studies, as well as the necessity of accounting for these factors when formulating and optimizing constitutive models.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Stress-dependent activation entropy in thermally activated cross-slip of dislocations

Cross-slip of screw dislocations in crystalline solids is a stress-driven thermally activated process essential to many phenomena during plastic deformation, including dislocation pattern formation, strain hardening, and dynamic recovery. Molecular dynamics (MD) simulation has played an important role in determining the microscopic mechanisms of cross-slip. However, due to its limited timescale, MD can only predict cross-slip rates in high-stress or high-temperature conditions. The transition state theory can predict the cross-slip rate over a broad range of stress and temperature conditions, but its predictions have been found to be several orders of magnitude too low in comparison to MD results. This discrepancy can be expressed as an anomalously large activation entropy whose physical origin remains unclear. Here, we resolve this discrepancy by showing that the large activation entropy results from anharmonic effects, including thermal softening, thermal expansion, and soft vibrational modes of the dislocation. We expect these anharmonic effects to be significant in a wide range of stress-driven thermally activated processes in solids.

Science & Technology - Other Topics↗
DOE OSTI2022

Phase transformation dynamics guided alloy development for additive manufacturing

Fusion-based additive manufacturing technologies enable the fabrication of geometrically and compositionally complex parts unachievable by conventional manufacturing methods. However, the non-uniform and far-from-equilibrium heating/cooling conditions pose a significant challenge to consistently obtaining desirable phases in the as-printed parts. Here, in this study, we report a martensite stainless steel development guided by phase transformation dynamics revealed by in-situ high-speed, high-energy, high-resolution X-ray diffraction. This developed stainless steel consistently forms desired fully martensitic structure across a wide range of cooling rates (10 2 –10 7 °C/s), which enables direct printing of parts with fully martensitic structure. The as-printed material exhibits a yield strength of 1157 ± 23 MPa, comparable to its wrought counterpart after precipitation-hardening heat-treatment. The as-printed property is attributed to the fully martensitic structure and the fine precipitates formed during the intrinsic heat treatment in additive manufacturing. The phase transformation dynamics guided alloy development strategy demonstrated here opens the path for developing reliable, high-performance alloys specific for additive manufacturing.

17–4 PH stainless steel↗
DOE OSTI2023

Model for the Softening Factor within Stages of Work Hardening

A formulation for a dimensionless coefficient c b is derived that represents a scale of microstructural softening for alloys which follow Kocks-Mecking (K-M) work hardening behavior. The variation of the true plastic strain ε p between the proportional limit σ y and the strength σ u at the instability is determined using the Considère criterion. Parameterization of the model is limited to variables expressly measured within tensile experiments. Further development is now made for the softening factor c bi through the individual and sequential stages 3 and 4 of plastic deformation during K-M work hardening Q behavior. Application is shown for tensile test results of Ti-6Al-4V made by different additively manufactured (AM) processes. It is found that the variation in plastic strain as a function of c bi produces a continuous curve representative of the alloy system. The results of data analysis indicate that Θ o3 and c b3 increase, while Θ o4 and c b4 decrease, as the total plastic strain ε p increases. Furthermore, formulations derived for K-M stages 3 and 4 enable the evaluation of other material parameters such as the activation volume ν* for the onset of plastic deformation. This activation volume is found to be near constant, at a ν*-value of 0.353±0.036 nm 3 as computed using a strain-rate sensitivity of strength exponent m of 0.014, irrespective of the AM method used to produce the Ti-6Al-4V alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Predicting extreme anisotropy and shape variations in impact testing of tantalum single crystals

We report recent Taylor cylinder impact tests carried out for Ta single crystals showed strong variations in dimensional changes for different crystallographic directions aligned with the cylindrical axis. In order to capture the effect of crystallography on the deformation characteristics and final shapes of the impacted cylinders, a single crystal material subroutine is adapted and embedded in the solid mechanics/dynamics Finite Element solver Abaqus to simulate the aforementioned single crystal Ta Taylor impact experiments. Details of the coupled model implementation, and insights on the role played by single crystal anisotropic flow on the deformation behavior across a broad range of strain rates and temperatures for different single crystal orientations are presented and discussed. We demonstrate the predictive capability of the adopted crystal plasticity model to capture the significant role played by crystal orientation-induced anisotropy, as well as strain hardening and adiabatic heating, on the dynamic deformation response of crystalline materials. This re-emphasizes the need of microstructure-aware models to improve the accuracy of simulations for high-consequence engineering design.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Defect And Damage Characterization Of Additively Manufactured Titanium Alloy Ti-5553 Using Traditional Computed Tomography Volume Segmentation And Machine Learning Algorithms

The mechanical response of a component is affected by defects, such as porosity, arising from the laser powder bed fusion (LPBF) fabrication process. Thus, it is important to develop accurate and efficient inspection methods for identifying porosity. In this work, porosity identified in an X-ray computed tomography (XCT) volume of a Ti-5553 coupon was compared to pores identified in a serial sectioned volume that represented the ground truth. The porosity of the XCT scan was identified using contrast-based, ISO-based, and machine learning (ML) methods for segmentation. Large inherent porosity was easy to identify, but the ISO thresholding still struggled due to the intensity gradient resulting from both the beam hardening in XCT and the uneven lighting of the serial sectioning panels. Further, the results show that ML-based methods were better suited for identifying small pores and reducing the amount of false positives. Additionally, high strain-rate impact testing was done on some of the XCT samples as well as post-mortem XCT inspection, and the same suite of segmentation and quantification tools were used to identify the large spallation cavities. The comparison of porosity pre- and post-mortem provides insight on the influence of the LPBF porosity on the formation of spall cavities.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Monitoring accelerated alkali-silica reaction in concrete prisms with petrography and electrical conductivity measurements

We report deterioration of concrete due to alkali-silica reaction (ASR) involves a reaction between alkaline ions in the cement pore solution and non-crystalline silica found in many aggregates. Diagnosing and quantifying deterioration due to ASR in concrete currently requires destructive testing for microscopy examinations. In this paper, electrical conductivity is investigated qualitatively as an alternative non-destructive evaluation (NDE) method of ASR in hardened concrete. The study was performed using an unrestrained set of small concrete prism specimens made with highly reactive small aggregates, and kept in an environmental chamber according to ASTM C1293 standard. In a companion study, destructive petrography and damage rating index (DRI) assessment, and pore solution extraction and analysis were performed on the same set of accelerated ASR specimens. The results show that temporal evolution of nondestructive bulk resistivity is linearly correlated with destructive DRI score.

36 MATERIALS SCIENCE↗