SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Design, development, and evaluation of gimballed system for aligning spacecraft mounted instruments with relative wind
Unwanted gimbal rotation friction torques in gyro wheel bearings due to lubrication viscous friction, ball wedging and contamination
Space shuttle guidance, evaluating performance of strapdown and gimballed systems by nominal and abort trajectories
Computerized step-jump and time-transient dynamic analysis application to gimbal mounted Rayleigh- step gas-lubricated thrust bearing design
Computer program for solving attitude error equations related to gimballed platform is described. Program generates matrix elements of attitude error equations when initial matrices and trigonometric identities have been defined. Program is written for IBM 360 computer.
Skewed alignment of two redundant conventional inertial measuring units permits nonambiguous detection and isolation of hard and soft failures in real time by an airborne computer. Accelerometer outputs and gimbal readouts are monitored periodically, and attitude rate and velocity error vectors are computed from these data. Magnitudes of these vectors provide failure detection, and projection of these error vectors onto the coordinate axes of the two clusters permits isolation. A detailed Monte Carlo simulation of one version of the mechanization as applied to Space Shuttle boost trajectories demonstrates effectiveness down to very low levels of inertial instrument performance failures. The results indicate that worst case overall navigation performance occurs when accelerometer failures are of the order of 20 sigma and gyro failures are about 100 sigma for conventional state-of-the-art IMU instruments.
In 2-SPEED (Two Scissored Pair Ensemble, Explicit Distribution) four single-gimbal control moment gyros (SGCMGs) configured into two scissored pairs are combined with an explicit distribution of angular momentum between pairs to produce a system relatively insensitive to the singularity problems which have plagued other SGCMG concepts. In this system, the singularity surfaces in momentum space degenerate to discrete curves. Further, the system permits a smooth passage through these remaining singularities with, at worst, a temporary delay while momentum redistribution takes place. Finally, CMG-out operation is possible within the full volume of the reduced momentum envelope.
Design and development of six gimballed star trackers for Skylab's Apollo Telescope Mount, which performed successfully on all three manned Skylab missions and accumulated a total usage time of approximately 3,500 hours, is described in terms of configurations, materials and construction, qualification testing, performance, and reliability characteristics. A brief program history and design changes incorporated during the life of the program are also discussed. Extensive drawings, block diagrams, and photographs are provided.
Single-Gimbal Control Moment Gyro (SGCMG) systems have been investigated for attitude control of the Large Space Telescope (LST) and the High Energy Astronomy Observatory (HEAO). However, various proposed steering laws for the SGCMG systems thus far have some defects because of singular states of the system. In this report, a steering law for a roof-type SGCMG system is proposed which is based on a new momentum distribution scheme that makes all the singular states unstable. This momentum distribution scheme is formulated by a treatment of the system as a sampled-data system. From analytical considerations, it is shown that this steering law gives control performance which is satisfactory for practical applications. Results of the preliminary computer simulation entirely support this premise.
Parallel mounting of double-gimbaled control moment gyros (DG CMG) is discussed in terms of simplification of the steering law. The steering law/parallel mounted DG CMG is considered to be a 'CMG kit' applicable to any space vehicle where the need for DG CMG's has been established.
The service propulsion system gimbal actuators of the Apollo command and service module were developed, modified, and qualified between February 1962 and April 1968. The development of these actuators is described as the result of extensive testing, retesting, and modification of the initial design. Successful completion of each mission without anomalies attributable to the actuators indicated that the particular configuration (modification) in use was adequate for the flight profile imposed.
Development of the Precision Attitude Determination System (PADS) focused chiefly on the two-axis gimballed star tracker and electronics design improved from that of Precision Pointing Control System (PPCS), and application of the improved tracker for PADS at geosynchronous altitude. System design, system analysis, software design, and hardware design activities are reported. The system design encompasses the PADS configuration, system performance characteristics, component design summaries, and interface considerations. The PADS design and performance analysis includes error analysis, performance analysis via attitude determination simulation, and star tracker servo design analysis. The design of the star tracker and electronics are discussed. Sensor electronics schematics are included. A detailed characterization of the application software algorithms and computer requirements is provided.
The conceptual design studies of a two axis antenna drive assembly for the TDRSS link communications subsystem for LANDSAT D are presented. The recommended antenna drive assembly is a simple and reliable design substantially similar to the antenna and solar array drives developed and space qualified for programs such as DSCS 2 and FltSatCom. The gimbal design tradeoff is presented, along with drive electronics.
A 3-axis active attitude control system with only one rotating part was developed using a momentum wheel with magnetic gimballing capability as a torque actuator for all three body axes. A brief description of magnetic bearing technology is given. It is concluded that based on this technology an integrated energy storage/attitude control system with one air of counterrotating rings could reduce the complexity and weight of conventional systems.
Magnetic bearings used for the suspension of momentum wheels provide conclusive advantages: the low friction torques and the absence of abrasion allow the realization of lightweight high speed wheels with high angular momentum and energy storage capacity and virtually unlimited lifetime. The use of actively controlled bearings provides a magnetic gimballing capability by applying the external signals to the two servo loops controlling the rotational degrees of freedom. Thus, an attitude control system can be realized by using only one rotating mass for 3-axis active satellite stabilization.
The design considerations of bearing selection, bearing fits, bearing installation, and thermal control are discussed for a gimbal with a high stiffness, low friction torque requirement. Tradeoffs between a quad set of small diameter spread apart or a large diameter bearing pair resulted in a cleaner, lighter, stiffer unit with the latter selection. Bearing fits were designed to eliminate clearances with tolerances of .00127 mm 00005 in) on the bearing shafts and housings. The problems in metrology are discussed and a perferred technique for measurement of small cross-section bearings described. A technique for installation to assure proper seating of the bearing is offered. Where transient thermal conditions are involved, a method of controlling bearing friction by active control of bearing temperature gradients including the use of bearing unload test curves is described.
The need for higher accuracy in pointing systems continues to grow. Fundamental limitations are inherent in the components used for gimbals. This paper discusses some developments which are expected to make it possible to achieve higher accuracy and stability. Ironless armature torque motors are described which exhibit zero hysteresis and no preferred position. Non-contacting signal and power transfer devices to eliminate friction and cable-wrap torques have also been developed. Magnetic bearings can eliminate the last remaining source of erratic frictional effects. Controllers using Kalman estimation techniques can accommodate constant residual effects.
A precision bearing gimbal system designed to allow a spaceborne infrared sensor to stare at points on the Earth while in orbit is described. The problems encountered, analytical tools and test methods used, and data applicable to users of similar systems are presented. Assembly procedures, bearing preload effects, moisture control, structural analysis, and noise control are specifically examined.