Results for “geophysical forecasting” — Page 7

NASA NTRS2000

Sensitivity of Spacebased Microwave Radiometer Observations to Ocean Surface Evaporation

Ocean surface evaporation and the latent heat it carries are the major components of the hydrologic and thermal forcing on the global oceans. However, there is practically no direct in situ measurements. Evaporation estimated from bulk parameterization methods depends on the quality and distribution of volunteer-ship reports which are far less than satisfactory. The only way to monitor evaporation with sufficient temporal and spatial resolutions to study global environment changes is by spaceborne sensors. The estimation of seasonal-to-interannual variation of ocean evaporation, using spacebased measurements of wind speed, sea surface temperature (SST), and integrated water vapor, through bulk parameterization method,s was achieved with reasonable success over most of the global ocean, in the past decade. Because all the three geophysical parameters can be retrieved from the radiance at the frequencies measured by the Scanning Multichannel Microwave Radiometer (SMMR) on Nimbus-7, the feasibility of retrieving evaporation directly from the measured radiance was suggested and demonstrated using coincident brightness temperatures observed by SMMR and latent heat flux computed from ship data, in the monthly time scale. However, the operational microwave radiometers that followed SMMR, the Special Sensor Microwave/Imager (SSM/I), lack the low frequency channels which are sensitive to SST. This low frequency channels are again included in the microwave imager (TMI) of the recently launched Tropical Rain Measuring Mission (TRMM). The radiance at the frequencies observed by both TMI and SSM/I were simulated through an atmospheric radiative transfer model using ocean surface parameters and atmospheric temperature and humidity profiles produced by the reanalysis of the European Center for Medium Range Weather Forecast (ECMWF). From the same ECMWF data set, coincident evaporation is computed using a surface layer turbulent transfer model. The sensitivity of the radiance to evaporation over various seasons and geographic locations are examined. The microwave frequencies with radiance that are significant correlated with evaporation are identify and capability of estimating evaporation directly from TMI will be discussed.

Liu, Timothy W.↗

DOE OSTI2025

Towards provision of regularly updated climate data from the Coupled Model Intercomparison Project

The Coupled Model Intercomparison Project (CMIP) is a flagship of the World Climate Research Programme (WCRP). CMIP has become a recognised ‘brand’ in climate circles evolving over the last thirty years from a targeted research activity by a small number of climate modelling centres intercomparing their Earth System Model (ESM) simulations to a broad international coordinated research effort (Durack et al, 2025). CMIP is organized as a research activity leveraging funded and in-kind contributions from experts within modelling centres and the broader scientific community supported more recently by a fully-funded International Project Office. Within CMIP, Model Intercomparison Projects (MIPs) are community-designed to understand past, present and future climate. CMIP data provides a valuable resource for climate research and is routinely used to assess model representation of climate processes and test scientific hypotheses in the context of model uncertainty and (forced and internal) variability as evident from its prolific use in scientific publications1 . The impact relies on enabling infrastructure (most prominently via the Earth System Grid Federation (ESGF)), which allows sharing of simulation output, provision of the boundary conditions used in each simulation, and definition of the data standards that are essential to facilitating wide use of the data. The impact is supplemented by the wide-ranging scrutiny to which model simulations are subjected. Beyond its use in research, CMIP data is a key resource for communities producing derived climate information from downscaling and impact studies, such as the Coordinated Regional Downscaling Experiment (CORDEX; Gutowski et al., 2016) and the Intersectoral Impacts MIP (ISIMIP; Frieler et al., 2024). Government, academic and commercial entities also increasingly rely on CMIP and its downstream data for climate risk assessments and climate services (for example, Copernicus Climate Change Service and World Bank portal). This means that, although CMIP is a research activity, it increasingly serves a secondary and very relevant role as a provider of climate data – a long-recognised dichotomy (Stevens, 2024). Research and applications have distinct needs, with the former requiring flexibility and generality and the latter consistency. Here we explain how the design of the research activity has been adapted to reduce the burdens imposed by applications and how the research infrastructure might evolve to further enable scientific inquiry. We propose one possible approach to consistently providing model information and projections for applications in the future.

Environmental sciences↗

DOE OSTI2020

US East Coast synthetic aperture radar wind atlas for offshore wind energy

We present the first synthetic aperture radar (SAR) offshore wind atlas of the US East Coast from Georgia to the Canadian border. Images from RADARSAT-1, Envisat, and Sentinel-1A/B are processed to wind maps using the geophysical model function (GMF) CMOD5.N. Extensive comparisons with 6008 collocated buoy observations of the wind speed reveal that biases of the individual systems range from -0.8 to 0.6 m s -1 . Unbiased wind retrievals are crucial for producing an accurate wind atlas, and intercalibration of the SAR observations is therefore applied. Wind retrievals from the intercalibrated SAR observations show biases in the range of to -0.2 to 0.0 m s -1 , while at the same time improving the root-mean-squared error from 1.67 to 1.46 m s -1 . The intercalibrated SAR observations are, for the first time, aggregated to create a wind atlas at the height 10 m a.s.l. (above sea level). The SAR wind atlas is used as a reference to study wind resources derived from the Wind Integration National Dataset Toolkit (WTK), which is based on 7 years of modelling output from the Weather Research and Forecasting (WRF) model. Comparisons focus on the spatial variation in wind resources and show that model outputs lead to lower coastal wind speed gradients than those derived from SAR. Areas designated for offshore wind development by the Bureau of Ocean Energy Management are investigated in more detail; the wind resources in terms of the mean wind speed show spatial variations within each designated area between 0.3 and 0.5 m s -1 for SAR and less than 0.2m s -1 for the WTK. Our findings indicate that wind speed gradients and variations might be underestimated in mesoscale model outputs along the US East Coast.

17 WIND ENERGY↗

DOE OSTI2024

Physics informed neural network can retrieve rate and state friction parameters from acoustic monitoring of laboratory stick-slip experiments

Various machine learning (ML) and deep learning (DL) techniques have been recently applied to the forecasting of laboratory earthquakes from friction experiments. The magnitude and timing of shear failures in stick-slip cycles are predicted using features extracted from the recorded ultrasonic or acoustic emission (AE) signals. In addition, the Rate and State Friction (RSF) constitutive laws are extensively used to model the frictional behavior of faults. In this work, we use data from shear experiments coupled with passive acoustic (variance, kurtosis, and AE rate) interleaved with active source ultrasonic monitoring (transmitted wave amplitude) to develop physics-informed neural network (PINN) models incorporating the RSF law and AE rate generation equation with wave amplitude serving as a proxy for friction state variable. This PINN framework allows learning RSF parameters from stick-slip experiments rather than measuring them through a series of velocity step experiments. We observe that when the stick-slip cycles are irregular, the PINN models outperform the data-driven DL models. Transfer learning (TL) PINN models are also developed by pre-training on data collected at one normal stress level followed by forecasting shear failures and retrieving RSF parameters at other stress levels (i.e., with different recurrence intervals) after retraining on a limited amount of new data. Our findings suggest that TL models perform better compared to standalone models. Both standalone and TL PINN-estimated RSF parameters and their ground truth values show excellent agreements thus demonstrating that RSF parameters can be retrieved from laboratory stick-slip experiments using the corresponding acoustic data and that the transmitted wave amplitude provides a good representation of the evolving frictional state during stick-slips.

58 GEOSCIENCES↗

NASA NTRSDate not supplied

Enhancing Radiative Transfer Models for Optimized Assimilation of Microwave and Radar Observations

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRSDate not supplied

Optimizing Assimilation of Microwave and Radar Observations in the NWP Models

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRSDate not supplied

Assimilation of Spaceborne Microwave and Radar Observations

Radiative transfer models are extensively used for the assimilation of satellite observations into NWP models as well as retrieving geophysical products from satellite measurements. The Community Radiative Transfer Model (CRTM) is a community model developed by NOAA JCSDA and widely used for different purposes requiring RT calculations. CRTM requires bulk optical properties of hydrometeors in the form of lookup tables in order to perform all-sky RT calculations. However, the current cloud scattering lookup tables in CRTM assume spherical shapes for all frozen hydrometeors, whereas actual clouds contain frozen particles with diverse shapes. The first part of this talk presents the implementation and validation of a comprehensive Discrete Dipole Approximation (DDA) cloud scattering database into CRTM, specifically targeting microwave frequencies. The DDA technique proves effective in simulating the optical properties of non-spherical hydrometeors in the microwave region. The original DDA database assumes total random orientation in calculating single scattering properties. To generate the required mass scattering parameters for CRTM, the single scattering properties and water content dependent particle size distributions are used. The evaluation of results involved a collocated dataset comprising short-term forecasts from the Integrated Forecast System of the European Center for Medium-Range Weather Forecasts and satellite microwave data. The findings demonstrate that the DDA lookup tables significantly reduce discrepancies between simulated and observed values when compared to the Mie tables. Passive instruments lack the ability to provide vertically resolved measurements of clouds and precipitation, which can be obtained by active radar instruments. However, incorporating these active measurements into data assimilation systems presents challenges due to the absence of fast forward radiative transfer models and difficulties in error modeling. The second part of the talk focuses on the development, evaluation, and sensitivity analysis of a forward radar model integrated into CRTM. The forward radar model utilizes scattering properties obtained from hydrometeor lookup tables generated using the discrete dipole approximation. By utilizing CRTM instrument-specific coefficients, the model can calculate both reflectivity and attenuated reflectivity for any given radar instrument and zenith angles. Evaluation using CloudSat measurements demonstrates a strong agreement between simulations and observations when the input profiles of hydrometeors align with the measured reflectivity profiles.

Isaac Moradi↗

NASA NTRS2001

Physical Processes Governing Atmospheric Trace Constituents Measured from an Aircraft on PEM-Tropics

Before the mission, the PI (principal investigator) was instrumental in securing real-time use of the new 51-level ECMWF (European Centre for Medium Range Weather Forecasts) meteorological data. During the mission, he provided flight planning and execution guidance as meteorologist for the P-3B. Mr. Yong Zhu computed and plotted meteorological forecast maps using the ECMWF data and transmitted them to the field from MIT (Massachusetts Institute of Technology). Dr. John Cho was in the field for the Christmas Island portion to extract data from the on-site NOAA (National Oceanic and Atmospheric Administration) radars for local wind profiles that were used at the flight planning meetings. When the power supply for the VHF radar failed, he assisted the NOAA engineer in its repair. After the mission, Mr. Zhu produced meteorological data memos, which were made available to the PEM (Pacific Exploratory Mission)-Tropics B science team on request. An undergraduate student, Ms. Danielle Morse, wrote memos annotating the cloud conditions seen on the aircraft external monitor video tapes. Dr. Cho and the PI circulated a memo regarding the status (and associated problems) of the meteorological measurement systems on the DC-8 and P-3B to the relevant people on the science team. Several papers by members of our project were completed and accepted by JGR (Journal of Geophysical Research) for the first special section on PEM-Tropics B. These papers included coverage of the following topics: 1) examination of boundary layer data; 2) water vapor transport; 3) tropospheric trace constituent layers; 4) summarizations of the meteorological background and events during PEM-Tropics B; 5) concomitant lidar measurements of ozone, water vapor, and aerosol.

Newell, Reginald E.↗

DOE OSTI2021

Regional Subsidence Analysis Through a Multi-Scale Modeling Framework Based on Breakage Mechanics

Although poroelastic models are often used to explain the delay between subsurface fluid depletion and ground subsidence, inelastic compaction involving permanent changes of rock microstructure may exacerbate hydro-mechanical coupling, thus influencing the interpretation of measurements and long-term forecasts. Here, a multi-scale modeling approach is discussed, which accounts for the inherent connection between rock microstructure, hydraulic conductivity, and pore compaction. A constitutive model built within the framework of breakage mechanics is proposed to link the hydraulic conductivity of granular rocks with inelastic deformations and changes in grading caused by injection-depletion cycles at stress levels far from yielding. The proposed model has been incorporated into large-scale simulation frameworks, thus enabling the spatiotemporal mapping of regional subsidence through a hybrid, semi-analytical approach. Numerical results based on this strategy show that the model allows isolating near-field and far-field effects into the computation of land subsidence and can generate forecasts for different modeling scenarios (e.g., elastic and inelastic compaction, constant permeability, and concurrent change of compressibility and permeability). In particular, examples of simulations for the case of the Groningen gas field are discussed, showing the model capabilities to use both field measurements and laboratory tests for the generation of reasonable subsidence maps, without expensive computational costs. Results indicate that ignoring coupled inelastic effects has major consequences on the predicted timescale of subsidence. Specifically, while all the model scenarios produced similar long-term ground settlements, those ignoring breakage-dependent permeability changes result in a variation of the temporal window of residual subsidence of the order of several decades.

58 GEOSCIENCES↗

NASA NTRS2020

Assimilation of satellite microwave observations over the rainbands of tropical cyclones

A novel Bayesian Monte Carlo integration (BMCI) technique was developed to retrieve geophysical variables from satellite microwave radiometer data in the presence of tropical cyclones. The BMCI technique includes three steps: generating a stochastic database, simulating satellite brightness temperatures using a radiative transfer model, and retrieving geophysical variables such as profiles of temperature, relative humidity, and cloud liquid and ice water content from real observations. The technique also provides uncertainty estimates for each retrieval and can output the error covariance matrix of selected parameters. The measurements from the Advanced Technology Microwave Sounder (ATMS) on board Suomi National Polar-Orbiting Partnership (Suomi NPP) and the Global Precipitation Measurement (GPM) Microwave Imager (GMI) were used as input. A new technique was developed to correct the ATMS and GMI observations for the beam-filling effect, which is due to small-scale variability of precipitation and clouds when compared with the instrument footprint and also the nonlinear relation between the brightness temperature and precipitation. In addition, the assimilation of the BMCI retrievals into the NASA GEOS model is discussed for Hurricane Maria. The results show that assimilating the BMCI retrievals can influence the dynamical features of the cyclone, including a stronger warm core, a symmetric eye, and vertically aligned wind columns. Two possible factors that may limit the impact of the BMCI retrievals include 1) the resolution of the model (about 25 km), which was too coarse to show the potential of the BMCI data in improving the representation of tropical storms in the model forecast, and 2) the data assimilation system not being able to consider vertically correlated observation errors.

Isaac Moradi↗

DOE OSTI2021

Data Arrays for Microearthquake (MEQ) Monitoring using Deep Learning for the Newberry EGS Sites

The 'Machine Learning Approaches to Predicting Induced Seismicity and Imaging Geothermal Reservoir Properties' project looks to apply machine learning (ML) methods to Microearthquake (MEQ) data for imaging geothermal reservoir properties and forecasting seismic events, in order to advance geothermal exploration and safe geothermal energy production. As part of the project, this submission provides data arrays for 149 microearthquakes between the year 2012 and 2013 at the Newberry EGS Site for use with the Deep Learning Algorithm that has been developed. The data provided includes raw waveform data, location data, normalized waveform data, and processed waveform data. Penn State Geothermal Team has shared the following files from the project: - 149 microearthquakes (MEQs) between 2012 and 2013 at Newberry EGS sites, 'Normalized Waveform Inputs.npz' are normalized waveforms. - labels of 149 MEQs: Processed Waveform Inputs.npz - location labels of 149 MEQs: Location Data.npz Note: .npz is the python file format by NumPy that provides storage of array data.

15 GEOTHERMAL ENERGY↗

DOE OSTI2024

Merged Observatory Data Files (MODFs): an integrated observational data product supporting process-oriented investigations and diagnostics

A large and ever-growing body of geophysical information is measured in campaigns and at specialized observatories as a part of scientific expeditions and experiments. These collections of observed data include many essential climate variables (as defined by the Global Climate Observing System) but are often distinguished by a wide range of additional non-routine measurements that are designed to not only document the state of the environment but also the drivers that contribute to that state. These field data are used not only to further understand environmental processes through observation-based studies but also to provide baseline data to test model performance and to codify understanding to improve predictive capabilities. To address the considerable barriers and difficulty in utilizing these diverse and complex data for observation–model research, the Merged Observatory Data File (MODF) concept has been developed. A MODF combines measurements from multiple instruments into a single file that complies with well-established data format and metadata practices and has been designed to parallel the development of corresponding Merged Model Data Files (MMDFs). Using the MODF and MMDF protocols will facilitate the evolution of model intercomparison projects into model intercomparison and improvement projects by putting observation and model data “on the same page” in a timely manner. The MODF concept was developed especially for weather forecast model studies in the Arctic. The surprisingly complex process of implementing MODFs in that context refined the concept itself. Thus, this article explains the concept of MODFs by providing details on the issues that were revealed and resolved during that first specific implementation. Detailed instructions are provided on how to make MODFs, and this article can be considered a MODF creation manual.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Earth's Energy Imbalance More Than Doubled in Recent Decades

Abstract Global warming results from anthropogenic greenhouse gas emissions which upset the delicate balance between the incoming sunlight, and the reflected and emitted radiation from Earth. The imbalance leads to energy accumulation in the atmosphere, oceans and land, and melting of the cryosphere, resulting in increasing temperatures, rising sea levels, and more extreme weather around the globe. Despite the fundamental role of the energy imbalance in regulating the climate system, as known to humanity for more than two centuries, our capacity to observe it is rapidly deteriorating as satellites are being decommissioned.

Mauritsen, Thorsten [Department of Meteorology and↗

DOE OSTI2022

DeepShake: Shaking Intensity Prediction Using Deep Spatiotemporal RNNs for Earthquake Early Warning

Abstract We propose a deep spatiotemporal recurrent neural network, DeepShake, to project future shaking intensity directly from current ground-motion observations. DeepShake is a network-based forecasting model, able to predict future shaking intensity at all stations within a network given previously measured ground shaking. The model is not given any a priori knowledge of station locations; instead, it learns wave propagation amplitudes and delays solely from training data. We developed DeepShake with the 35,679 earthquakes from the 2019 Ridgecrest sequence. Tasked with alerting for modified Mercalli intensity (MMI) IV+ shaking on 3568 validation earthquakes at least 5 s in advance, DeepShake achieves an equal error rate of 11.4%. For the Mw 7.1 earthquake that hit Ridgecrest on 5 July 2019, DeepShake was able to provide targeted alerts to all stations inside the network 5 s prior to the arrival of MMI IV+ waveforms. DeepShake demonstrates that deep spatiotemporal neural networks can effectively provide one-step earthquake early warning with reasonable accuracy and latency.

Geochemistry & Geophysics↗

DOE OSTI2023

Classification Analysis of Southwest Pacific Tropical Cyclone Intensity Changes Prior to Landfall

This study evaluates the ability of a random forest classifier to identify tropical cyclone (TC) intensification or weakening prior to landfall over the western region of the Southwest Pacific Ocean (SWPO) basin. For both Australia mainland and SWPO island cases, when a TC first crosses land after spending ≥24 h over the ocean, the closest hour prior to the intersection is considered as the landfall hour. If the maximum wind speed (V max ) at the landfall hour increased or remained the same from the 24-h mark prior to landfall, the TC is labeled as intensifying and if the V max at the landfall hour decreases, the TC is labeled as weakening. Geophysical and aerosol variables closest to the 24 h before landfall hour were collected for each sample. The random forest model with leave-one-out cross validation and the random oversampling example technique was identified as the best-performing classifier for both mainland and island cases. The model identified longitude, initial intensity, and sea skin temperature as the most important variables for the mainland and island landfall classification decisions. Incorrectly classified cases from the test data were analyzed by sorting the cases by their initial intensity hour, landfall hour, monthly distribution, and 24-h intensity changes. TC intensity changes near land strongly impact coastal preparations such as wind damage and flood damage mitigations; hence, this study will contribute to improve identifying and prioritizing prediction of important variables contributing to TC intensity change before landfall.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Rapid wavefield forecasting for earthquake early warning via deep sequence to sequence learning

We propose a deep learning model, WaveCastNet, to forecast high-dimensional wavefields. WaveCastNet integrates a convolutional long expressive memory architecture into a sequence-to-sequence forecasting framework, enabling it to model long-term dependencies and multiscale patterns in both space and time. By sharing weights across spatial and temporal dimensions, WaveCastNet requires significantly fewer parameters than more resource-intensive models such as transformers, resulting in faster inference times. Crucially, WaveCastNet also generalizes better than transformers to rare and critical seismic scenarios, such as high-magnitude earthquakes. Here, we show the ability of the model to predict the intensity and timing of destructive ground motions in real time, using simulated data from the San Francisco Bay Area. Furthermore, we demonstrate its zero-shot capabilities by evaluating WaveCastNet on real earthquake data. Our approach does not require estimating earthquake magnitudes and epicenters, steps that are prone to error in conventional methods, nor does it rely on empirical ground-motion models, which often fail to capture strongly heterogeneous wave propagation effects.

Geophysics↗

DOE OSTI2023

Foreshock properties illuminate nucleation processes of slow and fast laboratory earthquakes

Understanding the connection between seismic activity and the earthquake nucleation process is a fundamental goal in earthquake seismology with important implications for earthquake early warning systems and forecasting. We use high-resolution acoustic emission (AE) waveform measurements from laboratory stick-slip experiments that span a spectrum of slow to fast slip rates to probe spatiotemporal properties of laboratory foreshocks and nucleation processes. We measure waveform similarity and pairwise differential travel-times (DTT) between AEs throughout the seismic cycle. AEs broadcasted prior to slow labquakes have small DTT and high waveform similarity relative to fast labquakes. We show that during slow stick-slip, the fault never fully locks, and waveform similarity and pairwise differential travel times do not evolve throughout the seismic cycle. In contrast, fast laboratory earthquakes are preceded by a rapid increase in waveform similarity late in the seismic cycle and a reduction in differential travel times, indicating that AEs begin to coalesce as the fault slip velocity increases leading up to failure. These observations point to key differences in the nucleation process of slow and fast labquakes and suggest that the spatiotemporal evolution of laboratory foreshocks is linked to fault slip velocity.

58 GEOSCIENCES↗

NASA NTRS2011

The NASA Soil Moisture Active Passive (SMAP) Mission - Algorithm and Cal/Val Activities and Synergies with SMOS and Other L-Band Missions

NASA's Soil Moisture Active Passive (SMAP) mission, planned for launch in late 2014, has as its key measurement objective the frequent, global mapping of near-surface soil moisture and its freeze-thaw state. SMAP soil moisture and freeze/thaw measurements at 10 km and 3 km resolutions respectively, would enable significantly improved estimates of water, energy and carbon transfers between the land and atmosphere. Soil moisture control of these fluxes is a key factor in the performance of atmospheric models used for weather forecasts and climate projections Soil moisture measurements are also of great importance in assessing floods and for monitoring drought. In addition, observations of soil moisture and freeze/thaw timing over the boreal latitudes can help reduce uncertainties in quantifying the global carbon balance. The SMAP measurement concept utilizes an L-band radar and radiometer sharing a rotating 6-meter mesh reflector antenna. The SMAP radiometer and radar flight hardware and ground processing designs are incorporating approaches to identify and mitigate potential terrestrial radio frequency interference (RFI). The radar and radiometer instruments are planned to operate in a 680 km polar orbit, viewing the surface at a constant 40-degree incidence angle with a 1000-km swath width, providing 3-day global coverage. Data from the instruments would yield global maps of soil moisture and freeze/thaw state to be provided at 10 km and 3 km resolutions respectively, every two to three days. Plans are to provide also a radiometer-only soil moisture product at 40-km spatial resolution. This product and the underlying brightness temperatures have characteristics similar to those provided by the Soil Moisture and Ocean Salinity (SMOS) mission. As a result, there are unique opportunities for common data product development and continuity between the two missions. SMAP also has commonalities with other satellite missions having L-band radiometer and/or radar sensors applicable to soil moisture measurement, such as Aquarius, SAO COM, and ALOS-2. The algorithms and data products for SMAP are being developed in the SMAP Science Data System (SDS) Testbed. The algorithms are developed and evaluated in the SDS Testbed using simulated SMAP observations as well as observational data from current airborne and spaceborne L-band sensors including SMOS. The SMAP project is developing a Calibration and Validation (Cal/Val) Plan that is designed to support algorithm development (pre-launch) and data product validation (post-launch). A key component of the Cal/Val Plan is the identification, characterization, and instrumentation of sites that can be used to calibrate and validate the sensor data (Level I) and derived geophysical products (Level 2 and higher). In this presentation we report on the development status of the SMAP data product algorithms, and the planning and implementation of the SMAP Cal/Val program. Several components of the SMAP algorithm development and Cal/Val plans have commonality with those of SMOS, and for this reason there are shared activities and resources that can be utilized between the missions, including in situ networks, ancillary data sets, and long-term monitoring sites.

Njoku, Eni↗