Results for “fluid properties” — Page 7

NASA NTRS1972

Choked flow of fluid nitrogen with emphasis on the thermodynamic critical region.

Results of experimental measurements of critical flow rate and pressure ratio for nitrogen flowing through a nozzle. Data for selected stagnation isotherms from 87.5 to 234 K with pressures to 9.3 MN/sq m are compared to an equilibrium model with real fluid properties and also a nonequilibrium model. Critical flow pressure ratio along an isotherm tends to peak while the flow rate indicates an inflection. The point is closely associated with the transposed critical temperature and represents a change in the fluid structure.

Hendricks, R. C.↗

NASA NTRS1990

Rate correlation for condensation of pure vapor on turbulent, subcooled liquid

An empirical correlation is presented for the condensation of pure vapor on a subcooled, turbulent liquid with a shear-free interface. The correlation expresses the dependence of the condensation rate on fluid properties, on the liquid-side turbulence (which is imposed from below), and on the effects of buoyancy in the interfacial thermal layer. The correlation is derived from experiments with steam and water, but under conditions which simulate typical cryogenic fluids.

Brown, J. Steven↗

NASA NTRS2003

Scaling of Two-Phase Flows to Partial-Earth Gravity

A report presents a method of scaling, to partial-Earth gravity, of parameters that describe pressure drops and other characteristics of two-phase (liquid/ vapor) flows. The development of the method was prompted by the need for a means of designing two-phase flow systems to operate on the Moon and on Mars, using fluid-properties and flow data from terrestrial two-phase-flow experiments, thus eliminating the need for partial-gravity testing. The report presents an explicit procedure for designing an Earth-based test bed that can provide hydrodynamic similarity with two-phase fluids flowing in partial-gravity systems. The procedure does not require prior knowledge of the flow regime (i.e., the spatial orientation of the phases). The method also provides for determination of pressure drops in two-phase partial-gravity flows by use of a generalization of the classical Moody chart (previously applicable to single-phase flow only). The report presents experimental data from Mars- and Moon-activity experiments that appear to demonstrate the validity of this method.

Hurlbert, Kathryn M.↗

DOE OSTI2026

A Space-Time Fluid (Unabridged)

Purpose: This essay is a retelling of general relativity in a language in which space-time geometry is expressed as a fluid. This trivial and useful reformulation gives 1) a non-perturbative covariant description of cosmological inhomogeneities and 2) a simple formula describing how cosmic inhomogeneities are generated on super-horizon scales. Methods: Equating the Ricci curvature with the associated matter stress-energy gives a description of space-time geometry in terms of fluid properties. These locally measurable (covariant) non-perturbative quantities are in some ways superior to commonly used "gauge invariant" quantities. The dynamics of a quantity (kurvature) which describes cosmological inhomogeneities is described in detail. A detailed comparison is made of space-time fluid dynamics with that of a classical (Newtonian physics) fluid. Results: The fluid lexicon permits an unambiguous definition of the velocity of space-time. The evolution of the space-time fluid is in many ways identical with that of the classical fluid when expressed in Lagrangian coordinates. Kurvature is a measure of the specific binding energy of the fluid and is a most useful covariant measure of cosmological inhomogeneities. For plausible matter models kurvature will increase, even on super-horizon scales, due to non-linear hydrodynamic effects rather than gravity. This phenomena is also exhibited by classical fluids. Conclusion: The space-time fluid representation of geometrodynamics gives a simple and useful description of the evolution of cosmological inhomogeneities.

Stebbins, Albert [Fermilab] (ORCID:000000023807725↗

NASA NTRSDate not supplied

CFD Model Development of a Cryogenic Storage Tank Self-Pressurization in Normal Gravity and Validation against SHIIVER Experiment

Two-Phase flow and heat transfer simulations with interfacial phase change of the Structural Heat Intercept, Insulation, and Vibration Evaluation Rig (SHIIVER) self-pressurization experiment were conducted using storage tank CFD model in the framework of the ANSYS Fluent CFD code. The simulations were performed for the 70% fill level case with MLI on domes and no vapor cooling. All the phase change calculations in these simulations were generated by in-house Schrage-based evaporation-condensation model. The calculations were performed using both the VOF and Sharp Interface multiphase 2Daxisymmetric models. A number of parametric and sensitivity studies were performed to check the various aspects of the CFD model. These studies helped to understand the effects of varying several parameters on the tank pressure and temperature during self-pressurization. These parameters include: the effect of turbulence modeling and turbulence damping at the interface; the effect of constant vs. temperature dependent fluid properties; the effect of accommodation coefficient; the effect of modeling phase change at the interface and the effect of the fill level.

Computational Fluid Dynamics↗

NASA NTRS2001

CFD Simulation of Liquid Rocket Engine Injectors

Detailed design issues associated with liquid rocket engine injectors and combustion chamber operation require CFD methodology which simulates highly three-dimensional, turbulent, vaporizing, and combusting flows. The primary utility of such simulations involves predicting multi-dimensional effects caused by specific injector configurations. SECA, Inc. and Engineering Sciences, Inc. have been developing appropriate computational methodology for NASA/MSFC for the past decade. CFD tools and computers have improved dramatically during this time period; however, the physical submodels used in these analyses must still remain relatively simple in order to produce useful results. Simulations of clustered coaxial and impinger injector elements for hydrogen and hydrocarbon fuels, which account for real fluid properties, is the immediate goal of this research. The spray combustion codes are based on the FDNS CFD code' and are structured to represent homogeneous and heterogeneous spray combustion. The homogeneous spray model treats the flow as a continuum of multi-phase, multicomponent fluids which move without thermal or velocity lags between the phases. Two heterogeneous models were developed: (1) a volume-of-fluid (VOF) model which represents the liquid core of coaxial or impinger jets and their atomization and vaporization, and (2) a Blob model which represents the injected streams as a cloud of droplets the size of the injector orifice which subsequently exhibit particle interaction, vaporization, and combustion. All of these spray models are computationally intensive, but this is unavoidable to accurately account for the complex physics and combustion which is to be predicted, Work is currently in progress to parallelize these codes to improve their computational efficiency. These spray combustion codes were used to simulate the three test cases which are the subject of the 2nd International Workshop on-Rocket Combustion Modeling. Such test cases are considered by these investigators to be very valuable for code validation because combustion kinetics, turbulence models and atomization models based on low pressure experiments of hydrogen air combustion do not adequately verify analytical or CFD submodels which are necessary to simulate rocket engine combustion. We wish to emphasize that the simulations which we prepared for this meeting are meant to test the accuracy of the approximations used in our general purpose spray combustion models, rather than represent a definitive analysis of each of the experiments which were conducted. Our goal is to accurately predict local temperatures and mixture ratios in rocket engines; hence predicting individual experiments is used only for code validation. To replace the conventional JANNAF standard axisymmetric finite-rate (TDK) computer code 2 for performance prediction with CFD cases, such codes must posses two features. Firstly, they must be as easy to use and of comparable run times for conventional performance predictions. Secondly, they must provide more detailed predictions of the flowfields near the injector face. Specifically, they must accurately predict the convective mixing of injected liquid propellants in terms of the injector element configurations.

Farmer, Richard↗

NASA NTRSDate not supplied

Comparison of Convective Heat Transfer Correlations and Their Application to Nuclear Thermal Propulsion Reactors

This study analyzes various Nusselt number and friction factor correlations and applies them to a Small Nuclear Rocket Engine model with a Sinusoidal power distribution profile to understand their effects on the temperatures and pressures inside the reactor. A nodal thermal hydraulic solver was used to determine the fluid and channel surface temperatures while also incorporating variable fluid properties and channel roughness. The results showed that the considered friction factors could essentially be used interchangeably given that their difference affected the pressure by less than 1%. However, large variations in the tube surface temperature were obtained for the different Nusselt numbers while the fluid temperature distribution was forced to remain the same. Supersonic flow conditions presented by Maynard Taylor are investigated to serve as a baseline for how experimental errors can lead to uncertainties in the reported empirical correlations. Detailed experimental investigation is necessary to determine the Nusselt number correlation that will provide the best prediction of the thermal hydraulic performance inside the reactor fluid flow channels.

Experiment↗

NASA NTRSDate not supplied

Comparison of Convective Heat Transfer Correlations and Their Application to NTP Reactors

This study analyzes various Nusselt number and friction factor correlations and applies them to a Small Nuclear Rocket Engine model with a Sinusoidal power distribution profile to understand their effects on the temperatures and pressures inside the reactor. A nodal thermal hydraulic solver was used to determine the fluid and channel surface temperatures while also incorporating variable fluid properties and channel roughness. The results showed that the considered friction factors could essentially be used interchangeably given that their difference affected the pressure by less than 1%. However, large variations in the tube surface temperature were obtained for the different Nusselt numbers while the fluid temperature distribution was forced to remain the same. Supersonic flow conditions presented by Maynard Taylor are investigated to serve as a baseline for how experimental errors can lead to uncertainties in the reported empirical correlations. Detailed experimental investigation is necessary to determine the Nusselt number correlation that will provide the best prediction of the thermal hydraulic performance inside the reactor fluid flow channels.

Nuclear Thermal Propulsion↗

NASA NTRS1990

Study of two-phase flow in helical and spiral coils

The principal purposes of the present study were to: (1) observe and develop a fundamental understanding of the flow regimes and their transitions occurring in helical and spiral coils; and (2) obtain pressure drop measurements of such flows, and, if possible, develop a method for predicting pressure drop in these flow geometries. Elaborating upon the above, the general intent is to develop criteria (preferably generalized) for establishing the nature of the flow dynamics (e.g. flow patterns) and the magnitude of the pressure drop in such configurations over a range of flow rates and fluid properties. Additionally, the visualization and identification of flow patterns were a fundamental objective of the study. From a practical standpoint, the conditions under which an annular flow pattern exists is of particular practical importance. In the possible practical applications which would implement these geometries, the working fluids are likely to be refrigerant fluids. In the present study the working fluids were an air-water mixture, and refrigerant 113 (R-113). In order to obtain records of flow patterns and their transitions, video photography was employed extensively. Pressure drop measurements were made using pressure differential transducers connected across pressure taps in lines immediately preceding and following the various test sections.

Keshock, Edward G.↗

NASA NTRSDate not supplied

Surface Instability of Liquid Propellants in Microgravity During Pulsed Settling Operations

Pulsing reaction control system (RCS) thrusters, vent valves, or other propulsion devices can preserve propellant resources in space, but this operation also effectively introduces a vibration to the vehicle. When the vibration is perpendicular to the liquid propellant surface, Faraday waves may be generated at the liquid-vapor interface. These Faraday instabilities can perturb or break up the liquid surface of cryogenic tanks, leading to inefficiencies in thermal management or even ullage collapse. Drawing from theory and experiments, an engineering model defining the allowable design regions for pulsed settling in microgravity was assembled and verified with computational fluid dynamics (CFD) simulations. A traditional settling metric, the Bond number, was also overlaid in the model to indicate which duty cycles were insufficient to overcome surface tension and aggregate propellant. Mission planners and engineers can consult the tool to rapidly evaluate the stability of a liquid-vapor interface given the pulse frequency and the excitation acceleration. Expressions developed for Faraday waves induced by a sinusoidal forcing input at standard gravity were found to provide excellent predictive capabilities for pulsed, or rectangular, waveforms in the absence of a consistent gravitational acceleration. This study extends the usage of these equations to an alternative forcing function and microgravity environments for the purpose of estimating natural frequencies, surface mode shapes, surface wave amplitudes, and the onset of droplet ejection. CFD simulations with the Loci/STREAM-VoF (Volume of Fluid) solver were initially validated against experimental results in standard gravity. Discrete points on the design map were then investigated with CFD and confirmed that the engineering model reliably indicates surface stability and most Faraday wave characteristics without requiring higher-fidelity tools. The engineering model is highly extensible and can be adapted for various propellant fill fractions, fluid properties, and tank sizes.

Faraday Waves↗

NASA NTRS1998

Bulk-Flow Analysis of Hybrid Thrust Bearings for Advanced Cryogenic Turbopumps

A bulk-flow analysis and computer program for prediction of the static load performance and dynamic force coefficients of angled injection, orifice-compensated hydrostatic/hydrodynamic thrust bearings have been completed. The product of the research is an efficient computational tool for the design of high-speed thrust bearings for cryogenic fluid turbopumps. The study addresses the needs of a growing technology that requires of reliable fluid film bearings to provide the maximum operating life with optimum controllable rotordynamic characteristics at the lowest cost. The motion of a cryogenic fluid on the thin film lands of a thrust bearing is governed by a set of bulk-flow mass and momentum conservation and energy transport equations. Mass flow conservation and a simple model for momentum transport within the hydrostatic bearing recesses are also accounted for. The bulk-flow model includes flow turbulence with fluid inertia advection, Coriolis and centrifugal acceleration effects on the bearing recesses and film lands. The cryogenic fluid properties are obtained from realistic thermophysical equations of state. Turbulent bulk-flow shear parameters are based on Hirs' model with Moody's friction factor equations allowing a simple simulation for machined bearing surface roughness. A perturbation analysis leads to zeroth-order nonlinear equations governing the fluid flow for the thrust bearing operating at a static equilibrium position, and first-order linear equations describing the perturbed fluid flow for small amplitude shaft motions in the axial direction. Numerical solution to the zeroth-order flow field equations renders the bearing flow rate, thrust load, drag torque and power dissipation. Solution to the first-order equations determines the axial stiffness, damping and inertia force coefficients. The computational method uses well established algorithms and generic subprograms available from prior developments. The Fortran9O computer program hydrothrust runs on a Windows 95/NT personal computer. The program, help files and examples are licensed by Texas A&M University Technology License Office. The study of the static and dynamic performance of two hydrostatic/hydrodynamic bearings demonstrates the importance of centrifugal and advection fluid inertia effects for operation at high rotational speeds. The first example considers a conceptual hydrostatic thrust bearing for an advanced liquid hydrogen turbopump operating at 170,000 rpm. The large axial stiffness and damping coefficients of the bearing should provide accurate control and axial positioning of the turbopump and also allow for unshrouded impellers, therefore increasing the overall pump efficiency. The second bearing uses a refrigerant R134a, and its application in oil-free air conditioning compressors is of great technological importance and commercial value. The computed predictions reveal that the LH2 bearing load capacity and flow rate increase with the recess pressure (i.e. increasing orifice diameters). The bearing axial stiffness has a maximum for a recess pressure rati of approx. 0.55. while the axial damping coefficient decreases as the recess pressure ratio increases. The computer results from three flow models are compared. These models are a) inertialess, b) fluid inertia at recess edges only, and c) full fluid inertia at both recess edges and film lands. The full inertia model shows the lowest flow rates, axial load capacity and stiffness coefficient but on the other hand renders the largest damping coefficients and inertia coefficients. The most important findings are related to the reduction of the outflow through the inner radius and the appearance of subambient pressures. The performance of the refrigerant hybrid thrust bearing is evaluated at two operating speeds and pressure drops. The computed results are presented in dimensionless form to evidence consistent trends in the bearing performance characteristics. As the applied axial load increases, the bearing film thickness and flow rate decrease while the recess pressure increases. The axial stiffness coefficient shows a maximum for a certain intermediate load while the damping coefficient steadily increases. The computed results evidence the paramount of centrifugal fluid inertia at low recess pressures (i.e. low loads), and where there is actually an inflow through the bearing inner diameter, accompanied by subambient pressures just downstream of the bearing recess edge. These results are solely due to centrifugal fluid inertia and advection transport effects. Recommendations include the extension of the computer program to handle flexure pivot tilting pad hybrid bearings and the ability to calculate moment coefficients for shaft angular misalignments.

SanAndres, Luis↗

NASA NTRS2009

Effectiveness of Needles Vial Adaptors and Blunt Cannulas for Drug Administration in a Microgravity Environment

The need for a new system of injectable medications aboard the International Space Station (ISS) was identified. It is desired that this system fly medications in their original manufacturer's packaging, allowing the system to comply with United States Pharmacopeia (USP) guidelines while minimizing the resupply frequency due to medication expiration. Pre-filled syringes are desired, however, the evolving nature of the healthcare marketplace requires flexibility in the redesign. If medications must be supplied in a vial, a system is required that allows for the safe withdrawal of medication from the vial into a syringe for administration in microgravity. During two reduced gravity flights, the effectiveness of two versions of a blunt cannula and needleless vial adaptors was evaluated to facilitate the withdrawal of liquid medication from a vial into a syringe for injection. Other parameters assessed included the ability to withdraw the required amount of medication and whether this is dependent on vial size, liquid, or the total volume of fluid within the vial. Injectable medications proposed for flight on ISS were used for this evaluation. Due to differing sizes of vials and the fluid properties of the medications, the needleless vial adaptors proved to be too cumbersome to recommend for use on the ISS. The blunt cannula, specifically the plastic version, proved to be more effective at removing medication from the various sizes of vials and are the recommended hardware for ISS. Fluid isolation within the vials and syringes is an important step in preparing medication for injection regardless of the hardware used. Although isolation is a challenge in the relatively short parabolas during flight, it is not an obstacle for sustained microgravity. This presentation will provide an overview of the products tested as well as the challenges identified during the microgravity flights.

Hailey, Melinda↗

NASA NTRS2020

High Pressure Transcritical Combustion (HPTC Combustion)

Combustion is the predominant source of the energy in the US and worldwide, and an overwhelming majority in the transportation sector, particularly liquid hydrocarbons (i.e., gasoline, diesel and jet fuel). Engine manufacturers move to higher operating pressures, above and beyond the critical pressures of the fuel, in order to optimize performance, maximize efficiency and reduce pollutant formation. The design of the next generation of engines, however, are limited by a lack of fundamental understanding of the thermo-physical properties, fluid behavior and chemical kinetics at these high pressures. Terrestrial laboratory studies are hampered by the ubiquitous buoyant flow that renders fundamental experiments difficult and/or impossible to interpret. Studying high pressure transcritical phenomena in microgravity allows researchers to investigate the fundamental aspects of phase change, chemical kinetics and property evaluation in a simplified geometry without the complicating influence of a buoyancy-induced flow.

Combustion↗

NASA NTRSDate not supplied

Surface Instability of Liquid Propellants in Microgravity During Pulsed Settling Operations

Pulsing reaction control system (RCS) thrusters, vent valves, or other propulsion devices can preserve propellant resources in space, but this operation also effectively introduces a vibration to the vehicle. When the vibration is perpendicular to the liquid propellant surface, Faraday waves may be generated at the liquid-vapor interface. These Faraday instabilities can perturb or break up the liquid surface of cryogenic tanks, leading to inefficiencies in thermal management or even ullage collapse. Drawing from theory and experiments, an engineering model defining the allowable design regions for pulsed settling in microgravity was assembled and verified with computational fluid dynamics (CFD) simulations. A traditional settling metric, the Bond number, was also overlaid in the model to indicate which duty cycles were insufficient to overcome surface tension and aggregate propellant. Mission planners and engineers can consult the tool to rapidly evaluate the stability of a liquid-vapor interface given the pulse frequency and the excitation acceleration. Expressions developed for Faraday waves induced by a sinusoidal forcing input at standard gravity were found to provide excellent predictive capabilities for pulsed, or rectangular, waveforms in the absence of a consistent gravitational acceleration. This study extends the usage of these equations to an alternative forcing function and microgravity environments for the purpose of estimating natural frequencies, surface mode shapes, surface wave amplitudes, and the onset of droplet ejection. CFD simulations with the Loci/STREAM-VoF (Volume of Fluid) solver were initially validated against experimental results in standard gravity. Discrete points on the design map were then investigated with CFD and confirmed that the engineering model reliably indicates surface stability and most Faraday wave characteristics without requiring higher-fidelity tools. The engineering model is highly extensible and can be adapted for various propellant fill fractions, fluid properties, and tank sizes.

Faraday Waves↗

DOE OSTI2025

Utilization of Existing Pipelines in Hydrogen Transport: Literature Review Report

This report critically reviews the flow behavior of hydrogen-natural gas (H 2 -NG) mixtures in pipelines and examines the critical factors of hydrogen integration into existing natural gas infrastructure. It addresses the choking behavior characterized by velocity increase and pressure drop, as well as the effects of flow restrictions and pressure losses during hydrogen transport. Computational and analytical models are used to investigate these effects, and their effects on thermodynamic properties and system performance are evaluated. The study also reviews the energy efficiency and flow dynamics of hydrogen and methane-hydrogen mixtures and optimizes the hydrogen flow rate. In addition, the effects of these mixtures on the flow characteristics are discussed in detail, with special emphasis on the compressibility factor (z factor) and fluid properties based on equations of state for hydrogen-natural gas mixtures. The study also analyzes the mixture ratios and highlights the thermophysical properties, flow dynamics, and hydrogen-blended natural gas application potential. These investigations assess flow stability, material interactions, and operational feasibility of transporting hydrogen mixtures through natural gas pipelines, which contribute to developing sustainable and efficient energy systems.

08 HYDROGEN↗

NASA NTRS2016

First-Principles Modeling of IAT-Driven Anomalous Resistivity in Hollow Cathode Discharges I: Theory

Self-consistent expressions are derived for the impact of ion acoustic turbulence (IAT) on the fluid properties of electrons and ions in the plume of a hollow cathode. This instability is believed to have a dominant role in the plasmadynamics in this region. The random phase approximation is applied to the perturbed Boltzmann equation to determine the effective drag and heating of the plasma species induced by the IAT. These driving terms are then incorporated into momentum and energy fluid equations for the ions and electrons. A fluid-like relation governing the evolution of the total IAT wave energy density is also presented. The physical significance of the IAT-based terms is discussed in the context of energy and momentum conservation, and a path forward is outlined for implementing the effects of IAT in the fluid-based model in Part II.

Jorns, Benjamin A.↗

NASA NTRS1998

Fluid Interface Phenomena in a Low-Gravity Environment: Recent Results from Drop Tower Experimentation

Drop towers used as experimental facilities have played a major role in the development of fundamental theory, engineering analysis, and the proofing of system designs applicable to fluid interface phenomena in a low-gravity environment. In this paper, the parameters essential to the effective use of drop tower experiments relevant to fluid interfaces with constant fluid properties are reviewed. The often dramatic influence of the contact angle and the uncertainty of the moving contact line boundary condition are emphasized. A number of sample problems buttressed by recent results from drop tower tests are discussed; these clearly demonstrate the role of inertia and the controlling influence of surface wettability and container geometry for the large length scale capillary flows that arise in fluid systems in space.

Weislogel, Mark M.↗

NASA NTRS2009

Ultimate Temperature of Pulse Tube Cryocoolers

An ideal pulse tube cryocooler using an ideal gas can operate at any temperature. This is not true for real gases. The enthalpy flow resulting from the real gas effects of 3He, 4He, and their mixtures in ideal pulse tube cryocoolers puts limits on the operating temperature of pulse tube cryocoolers. The discussion of these effects follows a previous description of the real gas effects in ideal pulse tube cryocoolers and makes use of models of the thermophysical properties of 3He and 4He. Published data is used to extend the analysis to mixtures of 3He and 4He. The analysis was done for pressures below 2 MPa and temperatures below 2.5 K. Both gases and their mixtures show low temperature limits for pulse tube cryocoolers. These limits are in the 0.5-2.2 K range and depend on pressure and mixture. In some circumstances, even lower temperatures may be possible. Pulse tube cryocoolers using the ha-fluid properties of dilute 3He in superfluid 4He appear to have no limit.

Kittel, Peter↗