SEARCH · Engineering Papers

Results for “failure criterion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Creep rupture behavior of unidirectional advanced composites

A 'material modeling' methodology for predicting the creep rupture behavior of unidirectional advanced composites is proposed. In this approach the parameters (obtained from short-term tests) required to make the predictions are the three principal creep compliance master curves and their corresponding quasi-static strengths tested at room temperature (22 C). Using these parameters in conjunction with a failure criterion, creep rupture envelopes can be generated for any combination of in-plane loading conditions and ambient temperature. The analysis was validated experimentally for one composite system, the T300/934 graphite-epoxy system. This was done by performing short-term creep tests (to generate the principal creep compliance master curves with the time-temperature superposition principle) and relatively long-term creep rupture tensile tests of off-axis specimens at 180 C. Good to reasonable agreement between experimental and analytical results is observed.

Yeow, Y. T.↗

NASA NTRS1981

A Voyager attitude control perspective on fault tolerant systems

In current spacecraft design, a trend can be observed to achieve greater fault tolerance through the application of on-board software dedicated to detecting and isolating failures. Whether fault tolerance through software can meet the desired objectives depends on very careful consideration and control of the system in which the software is imbedded. The considered investigation has the objective to provide some of the insight needed for the required analysis of the system. A description is given of the techniques which have been developed in this connection during the development of the Voyager spacecraft. The Voyager Galileo Attitude and Articulation Control Subsystem (AACS) fault tolerant design is discussed to emphasize basic lessons learned from this experience. The central driver of hardware redundancy implementation on Voyager was known as the 'single point failure criterion'.

Rasmussen, R. D.↗

NASA NTRS1981

Development of a simplified procedure for thrust chamber life prediction

An analytical design procedure for predicting thrust chamber life considering cyclically induced thinning and bulging of the hot gas wall is developed. The hot gas wall, composed of ligaments connecting adjacent cooling channel ribs and separating the coolant flow from the combustion gas, is subjected to pressure loading and severe thermal cycling. Thermal transients during start up and shut down cause plastic straining through the ligaments. The primary bending stress superimposed on the alternate in-plane cyclic straining causes incremental bulging of the ligaments during each firing cycle. This basic mechanism of plastic ratcheting is analyzed and a method developed for determining ligament deformation and strain. The method uses a yield surface for combined bending and membrane loading to determine the incremental permanent deflection and pregressive thinning near the center of the ligaments which cause the geometry of the ligaments to change as the incremental strains accumulate. Fatigue and tensile instability are affected by these local geometry changes. Both are analyzed and a failure criterion developed.

Porowski, J. S.↗

NASA NTRS1982

Mechanisms of deformation and fracture in high temperature low cycle fatigue of Rene 80 and IN 100

Specimens tested for the AGARD strain range partitioning program were investigated. Rene 80 and IN 100 were tested in air and in vacuum; at 871 C, 925 C, and 1000 C; and in the coated and uncoated condition. The specimens exhibited a multiplicity of high-temperature low-cycle fatigue damage. Observations of the various forms of damage were consistent with material and testing conditions and were generally in agreement with previous studies. In every case observations support a contention that failure occurs at a particular combination of crack length and maximum stress. A failure criterion which is applicable in the regime of testing studied is presented. The predictive capabilities of this criterion are straight forward.

Romanoski, G. R., Jr.↗

NASA NTRS1981

Problems encountered with conventional fiber-reinforced composites

Preparational, computational, and operational problems associated with fiber-reinforced composites (FRC) are reviewed. Initial preparation of FRCs is shown to involve consideration of the type of prepreg, the setting time, cure conditions and cycles, and cure temperatures. The effects of the choice of bonding agents, the fiber transfer length, and individual fiber responses to bonding agents are noted to have an impact on fiber strength, moisture uptake, and fatigue resistance. The deformation prior to failure and the failure region are modeled through models of mini-, micro- and macro mechanics formulations employing a stiffness matrix, failure criterion, or fracture mechanics. The detection, evaluation, and repair of defects comprises the operational domain, and it is stressed that no good repair techniques exist for FRCs.

Landel, R. F.↗

NASA NTRS1982

Finite element models for predicting crack growth characteristics in composite materials

Two dimensional and quasi-three dimensional, linear elastic finite element models for the prediction of crack growth characteristics, including crack growth direction, in laminated composite materials are presented. Mixed mode crack growth in isotropic materials, unidirectional and laminated composites is considered. The modified crack closure method is used to predict the applied load level for crack extension and two failure theories, modifications of the point stress and the Hashin failure criteria, are proposed to predict the direction of crack extension in composites. Comparisons are made with the Tsai-Wu failure criterion and the Sih strain energy density criterion as well as with experimental results. It is shown that the modified versions of point stress and Hashin criteria compare well with experiment.

Buczek, M. B.↗

NASA NTRS1983

The effect of extreme temperatures on the elastic properties and fracture behavior of graphite/polyimide composites

The influence of elevated and cryogenic temperatures on the elastic moduli and fracture strengths of several C6000/PMR-15 and C6000/NR-15082 laminates was measured. Tests were conducted at -157 C, 24 C, and 316 C (-250 F, 75 F, and 600 F). Both notched and unnotched laminates were tested. The average stress failure criterion was used to predict the fracture strength of quasi-isotropic notched laminates.

Morris, D. H.↗

NASA NTRS1984

Tensile Fracture of Ductile Materials

For brittle materials, circular voids play an important role relative to fracture, intensifing both tensile and compressive stresses. A maximum intensified tensile stress failure criterion applies quite well to brittle materials. An attempt was made to explore the possibility of extending the approach to the tensile fracture of ductile materials. The three dimensional voids that exist in reality are modelled by circular holes in sheet metal. Mathematical relationships are sought between the shape and size of the hole, after the material is plastically deformed, and the amount of deformation induced. Then, the effect of hole shape, size and orientation on the mechanical properties is considered experimentally. The presence of the voids does not affect the ultimate tensile strength of the ductile materials because plastic flow wipes out the stress intensification caused by them. However, the shape and orientation of the defect is found to play an important role in affecting the strain at fracture.

Pai, D. M.↗

NASA NTRS1984

The effect of extreme temperatures on the elastic properties and fracture behavior of graphite/polyimide composites

Morris, D. H.↗

NASA NTRS1984

Simulation of contact surface erosion for impact problems

An algorithm is outlined for simulating the contact surface erosion for impact problems. The algorithm dynamically relocates the contact surface as projectile and target materials exceed their failure criterion. Example computations of axisymmetric and oblique impacts are compared with experimental data.

Kimsey, K. D.↗

NASA NTRS1985

Thrust chamber life prediction

The reusable life of the Space Shuttle main engine (SSME) is influenced by the cyclic life of the regeneratively liquid cooled main combustion chamber (MCC). During an operational duty cycle the MCC liner is subjected to a large transient thermal gradient that imparts a high thermal cyclic strain to the liner hot gas wall. Life predictions of such chambers have usually been based on low cycle fatigue (LCF) evaluations. Hot-fire testing, however, has shown significant mid-channel wall deformation and thinning during accrued cyclic testing. This phenomenon is termed cyclic creep and appears to be significantly accelerated at elevated temperatures. An analytical method that models the cyclic creep phenomenon and its application to thrust chamber life prediction is presented. The chamber finite element geometry is updated periodically to account for accrued wall thinning and distortion. Failure is based on the tensile instability failure criterion. Cyclic life results for several chamber life enhancing coolant channel designs are compared to the typically used LCF analysis that neglects cyclic creep. The results show that the usable cyclic creep life is approximately 30 to 50% of the commonly used LCF life.

Kasper, H. J.↗

NASA NTRS1985

Effect of low-velocity or ballistic impact damage on the strength of thin composite and aluminum shear panels

Impact tests were conducted on shear panels fabricated from 6061-T6 aluminum and from woven fabric prepreg of Du Pont Kevlara fiber/epoxy resin and graphite fiber/epoxy resin. The shear panels consisted of three different composite laminates and one aluminum material configuration. Three panel aspect ratios were evaluated for each material configuration. Composite panels were impacted with a 1.27-cm (0.05-in) diameter aluminum sphere at low velocities of 46 m/sec (150 ft/sec) and 67 m/sec (220 ft/sec). Ballistic impact conditions consisted of a tumbled 0.50-caliber projectile impacting loaded composite and aluminum shear panels. The results of these tests indicate that ballistic threshold load (the lowest load which will result in immediate failure upon penetration by the projectile) varied between 0.44 and 0.61 of the average failure load of undamaged panels. The residual strengths of the panels after ballistic impact varied between 0.55 and 0.75 of the average failure strength of the undamaged panels. The low velocity impacts at 67 m/sec (220 ft/sec) caused a 15 to 20 percent reduction in strength, whereas the impacts at 46 m/sec (150 ft/sec) resulted in negligible strength loss. Good agreement was obtained between the experimental failure strengths and the predicted strength with the point stress failure criterion.

Farley, G. L.↗

NASA NTRS1985

Nonlinear response and failure characteristics of internally pressurized composite cylindrical panels

Results of an experimental and analytical study of the nonlinear response and failure characteristics of internally pressurized 4- to 16-ply-thick graphite-epoxy cylindrical panels are presented. Specimens with clamped boundaries simulating the skin between two frames and two stringers of a typical transport fuselage were tested to failure. Failure results of aluminum specimens are compared with the graphite-epoxy test results. The specimens failed at their edges where the local bending gradients and interlaminar stresses are maximum. STAGS nonlinear two-dimensional shell analysis computer code results are used to identify regions of the panels where the response is independent of the axial coordinate. A geometrically nonlinear one-dimensional cylindrical panel analysis was derived and used to determine panel response and interlaminar stresses. Inclusion of the geometric nonlinearity was essential for accurate prediction of panel response. The maximum stress failure criterion applied to the predicted tensile stress in the fiber direction agreed best with the experimentally determined first damage pressures.

Boitnott, R. L.↗

NASA NTRS1986

Reinforcement of composite laminate free edges with U-shaped caps

Generalized plane strain finite element analysis is used to predict reduction of interlaminar normal stresses when a U-shaped cap is bonded to the edge of a laminate. Three-dimensional composite material failure criteria are used in a progressive laminate failure analysis to predict failure loads of laminates with different edge cap designs. In an experimental program, symmetric 11-layer graphite-epoxy laminates with a one-layer cap of Kevlar-epoxy cloth are shown to be 130 to 140 percent stronger than uncapped laminates under static tensile and tension-tension fatigue loading. In addition, the coefficient of variation of the static tensile failure load decreases from 24 to 8 percent when edge caps are added. The predicted failure load calculated with the finite element results is 10 percent lower than the actual failure load. For both capped and uncapped laminates, actual failure loads are much lower than those predicted using classical lamination theory stresses and a two-dimensional failure criterion. Possible applications of the free edge reinforcement concept are described, and future research is suggested.

Howard, W. E.↗

NASA NTRS1986

ANISAP: A three-dimensional finite element program for laminated composites subjected to mechanical loading

ANISAP is a 3-D finite element FORTRAN 77 computer code for linear elastic, small strain, analysis of laminated composites with arbitrary geometry including free edges and holes. Individual layers may be isotropic or transversely isotropic in material principal coordinates; individual layers may be rotated off-axis about a global z-axis. The laminate may be a hybrid. Three different isoparametric elements, variable order of gaussian integration, calculation of stresses at element boundaries, and loading by either nodal displacement of forces are included in the program capability. Post processing capability includes failure analysis using the tensor polynominal failure criterion.

Burns, S. W.↗

NASA NTRS1986

Fatigue crack propagation rate model based on a dislocation mechanism

It has been noted that the crack propagation exponent p for most metals usually varies between values of 2 and 4, and that the motion of dislocations plays an important part in determining the exponent p. Attention is presently given to the significance of the exponent p in terms of the motion of dislocations, in view of the theory of thermally activated plastic flow and the cumulative plastic strain concept for a failure criterion.

Mazumdar, P. K.↗

NASA NTRS1986

Impact damage of composites

A model is described for estimating the impact damage of fiber reinforced composite plates. The displacements and stresses are calculated by a three dimensional transient, finite element method of solution of the governing equations applicable to a linearly elastic body. The region in which damage occurs is estimated using the Tsai-Wu failure criterion. A computer code was developed which can be used to calculate the impact force, displacements and velocities of the plate and the impact body, stresses and strains in the plate, and the damage area. Sample numerical results are presented illustrating the type of information provided by the code. Comparisons between measured and calculated damage areas are also given.

Wu, Hsi-Young T.↗

NASA NTRS1987

Comparisons of various configurations of edge delamination test for interlaminar fracture toughness

Tests were performed on brittle (T300/5208) and toughened-matrix (T300/BP907) graphite/epoxy laminates using various configurations of edge delamination tension (EDT) test specimens in order to assess the usefulness of each configuraion for measuring interlaminar fracture toughness. All configurations of the EDT test are found to be useful for ranking the delamination resistance of composites with different matrix systems. An analysis of test results suggests that delamination is governed by a linear failure criterion relating strain energy release components GI and GII.

O'Brien, T. Kevin↗