SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Variable frequency mechanical vibrator improves spark erosion cutting process. The vibration of the cutting tip permits continual flushing away of residue around the cut area with nondestructive electric transformer oil during the cutting process.
The backward problem of plasma assisted combustion emphasizes evaluating the effect of the evolving thermochemical state on the plasma discharge. This paper investigates the dependence of avalanche to streamer to spark formation dynamics and kinetics on the gas composition and temperature at different points in an ammonia-air premixed laminar flame using a self-consistent multigrid-based 1D plasma solver. Different values of ..alpha.., the coefficient for effective ionization events per unit length, have been reported for electron avalanches in air and stoichiometric NH3-air mixtures. The streamer inception has been shown to obey the Meek's criterion. An exponential reduction in streamer and spark formation time has been observed from plasma simulations at different points in the unburnt, pre-heat zone, reaction zone and the fully burnt regions of the premixed flame. While the enhancement of the reduced electric field with increasing temperature affects effective ionization, there exists a minimum breakdown field for streamer formation, which does not vary proportionally with the changing number density of the gas. The change in the mixture from reactants (NH3, O2, N2) to products of complete combustion of ammonia in air (N2, H2O) has also been shown to affect the streamer and spark formation. Finally, the major pathways during the streamer and spark phases which are responsible for producing important radicals used in combustion of NH3 are also discussed.
An investigation was conducted concerning the possible synthesis of a suite of dicarboxylic acids similar to that found in the Murchison meteorite. The investigation included the conduction of a chemical evolution experiment which simulated electric discharge through the primitive atmosphere of the earth. The suite of dicarboxylic acids obtained in the electric discharge experiment is similar to that of the Murchison meteorite, except for the fact that 2-chlorosuccinic acid is present in the spark discharge.
BHA Group Inc.'s PrecipTech Power Guard SQ-200 automatic voltage controller, combined with a remote computer, is an automatic management system for smoke-cleaning precipitators. It is the second generation of the SQ 100 developed at Langley Research Center, and was commercialized by two NASA employees. An electrostatic precipitator cleans the smoke by removing particulate matter from smokestack gases before gases are expelled into the atmosphere. Smokestack gas is passed through a precipitator chamber and exposed to an electrostatic field; dust particles in the gas become electrically charged, migrate to collection surfaces and are "captured." Developed under a NASA program seeking a way to dispose refuse, the system monitors sparking, automatically adjusts to changes in operating conditions and does not require a skilled operator.
Vulnerability of man-made infrastructure to Earth-directed space weather events is a serious concern for today's technology-dependent society. Space weather-driven geomagnetically induced currents (GICs) can disrupt operation of extended electrically conducting technological systems. The threat of adverse impacts on critical technological infrastructure, like power grids, oil and gas pipelines, and communication networks, has sparked renewed interest in extreme space weather. Because extreme space weather events have low occurrence rate but potentially high impact, this presents a major challenge for our understanding of extreme GIC activity. In this chapter, we discuss some of the key science challenges pertaining to our understanding of extreme events. In addition, we present an overview of GICs including highlights of severe impacts over the last 80 years and recent U.S. Federal actions relevant to this community.
This webinar is for prospective applicants (i.e., remote, island, and islanded communities) interested in applying to the U.S. Department of Energy's Energy Transitions Initiative Partnership Program (ETIPP) in spring of 2022. This webinar provides an overview of ETIPP and technical assistance, introduces the ETIPP regional partners, summarizes two ongoing ETIPP projects, discusses the 2022 application process, and closes with a question-and-answer session. This webinar is hosted by the National Renewable Energy Laboratory, which is part of the ETIPP partner network.
The City of Bainbridge Island (COBI) applied for and received technical assistance from the Energy Transitions Initiative Partnership Program (ETIPP) in part to achieve their goal of 100% renewable electricity generation by 2040, five years ahead of the Washington State goal, and to increase its energy resilience in the face of natural disasters. To help address these goals, the City of Bainbridge Island (COBI) applied for and received technical assistance from the Energy Transitions Initiative Partnership Program (ETIPP) during 2022-2024. Supported by the U.S. Department of Energy, ETIPP provides technical assistance to remote coastal and island communities interested in approaches to renewable and resilient energy transitions. Pacific Northwest National Laboratory (PNNL) completed the technical analysis aspects of the project, supported by the community partner Spark Northwest and the program administrator, the National Renewable Energy Laboratory (NREL). This report begins by describing the approach to technical assistance in the ETIPP project, followed by the development of future scenarios for electric demand based on current use. Potential pathways to 100% renewable energy are identified and analyzed by technology contributions from solar energy, anaerobic biodigestion, distributed wind, and marine energy. The combinations of these technologies and contributions to meet demand are discussed, along with potential policies and programs for implementation of the most relevant technologies moving forward. The report concludes with recommendations for next steps for COBI to meet the goal of 100% renewable energy generation by 2040 on- and off-island, and key caveats to consider.
A novel hybrid system enabling both flexible supercharging and limited torque assist is studied to mitigate transient response challenges of a turbocharged spark ignition engine equipped with low pressure exhaust gas recirculation. The hybrid system, called a power split supercharger (SC), is configured with a planetary gear set that splits the supercharging power between a small low-voltage electric motor and the engine crankshaft. The air path controller relies on the coordination of four actuators on the engine side and three low-level actuators on the hybrid boosting device. A decentralized control scheme is used in this work, in which the master–slave structure of the boost pressure controller decreases the turbo-lag associated with exhaust gas recirculation, while minimizing the SC operation for fuel economy. A vector reference governor is used to prevent compressor surge during engine tip-outs. In addition, the desired intake manifold pressure is modified to provide time for evacuating the exhaust gas recirculation and avoiding misfires when transitioning to low load, while the hybrid capability of the power split SC is used to recuperate the unwanted generated power. All controllers are validated on both a mean value engine model and a high-fidelity engine model. Practical challenges of implementing the vector reference governor to the highly nonlinear engine air path with pressure pulsations originating from the engine reciprocation are discussed and some solutions are proposed.
Effective diversion of surge currents is vital to prevent unwanted damage to sensitive electronics. Among the most successful and efficient strategies relies on a dielectric stimulated arc breakdown mechanism with high permittivity ceramic granules in a spark-gap geometry. Although generally regarded as a self-healing process, substantial energy deposition may occur that, over time, diminishes the ability to withstand repeated electrical assaults. We investigate the susceptibility of lead–magnesium–niobate–lead titanate (PMN–PT) granule microstructure and composition changes following many exposures to high voltage impulses resulting in arc breakdown. Scanning electron microscopy and energy-dispersive spectroscopy mapping reveal a broad range of thermal and mechanical defects entailing thermal reduction of constituent PMN–PT metal ions and recasting due to rapid eruption of volatile species. Additionally, evidence of local melting and microcracking are apparent that can have deleterious impact on the proper function of the granules, namely, the ability to concentrate electric fields across air gaps to establish and sustain discharge pathways. We propose that the localized nature of damage and stochasticity associated with the dielectric stimulated breakdown mechanism may allow granules to maintain functionality provided no permanent conduction paths are established.
From considerations of safety and reliability in performance of gas-turbine aircraft, it is clear that engine starting and acceleration are of utmost importance. For this reason extensive efforts have been devoted to the investigation of the factors involved in the starting and acceleration of engines. In chapter III it is shown that certain basic combustion requirements must be met before ignition can occur; consequently, the design and operation of an engine must be tailored to provide these basic requirements in the combustion zone of the engine, particularly in the vicinity of the ignition source. It is pointed out in chapter III that ignition by electrical discharges is aided by high pressure, high temperature, low gas velocity and turbulence, gaseous fuel-air mixture, proper mixture strength, and-an optimum spark. duration. The simultaneous achievement of all these requirements in an actual turbojet-engine combustor is obviously impossible, yet any attempt to satisfy as many requirements as possible will result in lower ignition energies, lower-weight ignition systems, and greater reliability. These factors together with size and cost considerations determine the acceptability of the final ignition system. It is further shown in chapter III that the problem of wall quenching affects engine starting. For example, the dimensions of the volume to be burned must be larger than the quenching distance at the lowest pressure and the most adverse fuel-air ratio encountered. This fact affects the design of cross-fire tubes between adjacent combustion chambers in a tubular-combustor turbojet engine. Only two chambers in these engines contain spark plugs; therefore, the flame must propagate through small connecting tubes between the chambers. The quenching studies indicate that if the cross-fire tubes are too narrow the flame will not propagate from one chamber to another. In order to better understand the role of the basic factors in actual engine operation, many investigations have been conducted in single combustors from gas-turbine engines and in full-scale engines in altitude tanks and in flight. The purpose of the present chapter is to discuss the results of such studies and, where possible, to interpret these results qualitatively in terms of the basic requirements reported in chapter III. The discussion parallels the three phases of turbojet engine starting: (1) Ignition of the fuel-air mixture (2) Propagation of flame throughout the combustion zone (3) Acceleration of the engine to operating speed.
Test program evaluates thermal and electric ignition mechanisms in selected nonmetallic materials found in spacecraft with concentrated oxygen atmospheres. The phenomena evaluated were spontaneous ignition, ignition of flammable vapor by a spark, and ignition by an arc where the arc produces the combustible vapor and the ignition source.
Through the SBIR program, DSSP developed a multi-pulse solid rocket motor for NASA that will enable stabilized interplanetary flight for small satellites. Another of DSSP’s core innovations with roots in the SBIR program is already having an even greater impact. Originally proposed to fuel a microsatellite thruster for Earth-observation missions, DSSP’s HAN-based green electric monopropellants (GEM and AF-M315E) technology is powering larger satellites, enhancing downhole oil and gas recovery, and much more. Highly insensitive to ignition by spark, flame, or shock, GEM-based innovations are stable, non-toxic, and more controllable than conventional propellants.
This study investigates interrelations between one-electrode Cavitation-Assisted Electric Discharge (CAED), two-electrode CAED, and recently discovered Intense CAED (I-CAED). The one-electrode CAED is a self-triggered nanosecond discharge with pulse energy in the micro-Joule range, which can be generated even by a DC voltage. I-CAED consists of a non-equilibrium part within a low-pressure cavitating region and a micro-spark traversing a liquid film. We hypothesize that CAED propagates from the high-voltage electrode as an ionization wave through bubbles of saturated vapor. Subsequently, the streamer-like discharges in the bubbles may form a continuous plasma channel. Inside the cavitating region, the plasma is strongly non-equilibrium, providing an ideal environment for generating chemically unstable species such as hydrogen peroxide (H 2 O 2 ). Plasma of I-CAED spark is characterized by high electron density and near-thermal equilibrium, emitting a continuous ultraviolet spectrum. The combination of these different discharge parts makes I-CAED in water a highly effective tool for the Advanced Oxidation Process, particularly in water disinfection. Experimentally demonstrated Electric Energy per Order value for disinfection of E. coli-contaminated water is as low as 0.135 ± 0.035 kWh/m 3 /order. Estimates show that the implementation of “dry electrodes” configuration reduces the erosion rate of the electrode material by at least one order of magnitude. Spectral analysis reveals that the continuum emission generated by I-CAED in proximity to metal electrodes deviates from the spectra of discharges spatially decoupled from the electrodes. We assume that this spectral divergence is attributable to blackbody-like emission originating from metallic nanoparticles form during the electrode's erosion process.
This paper reviews ceramic substrates and thick-film metallization based packaging technologies in development for 500degC silicon carbide (SiC) electronics and sensors. Prototype high temperature ceramic chip-level packages and printed circuit boards (PCBs) based on ceramic substrates of aluminum oxide (Al2O3) and aluminum nitride (AlN) have been designed and fabricated. These ceramic substrate-based chiplevel packages with gold (Au) thick-film metallization have been electrically characterized at temperatures up to 550degC. A 96% alumina based edge connector for a PCB level subsystem interconnection has also been demonstrated recently. The 96% alumina packaging system composed of chip-level packages and PCBs has been tested with high temperature SiC devices at 500degC for over 10,000 hours. In addition to tests in a laboratory environment, a SiC JFET with a packaging system composed of a 96% alumina chip-level package and an alumina printed circuit board mounted on a data acquisition circuit board was launched as a part of the MISSE-7 suite to the International Space Station via a Shuttle mission. This packaged SiC transistor was successfully tested in orbit for eighteen months. A spark-plug type sensor package designed for high temperature SiC capacitive pressure sensors was developed. This sensor package combines the high temperature interconnection system with a commercial high temperature high pressure stainless steel seal gland (electrical feed-through). Test results of a packaged high temperature capacitive pressure sensor at 500degC are also discussed. In addition to the pressure sensor package, efforts for packaging high temperature SiC diode-based gas chemical sensors are in process.
This paper reviews ceramic substrates and thick-film metallization based packaging technologies in development for 500 C silicon carbide (SiC) electronics and sensors. Prototype high temperature ceramic chip-level packages and printed circuit boards (PCBs) based on ceramic substrates of aluminum oxide (Al2O3) and aluminum nitride (AlN) have been designed and fabricated. These ceramic substrate-based chip-level packages with gold (Au) thick-film metallization have been electrically characterized at temperatures up to 550 C. A 96% alumina based edge connector for a PCB level subsystem interconnection has also been demonstrated recently. The 96% alumina packaging system composed of chip-level packages and PCBs has been tested with high temperature SiC devices at 500 C for over 10,000 hours. In addition to tests in a laboratory environment, a SiC JFET with a packaging system composed of a 96% alumina chip-level package and an alumina printed circuit board mounted on a data acquisition circuit board was launched as a part of the MISSE-7 suite to the International Space Station via a Shuttle mission. This packaged SiC transistor was successfully tested in orbit for eighteen months. A spark-plug type sensor package designed for high temperature SiC capacitive pressure sensors was developed. This sensor package combines the high temperature interconnection system with a commercial high temperature high pressure stainless steel seal gland (electrical feed-through). Test results of a packaged high temperature capacitive pressure sensor at 500 C are also discussed. In addition to the pressure sensor package, efforts for packaging high temperature SiC diode-based gas chemical sensors are in process.
Spark discharges induce a complex flow field consisting of a shock wave at early times (~ 1 μs), a pair of vortex rings, and a hot gas kernel. The vortex rings entrain ambient gas into the hot gas kernel and control its cooling and expansion. In this work, we investigate the shock wave's contribution in producing the vortex ring vorticity. We analyze high-speed (700 kHz) schlieren images of the shock wave for a range of electrical energies to measure the shock properties and estimate shock velocity and curvature. These measurements are combined with a model to calculate the vorticity generated. The measurements show that the highest vorticity is generated near the peak shock curvature location, and the shock curvature and strength increase with electrical energy deposited. A comparison of the vorticity estimated from the model to vorticity measurements from stereoscopic particle image velocimetry shows the results to be statistically equivalent. Furthermore, this suggests that the shock curvature and velocity contribute to the vortex rings induced by spark discharges.
Battery case, equipped with relief valve, connector, and two covers, separates the explosive mixture from all potential spark sources. Bottom ends of vent tubes are cemented into cell vents and upper ends fit through the gas barrier cover. This arrangement isolates generated gases from the electric power.
The high probability for dust interactions during Martian dust storms and dust devils combined with the cold, dry climate of Mars most likely result in airborne dust that is highly charged. On Earth, potential gradients up to 5 kV/m have been recorded and in some cases resulted in lightning. Although the Martian atmosphere is not conducive to lightning generation, it is widely believed that electrical discharge in the form of a corona occurs. In order to understand the breakdown of gases, Paschen measurements are taken which relate the minimum potential required to spark across a gap between two electrodes. The minimum potential is plotted versus the pressure-distance value for electrodes of a given geometry. For most gases, the potential decreases as the pressure decreases. For CO2, the minimum in the curve happens to be at Mars atmospheric pressures (5-7 mm Hg) for many distances and geometries. However, a very small amount (<0.1%) of mixing gases radically changes the curve, as noted by Leach. Here, we present the first experimental results of a Paschen curve for a Mars gas mixture compared with 100% pure CO2.