SEARCH · Engineering Papers
Results for “depth migration”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
INVESTIGATION OF ROCK-FLUID INTERACTIONS USING GEOMATERIAL MICROFLUIDICS
Illite and Illite-Smectite clays are reportedly the Caney Shale's most prevalent clay minerals. The swelling and fines migration of clays may occur when water-based fluids contact the clay minerals. This may result in the reduction of pore space and permeability, and wettability alteration. Therefore, we quantified the swelling potentials, fines migration and wettability alteration of Illite and Illite-Smectite clays upon exposure to model brines and a produced water, and a model oil and a crude oil. We measured density, viscosity, pH, TDS, and interfacial tension as they are important in multiphase flow and displacement characteristics. Geomaterial microfluidics is recently being used to study physicochemical interactions of solid-fluid systems. It facilitates visualizing the surface behavior upon exposure to various fluids. This study includes preparation and characterization of Illite-Smectite clay-coated glass capillary tubes. Illite and Illite-Smectite clay-coated geomaterial microfluidic surfaces were prepared to investigate the effects of first contact fluid, brine salinity, and aging on wettability. In this work, advancing and receding contact angles of model brine-air, model oil-air, produced water-air, crude oil-air, model brine-model oil systems, and produced water-crude oil systems have been measured in the untreated, and clay-coated microfluidic channels of 1000 µm width and 50 µm depth. The aging effect was studied by retaining the non-aqueous and aqueous solutions in the corresponding microfluidic channels for approximately 24 h in the case of channels first contacted by aqueous and non-aqueous solutions, respectively. The advancing and receding contact angles of Caney shale-crude oil-produced water systems were also measured. The experimental findings indicate the swelling potential, fines migration, and wettability alteration of Illite and Illite-Smectite clays. The results signify the influence of first contact fluid, brine salinity, and aging on wettability of the untreated and clay-coated microfluidic surfaces. The experiments also demonstrate the wetting nature of the Caney shale samples from reservoir and non-reservoir zones.
Lunar asymmetry and palaeomagnetism
A model is proposed for the early lunar evolution which accounts for the compositional asymmetry between the nearside and farside of the moon and the natural remanent magnetism of lunar rocks. According to the model, the preferred gravitational energy state consisted of an asymmetric accumulation of a liquid iron alloy (Fe-Ni and a small amount of sulfur) which displaces upwards the cold primordial undifferentiated core. The resulting depth asymmetry of the outer partially molten zone leads eventually to the subcrustal accumulation of light magnesium-rich pyroxenes and olivine, preferentially in one hemisphere, sufficient to explain the offset and also indirectly providing a possible explanation for the nearside concentration of KREEP and mass basalt. Slow downward migration of iron releases gravitational energy sufficient for convection and dynamo generation in an iron layer for about a billion years.
Northward propagation of the Gulf of Elat-Aqaba constrained by cosmogenic burial ages and magnetostratigraphy of onshore sediments
The Gulf of Elat-Aqaba (GEA), located in the southern part of the Dead Sea Transform (DST), is one of the most active segments of the Dead Sea fault system. Yet, some fundamental details concerning its evolution in space and time are still not fully understood. To better constrain the tectonic history of this region, we study a succession of alluvial, lacustrine, and fluvial deposits in the north-western edge of the GEA, which belong to the Quaternary Eilot and Garof Fms. The Eilot Fm. represents low-energy shallow freshwater bodies and sabkhas, which predate the development of the deep part of the basin. Later, in response to the subsidence of the basin, the Garof Fm. was deposited in alluvial fans that built up following the increase in the depositional energy. Cosmogenic burial ages combined with magnetostratigraphy show that these Fms. were deposited as early as 3.03 Ma and as late as 1.65 Ma, depending on the applied age model. Considering the present depth of the northern GEA, this age indicates a maximum subsidence rate of the head of the GEA of ~1.98mm/yr. We suggest that faults along the onshore margin of the deep basin were active during the deposition of the Garof Fm. and subsequently became inactive, while the faulting activity migrated toward the center of the basin. In conclusion, closed Holocene basins north of the present seashore, such as the Elat and Evrona playas, which may represent a modern analogue to the Plio-Pleistocene morphology, raise the possibility that the GEA head is still propagating northward.
Tree Diversity, Site Index, and Carbon Storage Decrease With Aridity in Douglas-Fir Forests in Western Canada
Forests are important for biodiversity, timber production and carbon accumulation, but these ecosystem services may be impacted by climate change. Field data collected from individual forest types occurring across a climatic gradient can contribute to forecasting these consequences. We examined how changes in temperature, precipitation and aridity affect ecosystem services in 23 mature Douglas-fir (Pseudotsuga menziesii) forests in nine climatic regions across a 900 km gradient in British Columbia, Canada. Using Canadian National Forest Inventory methodology, we assessed richness and diversity of plant functional groups, site index, and above- and below-ground carbon stocks. As aridity increased, ecosystem-level tree species richness declined on average from four to one species, Douglas-fir site index declined from 30 to 15 m, and ecosystem carbon storage decreased from 565 to 222 Mg ha –1 . Tree species richness was positively and herb species richness negatively correlated with carbon storage. Carbon storage by ecosystem compartment was largest in aboveground live tree biomass, declining in the following order: mineral soils > coarse woody debris and dead standing trees > forest floor > small and fine woody debris > understory plants. Mineral soil carbon at depths of 0-15 cm, 15-35 cm, and 35-55 cm increased with increasing mean annual precipitation and decreasing aridity. Our results indicate that as aridity increases and precipitation decreases, tree species richness, site index and carbon storage in existing Douglas-fir forests declines. However, assisted or natural migration of Douglas-fir into more humid regions could be associated with more diverse, productive, carbon-rich forests. This study informs carbon stock vulnerability and provides empirical data essential for carbon stock forecasts.
Large silver-cadmium technology program
The effects of varying cell design on operation factors on the electrochemical performance of sealed, silver-cadmium cells were determined. A factorial experiment was conducted for all test cells constructed with organic separators. Three operating factors were evaluated: temperature, depth of discharge, and charge rate. The six construction factors considered were separator, absorber, electrolyte quantity, cadmium electrode type, cadmium-to-silver ratio, and auxiliary electrode. Test cells of 4 ampere-hour capacity were fabricated and cycled. The best performing cells, on a 94 minute orbit, at 40% depth of discharge, were those containing silver-treated fibrous sausage casings as the separator, and Teflon-ated, pressed cadmium electrodes. Cycling data of cells with inorganic separators (Astroset) are given. Best performance was shown by cells with nonwoven nylon absorbers. Rigid inorganic separators provided the best barrier to silver migration.
Analysis of Hydrology and Interim Measure Performance in the Chromium Plume at Los Alamos National Laboratory - 20498
Hexavalent chromium, Cr(VI), is present in the regional aquifer beneath Los Alamos National Laboratory (LANL) at concentrations greater than the New Mexico groundwater standard (50 ppb). The source of the Cr is blowdown from a power plant where potassium dichromate was used as a corrosion inhibitor from 1956 to 1972. Blowdown comingled with effluent from another source and migrated approximately 3 miles down a canyon, primarily as surface flow, until reaching an alluvial infiltration zone. The infiltrating water moved vertically through a thick (approximately 900 ft), complex stratigraphic sequence of unsaturated tuffs, basalt, and unconsolidated alluvial deposits. Horizontal transport also took place within spatially limited perched groundwater horizons in the vadose zone (VZ). Breakthrough at the regional aquifer water table is thought to have occurred in multiple hydraulic windows or 'drip points' located approximately 3 miles from the initial release site at the power plant. The regional aquifer is highly heterogeneous and anisotropic, and displays unconfined behavior in an upper zone and confined behavior at depth. The Cr(VI) contamination has so far remained confined to the upper approximately 25 m of the aquifer. The ambient hydraulic gradient in the regional aquifer is toward the east/southeast, but the water table is extremely flat in the Cr plume area compared to surrounding areas. There is some local variability in flow direction, potentially related to effects of seasonal pumping from nearby Los Alamos county water-supply wells, which draw from the regional aquifer several hundred feet below the water table. An interim measure (IM) is currently operating at the site to achieve hydraulic control of plume migration using a series of extraction wells, ion-exchange treatment, and injection along the downgradient portion of the plume. The migration of Cr contamination in the aquifer has been previously evaluated using a calibrated probabilistic numerical model, which has also been used to design the spatial configuration of extraction and injection wells for the IM, and to identify locations for monitoring wells. The model is built using the Finite Element Heat and Mass (FEHM) transfer code, and the Model Analysis and Decision Support (MADS) software is used for analyses. To date, the portion of the IM system that has operated in a continuous manner has been very effective at hydraulic control. Modifications to the flow field associated with the influence of IM pumping and injection are evaluated here, with modeling constraints to be provided by recent observations of tracers injected into both monitoring wells and IM injection wells, as well as opportunistic observations of geochemical signatures of treated ion-exchange effluent injected into IM injection wells. The tracer and geochemical data provide insights into modified flow directions within the Cr plume area that cannot be otherwise obtained. Results of the modeling work are being used to inform adaptive management of IM operations and will be a valuable tool for development and refinement of long-term remediation strategies. (authors)
Trace elements profiles, notably Hg, from a preliminary study of the Apollo 15 deep-drill core.
The possible thermal gradient near the surface during a lunation is considered together with the heat flow from the interior, the physical process of Hg migration, the results from core and trench samples from previous missions, and other temperature sensitive phenomena that may help understand the processes. U, Os, and Ru concentrations in the deep drill core samples are of potential interest and are summarized in a table. The Os tends to parallel the Hg profile with depth.
Modeling of ExB effects on tungsten re-deposition and transport in the DIII-D divertor
Mixed-material DIVIMP-WallDYN modelling, now incorporating ExB drifts, is presented that simultaneously reproduces tungsten (W) erosion and deposition patterns observed during the DIII-D Metal Rings Campaign, in which a toroidally symmetric set of W-coated tiles were installed in the carbon (C) DIII-D divertor. Since most reactor plasma facing component (PFC) designs call for mixed-material environments, including ITER’s W/Be enviroment, the divertor targets will quickly evolve into reconstitued surfaces of multiple elements. This work identifies controlling physics that affects material migration patterns in the divertor, which impact PFC lifetimes and impurity leakage from the divertor to the core. These simulations indicate that radial and poloidal ExB transport dominates over parallel force balance for high-Z impurities such as W in the divertor region of DIII-D. It is demonstrated that ExB drifts are required to reproduce the experimental observation of non-local W and C co-accumulation in a band ~7-9 cm outboard of the outer-strike-point (OSP) W source, for attached Lmode conditions in the unfavorable ion grad-B drift direction. In addition, W gross erosion is localized to the region outboard of the OSP, as the formation of C co-deposits suppresses W erosion at the strike point. Time-dependent simulations with scaled ExB impurity drifts (60% of the OEDGE-calculated drift velocity) and W re-erosion quantitatively reproduce these features, including depth-resolved W/C ratios, within a factor of 2 over ~115 seconds of accumulated plasma exposure. The location of co-deposition regions is shown to be well represented by an analytic leakage model, driven largely by poloidal ExB drifts. Qualitative agreement is also found between campaign-integrated W deposition measurements and simulations for the favorable ion grad-B drift direction, the standard mode of operation for most tokamaks. Furthermore, these results imply that a longterm inward radial migration of material from the outer divertor through the private flux region may occur in future devices.
An Historical Search for Unfrozen Water at the Phoenix Landing Site
The goal of this work is to explore the history of the high-latitude subsurface in the latitude range of the Phoenix landing site (65-75 deg. N). The approach is to use time-marching climate models to search for times, locations, and depths where thick films of unfrozen water might periodically occur. Thick films of unfrozen water (as distinct from ubiquitous monolayer water) are interesting for two reasons. First, multi-layer films of water may be bio-available. Second, patterned ground may require the occurrence of thick films of unfrozen water to facilitate the migration of particles and the development of excess pore ice, as reported by the Odyssey Gamma Ray Spectrometer (GRS) results. For the purposes of this work, we define conditions adequate to establish thick films of unfrozen water to be T greater than 268 K, and RH greater than 0.5. We start with the need to understand the atmospheric pressure. Because of the fact that we're looking at high latitudes, the seasonal cap buffers surface temperature for some part of the year. That directly affects the subsurface thermal regime, at least in the uppermost meter where we will be
Polar Wander on Triton and Pluto Due to Volatile Migration
Polar wander may occur on Triton and Pluto because of volatile migration. Triton, with its low obliquity, can theoretically sublimate volatiles (mostly nitrogen) at the rate of approximately 10(exp 14) kilograms per year from the equatorial regions and deposit them at the poles. Assuming Triton to be rigid on the sublimation timescale, after approximately 10(exp 5) years the polar caps would become large enough to cancel the rotational flattening, with a total mass equivalent to a global layer approximately 120-250 m in depth. At this point the pole wanders about the tidal bulge axis, which is the line joining Triton and Neptune. Rotation about the bulge axis might be expected to disturb the leading side/trailing side cratering statistics. Because no such disturbance is observed, it may be that Triton's mantle viscosity is too high but its surface volatile inventory is too low to permit wander. On the other hand, its mantle viscosity might be low, so that any uncompensated cap load might be expected to wander toward the tidal bulge axis. In this case, the axis of wander passes through the equator from the leading side to the trailing side; rotation about this wander axis would not disturb the cratering statistics. Low-viscosity polar wander may explain the bright southern hemisphere: this is the pole which is wandering toward the equator. In any case the permanent polar caps may be geologically very young. Polar wander may possibly take place on Pluto, due to its obliquity oscillations and perihelion-pole geometry. However, Pluto is probably not experiencing any wander at present. The Sun has been shining strongly on the poles over the last half of the obliquity cycle, so that volatiles should migrate to the equator, stabilizing the planet against wander. Spacecraft missions to Triton and Pluto which measure the dynamical flattening could give information about the accumulation of volatiles at the poles. Such information is best obtained by measuring gravity and topography from orbiters, as was done for Mars with the highly successful Mars Global Surveyor.
Preliminary Analysis of Source Physics Experiment Explosion-Triggered Microseismicity Using the Back-Projection Method
A series of four chemical explosions were detonated in a deep borehole within the Yucca Flat Dry Alluvium Geology (DAG) at the Nevada National Security Site between 2018 and 2019. The two larger chemical explosions of 50 tons (DAG-2) and 10 tons (DAG-4) TNT equivalent yield triggered energetic aftershock sequences numbering 1392 and 347 microearthquakes, respectively, within the first 10 days. No significant aftershock activity was observed for the two smaller 1-ton explosions (DAG-1 and DAG-3). Here, we used a back-projection method based on travel-time migration and stacking of signal-to-noise ratio traces to detect, associate and locate aftershocks from a subset of 22-geophones within a larger 2 urn:x-wiley:21699313:media:jgrb54910:jgrb54910-math-0001 2 km seismic array surrounding the borehole. The aftershocks located within 300 m of the borehole and the depths were above the working points of 300 and 50 m depths of DAG-2 and DAG-4, respectively, ruling out triggering slip on geologic faults or disturbances beneath neighboring collapse craters. DAG-2 and DAG-4 aftershocks decayed at similar rates, with power-law exponents of p = 1.48 and p = 1.49, respectively. These decay rates are comparable to aftershocks sequences triggered by earthquakes and historical nuclear explosions at Yucca Flat. A smooth power-law aftershock decay within the first 10 days suggests a triggering mechanism from explosion generated stress relaxation due to the diffusion of high gas pressures in the cavity and radial fractures. A more random and episodic aftershock rate would be expected due to cavity collapse or falling rubble in chimney formation.
Molecular dynamics and quasidynamics simulations of the annealing of bulk and near-surface interstitials formed in molecular-beam epitaxial Si due to low-energy particle bombardment during deposition
The relaxation, diffusion, and annihilation of split and hexagonal interstitials resulting from 10 eV Si irradiation of (2x1)-terminated Si(100) are investigated. Molecular dynamics and quasidynamics simulations, utilizing the Tersoff many-body potential are used in the investigation. The interstitials are created in layers two through six, and stable atomic configurations and total potential energies are derived as a function of site symmetry and layer depth. The interstitial Si atoms are allowed to diffuse, and the total potential energy changes are calculated. Lattice configurations along each path, as well as the starting configurations, are relaxed, and minimum energy diffusion paths are derived. The results show that the minimum energy paths are toward the surface and generally involved tetrahedral sites. The calculated interstitial migration activation energies are always less than 1.4 eV and are much lower in the near-surface region than in the bulk.
Interim Measures Work Plan: South Repeater Building: Solid Waste Management Unit 121: Hydraulic Containment and Groundwater Treatment System for Per- and Polyfluoroalkyl Substances: Kennedy Space Center, Florida
This document presents the design details of a granular activated carbon (GAC) hydraulic containment and groundwater treatment system Interim Measures Work Plan for the South Repeater Building site (South Repeater, Solid Waste Management Unit 121), located at John F. Kennedy Space Center (KSC), Florida. The interim measures (IM) treatment area includes the source area and downgradient property boundary, which have been impacted by per- and polyfluoroalkyl substances (PFAS). The objectives of the IM are to treat the source area and mitigate PFAS migration to areas outside of KSC boundaries. This document was prepared by AECOM Technical Services, Inc., for the National Aeronautics and Space Administration under Contract 80KSC019D0010, Task Order 80KSC021F0096. The IM consists of the installation and operation of 19 extraction wells and an associated groundwater treatment system. A total of 13 wells will be installed to a depth of 34 feet below land surface (bls) to target the upper medium-grained sand with shell layer. A total of six wells will be installed to a depth of 56 feet bls to target the lower layer of poorly graded sand with shell fragments. The system will be designed to operate each extraction well simultaneously using submersible pumps at flow rates of 5 or 10 gallons per minute (gpm), excluding one extraction well with a flow rate of 30 gpm. The extracted groundwater will be conveyed to a groundwater treatment system, where it will be treated via GAC prior to disposal via infiltration. To evaluate treatment system performance, baseline groundwater sampling will be conducted prior to treatment system startup. Performance monitoring will be completed quarterly for the first year. A total of eight performance monitoring wells will be installed to a depth of 12 feet bls, and eight performance monitoring wells will be installed to a depth of 30 feet bls. In addition to the installation of 16 performance monitoring wells, 12 existing monitoring wells will be incorporated into the performance monitoring program.
Determining the extent of potential fugitive fluid migration from geologic carbon storage in hydrocarbon-bearing reservoirs: Insights from one-dimensional numerical modeling
Numerical modeling of Geologic Carbon Sequestration in permeable reservoirs initially containing hydrocarbons is conducted using the multi-phase, multi-component thermohydrologic simulator TOGA (TOUGH Oil, Gas, Aqueous; TOUGH stands for Transport Of Unsaturated Groundwater and Heat), to determine how phase and composition of the original fluids influence the extent of the zone where upward fugitive fluid migration could potentially occur, denoted R f . The area within R f comprises regions of substantially elevated pressure and free-phase CO 2 saturation, where a breach in reservoir sealing capacity would lead to upward fugitive fluid migration. The model examines the conditions within the storage reservoir that could lead to fugitive flow, but does not model the fugitive flow itself. A one-dimensional radial model of the storage reservoir is used, and three initial phase conditions are considered: single-phase aqueous, two-phase gas-aqueous, and three-phase oil-gas-aqueous. Components that may be present are H 2 O, CO 2 , CH 4 , C 4 H 10 , and C 10 H 22 . The most important factors controlling Rf are (1) the initial gas-phase saturation within the reservoir, and (2) the lateral extent of multi-phase initial conditions, particularly CO 2 . The composition of liquid and gas phases has a secondary effect. The impact of reservoir depth, thickness, injection rate, and hydrologic properties are also briefly examined, with thickness (or equivalently injection rate) having the biggest effect. These results can help to understand important trends in potential response of CO 2 -EOR fields being considered for dedicated CO 2 storage.
A Systems Biology Approach to Energy Flow in H 2 Producing Microbial Communities: Microbial Mats
This report describes the results of work conducted at NASA Ames Research Center, in collaboration with investigators at Lawrence Livermore National Laboratory, during the time period 12/15/2014 to 12/15/2017. The work was an extension of a collaboration with LLNL that began in 2008. Work this reporting period focused primarily on tasks related to microbial mats from both the Elkhorn Slough and Baja California field sites, including the analysis and publication of data produced prior to 12/15/2014. During this reporting period, in addition to the microbial mat work, we also conducted a series of experiments with a particular algal-bacterial association (C. sorokiniana and A. brasilense). A number of aspects of this well-characterized algal-bacterial association enabled us not only to further our understanding of interactions between these particular organisms, but to apply that knowledge and techniques to our collection of microorganisms isolated from microbial mats. Microbial mat experiments focused both on intact mat communities and on cultures of organisms isolated from the mats (the Microbial Mat Living Library). In a series of co-culture experiments, we documented both positive and negative interactions amongst heterotrophic and autotrophic isolates of microbial mat microorganisms. One particularly important and novel mat cyanobacterium (ESFC-1) was studied in detail. We developed techniques to pursue an investigation of functional redundancy (the idea that closely related organisms perform identical roles in a community) in cyanobacterial autotrophs in the Elkhorn Slough microbial mat. In those experiments, we documented numerous instances of increases in growth rate between co-cultures of two organisms (relative to their growth rate in isolation) performing what would seem to be identical functional roles. Simplified microbial mat communities consisting of organisms from the Microbial Mat Living Library were constructed and studied in laboratory experiments. The “constructed mats” were grown in standard laboratory glassware and plasticware, but cultures were also combined with artificial materials in an effort to re-create the three-dimensional structure of naturally occurring microbial mats. These constructed mats re-created a number of functions attributable to natural microbial mats (N-fixation, H2-production) and simplified their study using molecular ecological techniques due to the smaller number of microbial “species” present. Cyanobacteria which migrated in response to vertical variations in light intensity (irradiance) obtained characteristic positions in constructed mats that were similar to their positions in natural mats. A detailed investigation of nitrogen cycling in both the Baja California and Elkhorn Slough microbial mats was initiated during this reporting period. The nitrogen cycle in the microbial mats has not been studied in depth, despite the fact that nitrogen usually limits growth in marine environments. The organisms conducting nitrogen cycling in both microbial mats were studied using the genomes available from earlier work on these mats, as well as with a targeted approach using molecular ecological methods developed here. Quantitative measurements of rates of nitrogen transformations were made using stable isotopically labeled nitrogen. The processes quantified and examined using molecular ecological methods included: nitrogen fixation, ammonification, ammonium and nitrate assimilation, denitrification, anaerobic oxidation of ammonium, and dissimilatory nitrate reduction to ammonium. In a series of experiments designed to examine a potential application for microbial mats, we demonstrated that both Elkhorn Slough and Baja California microbial mats were very effective in removing large quantities of both nitrate and ammonium from waste streams containing these compounds at levels where they would be considered to be pollutants. Considerable effort was expended during this reporting period to analyze, and prepare for publication, metagenomes and metatranscriptomes collected from two experimental manipulations of microbial mats. The first, a diel study, was conducted in November 2011, while the second, an investigation of the effects of sulfate on community composition, was conducted during this reporting period. For the earlier study, reference-based and reference-free methods were used to assess microbial ecology and genetic partitioning in these complex microbial systems, and that work is available as a pre-print. Four metagenomes from the same experiment were published. In the second, longer (nearly 200 day) manipulation, rRNA iTag libraries for cDNA and DNA were analyzed to determine the effects of sulfate concentration on microbial mat community composition over the course of the experiment. Work on the algal-bacterial association (Chlorella sorokiniana and Azospirillum brasilense) focused initially on demonstrating the transfer of carbon and nitrogen between the partners, using stable isotopic labeling and the LLNL NanoSIMS. Subsequently, the potential role of diazotrophy (nitrogen fixation) by the bacterial partner in supporting the growth of the association was assessed in a series of experiments. It appears to be the case that, although the bacterial partner demonstrably increases the fitness of the algae under nitrogen limitation, and cells of C. sorokiniana receive nitrogen originally fixed from atmospheric nitrogen by A. brasilense, the amount of nitrogen obtained by diazotrophy is too small to explain the increase in fitness.
Analysis of the stress field in the DeSoto canyon Salt Basin for ensuring safe offshore carbon storage
Offshore geologic CO 2 storage offers an attractive option to reduce greenhouse gas emissions. Vast CO 2 storage capacity exists in Cretaceous-Neogene sandstone in the DeSoto Canyon Salt Basin. Understanding the stress and pressure regimes in the basin can help evaluate the geomechanical integrity of the formations, thus minimizing the risk of CO 2 migrating out of the storage complex. Borehole breakouts were identified using four-arm dipmeter logs. Elongation of the breakouts is aligned with the minimum horizontal compressive stress (Sh min ), which tends to be oriented northeast-southwest. Vertical reservoir stresses are influenced by rock and fluid density. Lithostatic and hydrostatic stress each have a power-law relationship to depth. Here, the average lithostatic stress (Sv) gradient is ~21.4 kPa/m. Hydrostatic pressure gradient increases with brine density to a maximum of ~12.2 kPa/m. Geometric mean of the Shmin-depth values correspond to an effective Sh min - effective Sv quotient of ~0.5. Injection pressure can be maintained safely below the estimated effective minimum horizontal stress, thereby reducing the risk of cross-formational flow. Future study should focus on further constraint of geomechanical properties, reservoir integrity, and seal integrity.
Crystallography, Morphology, Electronic Structure, and Transport in Non-Fullerene/Non-Indacenodithienothiophene Polymer:Y6 Solar Cells
Explore the source record for details and available documents.