Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “deposition optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Crack mitigation and wear performance of high-strength steel coatings deposited by high-speed laser cladding

This article investigates the fabrication of defect-free Rockit® 606, a high‑carbon, vanadium- and chromium-enriched precipitation-hardening martensitic steel coating, using high-speed laser cladding (HSLC). Compared to conventional laser cladding, HSLC offers higher deposition efficiency, improved coating quality, minimal thermal distortion, and a reduced heat-affected zone. Various HSLC parameters—including laser power, travel speed, powder feed rate, and overlap distance—were optimized to achieve superior coating properties. Microstructural analysis revealed solidification cracks in coatings deposited on carburized steel, regardless of processing parameters. However, preheating the substrate to 250 °C effectively eliminated cracking by reducing thermal gradients. The coatings exhibited a columnar dendritic microstructure, with coarser dendrites near the substrate and finer dendrites towards the surface. Hardness measurements confirmed that all coatings significantly exceeded the industry-specified threshold of 60 HRC, with preheating having minimal effect on overall hardness distribution. Reciprocating sliding wear tests demonstrated a substantial improvement in wear resistance for the defect-free HSLC coatings compared to baseline carburized steel. These findings underscore the potential of HSLC for producing high-performance, wear-resistant coatings suitable for industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Optimizing ICEBERG LArTPC Run Configuration for Data Collection

To ensure accurate data collection and diagnostics of the ICEBERG electronics, simulation runs were completed using a pulser to mimic charge deposition on the LArTPC wires and collect data for analysis and calibration. This analysis is essential for optimizing the detector's performance by identifying the optimal range of DAC values that avoid saturation zones and provide the best experimental results for real non-pulser runs.

Ganguly, Neil↗
DOE OSTI2026

The properties of the nitrogen-vacancy center in milled chemical vapor deposition nanodiamonds

Fluorescent nanodiamonds (FNDs) containing negatively charged nitrogen-vacancy (NV − ) centers are vital for many emerging quantum sensing applications from magnetometry to intracellular sensing in biology. However, developing a scalable fabrication method for FNDs hosting color centers with consistent bulk-like photoluminescence (PL) and spin coherence properties remains a highly desired but unrealized goal. Here, we investigate optimized ball milling of single-crystal diamonds produced via chemical vapor deposition (CVD) and containing 2 ppm of substitutional nitrogen and 0.3 ppm of NV − to achieve this goal. The NV charge state, PL lifetime, and spin properties of bulk CVD diamond samples are directly compared to milled CVD FNDs and commercial high-pressure high-temperature (HPHT) FNDs. We find that on average, the relative contribution of the NV − charge state to the total NV PL is lower and the NV PL lifetime is longer in CVD FNDs compared to HPHT FNDs, both likely due to the lower N s 0 concentration in CVD FNDs. The CVD bulk and CVD FNDs on average show similar average T 1 spin relaxation times of 3.2 ± 0.7 ms and 4.7 ± 1.6 ms, respectively, compared to 0.17 ± 0.01 ms for commercial HPHT FNDs. Our results demonstrate that ball milling of CVD diamonds enables the large-scale fabrication of NV ensembles in FNDs with bulk-like T 1 spin relaxation properties.

chemical vapor deposition↗
NASA NTRSDate not supplied

Comparison of Equivalent System Mass (ESM) and Modeling Results from Improved Heat Loss Approaches for the Carbon Dioxide Deposition (CDep) System

Proper insulation on any type of cryogenic system is essential for its performance to be optimal, as a poorly insulated system will allow for significant heat loss. Different insulation arrangements for CDep were considered, and performance was simulated and measured in Modelica. Heat loss was correlated to cycle time and CO2 deposition efficiency, which led to overall system power usage. Mass, volume, and power consumption were weighted accordingly in the ESM calculations to guide selection of the CDep insulation scheme.

Marian Alcid↗
NASA NTRSDate not supplied

Hot-Fire Testing Results of Additively Manufactured NASA HR-1 towards Large Scale Implementation of Channel Wall Nozzles

Additive manufacturing (AM) has provided new design and manufacturing opportunities to reduce cost and schedules, consolidate parts, and optimize performance. One technique being evaluated is Laser Powder Directed Energy Deposition (LP-DED), which provides a significant increase in scale compared to Laser Powder Bed Fusion (L-PBF). NASA along with industry partners have been developing the LP-DED process to demonstrate internal channel geometry and development components for use in liquid rocket engine channel cooled nozzles. One material that has been the focus of this development is NASA HR-1, an Iron-Nickel based superalloy optimized for use in high pressure hydrogen environments. Material properties and process characterization has been completed on the high density thin-wall material in addition to advancements of the supply chain. NASA has also completed fabrication of several subscale and full scale channel wall nozzles in LP-DED NASA HR-1 and completed hot-fire testing. This includes refinement of the process to produce thin-walls and various channel geometries to meet the requirements for channel wall nozzle applications. This paper will provide an overview of the LP-DED process development, material characterization and properties, component manufacturing, and hot-fire testing. Hot-fire testing was completed for a lander-class 7K-lbf thrust chamber using Liquid Oxygen (LOX)/Methane. The design overview and results from hot-fire testing will be presented in addition to hardware development for future testing on 2K-lbf and 35k-lbf thrust chambers and large-scale manufacturing technology demonstrators.

Paul Gradl↗
DOE OSTI2025

Controlling Preferred Grain Orientation in Vapor-Deposited Metal-Halide Perovskite Thin Films

Metal-halide perovskites are promising semiconductor materials for light-absorber layers in solar cells due to their optimized band gap, defect tolerance, and relative ease of synthesis. In this work, we demonstrate the viability of vapor transport deposition (VTD), a solvent-free processing method, to realize polycrystalline films of both lead iodide (PbI 2 ) and methylammonium lead iodide (MAPbI 3 ) perovskites showing preferential crystallographic orientation. Notable is the difference in perovskite film texturing observed for sequentially and co-deposited VTD films of MAPbI 3 , as well as the lack of strong preferential orientation in solution-processed MAPbI 3 films. While sequential deposition of the perovskite precursors PbI 2 and methylammonium iodide (MAI) leads to a MAPbI 3 film with a limited preferential grain orientation, co-deposited MAPbI 3 films mirror the orientation of excess PbI 2 present in the film. The latter is confirmed by the similar dependence of preferential orientation for PbI 2 and co-deposited MAPbI 3 on underlayer roughness, as well as the emergence of preferential orientation in MAPbI 3 only when excess PbI 2 is present. Both MAPbI 3 and PbI 2 films show a strong preferred lattice orientation on smooth substrates, while on rougher substrates, this orientation is disrupted. Furthermore, these results are interpreted as excess PbI 2 frustrating the diffusion of MAI in the film, which would otherwise disrupt the preferred orientation, pointing to a notable difference in lattice orientation arising from processing technique and conditions.

Deposition↗
NASA NTRS1974

Investigation of the growth of garnet films by liquid phase epitaxy

Liquid phase expitaxy was investigated to determine its applicability to fabricating magnetic rare earth garnet films for spacecraft data recording systems. Two mixed garnet systems were investigated in detail: (1) Gd-Y and (2) Eu-Yb-Y. All films were deposited on Gd3Ga5012 substrates. The uniaxial anisotropy of the Gd-Y garnets is primarily stress-induced. These garnets are characterized by high-domain wall mobility, low coercivity and modest anisotropy. Characteristic length was found to be relatively sensitive to temperature. The Eu-Yb-Y garnets exhibit acceptable mobilities, good temperature stability and reasonable quality factors. The uniaxial anisotropy of these garnets is primarily growth-induced. The system is well suited for compositional "tailoring" to optimize specific desirable properties. Liquid phase epitaxy can be used to deposit Gd3Ga5012 spacing layers on magnetic garnet films and this arrangement possesses certain advantages over more conventional magnetic filmspacing layer combinations. However, it cannot be used if the magnetic film is to be ion implanted.

Moody, J. W.↗
DOE OSTI2025

High-Power Impulse Magnetron Sputter Deposition of Boron Carbide with Full-Face Erosion Magnetron and Mixed Ar-Ne Plasma

Boron carbide (B 4 C) is an attractive inertial confinement fusion ablator material. The fabrication of B4C ablators by magnetron sputtering requires process optimization. To increase process flexibility, here we explore high-power impulse magnetron sputter (HiPIMS) deposition of B 4 C in pure Ar and mixed Ar-Ne plasmas. Here, the results show that higher plasma discharge currents can be reached with a mixed Ar-Ne plasma in the entire working pressure range studied (5 𝑡𝑜 50 mTorr). At 45 mTorr with 10% of Ne in the Ar-Ne mix, high peak target current densities of ~1 A cm −2 were demonstrated. Films deposited with such a mixed Ar-Ne plasma with a full-face erosion magnetron source on substrates biased at −25 V exhibited higher density and improved mechanical properties, albeit with higher compressive residual stresses compared to the case of HiPIMS deposition in a pure Ar plasma. This work demonstrates additional process flexibility of the HiPIMS discharge mode for the deposition of B 4 C coatings.

Ablator capsule↗
DOE OSTI2024

Optimizing ICEBERG LArTPC Run Configuration for Data Collection

To ensure accurate data collection and diagnostics of the ICEBERG electronics, charge injection runs were completed using a pulser to mimic known charge deposition amounts on the LArTPC wires and collect data for analysis and calibration. This analysis is essential for optimizing the detector's performance by identifying the optimal range of DAC values that avoid saturation zones and provide the best experimental results for non-pulser runs.

Ganguly, Neil↗
DOE OSTI2025

Mitigating Transition Metal Dissolution from Mn-rich Cathodes: Influence of Processing and Testing Methods

Manganese-rich oxides continue to gain interest with respect to the development of Earth-abundant options for lithium-ion cathodes. Of the unique challenges that hinder the respective performance of various classes of such materials, manganese dissolution still stands as a common theme. The work herein explores Li 3 PO 4 as a robust surface protection layer on a prototypical, Co-free, manganese-rich cathode in the way of a lithium- and manganese-rich oxide. The study highlights the critical importance of synthesis and processing in realizing optimal performance of a given surface treatment by comparing sol-gel and atomic layer deposition methods. Furthermore, cycling protocols are emphasized as a critical factor in adequately gauging the efficacy of surface protection strategies to mitigate manganese dissolution and the subsequent electrochemical consequence. Optimized Li 3 PO 4 coatings coatings on lithium- and manganese-rich cathode particles are shown to greatly mitigate capacity fade, impedance rise, pore/void formation and mechanical damage during long-term cycling.

Mallick, Subhadip [Argonne National Laboratory (AN↗
NASA NTRS1981

High-efficiency thin-film GaAs solar cells, phase2

Thin GaAs epi-layers with good crystallographic quality were grown using a (100) Si-substrate on which a thin Ge epi-interlayer was grown by CVD from germane. Both antireflection-coated metal oxide semiconductor (AMOS) and n(+)/p homojunction structures were studied. The AMOS cells were fabricated on undoped-GaAs epi-layers deposited on bulk poly-Ge substrates using organo-metallic CVD film-growth, with the best achieved AM1 conversion efficiency being 9.1%. Both p-type and n(+)-type GaAs growth were optimized using 50 ppm dimethyl zinc and 1% hydrogen sulfide, respectively. A direct GaAs deposition method in fabricating ultra-thin top layer, epitaxial n(+)/p shallow homojunction solar cells on (100) GaAs substrates (without anodic thinning) was developed to produce large area (1 sq/cm) cells, with 19.4% AM1 conversion efficiency achieved. Additionally, an AM1 conversion efficiency of 18.4% (17.5% with 5% grid coverage) was achieved for a single crystal GaAs n(+)/p cell grown by OM-CVD on a Ge wafer.

Yeh, Y. C. M.↗
NASA NTRSDate not supplied

Mechanisms of Interfacial Mixing in the Blown Powder Deposition of Inconel 625 to Copper Alloy for Liquid Rocket Engine Applications

There is an increasing need for functional materials to support high heat flux applications and optimize weight by using bimetallic additive manufacturing (AM). While one promising fabrication technology is the use of blown powder directed energy deposition (DED) AM, challenges remain with bi-metallic combinations. Prominent among these challenges is the need to understand mixing of materials at the bimetallic interface for forming stronger, more durable and reliable joints to extend the versatility of AM into critical applications. One application is the manufacturing of combustion chambers with copper-alloy liners and Superalloy structural jackets. In this application, material combinations are selected for effective heat dissipation, using copper, and retention of strength at high temperatures using Inconel 625. Currently, the dominant problem with this configuration is the highly variable strength of the interface and its correlation with deposition parameters. In this study, samples were fabricated at several vendors with Inconel 625 deposited onto wrought C-18150 (Cu-Cr-Zr) to form a bimetallic interface. Characterization of the interfaces were achieved through optical and electron microscopy, mechanical testing of mini tensile specimens, and electron dispersion spectroscopy to understand diffusion and bulk mixing behaviors at the joint. A theoretical framework was constructed in the context of solidification and mixing mechanisms to explain the resulting differences in the interface. This qualitative approach utilized a fluid dynamics perspective to sum the order of magnitudes of the various acting forces on the weld pool during deposition to predict convection trends based off known parameters. The predicted trends for each vendor are compared to obtain a better understanding of how mixing in the molten pool varied based on deposition parameters.

Additive Manufacturing↗
DOE OSTI2026

Growth of Low-Defect WSe 2 Film via High-Purity van der Waals Crystal Precursor

Two-dimensional (2D) semiconducting transition metal dichalcogenides (TMDs) exhibit exceptional electrical and optical properties, empowering their promising prospects for future nanoelectronics. Despite major advances in n-type 2D semiconductors, the field has yet to synthesize high-mobility p-type 2D TMDs, in particular WSe 2 , and systematically query the influence of defects. In this study, we unveil the pivotal role of substitutional impurity defects vis-à-vis the precursor used and growth method employed in defining the quality of 2D p-type WSe 2 . Density functional theory calculations suggest the adverse effect of Fe-, Co-, Ni- and Si-substituted W impurity defects on the mobility of WSe 2 , whereas defects such as O-, S-substituted Se and Mo-substituted W pose negligible impact. Guided by the theory, we pinpoint van der Waals (vdW) crystals, commonly used in mechanical exfoliation, as the optimal precursor, and develop a facile vdW crystal physical vapor deposition (PVD) method to grow high-purity monolayer 2D WSe 2 film (VPVD-WSe 2 ) that is continuous across a centimeter scale. A suite of spectroscopies confirms the markedly reduced defect density of the as-synthesized WSe 2 compared to those by typical chemical vapor deposition methods, and by PVD with commercial or hydrothermal precursors. Scanning tunneling microscopy further evidence the ultralow substitutional impurity defect density of VPVD-WSe 2 , greatly outperforming the control samples and approaching the mechanically exfoliated counterparts. The VPVD-WSe 2 based field-effect transistors exhibit notable electrical performance with record-high field-effect hole mobility up to 112 cm 2 V –1 s –1 at room temperature, exceeding the best-reported monolayer WSe 2 synthesized by chemical vapor deposition and rivaling the mechanically exfoliated 2D WSe 2 flakes.

WSe2↗
DOE OSTI2024

Universal salt-assisted assembly of MXene from suspension on polymer substrates

Abstract Two-dimensional carbides and nitrides, known as MXenes, are promising for water-processable coatings due to their excellent electrical, thermal, and optical properties. However, depositing hydrophilic MXene nanosheets onto inert or hydrophobic polymer surfaces requires plasma treatment or chemical modification. This study demonstrates a universal salt-assisted assembly method that produces ultra-thin, uniform MXene coatings with exceptional mechanical stability and washability on various polymers, including high-performance polymers for extreme temperatures. The salt in the Ti 3 C 2 T x colloidal suspension reduces surface charges, enabling electrostatically hydrophobized MXene deposition on polymers. A library of salts was used to optimize assembly kinetics and coating morphology. A 170 nm MXene coating can reduce radiation temperature by ~200 °C on a 300 °C PEEK substrate, while the coating on Kevlar fabric provides comfort in extreme conditions, including outer space and polar regions.

Science & Technology - Other Topics↗
DOE OSTI2025

An impermeable copper surface monolayer with high-temperature oxidation resistance

Despite numerous efforts involving surface coating, doping, and alloying, maintaining surface stability of metal at high temperatures without compromising intrinsic properties has remained challenging. Here, we present a pragmatic method to address the accelerated oxidation of Cu, Ni, and Fe at temperatures exceeding 200 °C. Inspired by the concept that oxygen (O) itself can effectively obstruct the pathway of O infiltration, this study proposes the immobilization of O on the metal surface. Through extensive calculations considering various elements (C, Al, Si, Ge, Ga, In, and Sn) to anchor O on Cu surfaces, Si emerges as the optimal element. The theoretical findings are validated through systematic sputtering deposition experiments. The introduction of anchoring elements to reinforce Cu–O bonds enables the formation of an atomically thin barrier on the Cu surface, rendering it impermeable to O even at high temperatures (400 °C) while preserving its intrinsic conductivity. This oxidation resistance, facilitated by the impermeable atomic monolayer, opens promising opportunities for researchers and industries to overcome limitations associated with the use of oxidizable metal films.

36 MATERIALS SCIENCE↗
NASA NTRS1999

High Performance Piezoelectric Thin Films for Shape Control in Large Inflatable Structures

The objective of this research and development program was to develop PbZr(1-x)Ti(x)O3 (PZT) and Pb(1-x)Ba(x)Nb2O6 (PBN) materials with large piezoelectric response which are suitable for shape control in large inflatable structures. Two approaches were to be considered: (1) direct deposition of PZT and PBN films on flexible plastic or thin metal foil substrates, and (2) deposition on Si followed by fabrication of hybrid structures on mylar or kapton. Testing in shape control concepts was carried out at JPL and based on their results, the required modifications were made in the final film compositions and deposition techniques. The program objective was to identify and then optimize piezoelectric materials for NASA shape control applications. This involved the bulk piezoelectric and photovoltaic responses and the compatibility of the thin films with appropriate substrate structures. Within the PZT system, Rockwell has achieved the highest reported piezoelectric coefficient (d(sub 33) greater than 100 pC/N) of any ceramic composition. We used this experience in piezoelectric technology to establish compositions that can effectively address the issues of this program. The performance of piezoelectric thin films depends directly on d(sub ij) and Epsilon. The challenge was to find PZT compositions that maintained high d(sub ij) and Epsilon, while also exhibiting a large photovoltaic effect and integrate thin films of this composition into the system structure necessary to meet shape control applications. During the course of this program, several PZT and PLZT compositions were identified that meet these requirements. Two such compositions were successfully used in electrical and optical actuation studies of thin film structures.

Neurgaonkar, R. R.↗
NASA NTRS1999

High Performance Piezoelectric Thin Films for Shape Control in Large Inflatable Structures

The objective of this research and development program was to develop PbZr(1-x)Ti(x)O3 (PZT) and Pb(1-x)Ba(x)Nb2O6 (PBN) materials with large piezoelectric response which are suitable for shape control in large inflatable structures. Two approaches were to be considered: (1) direct deposition of PZT and PBN films on flexible plastic or thin metal foil substrates, and (2) deposition on Si followed by fabrication of hybrid structures on mylar or kapton. Testing in shape control concepts was carried out at JPL and based on their results, the required modifications were made in the final film compositions and deposition techniques. The program objective was to identify and then optimize piezoelectric materials for NASA shape control applications. This involved the bulk piezoelectric and photovoltaic responses and the compatibility of the thin films with appropriate substrate structures. Within the PZT system, Rockwell has achieved the highest reported piezoelectric coefficient (d(sub 33) greater than 100 pC/N) of any ceramic composition. We used this experience in piezoelectric technology to establish compositions that can effectively address the issues of this program. The performance of piezoelectric thin films depends directly on d(sub ij) and epsilin. The challenge was to find PZT compositions that maintained high d(sub ij) and epsilon, while also exhibiting a large photovoltaic effect and integrate thin films of this composition into the system structure necessary to meet shape control applications. During the course of this program, several PZT and PLZT compositions were identified that meet these requirements. Two such compositions were successfully used in electrical and optical actuation studies of thin film structures.

Neurgaonkar, R. R.↗
NASA NTRS2008

A Thermal Precipitator for Fire Characterization Research

Characterization of the smoke from pyrolysis of common spacecraft materials provides insight for the design of future smoke detectors and post-fire clean-up equipment on the International Space Station. A thermal precipitator was designed to collect smoke aerosol particles for microscopic analysis in fire characterization research. Information on particle morphology, size and agglomerate structure obtained from these tests supplements additional aerosol data collected. Initial modeling for the thermal precipitator design was performed with the finite element software COMSOL Multiphysics, and includes the flow field and heat transfer in the device. The COMSOL Particle Tracing Module was used to determine particle deposition on SEM stubs which include TEM grids. Modeling provided optimized design parameters such as geometry, flow rate and temperatures. Microscopy results from fire characterization research using the thermal precipitator are presented.

Meyer, Marit↗