Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “corner”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Stress-intensity factors for corner cracks in rectangular bars

Stress intensity factors are presented for a wide range of quarter-elliptical corner cracks in a rectangular bar. The bars were subjected to remote tension, out-of-plane bending, or in-plane bending loading, and the stress intensity factors were calculated from a three-dimensional finite element analysis using the nodal-force method. For all loadings considered, smaller width bars produce higher normalized stress intensity factors than the larger width bars. For tensile loading, quarter-circular corner cracks give higher stress intensity factors near the free surfaces and lower values in the interior. The results are compared with data in the literature for remote tensile loading.

Raju, I. S.↗
NASA NTRS1989

Cornering and wear characteristics of the Space Shuttle Orbiter nose-gear tire

Tests of the Space Shuttle Orbiter nose-gear tire have been completed at NASA Langley's Aircraft Landing Dynamics Facility. The purpose of these tests was to determine the cornering and wear characteristics of the Space Shuttle Orbiter nose-gear tire under realistic operating conditions. The tire was tested on a simulated Kennedy Space Center runway surface at speeds from 100 to 180 kts. The results of these tests defined the cornering characteristics which included side forces and associated side force friction coefficient over a range of yaw angles from 0 deg to 12 deg. Wear characteristics were defined by tire tread and cord wear over a yaw angle range of 0 deg to 4 deg under dry and wet runway conditions. Wear characteristics were also defined for a 15 kt crosswind landing with two blown right main-gear tires and nose-gear steering engaged.

Davis, Pamela A.↗
NASA NTRS1990

Behavior of surface and corner cracks subjected to tensile and bending loads in Ti-6Al-4V alloy

The behavior of part-through flaws with regard to failure under monotonic loading and their growth under fatigue loading was studied experimentally and analytically. Comparisons are made of experimental values of toughness obtained using surface and corner cracked specimens with those obtained using standard test specimens, and also experimental growth cycles were compared with numerical predictions using the NASA/FLAGRO computer program. Tests were conducted on various types of surface and corner cracks under tensile and bending loads. Room temperature lab air provided the test environment. The material used in this study was the Ti-6Al-4V alloy in the solution treated and aged (STA) and stress relieved condition. Detailed tabulation of the fracture toughness data and results of life prediction using the NASA/FLAGRO program are presented. Fatigue crack growth rates for the part-through cracked specimens are compared with a base curve fitted from the data obtained using standard specimens. The fatigue loading used in the crack growth testing was constant-amplitude sinusoidal type.

Forman, Royce G.↗
NASA NTRS1991

Integrated 119-micron linear corner-cube array

An integrated corner-cube antenna has been designed, fabricated, and measured at 119 microns. The structure consists of a traveling-wave antenna integrated on a 1-micron dielectric membrane and suspended in a longitudinal cavity etched in silicon wafers. The patterns at 119 microns agree well with millimeter-wave patterns measured on a scaled antenna at 222 GHz. A directivity of 18 +/- 0.5 dB is calculated from E- and H-plane measurements. This work demonstrates that high-efficiency integrated corner-cube antennas are easily scalable to terahertz frequencies and could be used for radio-astronomical and plasma-diagnostic applications.

Gearhart, Steven S.↗
NASA NTRS1992

An experimental examination of the effects of incoming boundary layer modifications on the dynamics of a turbulent compression corner interaction

This experimental study examines the effects of modifications to the incoming turbulent boundary layer on the highly separated shock wave/boundary layer interaction generated by an unswept compression corner. Particular focus is placed on the motion of the unsteady separation shock wave. The flowfield was generated by a 28 deg ramp in a Mach 5 flow with a freestream Reynolds number of 50 x 10 exp 6/m. The incoming turbulent boundary layer transitioned naturally and developed under near-adiabatic wall conditions. Modification of the flow entering the interaction was effected through either a single plate boundary layer manipulator (BLM) or riblets. The BLM reduced the length of separation by 35-45 percent and reduced the streamwise extent of the separation shock motion by 36-74 percent. Examination of the flowfield downstream of the BLM showed this result to be due to the inviscid preturning of the flow by the BLM, and not by changes to the boundary layer dynamics. The riblets had no measurable effect on the compression corner interaction.

Mcclure, W. B.↗
NASA NTRS1992

Membrane triangles with corner drilling freedoms. II - The ANDES element

This is the second article in a three-part series on the construction of 3-node, 9-dof membrane elements with normal-to-its-plane rotational freedoms (the so-called drilling freedoms) using parametrized variational principles. In this part, one such element is derived within the context of the assumed natural deviatoric strain (ANDES) formulation. The higher-order strains are obtained by constructing three parallel-to-sides pure-bending modes from which natural strains are obtained at the corner points and interpolated over the element. To attain rank sufficiency, an additional higher-order 'torsional' mode, corresponding to equal hierarchical rotations at each corner with all other motions precluded, is incorporated. The resulting formulation has five free parameters. When these parameters are optimized against pure bending by energy balance methods, the resulting element is found to coalesce with the optimal EFF element derived in Part I. Numerical integration as a strain filtering device is found to play a key role in this achievement.

Felippa, Carlos A.↗
NASA NTRS1992

Behavior of surface and corner cracks subjected to tensile and bending loads in a Ti-6Al-4V alloy

The behavior of part-through flaws with regard to failure under monotonic loading and their growth under fatigue loading was investigated experimentally and analytically. The objective of this paper is to present comparisons of experimental values of toughness obtained using surface- and corner-cracked specimens with those obtained using standard test specimens, and also to compare experimental growth cycles with numerical predictions using the NASA/FLAGRO computer program. Tests were conducted on various types of surface and corner cracks under tensile and bending loads. Room temperature laboratory air provided the test environment. The material used in this investigation was the Ti-6Al-4V alloy in the solution treated and aged (STA) and stress-relieved condition. Detailed tabulation of the fracture toughness data and results of life prediction using the NASA/FLAGRO program are presented. Fatigue crack growth rates for the part-through-cracked specimens are compared with a base curve fitted from the data obtained using standard specimens. The fatigue loading used in the crack growth testing was of constant-amplitude sinusoidal type.

Forman, Royce G.↗
NASA NTRS1992

Downstream influence scaling of turbulent flow past expansion corners

Previous studies of the high-speed viscous inviscid interaction between a turbulent boundary layer and an expansion at a convex corner have noted that surface pressure decreases toward the downstream inviscid value yielded by a Prandtl-Meyer expansion. A downstream influence on the corner is presently identified which is based on the mean surface pressure distribution; a scaling law is proposed for this distance.

Lu, Frank K.↗
NASA NTRS1993

Damping of surface pressure fluctuations in hypersonic turbulent flow past expansion corners

Surface pressure fluctuations of Mach 8 turbulent flow past a 2.5- and a 4.25-deg expansion corner maintained a Gaussian distribution but were severely attenuated by the expansion process. The pressure fluctuations did not recover to those of an equilibrium turbulent flow even though the mean pressures reached downstream inviscid values in four to six boundary-layer thicknesses. The fluctuations were convected with a velocity comparable to that on a flat plate, and they maintained their identities longer for the stronger expansion. The damping of pressure fluctuations at hypersonic Mach numbers, even by small corner angles, may be exploited in fatigue design.

Chung, Kung-Ming↗
NASA NTRS1994

Numerical Simulation of Supersonic Compression Corners and Hypersonic Inlet Flows Using the RPLUS2D Code

A two-dimensional computational code, PRLUS2D, which was developed for the reactive propulsive flows of ramjets and scramjets, was validated for two-dimensional shock-wave/turbulent-boundary-layer interactions. The problem of compression corners at supersonic speeds was solved using the RPLUS2D code. To validate the RPLUS2D code for hypersonic speeds, it was applied to a realistic hypersonic inlet geometry. Both the Baldwin-Lomax and the Chien two-equation turbulence models were used. Computational results showed that the RPLUS2D code compared very well with experimentally obtained data for supersonic compression corner flows, except in the case of large separated flows resulting from the interactions between the shock wave and turbulent boundary layer. The computational results compared well with the experiment results in a hypersonic NASA P8 inlet case, with the Chien two-equation turbulence model performing better than the Baldwin-Lomax model.

Kapoor, Kamlesh↗
NASA NTRS1994

Effects of turbulence compressibility and unsteadiness in compression corner flow

The structure of the separated flow region over a 20 degree compression corner at a free-stream Mach number of 2.84 is investigated computationally using a Reynolds averaged Navier Stokes (R.A.N.S.) solver and kappa-epsilon model. At this Mach number and ramp angle, a steady-state recirculation region of order delta(sub o) is observed, with onset of a 'plateau' in the wall pressure distribution near the corner. At lower ramp angles, separation is negligible, while at an angle of 24 degrees, separation regions of length 2 delta(sub o) are expected. Of interest here is the response of the mathematical model to inclusion of the pressure dilatation term for turbulent kinetic energy. Compared with the experimental data of Smits and Muck (1987), steady-state computations show improvement when the pressure dilatation term is included. Unsteady computations, using both unforced and then forced inlet conditions, did not predict the oscillatory motion of the separation bubble as observed in laboratory experiments. An analysis of the separation bubble oscillation and the turbulent boundary layer (T.B.L.) frequencies for this flow suggests that the bubble oscillations are of nearly the same order as the turbulent frequencies, and therefore difficult for the model to separate and resolve.

Brankovic, A.↗
NASA NTRS1994

Finite-surface method for the Maxwell equations with corner singularities

The finite-surface method for the two-dimensional Maxwell equations in generalized coordinates is extended to treat perfect conductor boundaries with sharp corners. Known singular forms of the grid and the electromagnetic fields in the neighborhood of each corner are used to obtain accurate approximations to the surface and line integrals appearing in the method. Numerical results are presented for a harmonic plane wave incident on a finite flat plate. Comparisons with exact solutions show good agreement.

Vinokur, Marcel↗
NASA NTRS1995

Analysis of corner cracks at hole by a 3-D weight function method with stresses from finite element method

Stress intensity factors for quarter-elliptical corner cracks emanating from a circular hole are determined using a 3-D weight function method combined with a 3-D finite element method. The 3-D finite element method is used to analyze uncracked configuration and provide stress distribution in the region where crack is to occur. Using this stress distribution as input, the 3-D weight function method is used to determine stress intensity factors. Three different loading conditions, i.e. remote tension, remote bending and wedge loading, are considered for a wide range in geometrical parameters. The significance in using 3-D uncracked stress distribution and the difference between single and double corner cracks are studied. Typical crack opening displacements are also provided. Comparisons are made with solutions available in the literature.

Zhao, W.↗
NASA NTRS2000

Three Corner Sat Communications System

Three Corner Satellite is a constellation of three nanosatellites designed and built by students. New Mexico State University has taken on the design of the communications system for this constellation. The system includes the forward link, return link, and the crosslink. Due to size, mass, power, and financial constraints, we must design a small, light, power efficient, and inexpensive communications system. This thesis presents the design of a radio system to accomplish the data transmission requirements in light of the system constraints. In addition to the hardware design, the operational commands needed by the satellite's on-board computer to control and communicate with the communications hardware will be presented. In order for the hardware to communicate with the ground stations, we will examine the link budgets derived from the radiated power of the transmitters, link distance, data modulation, and data rate for each link. The antenna design for the constellation is analyzed using software and testing the physical antennas on a model satellite. After the analysis and testing, a combination of different systems will meet and exceed the requirements and constraints of the Three Corner Satellite constellation.

Anderson, Bobby↗
NASA NTRS2011

Uncertainty Assessments of 2D and Axisymmetric Hypersonic Shock Wave - Turbulent Boundary Layer Interaction Simulations at Compression Corners

This paper is one of a series of five papers in a special session organized by the NASA Fundamental Aeronautics Program that addresses uncertainty assessments for CFD simulations in hypersonic flow. Simulations of a shock emanating from a compression corner and interacting with a fully developed turbulent boundary layer are evaluated herein. Mission relevant conditions at Mach 7 and Mach 14 are defined for a pre-compression ramp of a scramjet powered vehicle. Three compression angles are defined, the smallest to avoid separation losses and the largest to force a separated flow engaging more complicated flow physics. The Baldwin-Lomax and the Cebeci-Smith algebraic models, the one-equation Spalart-Allmaras model with the Catrix-Aupoix compressibility modification and two-equation models including Menter SST, Wilcox k-omega 98, and Wilcox k-omega 06 turbulence models are evaluated. Each model is fully defined herein to preclude any ambiguity regarding model implementation. Comparisons are made to existing experimental data and Van Driest theory to provide preliminary assessment of model form uncertainty. A set of coarse grained uncertainty metrics are defined to capture essential differences among turbulence models. Except for the inability of algebraic models to converge for some separated flows there is no clearly superior model as judged by these metrics. A preliminary metric for the numerical component of uncertainty in shock-turbulent-boundary-layer interactions at compression corners sufficiently steep to cause separation is defined as 55%. This value is a median of differences with experimental data averaged for peak pressure and heating and for extent of separation captured in new, grid-converged solutions presented here. This value is consistent with existing results in a literature review of hypersonic shock-turbulent-boundary-layer interactions by Roy and Blottner and with more recent computations of MacLean.

Gnoffo, Peter A.↗
NASA NTRS2021

Bioinspired Honeycomb Core Design: An Experimental Study of the Role of Corner Radius, Coping, and Interface

The honeybee’s nest has inspired the design of engineering honeycomb core that primarily abstract the hexagonal cell shape and exploit its mass minimizing properties to construct lightweight panels. This work explored three additional design features that are part of the natural honeybee comb but have not been traditionally considered as design features of interest in honeycomb design: the radius at the corner of each cell, the coping at the top of the cell walls, and the interface between cell arrays. These features were first characterized in natural honeycomb using optical and X-ray techniques, and then incorporated into honeycomb core design, and fabricated using an additive manufacturing process. The honeycomb cores were then tested in out-of-plane compression and bending, and since all three design features added mass to the overall structure, all metrics were examined per unit mass to assess performance gains. The study concluded that the addition of an interface increases specific flexural modulus but has little benefit in out-of-plane compression; coping radius positively impacts specific flexural strength; but that the corner radius has no significant effect in bending, and actually is slightly detrimental for out-of-plane compression testing.

honeycomb↗
NASA NTRSDate not supplied

Assessment of Edge-Based Viscous Method for Corner-Flow Solutions on Graphics Processing Units

A highly efficient, edge-based viscous (EBV) discretization method has been recently implemented in a practical, unstructured-grid, node-centered, finite-volume flow solver and evaluated for Reynolds-averaged Navier-Stokes (RANS) formulations. In comparison to a well-established cell-based viscous (CBV) method, the EBV method has demonstrated multifold acceleration of all viscous-kernel computations on general unstructured mixed-element grids. The viscous kernels include evaluation of viscous fluxes, diffusion terms in turbulence models, and the corresponding Jacobian terms. In this paper, an EBV implementation of a nonlinear extension of the Spalart-Allmaras turbulence model, SA-neg-QCR2000, is presented and verified. The SA-neg-QCR2000 model is used for simulating turbulent corner flows. Previously reported EBV computations have been conducted on traditional computing architectures based on central processing units (CPU). This paper assesses benefits of the EBV method on modern high-performance computing architectures based on graphics processing units (GPU). The GPU implementations of the CBV and EBV methods are verified by comparing solutions and iterative convergence with those observed in CPU computations on the same grids. A comprehensive assessment of the EBV speedup on CPU and GPU architectures is presented for established benchmark corner flows, namely, a supersonic flow through a long square duct and a subsonic flow around a NASA juncture flow model.

CFD↗
NASA NTRSDate not supplied

Assessment of Edge-Based Viscous Method for Corner-Flow Solutions on Graphics Processing Units

A highly efficient, edge-based viscous (EBV) discretization method has been recently implemented in a practical, unstructured-grid, node-centered, finite-volume flow solver and evaluated for Reynolds-averaged Navier-Stokes (RANS) formulations. In comparison to a well-established cell-based viscous (CBV) method, the EBV method has demonstrated multifold acceleration of all viscous-kernel computations on general unstructured mixed-element grids. The viscous kernels include evaluation of viscous fluxes, diffusion terms in turbulence models, and the corresponding Jacobian terms. In this paper, an EBV implementation of a nonlinear extension of the Spalart-Allmaras turbulence model, SA-neg-QCR2000, is presented and verified. The SA-neg-QCR2000 model is used for simulating turbulent corner flows. Previously reported EBV computations have been conducted on traditional computing architectures based on central processing units (CPU). This paper assesses benefits of the EBV method on modern high-performance computing architectures based on graphics processing units (GPU). The GPU implementations of the CBV and EBV methods are verified by comparing solutions and iterative convergence with those observed in CPU computations on the same grids. A comprehensive assessment of the EBV speedup on CPU and GPU architectures is presented for established benchmark corner flows, namely, a supersonic flow through a long square duct and a subsonic flow around a NASA juncture flow model.

CFD↗