Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conducting polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

High Temperature Polymers for use in Fuel Cells

NASA Glenn Research Center (GRC) is currently working on polymers for fuel cell and lithium battery applications. The desire for more efficient, higher power density, and a lower environmental impact power sources has led to interest in proton exchanges membrane fuels cells (PEMFC) and lithium batteries. A PEMFC has many advantages as a power source. The fuel cell uses oxygen and hydrogen as reactants. The resulting products are electricity, heat, and water. The PEMFC consists of electrodes with a catalyst, and an electrolyte. The electrolyte is an ion-conducting polymer that transports protons from the anode to the cathode. Typically, a PEMFC is operated at a temperature of about 80 C. There is intense interest in developing a fuel cell membrane that can operate at higher temperatures in the range of 80 C- 120 C. Operating the he1 cell at higher temperatures increases the kinetics of the fuel cell reaction as well as decreasing the susceptibility of the catalyst to be poisoned by impurities. Currently, Nafion made by Dupont is the most widely used polymer membrane in PEMFC. Nafion does not function well above 80 C due to a significant decrease in the conductivity of the membrane from a loss of hydration. In addition to the loss of conductivity at high temperatures, the long term stability and relatively high cost of Nafion have stimulated many researches to find a substitute for Nafion. Lithium ion batteries are popular for use in portable electronic devices, such as laptop computers and mobile phones. The high power density of lithium batteries makes them ideal for the high power demand of today s advanced electronics. NASA is developing a solid polymer electrolyte that can be used for lithium batteries. Solid polymer electrolytes have many advantages over the current gel or liquid based systems that are used currently. Among these advantages are the potential for increased power density and design flexibility. Automobiles, computers, and cell phones require highly efficient power density for lowering emissions and meeting increasing consumer demands. Many of the solutions can be provided by proton exchange membrane fuel cells and lithium batteries. NASA Glenn Research Center has recognized this need, and is presently engaged in a solution. The goals for the summer include mastering synthesis techniques, understanding the reactions occurring during the synthesis, and characterizing the resulting polymer membranes using NMR, DSC, and TGA for the PEMFC and lithium batteries.

Peplowski, Katherine M.↗
DOE OSTI2024

3D printable feedstock inks for signal control or computation

In one aspect the present disclosure relates to a 3D printed signal control backbone apparatus. The apparatus may have a filament including a first material section and a plurality of second material sections. The first material section is bounded on opposing ends by the second material sections. The first material section is formed by an ink having a percolating network of a plurality of chiplets infused in a non-conductive polymer. The plurality of chiplets form electrically responsive elements imparting a predetermined logic function and which are responsive to a predetermined electrical signal. The second material sections are formed by an ink which is electrically conductive.

Murialdo, Maxwell↗
NASA NTRS2008

All-Organic Actuator Fabricated with Single Wall Carbon Nanotube Electrodes

Compliant electrodes to replace conventional metal electrodes have been required for many actuators to relieve the constraint on the electroactive layer. Many conducting polymers have been proposed for the alternative electrodes, but they still have a problem of poor thermal stability. This article reports a novel all-organic actuator with single wall carbon nanotube (SWCNT) films as the alternative electrode. The SWCNT film was obtained by filtering a SWCNT solution through an anodized alumina membrane. The conductivity of the SWCNT film was about 280 S/cm. The performance of the SWCNT film electrode was characterized by measuring the dielectric properties of NASA Langley Research Center - Electroactive Polymer (LaRC-EAP) sandwiched by the SWCNT electrodes over a broad range of temperature (from 25 C to 280 C) and frequency (from 1 KHz to 1 MHz). The all-organic actuator with the SWCNT electrodes showed a larger electric field-induced strain than that with metal electrodes, under identical measurement conditions.

Lowther, Sharon E.↗
NASA NTRS2011

Effect of Reverse Bias Stress on Leakage Currents and Breakdown Voltages of Solid Tantalum Capacitors

The majority of solid tantalum capacitors are produced by high-temperature sintering of a fine tantalum powder around a tantalum wire followed by electrolytic anodization that forms a thin amorphous Ta2O5 dielectric layer and pyrolysis of manganese nitrite on the oxide to create a conductive manganese dioxide electrode. A contact to tantalum wire is used as anode terminal and to the manganese layer as a cathode terminal of the device. This process results in formation of an asymmetric Ta -- Ta2O5 -- MnO2 capacitor that has different characteristics at forward (positive bias applied to tantalum) and reverse (positive bias applied to manganese cathode) voltages. Reverse bias currents might be several orders of magnitude larger than forward leakage currents so I-V characteristics of tantalum capacitors resemble characteristics of semiconductor rectifiers. Asymmetric I-V characteristics of Ta -- anodic Ta2O5 systems have been observed at different top electrode materials including metals, electrolytes, conductive polymers, and manganese oxide thus indicating that this phenomenon is likely related to the specifics of the Ta -- Ta2O5 interface. There have been multiple attempts to explain rectifying characteristics of capacitors employing anodic tantalum pentoxide dielectrics. A brief review of works related to reverse bias (RB) behavior of tantalum capacitors shows that the mechanism of conduction in Ta -- Ta2O5 systems is still not clear and more testing and analysis is necessary to understand the processes involved. If tantalum capacitors behave just as rectifiers, then the assessment of the safe reverse bias operating conditions would be a relatively simple task. Unfortunately, these parts can degrade with time under reverse bias significantly, and this further complicates analysis of the I-V characteristics and establishing safe operating areas of the parts. On other hand, time dependence of reverse currents might provide additional information for investigation of the processes under reverse bias conditions. In practice, there were instances when, due to unforeseen events, the system operated at conditions when capacitors experience periodically a relatively small reverse bias for some time followed by normal, forward bias conditions. In such a case an assessment should be made on the degree to which these capacitors are degraded by application of low-voltage reverse bias, and whether this degradation can be reversed by normal operating conditions. In this study, reverse currents in different types of tantalum capacitors were monitored at different reverse voltages below 15%VR and temperatures in the range from room to 145 C for up to 150 hours to get better understanding of the degradation process and determine conditions favorable to the unstable mode of operation. The reversibility of RB degradation has been evaluated after operation of the capacitors at forward bias conditions. The effect of reverse bias stress (RBS) on reliability at normal operating conditions was evaluated using highly accelerated life testing at voltages of 1.5VR and 2 VR and by analysis of changes in distributions of breakdown voltages. Possible mechanisms of RB degradation are discussed.

Teverovsky, Alexander A.↗
NASA NTRS2012

In-Situ Wire Damage Detection System

An In-Situ Wire Damage Detection System (ISWDDS) has been developed that is capable of detecting damage to a wire insulation, or a wire conductor, or to both. The system will allow for realtime, continuous monitoring of wiring health/integrity and reduce the number of false negatives and false positives while being smaller, lighter in weight, and more robust than current systems. The technology allows for improved safety and significant reduction in maintenance hours for aircraft, space vehicles, satellites, and other critical high-performance wiring systems for industries such as energy production and mining. The integrated ISWDDS is comprised of two main components: (1) a wire with an innermost core conductor, an inner insulation film, a conductive layer or inherently conductive polymer (ICP) covering the inner insulation film, an outermost insulation jacket; and (2) smart connectors and electronics capable of producing and detecting electronic signals, and a central processing unit (CPU) for data collection and analysis. The wire is constructed by applying the inner insulation films to the conductor, followed by the outer insulation jacket. The conductive layer or ICP is on the outer surface of the inner insulation film. One or more wires are connected to the CPU using the smart connectors, and up to 64 wires can be monitored in real-time. The ISWDDS uses time domain reflectometry for damage detection. A fast-risetime pulse is injected into either the core conductor or conductive layer and referenced against the other conductor, producing transmission line behavior. If either conductor is damaged, then the signal is reflected. By knowing the speed of propagation of the pulse, and the time it takes to reflect, one can calculate the distance to and location of the damage.

Williams, Martha↗
NASA NTRS1978

Thermochemical and flammability properties of some thermoplastic and thermoset polymers - A review

The thermochemical and flammability properties of thermoplastic and thermoset polymers are discussed. The results of a thermogravimetric analysis of the polymers conducted on a DuPont 950 thermogravimetric analyzer using both nitrogen and air atmospheres are presented. Experimental data on smoke evolution are given, and the methodology for assessing the relative toxicity of the pyrolysis effluents is described. The values obtained from the flammability tests are compared with the stoichiometric char yield, and it is shown that the ignition tendency of the polymers is a linear function of the resin char yield

Kourtides, D. A.↗
NASA NTRS1994

Method development for compensating temperature effects in pressure sensitive paint measurements

Pressure sensitive luminescent paints (PSP) have recently emerged as a viable technique for aerodynamic pressure measurements. The technique uses a surface coating which contains probe molecules that luminesce when excited by light of an appropriate wavelength. The photoluminescence of these materials is known to be quenched by the presence of molecular oxygen. Since oxygen is a fixed mole fraction of the air, the coating's luminescence intensity varies inversely with air pressure. Digital imaging of the luminescence varying across a coated surface produces a pressure distribution map over that surface. One difficulty encountered with this technique is the temperature effect on the luminescence intensity. Present PSP formulations have significant sensitivity to temperature. At the moment, the most practical way of correcting for temperature effects is to calibrate the paint in place at the operating temperatures by using a few well-placed pressure taps. This study is looking at development of temperature indicating coatings that can be applied and measured concurrently with PSP, and use the temperature measurement to compute the correct pressure. Two methods for this dual paint formulation are proposed. One method will use a coating that consists of temperature sensitive phosphors in a polymer matrix. This is similar in construction to PSP, except that the probe molecules used are selected primarily for their temperature sensitivity. Both organic phosphors (e.g., europium thenoyltrifluoroacetonate, bioprobes) and inorganic phosphors (e.g., Mg4(F)GeO6:Mn, La2O2S:Eu, Radelin Type phosphors, Sylvania Type phosphors) will be evaluated for their temperature sensing potential. The next method will involve a novel coating composing of five membered heterocyclic conducting polymers which are known to show temperature dependent luminescence (e.g., poly(3-alkylthiopene), poly(3-alkylselenophene), poly(3-alkylfuran)). Both methods will involve applying a bottom layer of temperature sensitive coating followed by a top coating of PSP. An oxygen-impermeable polymer can be used as the temperature sensitive coating matrix, or it can be layered in between the coatings to prevent oxygen quenching of the bottom coating's luminescence. The probe molecules of the coatings will be excited by a broad band of light, with the different emissions detected and measured at their distinct wavelengths. Developmental research of these coatings is still in progress; however, preliminary results look very promising.

Demandante, Carlo Greg N.↗
NASA NTRS2018

Anomalous Transients in Chip Polymer Tantalum Capacitors

Contrary to MnO2 tantalum capacitors, transient processes in polymer tantalum capacitors after voltage application might result in anomalously high, ampere-level currents when a capacitor might appear as a short circuit for a time that is much greater than a transient time in MnO2 capacitors. In this work, conditions that cause anomalous transients in different types of polymer tantalum capacitors have been analyzed. Related phenomena that included increasing of capacitance and dissipation factors with voltage, parametric surge current test failures without damage to capacitors, and increasing leakage currents at low temperatures are described. It has been shown that anomalous transients increased substantially with applied voltage and with reduction of moisture content in capacitors caused by storage or operation at high temperatures and/or in vacuum. Different types of capacitors exhibited different level of transients and modification of conductive polymers or process of their application might decrease transient leakage currents substantially. For space applications, the risk of failures related to anomalous transients can be mitigated by special testing procedures to select parts with an acceptable level of transients and by voltage derating.

Tantalum Capacitors↗
NASA NTRS2004

Thermal characteristics of Lithium-ion batteries

Lithium-ion batteries have a very promising future for space applications. Currently they are being used on a few GEO satellites, and were used on the two recent Mars rovers Spirit and Opportunity. There are still problem that exist that need to be addressed before these batteries can fully take flight. One of the problems is that the cycle life of these batteries needs to be increased. battery. Research is being focused on the chemistry of the materials inside the battery. This includes the anode, cathode, and the cell electrolyte solution. These components can undergo unwanted chemical reactions inside the cell that deteriorate the materials of the battery. During discharge/ charge cycles there is heat dissipated in the cell, and the battery heats up and its temperature increases. An increase in temperature can speed up any unwanted reactions in the cell. Exothermic reactions cause the temperature to increase; therefore increasing the reaction rate will cause the increase of the temperature inside the cell to occur at a faster rate. If the temperature gets too high thermal runaway will occur, and the cell can explode. The material that separates the electrode from the electrolyte is a non-conducting polymer. At high temperatures the separator will melt and the battery will be destroyed. The separator also contains small pores that allow lithium ions to diffuse through during charge and discharge. High temperatures can cause these pores to close up, permanently damaging the cell. My job at NASA Glenn research center this summer will be to perform thermal characterization tests on an 18650 type lithium-ion battery. High temperatures cause the chemicals inside lithium ion batteries to spontaneously react with each other. My task is to conduct experiments to determine the temperature that the reaction takes place at, what components in the cell are reacting and the mechanism of the reaction. The experiments will be conducted using an accelerating rate calorimeter (ARC), which uses a heat-wait-search mode until an exothermic reaction is detected. After an exotherm is found the calorimeter maintains an adiabatic environment around a bomb which holds the test sample. The ARC will help identify important reactions and what temperature these exothermic reactions take place at. In order fully understand the battery, we are first going to take apart the battery and test the individual components of the battery using the ARC. I will first conduct a test on the electrolyte solution by itself. We will then test the electrolyte solution with the anode. We would like to see how the electrolyte solution reacts with the anode and its binder material. The next would be the same test using the cathode instead of the anode. By comparing the results of the electrolyte, electrolyte with anode, and the electrolyte with the cathode we can determine the reactions that are taking place due to each component. Using the heat capacity of the each individual sample and the temperature by which the sample increases, kinetic and thermo-dynamical information can then be found. A Gas chromatograph could be used to help with the task of identifying the by-products at the end of each test. One way of increasing the cycle life is to increase the stability of the materials inside the

Hauser, Dan↗
DOE OSTI2025

Visualizing energy transfer between redox-active colloids

Redox-active colloids (RACs) represent a novel class of energy carriers that exchange electrical energy upon contact. Understanding contact-mediated electron transfer dynamics in RACs offers insights into physical contact events in colloidal suspensions and enables quantification of electrical energy transport in nonconjugated polymers. Redox-based electron transport was directly observed in monolayers of micron-sized RACs containing ethyl-viologen side groups via fluorescence microscopy through an unexpected nonlinear electrofluorochromism that is quantitatively coupled to the redox state of the colloid. Via imaging studies, using this electrofluorochromism, the apparent charge transfer diffusion coefficient D CT of the RAC was easily determined. The visualization of energy transport within suspensions of redox-active colloids was also demonstrated. Our work elucidates fundamental mechanisms of energy transport in colloidal systems, informs the development of next-generation redox flow batteries, and may inspire new designs of smart active soft matter including conductive polymers for applications ranging from electrochemical sensors and organic electronics to colloidal robotics.

Qu, Alan Subing [Univ. of Illinois at Urbana-Champ↗
DOE OSTI2025

High‐Performance Low‐Emissivity Paints Enabled by N‐Doped Poly(benzodifurandione) (n‐PBDF) for Energy‐Efficient Buildings

Abstract Low‐emissivity (low‐e) paints reduce radiative heat exchange between buildings and the environment, stabilizing indoor climates and lowering air conditioning demand. However, low‐cost, durable, and colored low‐e paints have yet to be demonstrated. Here, an approach is proposed using n‐doped poly(benzodifurandione) (n‐PBDF), a transparent organic conducting polymer, coated over colored commercial paints. This achieves a low thermal emissivity of 0.19 in the mid‐infrared spectrum, attributed to the efficient charge transport of delocalized π‐electrons in n‐PBDF structure. The reduction in thermal emissivity aids in regulating building temperatures by minimizing heat transfer between buildings and their surroundings across diverse climate zones and seasons. The n‐PBDF coating preserves the underlying paint's color due to its high visible transparency, meeting aesthetic requirements. It also shows strong stability in accelerated indoor weathering tests, ensuring long‐term performance. Simulations estimate annual HVAC energy savings of over 10,800 kWh in San Francisco and 5,500 kWh in Chicago for the typical mid‐rise apartments. The paint's versatility, scalability, and durability make it suitable for buildings, vehicles, and greenhouses, aiding urban heat island mitigation.

Liu, Xiaojie [School of Mechanical Engineering and↗
DOE OSTI2025

Local heat transfer measurement in a volumetrically heated TPMS lattice using distributed optical fiber thermal sensing

As additive manufacturing continues to reduce design constraints on heat exchange geometries, methods for high-fidelity local heat transfer measurements in nonconventional channel geometries are critical to their continued development. This study presents a novel method for measuring local heat transfer performance in volumetrically heated lattices using a distributed optical fiber temperature sensor. A diamond-type triply periodic minimal surface (TPMS) lattice, 3D-printed from a conductive polymer, was Joule heated while it was convectively cooled with air. Temperature measurements were taken at the solid–fluid interface across 14 internal locations using a single optical fiber over the Reynolds number range 800–2750. The TPMS lattice achieved up to 312% higher heat transfer coefficients compared to developing flow in a straight tube. A Nusselt number correlation was developed for the diamond TPMS, which showed good agreement with data collected for comparable geometries available in literature. In conclusion, this study presents a robust and new method for experimental measurement of the heat transfer coefficient in complex geometries and helps to understand and quantify the exceptional performance of TPMS heat transfer geometries.

TPMS↗
DOE OSTI2026

Interface-engineered (CrMnTiZnCo) 3 O 4 @polypyrrole nano-hybrids for superior lithium storage

High-entropy oxides (HEO) have emerged as promising anode materials for lithium-ion batteries (LIBs) due to their high theoretical specific capacity. However, their practical application is hindered by several challenges, including significant volume expansion, electrode pulverization, and substantial irreversible capacity loss during initial cycles. To address these limitations, this study designed a novel core-shell composite material, denoted as HEO@PPy, which consists of a (CrMnTiZnCo) 3 O 4 -based HEO core and a polypyrrole (PPy) shell. This composite demonstrates remarkable electrochemical performance: it maintains a specific capacity of 1090.1 mAh/g after 100 cycles at 100 mA/g and retains 521.8 mAh/g after 1000 cycles at 1 A/g, highlighting its superior cycling stability. Furthermore, it exhibits excellent rate capability, delivering a capacity of 372.1 mAh/g even at a high current density of 5 A/g. These findings confirm that the strategic compositional and structural design of HEOs, combined with hybridization with conductive polymers like PPy, provides a viable pathway for developing advanced anode materials for next-generation, high-performance lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Understanding the effect of organic coatings on 4-nitrostyrene hydrogenation selectivity over Pt/TiO 2 catalysts

The hydrogenation of 4-nitrostyrene was investigated over Pt/TiO 2 catalysts to understand the effects of different catalyst coatings on product selectivity and reaction rates. This reaction is a much-investigated selectivity probe due to difficulty in controlling reactivity between the nitro and vinyl groups of 4-nitrostyrene, with C=C reduction generally being more favorable. 4-Nitrostyrene hydrogenation reactions were carried out in a batch reactor using uncoated, organothiol coated, phosphonic acid (PA) coated, and ion-conducting polymer (ionomer) coated catalysts. Thiols form dense coatings on Pt surfaces, whereas PAs preferentially accumulate on TiO 2 ; ionomer binding preference is unknown for this type of catalyst. The coating densities of the thiols and PAs were varied to observe the effects of loading on catalytic activity and reaction selectivity relative to the uncoated catalyst. Changes in selectivity were observed for catalysts with all coatings, with thiol coatings shifting selectivity towards the nitro reduction product, 4-vinylaniline (4-VA), and both ionomer and PA coatings shifting towards 4-ethylnitrobenzene, the olefin hydrogenation product. It was observed that selectivity toward 4-VA increased with thiol coating density, where 1,2-benzenedithiol (BDT) coated catalysts exhibited a selectivity of >99%. These changes were attributed to the identity of the adsorption sites blocked by the different coatings: blocking of metal sites via thiols decreased the rate of C=C hydrogenation, whereas blocking of TiO 2 sites by PAs decreased the rate of nitro group hydrogenation. The changes observed for ionomer and PA coatings suggested that ionomers, like PAs, bind preferentially to the metal oxide support rather than the active metal. This work provides new support to the proposal that nitro group hydrogenation preferentially occurs on TiO 2 sites after hydrogen spillover and underscores how selection of ligand functionality can be used to tune catalyst selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

(CrMnCoNiZn) 3 O 4 @PPy core-shell nanocomposite with excellent electrochemical performance as lithium-ion battery anode

High entropy oxides (HEOs) have an excellent potential for use as electrode materials in lithium-ion batteries (LIBs) due to their high theoretical specific capacity. In this work, spinel-structured (CrMnCoNiZn) 3 O 4 HEO nanoparticles with five elements in equal molar ratio is first generated by solution combustion method. (CrMnCoNiZn) 3 O 4 @polypyrrole (PPy) nanocomposites are prepared by in-situ polymerization method. As an anode for lithium-ion batteries, the electrochemical performance of the (CrMnCoNiZn) 3 O 4 @PPy composite outperforms that of (CrMnCoNiZn) 3 O 4 nanoparticles. The capacity is 802 mAh/g after 100 cycles at a current density of 100 mA/g, 416 mAh/g after 1000 cycles at a high current density of 1 A/g, and 360 mAh/g rate capacity at 2 A/g. The excellent electrochemical performance of the composites is mainly due to the fact that the conductive and flexible PPy is encapsulated on the high-entropy oxides, which can alleviate the volume change triggered by extraction-insertion of lithium ions process, as well as enhance the electrical conductivity and reduce the occurrence of some side reactions. Finally, this method of compositing materials can also be used in other HEOs and conductive polymers, providing a new idea to enhance the electrochemical properties of HEOs.

25 ENERGY STORAGE↗
DOE OSTI2026

Computational Insights into the Salt-Induced Modulation of Electron Transporting Conjugated Polyelectrolytes

The morphological and electronic properties of conjugated polyelectrolytes (CPEs) are highly sensitive to their ionic environment and remain poorly understood. To elucidate structure–property relationships in CPEs, we investigate the role of salt concentration on CPE morphology and hole conductivity using a quantum mechanically informed coarse-grained (CG) model coupled with semiclassical rate theory. Under good solvent conditions, high salt concentration induces torsional disorder along the conjugated backbone, decreasing hole delocalization. In contrast, under poor solvent conditions, high salt concentration promotes CPE aggregation, leading to thicker fibers and increased hole mobilities. Collectively, this work characterizes the competing interactions governing CPE assembly and hole transport as a function of salt concentration, highlighting ion engineering as a powerful strategy for tailoring the properties of mixed-conducting polymers.

diseases↗
DOE OSTI2025

Enhancing cathode composites with conductive alignment synergy for solid-state batteries

Enhancing transport and chemomechanical properties in cathode composites is crucial for the performance of solid-state batteries. Our study introduces the filler-aligned structured thick (FAST) electrode, which notably improves mechanical strength and ionic/electronic conductivity in solid composite cathodes. The FAST electrode incorporates vertically aligned nanoconducting carbon nanotubes within an ion-conducting polymer electrolyte, creating a low-tortuosity electron/ion transport path while strengthening the electrode’s structure. This design not only mitigates recrystallization of the polymer electrolyte but also establishes a densified local electric field distribution and accelerates the migration of lithium ions. The FAST electrode showcases outstanding electrochemical performance with lithium iron phosphate as the active material, achieving a high capacity of 148.2 milliampere hours per gram at 0.2 C over 100 cycles with substantial material loading (49.3 milligrams per square centimeter). This innovative electrode design marks a remarkable stride in addressing the challenges of solid-state lithium metal batteries.

Science & Technology - Other Topics↗
DOE OSTI2025

Thrifting iridium for hydrogen

Using renewable electricity to produce hydrogen fuel reduces reliance on fossil fuels. Proton exchange membrane water electrolyzers (PEMWEs) are the highest-performing commercialized technology. These devices split water into oxygen gas and hydrogen ions (protons) at the anode. The protons then migrate through an ion-conducting polymer membrane (ionomer) to be reduced to hydrogen gas at the cathode. Further, the anode reaction’s harsh environment requires the use of precious-metal catalysts, such as iridium oxide (IrO x ). Given the expense and scarcity, the design of electrodes that minimize the use of precious metals without compromising the requisite stability and activity is desired for large-scale hydrogen production. On page 791 of this issue, Shi et al. report that anchoring IrO x catalysts onto porous cerium-oxide (CeO x ) supports maintains performance even with much reduced precious metal use.

08 HYDROGEN↗